David S. Miller [Tue, 10 Jul 2007 05:40:36 +0000 (22:40 -0700)]
[SPARC64]: Do not ACK an INO if it is disabled or inprogress.
This is also a partial workaround for a bug in the LDOM firmware which
double-transmits RX inos during high load. Without this, such an
event causes the kernel to loop forever in the interrupt call chain
ACK'ing but never actually running the IRQ handler (and thus clearing
the interrupt condition in the device).
There is still a bad potential effect when double INOs occur,
not covered by this changeset. Namely, if the INO is already on
the per-cpu INO vector list, we still blindly re-insert it and
thus we can end up losing interrupts already linked in after
it.
We could deal with that by traversing the list before insertion,
but that's too expensive for this edge case.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 10 Jul 2007 05:22:44 +0000 (22:22 -0700)]
[SPARC64]: Add LDOM virtual channel driver and VIO device layer.
Virtual devices on Sun Logical Domains are built on top
of a virtual channel framework. This, with help of hypervisor
interfaces, provides a link layer protocol with basic
handshaking over which virtual device clients and servers
communicate.
Built on top of this is a VIO device protocol which has it's
own handshaking and message types. At this layer attributes
are exchanged (disk size, network device addresses, etc.)
descriptor rings are registered, and data transfers are
triggers and replied to.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/battery-2.6:
git-battery vs git-acpi
Power supply class and drivers: remove non obligatory return statements
pda_power: clean up irq, timer
MAINTAINERS: Add maintainers for power supply subsystem and drivers
Fixed up trivial conflict in drivers/w1/slaves/w1_ds2760.c manually
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
[TCP]: Verify the presence of RETRANS bit when leaving FRTO
[IPV6]: Call inet6addr_chain notifiers on link down
[NET_SCHED]: Kill CONFIG_NET_CLS_POLICE
[NET_SCHED]: act_api: qdisc internal reclassify support
[NET_SCHED]: sch_dsmark: act_api support
[NET_SCHED]: sch_atm: act_api support
[NET_SCHED]: sch_atm: Lindent
[IPV6]: MSG_ERRQUEUE messages do not pass to connected raw sockets
[IPV4]: Cleanup call to __neigh_lookup()
[NET_SCHED]: Revert "avoid transmit softirq on watchdog wakeup" optimization
[NETFILTER]: nf_conntrack: UDPLITE support
[NETFILTER]: nf_conntrack: mark protocols __read_mostly
[NETFILTER]: x_tables: add connlimit match
[NETFILTER]: Lower *tables printk severity
[NETFILTER]: nf_conntrack: Don't track locally generated special ICMP error
[NETFILTER]: nf_conntrack: Introduces nf_ct_get_tuplepr and uses it
[NETFILTER]: nf_conntrack: make l3proto->prepare() generic and renames it
[NETFILTER]: nf_conntrack: Increment error count on parsing IPv4 header
[NET]: Add ethtool support for NETIF_F_IPV6_CSUM devices.
[AF_IUCV]: Add lock when updating accept_q
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: fix a race condition bug in umount which caused a segfault
9p: re-enable mount time debug option
9p: cache meta-data when cache=loose
net/9p: set error to EREMOTEIO if trans->write returns zero
net/9p: change net/9p module name to 9pnet
9p: Reorganization of 9p file system code
Merge branch 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (37 commits)
[XFS] Fix lockdep annotations for xfs_lock_inodes
[LIB]: export radix_tree_preload()
[XFS] Fix XFS_IOC_FSBULKSTAT{,_SINGLE} & XFS_IOC_FSINUMBERS in compat mode
[XFS] Compat ioctl handler for handle operations
[XFS] Compat ioctl handler for XFS_IOC_FSGEOMETRY_V1.
[XFS] Clean up function name handling in tracing code
[XFS] Quota inode has no parent.
[XFS] Concurrent Multi-File Data Streams
[XFS] Use uninitialized_var macro to stop warning about rtx
[XFS] XFS should not be looking at filp reference counts
[XFS] Use is_power_of_2 instead of open coding checks
[XFS] Reduce shouting by removing unnecessary macros from dir2 code.
[XFS] Simplify XFS min/max macros.
[XFS] Kill off xfs_count_bits
[XFS] Cancel transactions on xfs_itruncate_start error.
[XFS] Use do_div() on 64 bit types.
[XFS] Fix remount,readonly path to flush everything correctly.
