Matt Carlson [Sat, 22 Nov 2008 01:18:59 +0000 (17:18 -0800)]
tg3: Enable GPHY APD on select devices
GPHY Autopowerdown (APD) is a way to save power when energy is not
detected on the wire. At the moment, only the 5784 and 5761 are
capable of enabling this mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Sat, 22 Nov 2008 01:18:16 +0000 (17:18 -0800)]
tg3: Prevent corruption at 10 / 100Mbps w CLKREQ
This patch disables CLKREQ at 10Mbps and 100Mbps to workaround a TX BD
corruption issue. This problem only affects the 5784 and 5761 (and
57780 AX) ASIC revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Sat, 22 Nov 2008 01:17:04 +0000 (17:17 -0800)]
tg3: Qualify use of tp->pcix_cap
This patch makes sure the device is a PCIX device before attempting to
use the pcix_cap device structure member. This is prep work for the
following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Sat, 22 Nov 2008 01:16:16 +0000 (17:16 -0800)]
tg3: Use NET_IP_ALIGN
This patch replaces hardcoded 2's with the NET_IP_ALIGN constant or
TG3_RAW_IP_ALIGN where appropriate. Some platforms can redefine the
NET_IP_ALIGN definition to zero if unaligned DMA transfers cost more
than the IP header alignment gains. This patch represents a
performance improvement when using the 5701 on these platforms.
The copy path can be avoided.
TG3_RAW_IP_ALIGN is used in cases where we always want to align the
IP header on dword boundaries.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 01:02:41 +0000 (17:02 -0800)]
e1000e: check return code from NVM accesses and fix bank detection
Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.
For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set). If invalid, it would have defaulted to the
possibly invalid bank 0. Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.
[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 01:01:35 +0000 (17:01 -0800)]
e1000e: fix incorrect link status when switch module pulled
On 82571 with SerDes, the true link state is not always correct when read
from the STATUS register; use existing e1000_has_link() function instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 01:00:22 +0000 (17:00 -0800)]
e1000e: store EEPROM version number to prevent unnecessary NVM reads
Rather than reading the NVM to get the EEPROM version number everytime the
ethool get_drvinfo function is called, read it once during probe and save
it for future reference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:59:54 +0000 (16:59 -0800)]
e1000e: cosmetic newline in debug message
Add missing newline from debug message.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:57:36 +0000 (16:57 -0800)]
e1000e: sync change flow control variables with ixgbe
Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:54:43 +0000 (16:54 -0800)]
e1000e: link up/down messages must follow a specific format
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:53:51 +0000 (16:53 -0800)]
e1000e: ESB2 config after link up
On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this. To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split. New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:51:33 +0000 (16:51 -0800)]
e1000e: check return of pci_save_state
Check return of pci_save_state and error out accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:51:06 +0000 (16:51 -0800)]
e1000e: update comments listing supported parts for each MAC family
Some branding strings (displayed via lspci) are missing from the comments in
various family-specific files in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:50:34 +0000 (16:50 -0800)]
e1000e: 82571 check for link fix on 82571 serdes
Check for link test does not work properly for 82571 parts in a blade
environment with an unterminated serdes link partner. Make the test more
robust by checking the invalid bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 22 Nov 2008 00:49:53 +0000 (16:49 -0800)]
e1000e: commit speed/duplex changes for m88 PHY
Follow the convention used elsewhere in e1000e to 'commit' PHY changes
instead of directly writing to the PHY CTRL register to reset it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 22 Nov 2008 00:49:10 +0000 (16:49 -0800)]
e1000e: disable correctable errors for quad ports while going to D3
There has been an issue seen with the pci-e quad port adapters that will
cause them to generate a pci-e correctable error on some system while
transitioning to D3.
Since no action is needed on this correctable error the simplest solution
is to mask off the reporting of correctable errors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Sat, 22 Nov 2008 00:36:22 +0000 (16:36 -0800)]
netdevice pc300: Add the reason about PC300 BROKEN in Kconfig
When compile test my previous patch, I found PC300 driver was broken.
And there is no explanation about the broken.
