[POWERPC] EEH: Power4 systems sometimes need multiple resets.
On detection of an EEH error, some Power4 systems seem to occasionally
want to be reset twice before they report themselves as fully recovered.
This patch re-arranges the code to attempt additional resets if the first
one doesn't take.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Maple U3 HT - reject inappropriate config space access
When there is a PCI-X mode 2 capable device behind the HT<->PCI-X
bridge, the pci core decides that the device has the extended 4K
config space, even though the bus is not operating in mode 2. This is
because the u3_ht pci ops silently accept offsets greater than 255 but
use only the 8 least significant bits, which means reading at offset
0x100 gets the data at offset 0x0, and causes confusion for lspci.
Reject accesses to configuration space offsets greater than 255.
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Thu, 21 Sep 2006 18:10:51 +0000 (13:10 -0500)]
[POWERPC] Fix IPIC pending register assignments
This patch fixes the assignment of pending registers to IRQ numbers for
the IPIC; the code previously assigned all IRQs to the high pending word
regardless of which word the interrupt belonged to.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] powerpc: fix building gdb against asm/ptrace.h
Ulrich Weigand found a bug with the current version of the
asm-powerpc/ptrace.h that prevents building at least the
SPU target version of gdb, since some ptrace opcodes are
not defined.
The problem seems to have originated in the merging of 32 and
64 bit versions of that file, the problem is that some opcodes
are only valid on 64 bit kernels, but are also used by 32 bit
programs, so they can't depends on the __powerpc64__ symbol.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 21 Sep 2006 08:21:35 +0000 (18:21 +1000)]
[POWERPC] Remove DISCONTIGMEM cruft from page.h
This looks like cruft to me, these functions don't exist AFAICT,
and I can't see that it's possible to even enable DISCONTIGMEM on
powerpc anymore. CC'ing some folks who might know better, based on
the who-touched-it-last principle.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own. One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects a pci_dev get/put imbalance that can occur only in
highly unlikely situations (kmalloc failures, pci devices with
overlapping resource addresses). No actual failures seen, this was
spotted during code review.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] PPC: Fix xmon stack frame address in backtrace
The stack frame address was being printed incorrectly in the backtrace
option of XMON on PPC. This patch fixes it to print the actual stack
address instead of the address of the local variable that contains it.
Signed-off-by: Josh Boyer <jdub@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Peter Bergner [Thu, 14 Sep 2006 19:18:38 +0000 (14:18 -0500)]
[POWERPC] Add AT_PLATFORM value for Xilinx Virtex-4 FX
Jakub noticed the cputable.c entry for Xilinx Virtex-4 FX was missing
a .platform value, so the AT_PLATFORM value wouldn't be set correctly.
This adds it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Tue, 19 Sep 2006 04:06:27 +0000 (14:06 +1000)]
[POWERPC] Define of_read_ulong helper
There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Stephen Rothwell [Tue, 19 Sep 2006 04:51:40 +0000 (14:51 +1000)]
[POWERPC] remove unused io accessors
The io accessors insw_ns, outsw_ns, insl_ns and outsl_ns are unused
(except for one unnecessary use in drivers/net/3c509.c that is addressed
in a previous patch) and are only defined in powerpc/ppc, so remove them.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Olof Johansson [Wed, 13 Sep 2006 18:32:39 +0000 (13:32 -0500)]
[POWERPC] Fix non-smp build
This fixes a compile error that only surfaces on CONFIG_SMP=n builds;
<asm/hvcall.h> seems to get pulled in through another header file for
SMP builds. This problem was introduced by the hvcall stats patch.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mike Miller [Wed, 13 Sep 2006 03:36:07 +0000 (20:36 -0700)]
[PATCH] cciss: version update, new hw
Add support for new hardware and bumps the version to 3.6.10. It seems
there were several changes introduced including soft_irq. I decided to
bump the major number to reflect these changes. Since we're still
supporting older vendor kernels I need some way differentiate between
kernel versions <=2.6.10 and newer kernels >=2.6.16.