[XFS] Cleanup inode extent size hint extraction
[XFS] Prevent ENOSPC from aborting transactions that need to succeed
[XFS] Prevent deadlock when flushing inodes on unmount
...
Al Viro [Sun, 15 Jul 2007 20:37:16 +0000 (21:37 +0100)]
make i2c-acorn tristate
It depends on tristate I2C and it's trivial to make modular. The
current Kconfig allows I2C=m, I2C_ACORN=y, which doesn't work at
all; alternatives are dependency on I2C=y and making I2C_ACORN
itself a tristate. The latter is the right thing to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Al Viro [Sun, 15 Jul 2007 20:01:32 +0000 (21:01 +0100)]
icside: devm_iounmap() needs linux/io.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jeff Garzik [Sat, 14 Jul 2007 23:12:04 +0000 (19:12 -0400)]
pda_power: clean up irq, timer
Clean up pda_power interrupt handling:
Prior to this patch, the driver would pass information it needed
to the interrupt handler dev_id pointer, and then prompt forget it
ever did so, recreating that same information after a couple passes
through the timer-based state machine.
This patch removes the redundant checks by passing the
pda_power_supply[] pointer through the state machine. The current
code passed 'irq' through the state machine, as an index to recreate
the pointer, when we could more simply pass around the pointer itself.
This patch makes it easier to remove the 'irq' argument in the future,
in addition to cleaning up the driver today.
FUJITA Tomonori [Fri, 25 May 2007 15:32:58 +0000 (00:32 +0900)]
[SCSI] ibmvscsi: convert to use the data buffer accessors
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Santiago Leon <santil@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Alan Cox [Mon, 9 Jul 2007 19:00:10 +0000 (12:00 -0700)]
[SCSI] ppa: coding police and printk levels
Add printk levels
Clean up some oddities of formatting
Fix goto labels
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
drivers/scsi/aic7xxx_old.c:aic7xxx_slave_alloc() unnecessarily passes
GFP_ATOMIC (along with GFP_KERNEL) to kmalloc() from a context that is not
atomic. Remove the pointless GFP_ATOMIC.
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Doug Ledford <dledford@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
drivers/message/i2o/device.c:i2o_parm_field_get() unnecessarily passes
GFP_ATOMIC (along with GFP_KERNEL) to kmalloc() from a context that is not
atomic. Remove the pointless GFP_ATOMIC.
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adrian Bunk [Mon, 9 Jul 2007 19:00:10 +0000 (12:00 -0700)]
[SCSI] remove the dead CYBERSTORMIII_SCSI option
Not converted to the 2.6 kconfig system and no code in the tree.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[IPV6]: Call inet6addr_chain notifiers on link down
Currently if the link is brought down via ip link or ifconfig down,
the inet6addr_chain notifiers are not called even though all
the addresses are removed from the interface. This caused SCTP
to add duplicate addresses to it's list.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 15 Jul 2007 07:03:05 +0000 (00:03 -0700)]
[NET_SCHED]: Kill CONFIG_NET_CLS_POLICE
The NET_CLS_ACT option is now a full replacement for NET_CLS_POLICE,
remove the old code. The config option will be kept around to select
the equivalent NET_CLS_ACT options for a short time to allow easier
upgrades.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 15 Jul 2007 07:02:31 +0000 (00:02 -0700)]
[NET_SCHED]: act_api: qdisc internal reclassify support
The behaviour of NET_CLS_POLICE for TC_POLICE_RECLASSIFY was to return
it to the qdisc, which could handle it internally or ignore it. With
NET_CLS_ACT however, tc_classify starts over at the first classifier
and never returns it to the qdisc. This makes it impossible to support
qdisc-internal reclassification, which in turn makes it impossible to
remove the old NET_CLS_POLICE code without breaking compatibility since
we have two qdiscs (CBQ and ATM) that support this.
This patch adds a tc_classify_compat function that handles
reclassification the old way and changes CBQ and ATM to use it.
This again is of course not fully backwards compatible with the previous
NET_CLS_ACT behaviour. Unfortunately there is no way to fully maintain
compatibility *and* support qdisc internal reclassification with
NET_CLS_ACT, but this seems like the better choice over keeping the two
incompatible options around forever.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 15 Jul 2007 07:01:49 +0000 (00:01 -0700)]
[NET_SCHED]: sch_atm: act_api support
Handle act_api classification results.