Add the reason about why change this driver to broken in Kconfig.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Sat, 22 Nov 2008 00:34:18 +0000 (16:34 -0800)]
netdevice hdlc: Convert directly reference of netdev->priv
For killing directly reference of netdev->priv, use netdev->ml_priv to replace it.
Because the private pvc data comes from add_pvc() and can't be allocated in
alloc_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Rami Rosen [Wed, 19 Nov 2008 07:37:43 +0000 (09:37 +0200)]
wireless: missing include in lib80211.h
This patch adds #include <linux/timer.h> in lib80211.h to avoid
these compilation erros.
> In file included from /work/src/wireless-testing/net/wireless/lib80211.c:24:
> /work/src/wireless-testing/include/net/lib80211.h:113: error: field
> 'crypt_deinit_timer' has incomplete type
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_info_init':
> /work/src/wireless-testing/net/wireless/lib80211.c:83: error: implicit
> declaration of function 'setup_timer'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_info_free':
> /work/src/wireless-testing/net/wireless/lib80211.c:95: error: implicit
> declaration of function 'del_timer_sync'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_deinit_handler':
> /work/src/wireless-testing/net/wireless/lib80211.c:157: error:
> implicit declaration of function 'add_timer'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_delayed_deinit':
> /work/src/wireless-testing/net/wireless/lib80211.c:182: error:
> implicit declaration of function 'timer_pending'
> make[3]: *** [net/wireless/lib80211.o] Error 1
> make[2]: *** [net/wireless] Error 2
> make[1]: *** [net] Error 2
> make: *** [sub-make] Error 2
Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 12 Nov 2008 23:31:52 +0000 (17:31 -0600)]
rtl8187: Update file authorship in comments
Modify the file comments to reflect the current maintainers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 12 Nov 2008 23:13:09 +0000 (17:13 -0600)]
Update of MAINTAINERS for RTL8187
As noted by John Linville, the RTL818X maintainers have "moved on", and the
responsibilities for RTL8180 and RTL8187 have been split. This is the
corresponding update of MAINTAINERS.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 28 Oct 2008 13:00:54 +0000 (14:00 +0100)]
wireless: clean up sysfs code using %pM
Remove converting the MAC address to a string by a direct byte
conversion and use %pM instead, since the code is now boilerplate
use a macro to define the show functions, and also use the shorter
__ATTR_RO macro to define the attributes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 12 Nov 2008 19:51:56 +0000 (14:51 -0500)]
MAINTAINERS: claim maintenance over rtl818x drivers
Michael and Andrea have moved-on, so we shouldn't be bothering them
about these drivers anymore.
Actually, Herton Ronaldo Krzesinski, Hin-Tak Leung, and Larry Finger
have been handling the rtl8187 stuff for a while. So, I would welcome a
patch from one of them changing this to just RTL8180 and adding an
RTL8187 entry with their names...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 12 Nov 2008 19:37:11 +0000 (14:37 -0500)]
rtl8180: adapt for deprecated IEEE80211_CONF_SHORT_SLOT_TIME flag
This updates rtl8180 handling for short slot after "mac80211: fix short
slot handling". Only rtl8180_rtl8225 actually had code for handling
short slot times, so the other RF devices are untouched by this change.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old ieee80211 code only remains as a support library for the ipw2100
and ipw2200 drivers. So, move the code and rename it appropriately to
reflects it's true purpose and status.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 29 Oct 2008 15:35:05 +0000 (11:35 -0400)]
lib80211: absorb crypto bits from net/ieee80211
These bits are shared already between ipw2x00 and hostap, and could
probably be shared both more cleanly and with other drivers. This
commit simply relocates the code to lib80211 and adjusts the drivers
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 9 Nov 2008 22:40:46 +0000 (23:40 +0100)]
rt2x00: Fix race condition when using inderect registers
Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.
USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Sun, 9 Nov 2008 16:38:51 +0000 (18:38 +0200)]
mac80211_hwsim: Update documentation (AP mode enabled)
AP mode is now enabled in mac80211, so there is no need to point users
to an additional patch to enable the mode. In addition, add a pointer to
more hwsim test cases in hostap.git.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Sat, 8 Nov 2008 21:50:55 +0000 (23:50 +0200)]
mac80211: rc80211_pid eliminate sparse warnings
This patch eliminates sparse warnings in pid rate scale algorithm
'debugfs: allow access to signed values' patch hit the dead end
year ago w/o much echo so I guess there is no real need to address this
properly.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 8 Nov 2008 14:25:33 +0000 (15:25 +0100)]
rt2x00: Cleanup TX/RX entry handling
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Sat, 8 Nov 2008 03:50:42 +0000 (19:50 -0800)]
mac80211: remove more excess kernel-doc
Delete kernel-doc struct descriptions for fields that don't exist:
Warning(include/net/mac80211.h:1263): Excess struct/union/enum/typedef member 'conf_ht' description in 'ieee80211_ops'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'addr' description in 'sta_info'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'aid' description in 'sta_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: John W. Linville <linville@tuxdriver.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu, Yi [Fri, 7 Nov 2008 17:58:46 +0000 (09:58 -0800)]
iwlwifi: use Rx single frame mode (one Rx frame per RB)
The RCSR default value for single frame mode is off (a RB contains more than
one frames). But the driver assumes single frame mode apparently. This patch
enables single frame mode for the hardware. It also adds a BUG_ON to make sure
the allocated skb satisfies the hardware alignment requirement and removes
a useless check.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Fri, 7 Nov 2008 17:58:45 +0000 (09:58 -0800)]
iwlwifi: get some more information about command failure
This patch adds additional info about wrong command queue bug
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Fri, 7 Nov 2008 17:58:43 +0000 (09:58 -0800)]
iwlwifi: move iwl_print_hex_dump to iwl-debug.h
This patch moves iwl_print_hex_dump to iwl-debug.h
where it belongs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 7 Nov 2008 17:58:41 +0000 (09:58 -0800)]
iwlwifi: move spectrum measurement code to iwl-spectrum.c file
This patch moves spectrum measurement code into iwl-sepctrum.c file.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves byte count tables to tx domain removing completely
ambivalent shared data. Changes handling of allocation
byte count tables and keep warm consistent memory
Moves general tx scheduler definitions from iwl-4956-hw.h
to iwl-fh.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Fri, 7 Nov 2008 17:58:39 +0000 (09:58 -0800)]
iwlwifi: move rx queue read pointer into rxq
This patch moves rx status/read registers into
iwl_rx_queue structures. This solution is more memory
hungry but is more structured and provides needed RX/TX
separation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: update iwl-commands.h for 3 stream support
This patch updates comments and constants to support 1, 2, or 3 spatial streams
in rate_n_flags .
Signed-off-by: Daniel Halperin <daniel.c.halperin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Fri, 7 Nov 2008 17:58:37 +0000 (09:58 -0800)]
iwlwifi: don't fail power set when calibration is not done yet
This patch doesn't fail power save setting when calibration is
not done yet. The new power index is registered and will
be evaluated again anyway upon calibration completion.
This patch also eliminates WARN_ON in mac80211 hw_config during
initialization
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Fri, 7 Nov 2008 17:58:36 +0000 (09:58 -0800)]
iwlwifi: trivial fix in includes
This patch removes one FIXME: in rearranging includes
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 7 Nov 2008 17:58:35 +0000 (09:58 -0800)]
iwl3945: fix resume for ADHOC network
ieee80211_notify_mac only reconnect BSS networks. Since IBSS does
not need any auth or assoc steps we can just resume to the same
condition before suspend. This patch will reestablish the ad-hoc
network once it comes back from resume.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 7 Nov 2008 17:58:34 +0000 (09:58 -0800)]
iwlagn: fix resume for ADHOC network
ieee80211_notify_mac only reconnect BSS networks. Since IBSS does
not need any auth or assoc steps we can just resume to the same
condition before suspend. This patch will reestablish the ad-hoc
network once it comes back from resume.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43 bad rx: 00000010: 00 11 24 91 07 4d 00 06 25 ff 8f 78 00 06 25 ff
my MAC address | BSSID | AP MAC
b43 bad rx: 00000020: 8f 76 20 74 00 00 42 07 00 20 00 00 00 00 aa aa
| seq | QoS | CCMP IV | data
...
