Patrick McHardy [Fri, 28 Mar 2008 03:28:10 +0000 (20:28 -0700)]
[LLC]: Restrict LLC sockets to root
LLC currently allows users to inject raw frames, including IP packets
encapsulated in SNAP. While Linux doesn't handle IP over SNAP, other
systems do. Restrict LLC sockets to root similar to packet sockets.
[ Modified Patrick's patch to use CAP_NEW_RAW --DaveM ]
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 27 Mar 2008 23:08:03 +0000 (16:08 -0700)]
[ESP]: Ensure IV is in linear part of the skb to avoid BUG() due to OOB access
ESP does not account for the IV size when calling pskb_may_pull() to
ensure everything it accesses directly is within the linear part of a
potential fragment. This results in a BUG() being triggered when the
both the IPv4 and IPv6 ESP stack is fed with an skb where the first
fragment ends between the end of the esp header and the end of the IV.
This bug was found by Dirk Nehring <dnehring@gmx.net> .
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Thu, 27 Mar 2008 16:15:24 +0000 (17:15 +0100)]
rt2x00: Ignore set_state(STATE_SLEEP) failure
Some hardware never seem to accept the "goto sleep" command, since the legacy
drivers don't have suspend and resume handlers the entire code for it was
basically a educated guess (based on the "enable radio" code).
This patch will only print a warning when the "goto sleep" command fails, and
just continues as usual. Perhaps that means the device will not reach a sleep
state and consumes more power then it should, but it is equally possible it
simply needs some seconds longer to sleep. Anyway, by making the command
non-fatal it will not block the rest of the suspend procedure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Tue, 4 Mar 2008 22:58:59 +0000 (14:58 -0800)]
drivers/net/wireless/iwlwifi/iwl-4965.c: correct use of ! and &
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Signed-off-by: Julia Lawall <julia@diku.dk> Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: Guy Cohen <guy.cohen@intel.com> Cc: Reinette Chatre <reinette.chatre@intel.com> Cc: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 19 Mar 2008 14:24:21 +0000 (15:24 +0100)]
libertas: fix spinlock recursion bug
This fixes a bug detected by CONFIG_DEBUG_SPINLOCK:
if_cs_get_int_status() is only called from lbs_thread(), via
priv->hw_get_int_status. However, lbs_thread() has already taken the
priv->driver_lock. So it's a fault to take the same lock again here.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Herbert Xu [Wed, 26 Mar 2008 23:51:09 +0000 (16:51 -0700)]
[IPSEC]: Fix BEET output
The IPv6 BEET output function is incorrectly including the inner
header in the payload to be protected. This causes a crash as
the packet doesn't actually have that many bytes for a second
header.
The IPv4 BEET output on the other hand is broken when it comes
to handling an inner IPv6 header since it always assumes an
inner IPv4 header.
This patch fixes both by making sure that neither BEET output
function touches the inner header at all. All access is now
done through the protocol-independent cb structure. Two new
attributes are added to make this work, the IP header length
and the IPv4 option length. They're filled in by the inner
mode's output function.
Thanks to Joakim Koskela for finding this problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 26 Mar 2008 09:27:09 +0000 (02:27 -0700)]
[ICMP]: Dst entry leak in icmp_send host re-lookup code (v2).
Commit 8b7817f3a959ed99d7443afc12f78a7e1fcc2063 ([IPSEC]: Add ICMP host
relookup support) introduced some dst leaks on error paths: the rt
pointer can be forgotten to be put. Fix it bu going to a proper label.
Found after net namespace's lo refused to unregister :) Many thanks to
Den for valuable help during debugging.
Herbert pointed out, that xfrm_lookup() will put the rtable in case
of error itself, so the first goto fix is redundant.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 09:12:11 +0000 (02:12 -0700)]
[NET]: Fix multicast device ioctl checks
SIOCADDMULTI/SIOCDELMULTI check whether the driver has a set_multicast_list
method to determine whether it supports multicast. Drivers implementing
secondary unicast support use set_rx_mode however.
Check for both dev->set_multicast_mode and dev->set_rx_mode to determine
multicast capabilities.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 07:16:29 +0000 (00:16 -0700)]
[UML]: uml-net: don't set IFF_ALLMULTI in set_multicast_list
IFF_ALLMULTI is an indication from the network stack to the driver
to disable multicast filters, drivers should never set it directly.