Signed-off-by: Mike Miller <mike.miller@hp.com> Cc: Jens Axboe <axboe@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Woodhouse [Wed, 13 Sep 2006 03:36:06 +0000 (20:36 -0700)]
[PATCH] headers_check: fix userspace build of asm-mips/page.h
MIPS asm/page.h unconditionally includes <asm-generic/memory_model.h>, which
doesn't exist in userspace. Move an #endif /* __KERNEL__ */ down a few lines
to prevent that.
Also, remove the broken definition of PAGE_SIZE which is never going to be
correct -- in the absence of PAGE_SIZE, non-broken userspace will fall back to
using sysconf() or getpagesize() instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Woodhouse [Wed, 13 Sep 2006 03:36:05 +0000 (20:36 -0700)]
[PATCH] headers_check: don't expose PFN stuff to userspace in <asm-i386/setup.h>
The header file <linux/pfn.h> doesn't exist in userspace and probably
shouldn't -- but it's used unconditionally in <asm-i386/setup.h>. Protect it
with #ifdef __KERNEL__ and move setup.h from $(header-y) to $(unifdef-y) in
Kbuild accordingly.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Woodhouse [Wed, 13 Sep 2006 03:36:04 +0000 (20:36 -0700)]
[PATCH] headers_check: move kernel-only #includes within <asm-i386/elf.h>
Some files which don't exist in userspace were being included unconditionally
in asm-i386/elf.h. Move the offending #includes down a few lines so that
they're protected by #ifdef __KERNEL__
In fact, we probably want to kill off all userspace use of asm/elf.h -- but we
aren't there yet, so we should at least make it possible to include it for
now.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Woodhouse [Wed, 13 Sep 2006 03:36:03 +0000 (20:36 -0700)]
[PATCH] headers_check: remove <asm/timex.h> from user export
There's useful stuff in <linux/timex.h> but <asm/timex.h> has nothing for
userspace. Stop exporting it, and include it only from within the existing
#ifdef __KERNEL__ part of <linux/timex.h>
This fixes a 'make headers_check' failure on i386 because asm-i386/timex.h
includes both asm-i386/tsc.h and asm-i386/processor.h, neither of which are
exported to userspace. It's not entirely clear _why_ it includes either of
these, but it does.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Woodhouse [Wed, 13 Sep 2006 03:36:02 +0000 (20:36 -0700)]
[PATCH] headers_check: reduce user-visible noise in <linux/nfs_fs.h>
We don't need any of this crap included from the user-visible part of nfs_fs.h
-- remove it all.
In fact, we probably don't need anything but NFS_SUPER_MAGIC to be defined; is
there any need for anything else? And magic numbers should probably move to
<linux/magic.h> rather than being strewn across various fs-specific include
files which exist in userspace for solely that purpose.
With this patch, 'make header_check' works again at least on PowerPC.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] alim15x3.c: M5229 (rev c8) support for DMA cd-writer
Configuration bits are not set properly for DMA on some chipset revisions.
It has already been corrected for M5229 (rev c7) but not for M5229 (rev
c8). This leads to the bug described at
http://bugzilla.kernel.org/show_bug.cgi?id=5786 (lost interrupt + ide bus
hangs).
Signed-off-by: Michael De Backer <micdb@skynet.be> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] We can not allow anonymous contributions to the kernel
The DCO does not mean anything if we allow anonymous contributors to the
kernel. As this is an open source project, we need to do everything in the
open.
[PATCH] lockdep: double the number of stack-trace entries
Miles Lane reported the "BUG: MAX_STACK_TRACE_ENTRIES too low!" message,
which means that during normal use his system produced enough lockdep
events so that the 128-thousand entries stack-trace array got exhausted.
