Harald Welte [Tue, 24 Jul 2007 10:49:39 +0000 (12:49 +0200)]
[ALSA] s3c24xx-pcm: fix hw_params dma handling
Since the PCM emulation can call multiple times to hw_setup(), but we
can only once allocate/request the DMA channel, we have to handle
this gracefully.
Signed-off-by: Harald Welte <laforge@openmoko.org> Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
[ALSA] ca0106: Add analog mute controls for cards with SPI DAC
Add four mute controls for the analog output channels for cards that use
an SPI DAC, like the SB0570 SB Live! 24-bit / Audigy SE. The Wolfson DAC
doesn't support muting left/right so the controls are mono.
The chip state struct gets a 32-byte array to act as a shadow of the spi
dac registers. Only two registers are used for mute, but more would be
needed for analog gain, de-emphasis, DAC power down, phase inversion, and
other features.
Clemens Ladisch [Mon, 23 Jul 2007 15:38:44 +0000 (17:38 +0200)]
[ALSA] ymfpci: fix volume handling of the 44.1 kHz slot
The existing code for handling the 44.1 slot's volume has two problems:
the volume is not affected by the 'Wave Playback Volume' mixer control,
and the BUF441OUTVOL register, which is used to control the per-
substream volume for this slot, uses a different scale than the gain
fields of the other slots.
This patch makes the BUF441OUTVOL register a shadow of the
NATIVEDACOUTVOL register so that the Wave volume is consistent for all
substreams.
As a consequence of this, the per-substream PCM volume control gets no
longer activated for the substream using this slot. The code for
(de)activating the mixer control is moved from the open/close to the
prepare/trigger_stop callbacks so that it is able to determine the
substream's slot.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
[ALSA] ALSA sound driver for the AT73C213 DAC using Atmel SSC driver
This patch adds support for the AT73C213 DAC using the misc Atmel SSC driver in
I2S mode. The driver also requires a SPI to setup the registers and control
volume.
It has been tested with an AT32AP7000 on the ATSTK1000 development board. The
driver should also work with any Atmel device with an SSC module supported by
the Atmel SSC driver (atmel-ssc).
The atmel-ssc driver is just submitted to the Linux kernel. Please see mail
thread http://lkml.org/lkml/2007/7/16/32
Stephen Rothwell [Mon, 23 Jul 2007 10:10:07 +0000 (12:10 +0200)]
[ALSA] Fix tas_suspend/resume build warning
sound/aoa/codecs/snd-aoa-codec-tas.c:750: warning: 'tas_suspend' defined but not used
sound/aoa/codecs/snd-aoa-codec-tas.c:760: warning: 'tas_resume' defined but not used Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Linus Torvalds [Mon, 15 Oct 2007 23:08:50 +0000 (16:08 -0700)]
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
Linus Torvalds [Mon, 15 Oct 2007 23:07:40 +0000 (16:07 -0700)]
Merge branch 'locks' of git://linux-nfs.org/~bfields/linux
* 'locks' of git://linux-nfs.org/~bfields/linux:
nfsd: remove IS_ISMNDLCK macro
Rework /proc/locks via seq_files and seq_list helpers
fs/locks.c: use list_for_each_entry() instead of list_for_each()
NFS: clean up explicit check for mandatory locks
AFS: clean up explicit check for mandatory locks
9PFS: clean up explicit check for mandatory locks
GFS2: clean up explicit check for mandatory locks
Cleanup macros for distinguishing mandatory locks
Documentation: move locks.txt in filesystems/
locks: add warning about mandatory locking races
Documentation: move mandatory locking documentation to filesystems/
locks: Fix potential OOPS in generic_setlease()
Use list_first_entry in locks_wake_up_blocks
locks: fix flock_lock_file() comment
Memory shortage can result in inconsistent flocks state
locks: kill redundant local variable
locks: reverse order of posix_locks_conflict() arguments
Linus Torvalds [Mon, 15 Oct 2007 21:06:58 +0000 (14:06 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IPV6]: Consolidate the ip6_pol_route_(input|output) pair
[TCP]: Make snd_cwnd_cnt 32-bit
[TCP]: Update the /proc/net/tcp documentation
[NETNS]: Don't panic on creating the namespace's loopback
[NEIGH]: Ensure that pneigh_lookup is protected with RTNL
[INET]: kmalloc+memset -> kzalloc in frag_alloc_queue
[ISDN]: Fix compile with CONFIG_ISDN_X25 disabled.