Since the UML networking device doesn't have any filtering capabilites,
it doesn't the set_multicast_list function at all, it is kept so userspace
can still issue SIOCADDMULTI/SIOCDELMULTI ioctls however.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 07:15:17 +0000 (00:15 -0700)]
[VLAN]: Don't copy ALLMULTI/PROMISC flags from underlying device
Changing these flags requires to use dev_set_allmulti/dev_set_promiscuity
or dev_change_flags. Setting it directly causes two unwanted effects:
- the next dev_change_flags call will notice a difference between
dev->gflags and the actual flags, enable promisc/allmulti
mode and incorrectly update dev->gflags
- this keeps the underlying device in promisc/allmulti mode until
the VLAN device is deleted
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Tue, 25 Mar 2008 17:04:46 +0000 (18:04 +0100)]
b44: Truncate PHY address
Some ROMs on embedded devices store incorrect values for
the PHY address of the ethernet device.
It looks like the number is sign-extended.
Truncate the value by applying the PHY-address mask to it.
The patch was tested on a bcm47xx embedded system (where the bug
triggers) and a bcm4400 PCI card.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jussi Kivilinna [Sun, 23 Mar 2008 10:45:44 +0000 (12:45 +0200)]
rndis_host: fix oops when query for OID_GEN_PHYSICAL_MEDIUM fails
When query for OID_GEN_PHYSICAL_MEDIUM fails, uninitialized pointer
'phym' is being accessed in generic_rndis_bind(), resulting OOPS.
Patch fixes phym to be initialized and setup correctly when
rndis_query() for physical medium fails.
Bug was introduced by following commit:
commit 039ee17d1baabaa21783a0d5ab3e8c6d8c794bdf
Author: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Date: Sun Jan 27 23:34:33 2008 +0200
Reported-by: Dmitri Monakhov <dmonakhov@openvz.org> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The problem is that reg_lock is used with plain spin_lock() in
drivers/net/cxgb3/sge.c but is used with spin_lock_irqsave() in
drivers/net/cxgb3/cxgb3_offload.c. This is technically a false
positive, since the uses in sge.c are only in the initialization and
cleanup paths and cannot overlap with any use in interrupt context.
The best fix is probably just to use spin_lock_irq() with reg_lock in
sge.c. Even though it's not strictly required for correctness, it
avoids triggering lockdep and the extra overhead of disabling
interrupts is not important at all in the initialization and cleanup
slow paths.
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alexandr Smirnov [Tue, 18 Mar 2008 21:37:24 +0000 (00:37 +0300)]
Marvell PHY m88e1111 driver fix
Marvell PHY m88e1111 (not sure about other models, but think they too)
works in two modes: fiber and copper. In Marvell PHY driver (that we
have in current community kernels) code supported only copper mode,
and this is not configurable, bits for copper mode are simply written
in registers during PHY initialization.
This patch adds support for both modes.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dhananjay Phadke [Tue, 18 Mar 2008 02:59:50 +0000 (19:59 -0700)]
netxen: remove low level tx lock
o eliminate tx lock in netxen adapter struct, instead pound on netdev
tx lock appropriately.
o remove old "concurrent transmit" code that unnecessarily drops and
reacquires tx lock in hard_xmit_frame(), this is already serialized
the netdev xmit lock.
o reduce scope of tx lock in tx cleanup. tx cleanup operates on
different section of the ring than transmitting cpus and is
guarded by producer and consumer indices. This fixes a race
caused by rx softirq preemption on realtime kernels.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Tested-by: Vernon Mauery <mauery@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dhananjay Phadke [Tue, 18 Mar 2008 02:59:49 +0000 (19:59 -0700)]
netxen: napi and irq cleanup
o separate and simpler irq handler for msi interrupts, avoids few checks
than legacy mode.
o avoid redudant tx_has_work() and rx_has_work() checks in interrupt
and napi, which can uncork irq based on racy (lockless) access to tx
and rx ring indices. If we get interrupt, there's sufficient reason to
schedule napi.
o replenish rx ring more often, remove self-imposed threshold rcv_free
that prevents posting rx desc to card. This improves performance in
low memory.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Tested-by: Vernon Mauery <mauery@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dhananjay Phadke [Tue, 18 Mar 2008 02:59:48 +0000 (19:59 -0700)]
netxen: improve msi support
Recent netxen firmware has new scheme of generating MSI interrupts, it
raises interrupt and blocks itself, waiting for driver to unmask. This
reduces chance of spurious interrupts.
