David Brownell [Thu, 7 Dec 2006 01:14:03 +0000 (17:14 -0800)]
ARM: OMAP: abstract debug card setup (smc, leds)
Additional cleanup for debug boards on H2/P2/H3/H4: move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices). Make H4 use that.
This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:55 +0000 (17:13 -0800)]
ARM: OMAP: omap2/gpmc updates
GPMC updates:
- bugfixes: wrong/missing flags, omitted write, wrong test
- don't map memory segments starting at zero
- improve debug messaging
- export gpmc_get_fclk_perio]d() since it's needed to calc timings
- expect gpmc_cs_set_timings() caller to have initialized sync vs async
Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kyungmin Park [Thu, 7 Dec 2006 01:13:54 +0000 (17:13 -0800)]
ARM: OMAP: 24xx pinmux updates
Add some OMAP 24xx pin mux declarations to support:
- TUSB 6010 EVM (on H4)
- All three full speed USB ports
- GPIOs used with USB0 on Apollon and H4
For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com>
General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Mon, 2 Apr 2007 19:45:50 +0000 (12:45 -0700)]
ARM: OMAP: fix OMAP1 dmtimer build warning
Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning. It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Imre Deak [Mon, 5 Mar 2007 15:34:05 +0000 (17:34 +0200)]
ARM: OMAP: add SoSSI clock (remove manual checking of SoSSI state from idle)
The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:11 +0000 (17:14 -0800)]
ARM: OMAP: MPUIO wake updates
GPIO and MPUIO wake updates:
- Hook MPUIOs into the irq wakeup framework too. This uses a platform
device to update irq enables during system sleep states, instead of
a sys_device, since the latter is no longer needed for such things.
- Also forward enable/disable irq wake requests to the relevant GPIO
controller, so the top level IRQ dispatcher can (eventually) handle
these wakeup events automatically if more than one GPIO pin needs to
be a wakeup event source.
- Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such
read-only data under the spinlock.
This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without
a 15xx I can't test such stuff.
Also this expects the top level IRQ dispatcher to properly handle requests
to enable/disable irq wake, which is currently known to be wrong: omap1
saves the flags but ignores them, omap2 doesn't even save it. (Wakeup
events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...)
So MPUIO irqs won't yet trigger system wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:10 +0000 (17:14 -0800)]
ARM: OMAP: speed up gpio irq handling
Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function. On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods. Hey, every
few instructions help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:59 +0000 (17:13 -0800)]
ARM: OMAP: gpio object shrinkage, cleanup
More GPIO/IRQ cleanup:
- compile-time removal of much useless code
* mpuio support on non-OMAP1.
* 15xx/730/24xx gpio support on 1610
* 15xx/730/16xx gpio support on 24xx
* etc
- remove all BUG() calls, which are always bad news ... replaced some
with normal fault reports for that call, others with WARN_ON(1).
- small mpuio bugfix: add missing set_type() method
Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:53 +0000 (17:13 -0800)]
ARM: OMAP: /sys/kernel/debug/omap_gpio
Add some GPIO debug support: /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.
Includes minor bugfixes: recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Thu, 7 Dec 2006 01:13:52 +0000 (17:13 -0800)]
ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Wed, 28 Mar 2007 20:09:36 +0000 (13:09 -0700)]
ARM: OMAP: partial LED fixes
Partial fix for CONFIG_LEDS breakage ... at least allow platforms
using the debug-leds support (H4 for now) to build with the generic
LED support, and default the LED that would be the timer LED to
trigger using the "heartbeat" (timer driven, rate depends on load).
Right now only H2 and P2 seem to have working LED support; this
at least makes H4 less broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Imre Deak [Tue, 6 Mar 2007 11:16:36 +0000 (03:16 -0800)]
ARM: OMAP: FB sync with N800 tree (support for dynamic SRAM allocations)
- in addition to fixed FB regions - as passed by the bootloader -
allow dynamic allocations
- do some more checking against overlapping / reserved regions
- move the FB specific parts out from sram.c to fb.c
Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 7 Dec 2006 22:01:23 +0000 (14:01 -0800)]
ARM: OMAP: Avoid updating system time for sub-jiffy interrupts
Updating system time and reprogramming timer can cause latency
issues on busy systems with lots of interrupts with constant
updating of time and reprogramming the system timer.
If a non-timer dyntick interrupt happens within a jiffy from
the last interrupt, updating time and reprogramming the timer
is unnecessary as we will get a timer interrupt soon anyways.
Tony Lindgren [Thu, 7 Dec 2006 21:57:38 +0000 (13:57 -0800)]
ARM: OMAP: Sync headers with linux-omap
This patch syncs omap specific headers with linux-omap.
Most of the changes needed because of bitrot caused by
driver changes in linux-omap tree. Integrating this
is needed for adding support for various omap drivers.
David Brownell [Thu, 7 Dec 2006 01:14:03 +0000 (17:14 -0800)]
ARM: OMAP: h4 must have blinky leds!!
This adds generic support for the "debug board" LEDs used by most of
TI's OMAP reference boards, and board-specific support for the H4.
It's derived from the not-as-generic stuff used by OMAP1 H2/H3/P2.
Those should be able to switch easily to this version, and clean up
some of the omap1-specific code.