Double the size of the array.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Miles Lane <miles.lane@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] libata: ignore CFA signature while sanity-checking an ATAPI device
0x848a in ID word 0 indicates CFA device iff the ID data is obtained from
IDENTIFY DEVICE. For ATAPI devices, 0x848a in ID work 0 indicates valid
ATAPI device. Fix sanity check in ata_dev_read_id() such that ATAPI
devices reporting 0x848a in ID word 0 is not handled as error.
The problem is identified by J.A. Magallon with HL-DT-ST DVDRAM GSA-4120B.
Signed-off-by: Tejun Helo <htejun@gmail.com> Cc: J.A. Magallon <jamagallon@ono.com> Acked-by: Jeff Garzik <jeff@garzik.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[POWERPC] Fix G5 DART (IOMMU) race causing occasional data corruption
It seems that the occasional data corruption observed with the tg3
driver wasn't due to missing barriers after all, but rather seems to
be due to the DART (= IOMMU) in the U4 northbridge reading stale
IOMMU table entries from memory due to a race. This fixes it by
making the CPU read the entry back from memory before using it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Wed, 13 Sep 2006 12:08:26 +0000 (22:08 +1000)]
[POWERPC] Fix MMIO ops to provide expected barrier behaviour
This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Olaf Hering [Fri, 8 Sep 2006 14:29:21 +0000 (16:29 +0200)]
[POWERPC] print backtrace when entering xmon
xmon does not print a backtrace per default. This is bad on systems with
USB keyboard, the most needed info about the crash is lost.
print a backtrace during the very first xmon entry.
Booting with xmon=nobt disables the autobacktrace functionality.
Signed-off-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Thu, 7 Sep 2006 20:18:08 +0000 (15:18 -0500)]
[POWERPC] Quiet hvc_console console output on failed opens
No other tty driver will print on the console when the open of it fails.
On systems that happen to be configured for both ttyS0 and hvc0 console,
this will keep flooding the console output. This is most likely to
happen with systems booted between with and without hypervisor from the
same filesystem.
Let's just remove it. When it's really needed (i.e. when the open fails
and someone is trying to debug it), noone will see the output anyway. And
init will report the opens failing in due time through the syslog.
Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Ryan S. Arnold <rsa@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the following whitespace warnings when compiling with ARCH=ppc
arch/ppc/Kconfig:1207:warning: leading whitespace ignored
arch/ppc/Kconfig:1226:warning: leading whitespace ignored
arch/ppc/Kconfig:1231:warning: leading whitespace ignored
Also fix a typo ("Supprt").
Signed-off-by: Josh Boyer <jdub@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mike Kravetz [Wed, 6 Sep 2006 23:23:12 +0000 (16:23 -0700)]
[POWERPC] powerpc: Instrument Hypervisor Calls
Add instrumentation for hypervisor calls on pseries. Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs. Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Wed, 6 Sep 2006 19:35:19 +0000 (14:35 -0500)]
[POWERPC] powerpc: Divorce CPU_FTR_CTRL from CPU_FTR_PPCAS_ARCH_V2_BASE
The performance monitor implementation (including CTRL register behaviour)
is just included in PPC v2 as an example, it's not truly part of the base.
It's actually a somewhat misleading feature, but I'll leave that be for
now: The presence of the register is not what the feature bit is used
for, but instead it's used to determine if it contains the runlatch
bit for idle reporting of the performance monitor. For alternative
implementations, the register might still exist but the bit might have
different meaning (or no meaning at all).
For now, split it off and don't include it in CPU_FTR_PPCAS_ARCH_V2_BASE.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Wed, 6 Sep 2006 19:34:41 +0000 (14:34 -0500)]
[POWERPC] powerpc: Reduce default cacheline size to 64 bytes
Reduce default cacheline size on 64-bit powerpc from 128 bytes to 64.