The driver will be able to deal with older firmware as well.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Tested-by: Vernon Mauery <mauery@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bryan Wu [Mon, 17 Mar 2008 21:18:31 +0000 (14:18 -0700)]
smc91x: fix build breakage from the SMC_GET_MAC_ADDR API upgrade
Cc: Jeff Garzik <jeff@garzik.org> Cc: Deepak Saxena <dsaxena@plexity.net> Cc: Nicolas Pitre <nico@cam.org> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Libor Pechacek [Sat, 22 Mar 2008 05:29:35 +0000 (22:29 -0700)]
bonding: Fix sysfs attribute handling
For bonding interfaces any attempt to read the sysfs directory contents after
module removal results in an oops. The fix is to release sysfs attributes
for the interfaces upon module unload.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Sat, 22 Mar 2008 05:29:34 +0000 (22:29 -0700)]
bonding: fix two compiler warnings
Fix two compiler warnings that are new with recent versions of gcc
(apparently 4.2 and up). One is fixed by refactoring; this change was
supplied by Stephen Hemminger. The other was fixed by labelling the
variable as uninitialized_var() after confirming via inspection that it
cannot actually be used uninitialized.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Sat, 22 Mar 2008 05:29:33 +0000 (22:29 -0700)]
bonding: Fix locking in 802.3ad mode
The 802.3ad state machine lock can be acquired in both softirq and
not softirq context, but was not held at _bh to prevent a deadlock (which
could occur if a LACPDU arrived and was processed while the lock was
held).
Corrected this, now hold the state machine lock at _bh to prevent
deadlock.
Bug reported by Todd Fleisher <todd@fleish.org>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Michael Buesch [Sat, 22 Mar 2008 21:04:45 +0000 (22:04 +0100)]
b43: Fix DMA mapping leakage
This fixes a DMA mapping leakage in the case where we reject a DMA
buffer because of its address.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Christian Casteyde <casteyde.christian@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 21 Mar 2008 20:53:41 +0000 (13:53 -0700)]
iwlwifi: fix __devexit_p points to __devexit functions
The iwlxxxx_pci_remove functions are not needed when drivers are not
compiled as modules - they can thus be discarded at kernel link time.
This is already captured by having them as __devexit_p in the pci_driver
struct - these are supposed to be pointers to __devexit functions, but was not.
This is now fixed.
This problem was reported by Toralf Forster when testing the compilation of
2.6.25-rc6.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: Toralf Forster <toralf.foerster@gmx.de> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rick Farrington [Tue, 18 Mar 2008 21:57:49 +0000 (14:57 -0700)]
iwlwifi: mac start synchronization issue
This patch fixes a synchronization problem on the 4965 and 3945 with the
mac start callback routine. The problem is that this function exits BEFORE the
'xxx_alive_start' has completed. This can lead to a problem if a
subsequent MAC callback attempts to issue a firmware command.
Signed-off-by: Rick Farrington <rickdic@hotmail.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Masakazu Mokuno [Sat, 15 Mar 2008 20:38:29 +0000 (21:38 +0100)]
rt2x00: Add id for Corega CG-WLUSB2GPX
This adds the id for Corega CG-WLUSB2GPX.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Emelyanov [Mon, 24 Mar 2008 21:48:59 +0000 (14:48 -0700)]
[NEIGH]: Fix race between pneigh deletion and ipv6's ndisc_recv_ns (v3).
Proxy neighbors do not have any reference counting, so any caller
of pneigh_lookup (unless it's a netlink triggered add/del routine)
should _not_ perform any actions on the found proxy entry.
There's one exception from this rule - the ipv6's ndisc_recv_ns()
uses found entry to check the flags for NTF_ROUTER.
This creates a race between the ndisc and pneigh_delete - after
the pneigh is returned to the caller, the nd_tbl.lock is dropped
and the deleting procedure may proceed.