[IPV6]: Replace sk_buff ** with sk_buff * in input handlers
[SELINUX]: Update for netfilter ->hook() arg changes.
[INET]: Consolidate the xxx_put
[INET]: Small cleanup for xxx_put after evictor consolidation
[INET]: Consolidate the xxx_evictor
[INET]: Consolidate the xxx_frag_destroy
[INET]: Consolidate xxx_the secret_rebuild
[INET]: Consolidate the xxx_frag_kill
[INET]: Collect common frag sysctl variables together
[INET]: Collect frag queues management objects together
[INET]: Move common fields from frag_queues in one place.
[TG3]: Fix performance regression on 5705.
[ISDN]: Remove local copy of device name to make sure renames work.
...
Linus Torvalds [Mon, 15 Oct 2007 20:41:39 +0000 (13:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: use full RCU API
Input: remove tsdev interface
Input: add support for Blackfin BF54x Keypad controller
Input: appletouch - another fix for idle reset logic
HWMON: hdaps - switch to using input-polldev
Input: add support for SEGA Dreamcast keyboard
Input: omap-keyboard - don't pretend we support changing keymap
Input: lifebook - fix X and Y axis range
Input: usbtouchscreen - add support for GeneralTouch devices
Input: fix open count handling in input interfaces
Input: keyboard - add CapsShift lock
Input: adbhid - produce all CapsLock key events
Input: ALPS - add signature for ThinkPad R61
Input: jornada720_kbd - send MSC_SCAN events
Input: add support for the HP Jornada 7xx (710/720/728) touchscreen
Input: add support for HP Jornada 7xx onboard keyboard
Input: add support for HP Jornada onboard keyboard (HP6XX)
Input: ucb1400_ts - use schedule_timeout_uninterruptible
Input: xpad - fix dependancy on LEDS class
Input: auto-select INPUT for MAC_EMUMOUSEBTN option
...
Resolved conflicts manually in drivers/hwmon/applesmc.c: converting from
a class device to a device and converting to use input-polldev created a
few apparently trivial clashes..
Linus Torvalds [Mon, 15 Oct 2007 20:31:14 +0000 (13:31 -0700)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_pcmcia: Add additional id string (corsair, 1GB)
libata: prevent devices with blank model names from being DMA blacklisted
ata_piix: SATA 2port controller port map fix
pata_cs5536: ATA driver for Geode companion chip
libata: add ST9160821AS / 3.CCD to NCQ blacklist
libata: fix revalidation issuing after configuration commands
[libata] sata_nv: add SW NCQ support for MCP51/MCP55/MCP61
[libata] pata_sil680: Add MMIO support
Linus Torvalds [Mon, 15 Oct 2007 20:30:35 +0000 (13:30 -0700)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (35 commits)
xen-netfront: rearrange netfront structure to separate tx and rx
netdev: convert non-obvious instances to use ARRAY_SIZE()
ucc_geth: Fix build break introduced by commit 09f75cd7bf13720738e6a196cc0107ce9a5bd5a0
gianfar: Fix regression caused by new napi interface
gianfar: Cleanup compile warning caused by 0795af57
gianfar: Fix compile regression caused by bea3348e
add new prom.h for AU1x00
update AU1000 get_ethernet_addr()
MIPSsim: General cleanup
Jazzsonic: Fix warning about unused variable.