The ATM scheduler behaves slightly different than other schedulers
in that it only handles policer results for successful classifications,
this behaviour is retained for the act_api case.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6]: MSG_ERRQUEUE messages do not pass to connected raw sockets
From: Dmitry Butskoy <dmitry@butskoy.name>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=8747
Problem Description:
It is related to the possibility to obtain MSG_ERRQUEUE messages from the udp
and raw sockets, both connected and unconnected.
There is a little typo in net/ipv6/icmp.c code, which prevents such messages
to be delivered to the errqueue of the correspond raw socket, when the socket
is CONNECTED. The typo is due to swap of local/remote addresses.
Consider __raw_v6_lookup() function from net/ipv6/raw.c. When a raw socket is
looked up usual way, it is something like:
sk = __raw_v6_lookup(sk, nexthdr, daddr, saddr, IP6CB(skb)->iif);
where "daddr" is a destination address of the incoming packet (IOW our local
address), "saddr" is a source address of the incoming packet (the remote end).
But when the raw socket is looked up for some icmp error report, in
net/ipv6/icmp.c:icmpv6_notify() , daddr/saddr are obtained from the echoed
fragment of the "bad" packet, i.e. "daddr" is the original destination
address of that packet, "saddr" is our local address. Hence, for
icmpv6_notify() must use "saddr, daddr" in its arguments, not "daddr, saddr"
...
Steps to reproduce:
Create some raw socket, connect it to an address, and cause some error
situation: f.e. set ttl=1 where the remote address is more than 1 hop to reach.
Set IPV6_RECVERR .
Then send something and wait for the error (f.e. poll() with POLLERR|POLLIN).
You should receive "time exceeded" icmp message (because of "ttl=1"), but the
socket do not receive it.
If you do not connect your raw socket, you will receive MSG_ERRQUEUE
successfully. (The reason is that for unconnected socket there are no actual
checks for local/remote addresses).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Sun, 15 Jul 2007 03:51:44 +0000 (20:51 -0700)]
[IPV4]: Cleanup call to __neigh_lookup()
Back in the times of Linux 2.2, negative values for the creat parameter
of __neigh_lookup() had a particular meaning, but no longer, so we
should pass 1 instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 15 Jul 2007 03:49:26 +0000 (20:49 -0700)]
[NET_SCHED]: Revert "avoid transmit softirq on watchdog wakeup" optimization
As noticed by Ranko Zivojnovic <ranko@spidernet.net>, calling qdisc_run
from the timer handler can result in deadlock:
> CPU#0
>
> qdisc_watchdog() fires and gets dev->queue_lock
> qdisc_run()...qdisc_restart()...
> -> releases dev->queue_lock and enters dev_hard_start_xmit()
>
> CPU#1
>
> tc del qdisc dev ...
> qdisc_graft()...dev_graft_qdisc()...dev_deactivate()...
> -> grabs dev->queue_lock ...
>
> qdisc_reset()...{cbq,hfsc,htb,netem,tbf}_reset()...qdisc_watchdog_cancel()...
> -> hrtimer_cancel() - waiting for the qdisc_watchdog() to exit, while still
> holding dev->queue_lock
>
> CPU#0
>
> dev_hard_start_xmit() returns ...
> -> wants to get dev->queue_lock(!)
>
> DEADLOCK!
The entire optimization is a bit questionable IMO, it moves potentially
large parts of NET_TX_SOFTIRQ work to TIMER_SOFTIRQ/HRTIMER_SOFTIRQ,
which kind of defeats the separation of them.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Ranko Zivojnovic <ranko@spidernet.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Sun, 15 Jul 2007 03:47:26 +0000 (20:47 -0700)]
[NETFILTER]: x_tables: add connlimit match
ipt_connlimit has been sitting in POM-NG for a long time.
Here is a new shiny xt_connlimit with:
* xtables'ified
* will request the layer3 module
(previously it hotdropped every packet when it was not loaded)
* fixed: there was a deadlock in case of an OOM condition
* support for any layer4 protocol (e.g. UDP/SCTP)
* using jhash, as suggested by Eric Dumazet
* ipv6 support
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: nf_conntrack: Don't track locally generated special ICMP error
The conntrack assigned to locally generated ICMP error is usually the one
assigned to the original packet which has caused the error. But if
the original packet is handled as invalid by nf_conntrack, no conntrack
is assigned to the original packet. Then nf_ct_attach() cannot assign
any conntrack to the ICMP error packet. In that case the current
nf_conntrack_icmp assigns appropriate conntrack to it. But the current
code mistakes the direction of the packet. As a result, NAT code mistakes
the address to be mangled.