One of the fixes would be to add a reference counting, but this
problem exists for ndisc only. Besides such a patch would be too
big for -rc4.
So I propose to introduce a __pneigh_lookup() which is supposed
to be called with the lock held and use it in ndisc code to check
the flags on alive pneigh entry.
Changes from v2:
As David noticed, Exported the __pneigh_lookup() to ipv6 module.
The checkpatch generates a warning on it, since the EXPORT_SYMBOL
does not follow the symbol itself, but in this file all the
exports come at the end, so I decided no to break this harmony.
Changes from v1:
Fixed comments from YOSHIFUJI - indentation of prototype in header
and the pndisc_check_router() name - and a compilation fix, pointed
by Daniel - the is_routed was (falsely) considered as uninitialized
by gcc.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Devera [Mon, 24 Mar 2008 05:00:38 +0000 (22:00 -0700)]
sch_htb: fix "too many events" situation
HTB is event driven algorithm and part of its work is to apply
scheduled events at proper times. It tried to defend itself from
livelock by processing only limited number of events per dequeue.
Because of faster computers some users already hit this hardcoded
limit.
This patch limits processing up to 2 jiffies (why not 1 jiffie ?
because it might stop prematurely when only fraction of jiffie
remains).
Signed-off-by: Martin Devera <devik@cdi.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Evgeniy Polyakov [Mon, 24 Mar 2008 04:51:12 +0000 (21:51 -0700)]
connector: convert to single-threaded workqueue
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
We don't need one cqueue thread for each CPU. cqueue is used for
receiving userspace datagrams, which are very rare and thus will
happily live with a single queue.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 23 Mar 2008 10:35:12 +0000 (03:35 -0700)]
[SUNGEM]: Fix NAPI assertion failure.
As reported by Johannes Berg:
I started getting this warning with recent kernels:
[ 773.908927] ------------[ cut here ]------------
[ 773.908954] Badness at net/core/dev.c:2204
...
If we loop more than once in gem_poll(), we'll
use more than the real budget in our gem_rx()
calls, thus eventually trigger the caller's
assertions in net_rx_action().
Subtract "work_done" from "budget" for the second
arg to gem_rx() to fix the bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Sun, 23 Mar 2008 10:07:45 +0000 (03:07 -0700)]
BNX2X: prevent ethtool from setting port type
On 10GBaseT boards setting the type to TP will cause the driver to try
to configure 1GBaseT.
Since there are currently no boards that support setting of the port
type, disable this for now.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV4] fib_trie: fix warning from rcu_assign_poinger
This gets rid of a warning caused by the test in rcu_assign_pointer.
I tried to fix rcu_assign_pointer, but that devolved into a long set
of discussions about doing it right that came to no real solution.
Since the test in rcu_assign_pointer for constant NULL would never
succeed in fib_trie, just open code instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 22 Mar 2008 22:47:05 +0000 (15:47 -0700)]
[TCP]: Let skbs grow over a page on fast peers
While testing the virtio-net driver on KVM with TSO I noticed
that TSO performance with a 1500 MTU is significantly worse
compared to the performance of non-TSO with a 16436 MTU. The
packet dump shows that most of the packets sent are smaller
than a page.
Looking at the code this actually is quite obvious as it always
stop extending the packet if it's the first packet yet to be
sent and if it's larger than the MSS. Since each extension is
bound by the page size, this means that (given a 1500 MTU) we're
very unlikely to construct packets greater than a page, provided
that the receiver and the path is fast enough so that packets can
always be sent immediately.
The fix is also quite obvious. The push calls inside the loop
is just an optimisation so that we don't end up doing all the
sending at the end of the loop. Therefore there is no specific
reason why it has to do so at MSS boundaries. For TSO, the
most natural extension of this optimisation is to do the pushing
once the skb exceeds the TSO size goal.
This is what the patch does and testing with KVM shows that the
TSO performance with a 1500 MTU easily surpasses that of a 16436
MTU and indeed the packet sizes sent are generally larger than
16436.
I don't see any obvious downsides for slower peers or connections,
but it would be prudent to test this extensively to ensure that
those cases don't regress.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from net/sctp/sm_statetable.c:50:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
In file included from net/sctp/sm_statefuns.c:62:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
...