As you can see, there are 6 bogus bytes (sometimes only five) and then
the frame. I don't know why, and I don't see how to recover, so let's
just drop these frames.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 6 Nov 2008 14:18:11 +0000 (15:18 +0100)]
b43legacy: implement short slot and basic rate handling
This implements proper short slot handling and adds code to
program the hardware for the correct response rates derived
from the basic rate set for the current BSS.
(port from b43)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Fisher [Thu, 6 Nov 2008 08:51:16 +0000 (09:51 +0100)]
ipw2200: make association only if SSID is known.
'iwconfig eth1 channel 6' would trigger association to _something_,
which is wrong. Changing the channel should (and does) trigger reassociation,
but only if there is an SSID to associate with.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Mon, 3 Nov 2008 22:25:54 +0000 (00:25 +0200)]
ath5k: Fix IMR init
*On a previous patch i splitted AR5K_INT_TX to multiple different TX
interrupt flags for better handling but i forgot to unmask the new
TXDESC and TXEOL interrupts on ath5k_init and only left TXOK. However
for each queue we enable TXDESC and TXEOL interrupts, not TXOK so we don't
handle TX interrupts at all (because these interrupts remain masked on
PISR) and under load it results packet loss. Fix the problem by
unmasking TXDESC and TXEOL on ath5k_init.
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k : Display MAC/BB and RF version at startup (v2)
This patch decodes the MAC/BB version (for instance: AR5416) and the RF
part version (for instance: AR5133). It has been tested on AR5416/AR5133
which is a 2.4/5GHz 11n device. It also makes the differences between
AR5416 (PCI) and AR5418 (PCI Express). Both are named AR5416 in
the register definitions.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 3 Nov 2008 20:05:01 +0000 (21:05 +0100)]
mac80211: fix BUILD_BUG_ON() caused by misalignment on arm
On ARM alignment is done slightly different from other architectures.
struct ieee80211_tx_rate is aligned to word size, even though it only has 3
single-byte members, which triggers the BUILD_BUG_ON in
ieee80211_tx_info_clear_status
This patch marks the struct ieee80211_tx_rate as packed, so that ARM
behaves like the other architectures.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 3 Nov 2008 10:27:38 +0000 (11:27 +0100)]
ath5k: ignore the return value of ath5k_hw_noise_floor_calibration
Noise floor calibration occasionally fails on Atheros hardware.
This is not fatal and can happen if there's simply too much
noise on the air. Ignoring the calibration error is the right
thing to do here, because when the error is ignored, the hardware
will still work, whereas if the error causes the driver to bail out
of a bigger configuration function and does not configure the tx
queues or the IMR (as is the case in reset.c), the hw no longer
works properly until the next reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 1 Nov 2008 23:38:10 +0000 (00:38 +0100)]
rt2x00: Fix BUG_ON() with antenna handling
With the new configuration handling, and more specifically
splitting the configuration of the antenna from the normal
configuration steps allowed a BUG_ON() to be triggered
in the driver because the SW_DIVERSITY was send to the
driver. This fixes that by catching the value early in
rt2x00config.c and replacing it with a sensible value.
This also fixes a problem where the antenna is not being
initialized at all when the radio is enabled. Since it
no longer is part of the mac80211 configuration the
only place where rt2x00 configured it was the SW diversity
handler. Obviously this is broken for all non-diversity
hardware and breaks SW diversity due to a broken initialization.
When the radio is enabled the antenna will be configured
once as soon as the config() callback function is called.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 1 Nov 2008 23:37:25 +0000 (00:37 +0100)]
rt2x00: Block set_key() during suspend/shutdown
mac80211 will call set_key() when the device is
shutting down. When the device is unplugged the
keys will be lost automatically due to the power
loss. When the device is not plugged but the module
is only unloaded the keys can remain in the device
hardware, when the module is loaded the keys will
be cleaned up during initialization.