This is the architected minimum. In most cases we'll still end up using
cache line information from the device tree, but defaults are used during
early boot and doing a few dcbst/icbi's too many there won't do any harm.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch allows XMON to run on the 4xx platform. Tested on
Walnut, Ebony, and Nova (440GX based) eval boards. 440EP, 440SP, and
440SPE boards should work as well. Patch is against 2.6.18-rc6.
Signed-off-by: Josh Boyer <jdub@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Make function of pm_power_off consistent with x86
Allow the pm_power_off function variable in PPC to work as an override.
This makes the function consistent with the other architectures and it
allows generic poweroff operations (like those provided in IPMI
systems) to work properly on PPC.
Signed-off-by: Corey Minyard <minyard@acm.org> Cc: Joseph Barnett <jbarnett@motorola.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Will Schmidt [Wed, 30 Aug 2006 18:11:38 +0000 (13:11 -0500)]
[POWERPC] Emulate power5 popcntb instruction
In an attempt to make it easier for a power5 optimized app to run on a
power4 or a 970 or random earlier machine, this provides emulation of
the popcntb instruction.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 24 Aug 2006 06:54:08 +0000 (16:54 +1000)]
[POWERPC] Split out vpa unregister logic from pseries_kexec_cpu_down_xics()
As part of the new irq code pseries_kexec_cpu_down() was split into a
xics and mpic version. The vpa unregister logic is now only done in the
xics routine, and although that's ok in practice (we don't have SPLPAR
machines with mpic), I'd rather have the two concepts stay separate.
So move the vpa unregister into pseries_kexec_cpu_down(), which gets called
by both the xics and mpic routines. This also gives us an obvious place to
put any new kexec-down logic needed in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Sachin P. Sant [Fri, 8 Sep 2006 02:29:52 +0000 (07:59 +0530)]
[POWERPC] kdump: Support kernels having 64k page size.
This is required to generate proper core files using kdump on ppc64.
Create a backup region of 64K size irrespective of the PAGE SIZE.
At present 32K was used as backup size. In the case of 64K page size,
second PT_LOAD segments starts at 32K and the first one is not page
aligned. __ioremap() (crash_dump.c) fails if pfn = 0 which is the
case for the second PT_LOAD segment. This is not an issue for 4K page
size because the the first page (32K backup) is copied to second
kernel memory and thus referencing with the second kernel pfn.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
The sys_[gs]et_robust_list() syscalls were wired up on PowerPC but
didn't work correctly because futex_atomic_cmpxchg_inatomic() wasn't
implemented. Implement it, based on __cmpxchg_u32().
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge branch 'audit.b29' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current
* 'audit.b29' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] sparc64 audit syscall classes hookup
[PATCH] syscall class hookup for all normal targets
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4608c): Fix I2C dependencies for saa7146 modules
V4L/DVB (4608b): i2c deps fix on DVB
V4L/DVB (4605): Fixes an issue with V4L1 and make headers-install
V4L/DVB (4520): Fix an error when loading bttv driver on PV M4900.
V4L/DVB (4511): Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to fix UHF switch functionality
V4L/DVB (4494a): Fix compilation when V4L1 support is not present
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6:
sh64: Add a sane pm_power_off implementation.
sh64: Use generic BUG_ON()/WARN_ON().
sh64: Trivial build fixes.
sh64: Drop deprecated ISA tuning for legacy toolchains.
* git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Fix a bad pointer dereference in the quota statvfs handling.
[XFS] Fix xfs_splice_write() so appended data gets to disk.
[XFS] Fix ABBA deadlock between i_mutex and iolock. Avoid calling
[XFS] Prevent free space oversubscription and xfssyncd looping.
USB: Fix unload oops and memory leak in yealink driver
This patch fixes a memory leak and a kernel oops when trying to unload
the driver, due to an unbalanced cleanup.
Thanks Ivar Jensen for spotting my mistake.