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Oester [Fri, 21 Mar 2008 22:01:50 +0000 (15:01 -0700)]
[IPV4]: Fix null dereference in ip_defrag
Been seeing occasional panics in my testing of 2.6.25-rc in ip_defrag.
Offending line in ip_defrag is here:
net = skb->dev->nd_net
where dev is NULL. Bisected the problem down to commit ac18e7509e7df327e30d6e073a787d922eaf211d ([NETNS][FRAGS]: Make the
inet_frag_queue lookup work in namespaces).
Below patch (idea from Patrick McHardy) fixes the problem for me.
Signed-off-by: Phil Oester <kernel@linuxace.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Fri, 21 Mar 2008 00:05:13 +0000 (17:05 -0700)]
[NET] ifb: set separate lockdep classes for queue locks
[ 10.536424] =======================================================
[ 10.536424] [ INFO: possible circular locking dependency detected ]
[ 10.536424] 2.6.25-rc3-devel #3
[ 10.536424] -------------------------------------------------------
[ 10.536424] swapper/0 is trying to acquire lock:
[ 10.536424] (&dev->queue_lock){-+..}, at: [<c0299b4a>]
dev_queue_xmit+0x175/0x2f3
[ 10.536424]
[ 10.536424] but task is already holding lock:
[ 10.536424] (&p->tcfc_lock){-+..}, at: [<f8a67154>] tcf_mirred+0x20/0x178
[act_mirred]
[ 10.536424]
[ 10.536424] which lock already depends on the new lock.
lockdep warns of locking order while using ifb with sch_ingress and
act_mirred: ingress_lock, tcfc_lock, queue_lock (usually queue_lock
is at the beginning). This patch is only to tell lockdep that ifb is
a different device (e.g. from eth) and has its own pair of queue
locks. (This warning is a false-positive in common scenario of using
ifb; yet there are possible situations, when this order could be
dangerous; lockdep should warn in such a case.) (With suggestions by
David S. Miller)
Reported-and-tested-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 20 Mar 2008 23:11:27 +0000 (16:11 -0700)]
[TCP]: Fix shrinking windows with window scaling
When selecting a new window, tcp_select_window() tries not to shrink
the offered window by using the maximum of the remaining offered window
size and the newly calculated window size. The newly calculated window
size is always a multiple of the window scaling factor, the remaining
window size however might not be since it depends on rcv_wup/rcv_nxt.
This means we're effectively shrinking the window when scaling it down.
The dump below shows the problem (scaling factor 2^7):
- Window size of 557 (71296) is advertised, up to 3111907257:
IP 172.2.2.3.33000 > 172.2.2.2.33000: . ack 3111835961 win 557 <...>
- New window size of 514 (65792) is advertised, up to 3111907217, 40 bytes
below the last end:
If the sender uses up the entire window before it is shrunk, this can have
chaotic effects on the connection. When sending ACKs, tcp_acceptable_seq()
will notice that the window has been shrunk since tcp_wnd_end() is before
tp->snd_nxt, which makes it choose tcp_wnd_end() as sequence number.
This will fail the receivers checks in tcp_sequence() however since it
is before it's tp->rcv_wup, making it respond with a dupack.
If both sides are in this condition, this leads to a constant flood of
ACKs until the connection times out.
Make sure the window is never shrunk by aligning the remaining window to
the window scaling factor.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
zap_completion_queue() retrieves skbs from completion_queue where they have
zero skb->users counter. Before dev_kfree_skb_any() it should be non-zero
yet, so it's increased now.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Checconi [Thu, 20 Mar 2008 22:54:58 +0000 (15:54 -0700)]
bridge: use time_before() in br_fdb_cleanup()
In br_fdb_cleanup() next_timer and this_timer are in jiffies, so they
should be compared using the time_after() macro.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it> Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Thu, 20 Mar 2008 22:39:41 +0000 (15:39 -0700)]
audit: netlink socket can be auto-bound to pid other than current->pid (v2)
From: Pavel Emelyanov <xemul@openvz.org>
This patch is based on the one from Thomas.
The kauditd_thread() calls the netlink_unicast() and passes
the audit_pid to it. The audit_pid, in turn, is received from
the user space and the tool (I've checked the audit v1.6.9)
uses getpid() to pass one in the kernel. Besides, this tool
doesn't bind the netlink socket to this id, but simply creates
it allowing the kernel to auto-bind one.