In addition to H4 support, one key improvement is supporting not just
the "old" ARM debug LED API (with timer and idle LEDs, plus four that
can be handy for kernel debugging), but it also supports the "new"
generic LED API (most useful for usermode stuff IMO). Either or both
APIs can be enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Imre Deak [Thu, 7 Dec 2006 01:13:50 +0000 (17:13 -0800)]
ARM: OMAP: FB: add controller platform data
Add controller platform data
Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix logic error in VMI relocation processing. NOPs would always cause
a BUG_ON to fire because the != RELOCATION_NONE in the first if clause
precluding the == VMI_RELOCATION_NOP in the second clause. Make these
direct equality tests and just warn for unsupported relocation types
(which should never happen), falling back to native in that case.
NFS: Ensure PG_writeback is cleared when writeback fails
If the writebacks are cancelled via nfs_cancel_dirty_list, or due to the
memory allocation failing in nfs_flush_one/nfs_flush_multi, then we must
ensure that the PG_writeback flag is cleared.
Also ensure that we actually own the PG_writeback flag whenever we
schedule a new writeback by making nfs_set_page_writeback() return the
value of test_set_page_writeback().
The PG_writeback page flag ends up replacing the functionality of the
PG_FLUSHING nfs_page flag, so we rip that out too.
James Bottomley [Fri, 6 Apr 2007 16:14:56 +0000 (11:14 -0500)]
[SCSI] 3w-xxxx: fix oops caused by incorrect REQUEST_SENSE handling
3w-xxxx emulates a REQUEST_SENSE response by simply returning nothing.
Unfortunately, it's assuming that the REQUEST_SENSE command is
implemented with use_sg == 0, which is no longer the case. The oops
occurs because it's clearing the scatterlist in request_buffer instead
of the memory region.
This is fixed by using tw_transfer_internal() to transfer correctly to
the scatterlist.
Acked-by: adam radford <aradford@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Olaf Kirch [Fri, 13 Apr 2007 05:18:44 +0000 (01:18 -0400)]
DVB: dvb-usb-remote - fix oops when changing keymap
DVB USB remotes do not support changing keycode maps but set
input_dev->keycodesize and input_dev->keycodemax without setting
input_dev->keycode. This causes kernel oops when user tries to
look up (or change) current keymap.
While the proper fix would be to make remotes handle keymap changes
we'll just remove keycodemax and keycodesize initialization so
EVIOCGKEYCODE and EVIOCSKEYCODE will simply return -EINVAL.
David S. Miller [Fri, 13 Apr 2007 23:37:54 +0000 (16:37 -0700)]
[NETFILTER] arp_tables: Fix unaligned accesses.
There are two device string comparison loops in arp_packet_match().
The first one goes byte-by-byte but the second one tries to be
clever and cast the string to a long and compare by longs.
The device name strings in the arp table entries are not guarenteed
to be aligned enough to make this value, so just use byte-by-byte
for both cases.
Based upon a report by <drraid@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet which is being discarded because of no routes in the
forwarding path should not be counted as OutNoRoutes but as
InNoRoutes.
Additionally, on this occasion, a packet whose destinaion is
not valid should be counted as InAddrErrors separately.
Based on patch from Mitsuru Chinen <mitch@linux.vnet.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
We are using size of security context from xfrm_policy to determine
how much space to alloc skb and then putting security context from
xfrm_state into skb. Should have been using size of security context
from xfrm_state to alloc skb. Following fix does that
Signed-off-by: Joy Latten <latten@austin.ibm.com> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[VLAN]: Allow VLAN interface on top of bridge interface
When a VLAN interface is created on top of a bridge interface and
netfilter is enabled to see the bridged packets, the packets can be
corrupted when passing through the netfilter code. This is caused by the
VLAN driver not setting the 'protocol' and 'nh' members of the sk_buff
structure. In general, this is no problem as the VLAN interface is mostly
connected to a physical ethernet interface which does not use the
'protocol' and 'nh' members. For a bridge interface, however, these
members do matter.
Signed-off-by: Jerome Borsboom <j.borsboom@erasmusmc.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
While building a test kernel for the new esp driver (against
git-current), I hit this bug. Trivial fix, put the inline declaration
in the right place. :)
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
autofs_dentry_release() ends up clearing the ->dentry and ->inode members
of autofs_info before removing it from the rehash list. The list is
protected by the rehash lock in both functions, but since
autofs_dentry_release() starts tearing the autofs_info struct down before
removing it from the list, autofs_lookup_unhashed() can get a autofs_info
with a NULL dentry.
This patch moves the clearing of ->dentry and ->inode after the removal
from the rehash list.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bug in function decrementing a key of stat data item.
Offset of reiserfs keys are compared as signed values. To set key offset
to maximal possible value maximal signed value has to be used.
This bug is responsible for severe reiserfs filesystem corruption which
shows itself as warning vs-13060. reiserfsck fixes this corruption by
filesystem tree rebuilding.
Signed-off-by: Vladimir Saveliev <vs@namesys.com> Cc: <reiserfs-dev@namesys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Thu, 12 Apr 2007 06:28:44 +0000 (23:28 -0700)]
[PATCH] md: fix calculation for size of filemap_attr array in md/bitmap
If 'num_pages' were ever 1 more than a multiple of 8 (32bit platforms)
or of 16 (64 bit platforms). filemap_attr would be allocated one
'unsigned long' shorter than required. We need a round-up in there.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log