Remove msic_dcr_read() in axon_msi.c
Use dcr_host_t.base in dcr_unmap()
Add dcr_host_t.base in dcr_read()/dcr_write()
Use dcr_host_t.base in ibm_emac_mal
Update ibm_newemac to use dcr_host_t.base
tehuti: possible leak in bdx_probe
TC35815: Fix build
SAA9730: Fix build
AR7 ethernet
myri10ge: update driver version to 1.3.2-1.287
...
xen-netfront: rearrange netfront structure to separate tx and rx
Keep tx and rx elements separate on different cachelines to prevent
bouncing.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Atari keyboard: incorporate additional review comments:
o Kill reference to source file name
o Return error value from input_register_device() instead of -ENOMEM
Ilpo Järvinen [Mon, 15 Oct 2007 19:59:43 +0000 (12:59 -0700)]
[TCP]: Make snd_cwnd_cnt 32-bit
Very little point of having 32-bit snd_cnwd if this is not
32-bit as well, as a number of snd_cwnd incrementation formulas
assume that snd_cwnd_cnt can be at least as large as snd_cwnd.
Whether 32-bit is useful was discussed when e0ef57cc56c3c96
was made:
http://marc.info/?l=linux-netdev&m=117218144409825&w=2
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Mon, 15 Oct 2007 19:55:33 +0000 (12:55 -0700)]
[NETNS]: Don't panic on creating the namespace's loopback
When the loopback device is failed to initialize inside the new
namespaces, panic() is called. Do not do it when the namespace
in question is not the init_net.
Plus cleanup the error path a bit.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 15 Oct 2007 19:55:20 +0000 (12:55 -0700)]
Reinstate lost flush_ioremap_region() fix to pxa2xx-flash driver
Commit 90833fdab89da02fc0276224167f0a42e5176f41 ("[ARM] 4554/1: replace
consistent_sync() with flush_ioremap_region()") introduced a new
"flush_ioremap_region()" function to be used by the MTD mainstone-flash
and lubbock-flash drivers to fix a regression from around 2.6.18.
Those drivers were independently merged into a single driver by Todd
Poynor in commit e644f7d6289456657996df4192de76c5d0a9f9c7 ("[MTD] MAPS:
Merge Lubbock and Mainstone drivers into common PXA2xx driver")
Later, those two commits were merged into the main MTD tree by commit b160292cc216a50fd0cd386b0bda2cd48352c73b ("Merge Linux 2.6.23") by David
Woodhouse, but in that merge, the fix to use flush_iomap_region() got
lost (as it was to files that now no longer existed).
This reinstates the fix in the new driver.
Noticed-by: Russell King <rmk@arm.linux.org.uk> Tested-and-acked-by: Nicolas Pitre <nico@cam.org> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Jared Hulbert <jaredeh@gmail.com> Cc: Todd Poynor <tpoynor@mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Emelyanov [Mon, 15 Oct 2007 19:54:15 +0000 (12:54 -0700)]
[NEIGH]: Ensure that pneigh_lookup is protected with RTNL
The pnigh_lookup is used to lookup proxy entries and to
create them in case lookup failed.
However, the "creation" code does not perform the re-lookup
after GFP_KERNEL allocation. This is done because the code
is expected to be protected with the RTNL lock, so add the
assertion (mainly to address future questions from new network
developers like me :) ).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Mon, 15 Oct 2007 19:52:20 +0000 (12:52 -0700)]
[ISDN]: Fix compile with CONFIG_ISDN_X25 disabled.
On Mon, Oct 15, 2007 at 06:44:56PM +0400, Denis V. Lunev wrote:
Compilation fix. The problem appears after 7c076d1de869256848dacb8de0050a3a390f95df by Karsten Keil <kkeil@suse.de>
Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 15 Oct 2007 19:50:28 +0000 (12:50 -0700)]
[IPV6]: Replace sk_buff ** with sk_buff * in input handlers
With all the users of the double pointers removed from the IPv6 input path,
this patch converts all occurances of sk_buff ** to sk_buff * in IPv6 input
handlers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 15 Oct 2007 19:46:16 +0000 (12:46 -0700)]
scsi/gdth: fix crash in gdth_timeout if no gdth controllers found
If the gdth module is loaded (or compiled in), the gdth_timeout function
gets started even if no actual gdth controllers are found b the probing.