That's the preamble.
The problem is that netlink_autobind() _does_not_ guarantees
that the socket will be auto-bound to the current pid. Instead
it uses the current pid as a hint to start looking for a free
id. So, in case of conflict, the audit messages can be sent
to a wrong socket. This can happen (it's unlikely, but can be)
in case some task opens more than one netlink sockets and then
the audit one starts - in this case the audit's pid can be busy
and its socket will be bound to another id.
The proposal is to introduce an audit_nlk_pid in audit subsys,
that will point to the netlink socket to send packets to. It
will most often be equal to audit_pid. The socket id can be
got from the skb's netlink CB right in the audit_receive_msg.
The audit_nlk_pid reset to 0 is not required, since all the
decisions are taken based on audit_pid value only.
Later, if the audit tools will bind the socket themselves, the
kernel will have to provide a way to setup the audit_nlk_pid
as well.
A good side effect of this patch is that audit_pid can later
be converted to struct pid, as it is not longer safe to use
pid_t-s in the presence of pid namespaces. But audit code still
uses the tgid from task_struct in the audit_signal_info and in
the audit_filter_syscall.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 20 Mar 2008 22:17:14 +0000 (15:17 -0700)]
[SCTP]: Fix a race between module load and protosw access
There is a race is SCTP between the loading of the module
and the access by the socket layer to the protocol functions.
In particular, a list of addresss that SCTP maintains is
not initialized prior to the registration with the protosw.
Thus it is possible for a user application to gain access
to SCTP functions before everything has been initialized.
The problem shows up as odd crashes during connection
initializtion when we try to access the SCTP address list.
The solution is to refactor how we do registration and
initialize the lists prior to registering with the protosw.
Care must be taken since the address list initialization
depends on some other pieces of SCTP initialization. Also
the clean-up in case of failure now also needs to be refactored.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Acked-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If a rule using ipt_recent is created with a hit count greater than
ip_pkt_list_tot, the rule will never match as it cannot keep track
of enough timestamps. This patch makes ipt_recent refuse to create such
rules.
With ip_pkt_list_tot's default value of 20, the following can be used
to reproduce the problem.
nc -u -l 0.0.0.0 1234 &
for i in `seq 1 100`; do echo $i | nc -w 1 -u 127.0.0.1 1234; done
This limits it to 20 packets:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 20 --name test --rsource -j DROP
While this is unlimited:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 21 --name test --rsource -j DROP
With the patch the second rule-set will throw an EINVAL.
Reported-by: Sean Kennedy <skennedy@vcn.com> Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 17 Mar 2008 16:52:24 +0000 (09:52 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Add Marvell 6121 SATA support
pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
ahci: implement skip_host_reset parameter
ahci: request all PCI BARs
devres: implement pcim_iomap_regions_request_all()
libata-acpi: improve dock event handling
Tejun Heo [Tue, 11 Mar 2008 02:35:00 +0000 (11:35 +0900)]
pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
pata_ali was using qc->nbytes to determine whether a command is
data transfer type or not. As now qc->nbytes can be extended by
padding and draining buffers, these tests are not useful anymore.
Use atapi_cmd_type() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 10 Mar 2008 01:25:25 +0000 (10:25 +0900)]
ahci: implement skip_host_reset parameter
Under certain circumstances (SSP turned off by the BIOS) and for
debugging purposes, skipping global controller reset is helpful. Add
a kernel parameter for it.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 11 Mar 2008 10:52:31 +0000 (19:52 +0900)]
ahci: request all PCI BARs
ahci is often implemented with accompanying SFF compatible interface
and legacy IDE driver may attach to the legacy IO ports when the
controller is already claimed by ahci and vice-versa. This patch
makes ahci use pcim_iomap_regions_request_all() so that all IO regions
are claimed on attach.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some drivers need to reserve all PCI BARs to prevent other drivers
misusing unoccupied BARs. pcim_iomap_regions_request_all() requests
all BARs and iomap specified BARs.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
ucc_geth: use correct thread number for 10/100Mbps link
Use thread number of 1 for 10/100Mbps link instead of 4.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
projects / linux-2.6-omap-h63xx.git / log