To fix the bug, this changes nf_conntrack_icmp not to assign conntrack
to such ICMP error. Actually no address is necessary to be mangled
in this case.
Spotted by Jordan Russell.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: nf_conntrack: Introduces nf_ct_get_tuplepr and uses it
nf_ct_get_tuple() requires the offset to transport header and that bothers
callers such as icmp[v6] l4proto modules. This introduces new function
to simplify them.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: nf_conntrack: make l3proto->prepare() generic and renames it
The icmp[v6] l4proto modules parse headers in ICMP[v6] error to get tuple.
But they have to find the offset to transport protocol header before that.
Their processings are almost same as prepare() of l3proto modules.
This makes prepare() more generic to simplify icmp[v6] l4proto module
later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: nf_conntrack: Increment error count on parsing IPv4 header
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 15 Jul 2007 02:07:52 +0000 (19:07 -0700)]
[NET]: Add ethtool support for NETIF_F_IPV6_CSUM devices.
Add ethtool utility function to set or clear IPV6_CSUM feature flag.
Modify tg3.c and bnx2.c to use this function when doing ethtool -K
to change tx checksum.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The accept_queue of an af_iucv socket will be corrupted, if
adding and deleting of entries in this queue occurs at the
same time (connect request from one client, while accept call
is processed for another client).
Solution: add locking when updating accept_q
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Acked-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[AF_IUCV]: Avoid deadlock between iucv_path_connect and tasklet.
An iucv deadlock may occur, where one CPU is spinning on the
iucv_table_lock for iucv_tasklet_fn(), while another CPU is holding
the iucv_table_lock for an iucv_path_connect() and is waiting for
the first CPU in an smp_call_function.
Solution: replace spin_lock in iucv_tasklet_fn by spin_trylock and
reschedule tasklet in case of non-granted lock.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Acked-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jennifer Hunt [Sun, 15 Jul 2007 02:03:00 +0000 (19:03 -0700)]
[AF_IUCV]: Improve description of IUCV and AFIUCV configuration options.
Signed-off-by: Jennifer Hunt <jenhunt@us.ibm.com> Signed-off-by: Ursula Braun >braunu@de.ibm.com> Acked-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The set_multicast_list function may be called without holding the rtnl
mutex, resulting in races when changing the underlying device's promiscous
and allmulti state. Use the change_rx_mode hook, which is always invoked
under the rtnl.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 15 Jul 2007 01:52:02 +0000 (18:52 -0700)]
[NET]: dev_mcast: add multicast list synchronization helpers
The method drivers currently use to synchronize multicast lists is not
very pretty:
- walk the multicast list
- search each entry on a copy of the previous list
- if new add to lower device
- walk the copy of the previous list
- search each entry on the current list
- if removed delete from lower device
- copy entire list
This patch adds a new field to struct dev_addr_list to store the
synchronization state and adds two helper functions for synchronization
and cleanup.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 15 Jul 2007 01:51:31 +0000 (18:51 -0700)]
[NET]: Add net_device change_rx_mode callback
Currently the set_multicast_list (and set_rx_mode) callbacks are
responsible for configuring the device according to the IFF_PROMISC,
IFF_MULTICAST and IFF_ALLMULTI flags and the mc_list (and uc_list in
case of set_rx_mode).
These callbacks can be invoked from BH context without the rtnl_mutex
by dev_mc_add/dev_mc_delete, which makes reading the device flags and
promiscous/allmulti count racy. For real hardware drivers that just
commit all changes to the hardware this is not a real problem since
the stack guarantees to call them for every change, so at least the
final call will not race and commit the correct configuration to the
hardware.
For software devices that want to synchronize promiscous and multicast
state to an underlying device however this can cause corruption of the
underlying device's flags or promisc/allmulti counts.
When the software device is concurrently put in promiscous or allmulti
mode while set_multicast_list is invoked from bottem half context, the
device might synchronize the change to the underlying device without
holding the rtnl_mutex, which races with concurrent changes to the
underlying device.
Add a dev->change_rx_flags hook that is invoked when any of the flags
that affect rx filtering change (under the rtnl_mutex), which allows
drivers to perform synchronization immediately and only synchronize
the address lists in set_multicast_list/set_rx_mode.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o(.text+0x20af6): In function `scsi_dma_map':
: undefined reference to `dma_map_sg'
drivers/built-in.o(.text+0x20b5c): In function `scsi_dma_unmap':
: undefined reference to `dma_unmap_sg'
I split those functions out into a new file. Builds on s390 and i386.