That ends up not only being unnecessary, but also causes a crash due to
the function blindly just trying to pick the first entry off the
"gdth_instances" list, and accessing it - which obviously doesn't work
if the list is empty!
Andrew Paprocki [Mon, 15 Oct 2007 19:43:12 +0000 (15:43 -0400)]
libata: prevent devices with blank model names from being DMA blacklisted
The strn_pattern_cmp routine does not handle a blank name parameter
properly. The only patterns which should match a blank name are "*"
and an explicit "". If the function is passed a blank name in current
code, it will always match against the patt parameter. The bug manifests
itself as the device with the empty model name always matching the first
device in the DMA blacklist, forcing it to revert to PIO mode.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a driver for the ATA controller on the Geode CS5536 companion
chip. The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct. This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly. Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Pavel Emelyanov [Mon, 15 Oct 2007 09:41:09 +0000 (02:41 -0700)]
[INET]: Small cleanup for xxx_put after evictor consolidation
After the evictor code is consolidated there is no need in
passing the extra pointer to the xxx_put() functions.
The only place when it made sense was the evictor code itself.
Maybe this change must got with the previous (or with the
next) patch, but I try to make them shorter as much as
possible to simplify the review (but they are still large
anyway), so this change goes in a separate patch.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Mon, 15 Oct 2007 09:39:14 +0000 (02:39 -0700)]
[INET]: Consolidate the xxx_frag_destroy
To make in possible we need to know the exact frag queue
size for inet_frags->mem management and two callbacks:
* to destoy the skb (optional, used in conntracks only)
* to free the queue itself (mandatory, but later I plan to
move the allocation and the destruction of frag_queues
into the common place, so this callback will most likely
be optional too).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Mon, 15 Oct 2007 09:33:45 +0000 (02:33 -0700)]
[INET]: Collect common frag sysctl variables together
Some sysctl variables are used to tune the frag queues
management and it will be useful to work with them in
a common way in the future, so move them into one
structure, moreover they are the same for all the frag
management codes.
I don't place them in the existing inet_frags object,
introduced in the previous patch for two reasons:
1. to keep them in the __read_mostly section;
2. not to export the whole inet_frags objects outside.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Mon, 15 Oct 2007 09:31:52 +0000 (02:31 -0700)]
[INET]: Collect frag queues management objects together
There are some objects that are common in all the places
which are used to keep track of frag queues, they are:
* hash table
* LRU list
* rw lock
* rnd number for hash function
* the number of queues
* the amount of memory occupied by queues
* secret timer
Move all this stuff into one structure (struct inet_frags)
to make it possible use them uniformly in the future. Like
with the previous patch this mostly consists of hunks like
To address the issue with exporting the number of queues and
the amount of memory occupied by queues outside the .c file
they are declared in, I introduce a couple of helpers.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
In making that change, the PCI latency timer and cache line size
registers were not restored after chip reset. On the 5705, the
latency timer gets reset to 0 during chip reset and this causes
very poor performance.
Update version to 3.84.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Mon, 15 Oct 2007 08:48:39 +0000 (01:48 -0700)]
[IPV4]: Uninline netfilter okfns
Now that we don't pass double skb pointers to nf_hook_slow anymore, gcc
can generate tail calls for some of the netfilter hook okfn invocations,
so there is no need to inline the functions anymore. This caused huge
code bloat since we ended up with one inlined version and one out-of-line
version since we pass the address to nf_hook_slow.