This should prevent the problem reported by Johannes Berg,
where unplugging the device while suspended resulted in
a NULL pointer error during set_key() which was
caused because of the CSR base address being freed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 1 Nov 2008 23:37:09 +0000 (00:37 +0100)]
rt2x00: Fix LED state handling
For every global LED state change (register/unregister,
suspend/resume) we should force the LEDS to turn off.
This makes sure that the LEDS will always be in a sane
state after the state switch.
Note that when unregister is called but the LED class
wasn't resumed yet, we shouldn't change the LED state
since we might not have access to the device (device
was unplugged while suspended).
Also remove the checks in the activity, assoc and
radio LEDS which blocked calls to brightness_set()
when the state hasn't changed. Some of those LEDS
could be enabled by themselves when something happens
in the hardware (e.g. firmware is loaded). We already
did called rt2x00leds to switch the LED off, but those
calls were blocked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky [Fri, 31 Oct 2008 21:50:12 +0000 (14:50 -0700)]
mac80211: disable BSSID filtering for mesh interfaces
Mesh interfaces are currently opened with the FIF_ALLMULTI rx filter flag set,
however there is no BSSID in mesh so BSSID filtering should be disabled by
setting the FIF_OTHER_BSS flag as well. Also explicitly call
ieee80211_configure_filter for mesh.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: Javier Cardona <javier@cozbit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kay Sievers [Thu, 30 Oct 2008 14:51:57 +0000 (15:51 +0100)]
ssb: struct device - replace bus_id with dev_name(), dev_set_name()
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
CC: Michael Buesch <mb@bu3sch.de> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Anna Neal [Mon, 20 Oct 2008 23:46:56 +0000 (16:46 -0700)]
libertas: Fine grained configuration of wake-on-lan.
Based on a patch from Shailendra Govardhan <shailen@marvell.com>.
This patch allows implementation of more specific wake-on-lan rules than those
of ethtool.
Please note that only firmware 5.110.22.p20 and above supports this feature.
This patch only implements the driver/firmware interface, not the
userspace/driver interface.
Signed-off-by: Anna Neal <anna@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Fri, 31 Oct 2008 18:13:12 +0000 (14:13 -0400)]
netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.
(Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
changelog but using dev->ml_priv. That doesn't seem appropriate
to me for this driver, so I've revamped it to use netdev_priv()
instead. -- JWL)
Reviewed-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Donald Skidmore [Fri, 21 Nov 2008 05:11:42 +0000 (21:11 -0800)]
ixgbe: add SFP+ driver support
This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1). These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.
Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.
Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 21 Nov 2008 05:10:23 +0000 (21:10 -0800)]
DCB: Add support for DCB BCN
Adds an interface to configure the Backward Congestion Notification
(BCN) feature. In a BCN capabale network, congestion notifications
from congested points out in the network can cause the end station
limit the rate of a given traffic flow.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 21 Nov 2008 05:09:23 +0000 (21:09 -0800)]
DCB: Add interface to query the state of PFC feature.
Adds a netlink interface for Data Center Bridging (DCB) to get and set
the enable state of the Priority Flow Control (PFC) feature.
Primarily, this is a way to turn off PFC in the driver while DCB
remains enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 21 Nov 2008 05:08:19 +0000 (21:08 -0800)]
DCB: Add interface to query # of TCs supported by device
Adds interface for Data Center Bridging (DCB) to query (and set if
supported) the number of traffic classes currently supported by the
device for the two (DCB) features: priority groups (PG) and priority
flow control (PFC).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 21 Nov 2008 05:05:08 +0000 (21:05 -0800)]
DCB: Add interface to query for the DCB capabilities of an device.
Adds to the netlink interface for Data Center Bridging (DCB), allowing
the DCB capabilities supported by a device to be queried.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 21 Nov 2008 04:52:10 +0000 (20:52 -0800)]
ixgbe: this patch adds support for DCB to the kernel and ixgbe driver
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel. The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to network device ops. Needed to change to directly call
the init routine since two sides share same ops. In the process
found by inspection a device ref count leak if register_netdevice failed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp> Signed-off-by: Tony Luck <tony.luck@intel.com>
projects / linux-2.6-omap-h63xx.git / log