Move scsi_dma_{map,unmap} into scsi_lib_dma.c which is only build if
HAS_DMA is set.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthew Wilcox [Wed, 11 Jul 2007 18:54:55 +0000 (12:54 -0600)]
[SCSI] Clean up scsi_add_lun a bit
This patch tidies up scsi_add_lun a bit. I rewrote the kerneldoc to match
the actual parameters, moved the check for RBC and MMC REPORT_LUN devices
away from the switch(), changed the setup of sdev->type to account for
BLIST_ISROM, moved the check for BLIST_NO_ULD_ATTACH further down in
the function, removed a bogus comment and fixed some whitespace issues.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Wed, 2007-06-06 at 11:55 -0700, David C Somayajulu wrote:
This patch fixes the code handling underrun and overrun conditions.
Also fixed coding style as per Mike Christie's advice.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- The saved sg_count was a leftover from the time the driver was doing
dma mapping by himself. But now that scsi-ml is called for the mapping
it is not the drivers responsibility.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Acked-by: G. Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sat, 14 Jul 2007 23:47:04 +0000 (18:47 -0500)]
[SCSI] lpfc: Fix NPIV compile problem
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_create_port':
drivers/scsi/lpfc/lpfc_init.c:1573: error: 'struct kobject' has no member named 'dentry'
Just remove the if check on this ... lpfc shouldn't be poking around
in kobject structures.
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_pci_probe_one':
drivers/scsi/lpfc/lpfc_init.c:1723: warning: unused variable 'retval'
And remove the unused variable.
Cc: James Smart <James.Smart@Emulex.Com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch uses dma_map_sg with phba->pcidev->dev instead of
scsi_dma_map.
scsi_dma_map doesn't work for NPIV since fc_vport->dev isn't fully
initialized. check_addr() in arch/x86_64/kernel/pci-nommu.c leads to
the crash since dev->dma_mask is NULL.
9p: fix a race condition bug in umount which caused a segfault
umounting partitions after heavy activity would sometimes trigger a
segmentation violation. This fix appears to remove that problem.
Fix originally provided by Latchesar Ionkov.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
During reorganization, the mount time debug option was removed in favor
of module-load-time parameters. However, the mount time option is still
a useful for feature during debug and for user-fault isolation when the
module is compiled into the kernel.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch expands the impact of the loose cache mode to allow for cached
metadata increasing the performance of directory listings and other metadata
read operations.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patchset moves non-filesystem interfaces of v9fs from fs/9p to net/9p.
It moves the transport, packet marshalling and connection layers to net/9p
leaving only the VFS related files in fs/9p. This work is being done in
preparation for in-kernel 9p servers as well as alternate 9p clients (other
than VFS).
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
David Chinner [Sat, 14 Jul 2007 06:05:04 +0000 (16:05 +1000)]
[LIB]: export radix_tree_preload()
XFS filestreams functionality uses radix trees and the preload
functions. XFS can be built as a module and hence we need
radix_tree_preload() exported. radix_tree_preload_end() is a
static inline, so it doesn't need exporting.
Signed-Off-By: Dave Chinner <dgc@sgi.com> Signed-Off-By: Tim Shimmin <tes@sgi.com>
Michal Marek [Wed, 11 Jul 2007 01:10:19 +0000 (11:10 +1000)]
[XFS] Fix XFS_IOC_FSBULKSTAT{,_SINGLE} & XFS_IOC_FSINUMBERS in compat mode
* 32bit struct xfs_fsop_bulkreq has different size and layout of
members, no matter the alignment. Move the code out of the #else
branch (why was it there in the first place?). Define _32 variants of
the ioctl constants.
* 32bit struct xfs_bstat is different because of time_t and on
i386 because of different padding. Make xfs_bulkstat_one() accept a
custom "output formatter" in the private_data argument which takes care
of the xfs_bulkstat_one_compat() that takes care of the different
layout in the compat case.
* i386 struct xfs_inogrp has different padding.
Add a similar "output formatter" mecanism to xfs_inumbers().
Michal Marek [Wed, 11 Jul 2007 01:10:09 +0000 (11:10 +1000)]
[XFS] Compat ioctl handler for handle operations
32bit struct xfs_fsop_handlereq has different size and offsets (due to
pointers). TODO: case XFS_IOC_{FSSETDM,ATTRLIST,ATTRMULTI}_BY_HANDLE still
not handled.
projects / linux-2.6-omap-h63xx.git / log