After:
text data bss dec hex filename 89940091016524 524652 10535185 a0c111 vmlinux
-------------------------------------------------------
-3376
All cases have been verified to generate tail-calls with and without
netfilter. The okfns in ipmr and xfrm4_input still remain inline because
gcc can't generate tail-calls for them.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 15 Oct 2007 08:47:15 +0000 (01:47 -0700)]
[NET]: Avoid copying TCP packets unnecessarily
TCP packets all have writable heads, that is, even though it's cloned, it is
writable up to the end of the TCP header. This patch makes skb_checksum_help
aware of this fact by using skb_clone_writable and avoiding a copy for TCP.
I've also modified the BUG_ON tests to be unsigned. The only case where this
makes a difference is if csum_start points to a location before skb->data.
Since skb->data should always include the header where the checksum field
is (and all currently callers adhere to that), this change is safe and may
uncover bugs later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 15 Oct 2007 08:46:08 +0000 (01:46 -0700)]
[NET]: Fix csum_start update in pskb_expand_head
I got confused by the dual nature of the off variable in the
function pskb_expand_head. The csum_start offset should use
nhead instead of off which can change depending on whether we
are using offsets or pointers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Juhl [Mon, 15 Oct 2007 08:39:12 +0000 (01:39 -0700)]
[NETLINK]: Don't leak 'listeners' in netlink_kernel_create()
The Coverity checker spotted that we'll leak the storage allocated
to 'listeners' in netlink_kernel_create() when the
if (!nl_table[unit].registered)
check is false.
This patch avoids the leak.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted that we have already oops'ed if "dst" was
NULL.
Since "dst" being NULL doesn't seem to be possible at this point this
patch removes the NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Acked-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 15 Oct 2007 08:28:47 +0000 (01:28 -0700)]
[IPV6]: Make ipv6_frag_rcv return the same packet
This patch implements the same change taht was done to ip_defrag. It
makes ipv6_frag_rcv return the last packet received of a train of fragments
rather than the head of that sequence.
This allows us to get rid of the sk_buff ** argument later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 15 Oct 2007 07:53:15 +0000 (00:53 -0700)]
[NETFILTER]: Replace sk_buff ** with sk_buff *
With all the users of the double pointers removed, this patch mops up by
finally replacing all occurances of sk_buff ** in the netfilter API by
sk_buff *.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 14 Oct 2007 07:39:01 +0000 (00:39 -0700)]
[BRIDGE]: Unshare skb upon entry
Due to the special location of the bridging hook, it should never see a
shared packet anyway (certainly not with any in-kernel code). So it
makes sense to unshare the skb there if necessary as that will greatly
simplify the code below it (in particular, netfilter).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 14 Oct 2007 07:38:32 +0000 (00:38 -0700)]
[IPV4]: Change ip_defrag to return an integer
Now that ip_frag always returns the packet given to it on input, we can
change it to return an integer indicating error instead. This patch does
that and updates all its callers accordingly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 14 Oct 2007 07:38:15 +0000 (00:38 -0700)]
[IPV4]: Make ip_defrag return the same packet
This patch is a bit of a hack. However it is worth it if you consider that
this is the only reason why we have to carry around the struct sk_buff **
pointers in netfilter.
It makes ip_defrag always return the packet that was given to it on input.
It does this by cloning the packet and replacing its original contents with
the head fragment if necessary.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 14 Oct 2007 07:37:52 +0000 (00:37 -0700)]
[SKBUFF]: Add skb_morph
This patch creates a new function skb_morph that's just like skb_clone
except that it lets user provide the spare skb that will be overwritten
by the one that's to be cloned.
This will be used by IP fragment reassembly so that we get back the same
skb that went in last (rather than the head skb that we get now which
requires us to carry around double pointers all over the place).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 14 Oct 2007 07:37:30 +0000 (00:37 -0700)]
[SKBUFF]: Merge common code between copy_skb_header and skb_clone
This patch creates a new function __copy_skb_header to merge the common
code between copy_skb_header and skb_clone. Having two functions which
are largely the same is a source of wasted labour as well as confusion.