Al Viro [Tue, 12 Sep 2006 06:59:45 +0000 (02:59 -0400)]
[PATCH] sparc64 audit syscall classes hookup
... that should do it for all targets; the only remaining issues are
mips (currently treated as non-biarch) and handling of other OS
emulations (OSF/SunOS/Solaris/???). The latter would need to be
assigned new AUDIT_ARCH_... ABI numbers anyway...
Paul Mundt [Tue, 12 Sep 2006 05:36:46 +0000 (14:36 +0900)]
sh64: Trivial build fixes.
While we've been sorting out the toolchain fiasco, some of
the code has suffered a bit of bitrot. Building with GCC4
also brings up some more build warnings. Trivial fixes for
both issues.
Paul Mundt [Tue, 12 Sep 2006 05:21:25 +0000 (14:21 +0900)]
sh64: Drop deprecated ISA tuning for legacy toolchains.
The original sh64 toolchains required that we tune the ISA
level accordingly to not have head.S/entry.S blow up. With
current toolchains, this is no longer the case, and the
syntax magically changed as well, causing all current
toolchains to die a horrible death.
Incidentally, code generation in other parts of the kernel
is now significantly complex enough that none of the older
toolchains make it very far these days, so there's not
even any point in preserving legacy compatability via
as-option.
This fixes a long-standing issue, as noted here:
http://lkml.org/lkml/2005/1/5/223
Though at the time the current toolchains were too broken
to make adjusting the tuning worthwhile.
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
usbtouchscreen: fix ITM data reading
USB: New device ID for ftdi_sio usb serial driver
USB: Support for USB20SVGA-WH & USB20SVGA-DG
USB: hid-core.c: fix duplicate USB_DEVICE_ID_GTCO_404
Steve Grubb [Sat, 26 Aug 2006 18:06:20 +0000 (14:06 -0400)]
[PATCH] fix ppid bug in 2.6.18 kernel
Hello,
During some troubleshooting, I found that ppid was accidentally omitted from
the legacy rule section. This resulted in EINVAL for any rule with ppid sent
with AUDIT_ADD.
Signed-off-by: Steve Grubb <sgrubb@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3778/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [simtec]
[ARM] 3783/1: S3C2412: fix IRQ_EINT0 to IRQ_EINT3 handling
[ARM] 3779/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [left]
[ARM] 3777/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [regs-*.h]
[ARM] 3776/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410
[ARM] 3775/1: S3C24XX: do not add same sysdev_driver to two classes
[ARM] 3774/1: S3C24XX: SMDK2413 has two machine IDs
[ARM] 3773/1: Add the HWCAP_VFP bit for the ARM926 CPUs
[ARM] 3772/1: Fix compilation error in mach-ixp4xx/nslu2*
[ARM] 3767/1: S3C24XX: remove changelog comments from arch/arm/mach-s3c2410
[ARM] 3766/1: Fix typo in ARM _raw_read_trylock
Alan Cox [Mon, 11 Sep 2006 13:45:07 +0000 (14:45 +0100)]
[PATCH] Fix 2.6.18-rc6 IDE breakage, add missing ident needed for current VIA boards
There are two changes here. The first reverses the broken PCI_DEVICE
conversion back to the old format. The second adds a missing PCI ID so
you can actually boot 2.6.18 on 2 month old VIA motherboards (right now
only 2.6.18-mm works).
CC'd to Jeff to check the PCI ident but its a) in several distro kernels
and b) in 2.6.18-mm [twice ??]
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andres Salomon [Mon, 11 Sep 2006 12:51:05 +0000 (08:51 -0400)]
[libata] sata_mv: errata check buglet fix
Fix a buglet; the errata check below this code is assuming the value in
the sstatus variable is what was pulled out of the SCR_STATUS register.
However, the status checks in the timeout loop clobber everything
but the first 4 bits of sstatus, so the errata checks are invalid.
This patch changes it to not clobber SStatus.
Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
projects / linux-2.6-omap-h63xx.git / log