In fact the tc_verd stuff is almost certainly a bug since it's treated
differently in skb_clone compared to the callers of copy_skb_header
(skb_copy/pskb_copy/skb_copy_expand).
I've kept that difference in tact with a comment added asking for
clarification.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Wed, 10 Oct 2007 06:57:44 +0000 (15:57 +0900)]
libata: fix revalidation issuing after configuration commands
After commands which can change device configuration, EH is scheduled
to revalidate and reconfigure the device. Host link was incorrectly
used unconditionally when scheduling EH action. This resulted in
bogus revalidation request and mismatched configuration between device
and driver. Fix it.
This bug was reported by Igor Durdanovic.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Igor Durdanovic <idurdanovic@comcast.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kuan Luo [Mon, 15 Oct 2007 19:16:53 +0000 (15:16 -0400)]
[libata] sata_nv: add SW NCQ support for MCP51/MCP55/MCP61
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller. NCQ function is disable by default, you can enable it
with 'swncq=1'. NCQ will be turned off if the drive is Maxtor on
MCP51 or MCP55 rev 0xa2 platform.
[akpm@linux-foundation.org: build fix] Signed-off-by: Kuan Luo <kluo@nvidia.com> Signed-off-by: Peer Chen <pchen@nvidia.com> Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MMIO support to the pata_sil680 for taskfile IOs,
based on what the old siimage does.
I haven't bothered changing the chip setup stuff from PCI config
cycles to MMIO though (siimage does it), I don't think it matters,
I've only adapted it to use MMIO for taskfile accesses.
I've tested it on a Cell blade and it seems to work fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ucc_geth.c: In function 'ucc_geth_rx':
drivers/net/ucc_geth.c:3483: error: 'dev' undeclared (first use in this function)
drivers/net/ucc_geth.c:3483: error: (Each undeclared identifier is reported only once
drivers/net/ucc_geth.c:3483: error: for each function it appears in.)
make[2]: *** [drivers/net/ucc_geth.o] Error 1
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Michael Ellerman [Mon, 15 Oct 2007 09:34:37 +0000 (19:34 +1000)]
Use dcr_host_t.base in dcr_unmap()
With the base stored in dcr_host_t, there's no need for callers to pass
the dcr_n into dcr_unmap(). In fact this removes the possibility of them
passing the incorrect value, which would then be iounmap()'ed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Michael Ellerman [Mon, 15 Oct 2007 09:34:36 +0000 (19:34 +1000)]
Add dcr_host_t.base in dcr_read()/dcr_write()
Now that all users of dcr_read()/dcr_write() add the dcr_host_t.base, we
can save them the trouble and do it in dcr_read()/dcr_write().
As some background to why we just went through all this jiggery-pokery,
benh sayeth:
Initially the goal of the dcr_read/dcr_write routines was to operate like
mfdcr/mtdcr which take absolute DCR numbers. The reason is that on 4xx
hardware, indirect DCR access is a pain (goes through a table of
instructions) and it's useful to have the compiler resolve an absolute DCR
inline.
We decided that wasn't worth the API bastardisation since most places
where absolute DCR values are used are low level 4xx-only code which may
as well continue using mfdcr/mtdcr, while the new API is designed for
device "instances" that can exist on 4xx and Axon type platforms and may
be located at variable DCR offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Michael Ellerman [Mon, 15 Oct 2007 09:34:35 +0000 (19:34 +1000)]
Use dcr_host_t.base in ibm_emac_mal
This requires us to do a sort-of fake dcr_map(), so that base is set
properly. This will be fixed/removed when the device-tree-aware emac driver
is merged.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
CC drivers/net/tc35815.o
drivers/net/tc35815.c: In function 'tc35815_interrupt':
drivers/net/tc35815.c:1464: error: redefinition of 'lp'
drivers/net/tc35815.c:1443: error: previous definition of 'lp' was here
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
projects / linux-2.6-omap-h63xx.git / log