Pavel Emelyanov [Fri, 18 Apr 2008 06:17:34 +0000 (23:17 -0700)]
[INET]: Drop the inet_inherit_port() call.
As I can see from the code, two places (tcp_v6_syn_recv_sock and
dccp_v6_request_recv_sock) that call this one already run with
BHs disabled, so it's safe to call __inet_inherit_port there.
Besides (in case I missed smth with code review) the calltrace
tcp_v6_syn_recv_sock
`- tcp_v4_syn_recv_sock
`- __inet_inherit_port
and the similar for DCCP are valid, but assumes BHs to be disabled.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP: Initialize partial_bytes_acked to 0, when all of the data is acked.
According to RFC4960 7.2.2,
When all of the data transmitted by the sender has
been acknowledged by the recerver, partial_bytes_acked is initialized to 0.
This patch conforms to rfc requirement.
Without this fix, cwnd might be error incremented.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Tue, 15 Apr 2008 16:49:21 +0000 (12:49 -0400)]
phylib: factor out get_phy_id from within get_phy_device
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan Noe [Sun, 13 Apr 2008 02:34:38 +0000 (22:34 -0400)]
cxgb3: Fix __must_check warning with dev_dbg.
Fix the warning:
drivers/net/cxgb3/cxgb3_main.c: In function ‘offload_open’:
drivers/net/cxgb3/cxgb3_main.c:936: warning: ignoring return value of
‘sysfs_create_group’, declared with attribute warn_unused_result
Now the return value is checked; if sysfs_create_group() returns failure,
a warning is printed using dev_dbg, and the code continues as before. Use
of dev_dbg ensures printk is not needlessly included unless desired for
debugging.
Signed-off-by: Dan Noe <dpn@isomerica.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov [Sat, 12 Apr 2008 16:58:30 +0000 (20:58 +0400)]
natsemi: fix MMIO for PPC 44x platforms
The driver stores the PCI resource address into 'unsigned long' variable before
calling ioremap() on it. This warrants a kernel oops when the registers are
accessed on PPC 44x platforms which (being 32-bit) have PCI memory space mapped
beyond 4 GB.
The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion of the
PCI memory resources are mapped below 4 GB, but arch/powerpc/ code got rid of
this trick, having instead CONFIG_RESOURCES_64BIT enabled.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Allan Stephens [Thu, 17 Apr 2008 01:22:20 +0000 (18:22 -0700)]
[TIPC]: Cleanup of TIPC reference table code
This patch is a largely cosmetic cleanup of the TIPC reference
table code.
- The object reference field in each table entry is now single
32-bit integer instead of a union of two 32-bit integers.
- Variable naming has been made more consistent.
- Error message output has been made more consistent.
- Useless #includes have been eliminated.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 17 Apr 2008 01:21:16 +0000 (18:21 -0700)]
[TIPC]: Remove inlining of reference table locking routines
This patch converts the TIPC reference table locking routines
into non-inlined routines, since they are mainly called from
non-performance critical areas of TIPC and the added code
footprint incurred through inlining can no longer be justified.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Denys Vlasenko [Sun, 30 Mar 2008 23:02:43 +0000 (01:02 +0200)]
sb1000.c: stop inlining largish static functions
drivers/net/sb1000.c has lots of inlined static functions.
Mst of them are used at initialization, wait for some
hardware register to change (wait using yield, sleep etc),
or do slow port-based I/O. Inlining thse "for speed" makes no sense.
This patch removes "inline" from biggest static function
(regardless of number of callsites - gcc nowadays auto-inlines
statics with one callsite).
Size difference for 32bit x86:
text data bss dec hex filename
6299 129 0 6428 191c linux-2.6-ALLYES/drivers/net/sb1000.o
5418 129 0 5547 15ab linux-2.6.inline-ALLYES/drivers/net/sb1000.o
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Problem: If setting of an ip-address fails with LAN_OFFLINE,
qeth does not save the ip-address in its internal
list of set ip-addresses. qeth recovers after a
following STARTLAN event, but cannot set the unsaved
ip-address.
Solution: save the ip-address in the qeth-maintained list of
ip-addresses after a LAN_OFFLINE failure for SETIP.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Frank Blaschka [Tue, 1 Apr 2008 08:26:59 +0000 (10:26 +0200)]
qeth: core code should alloc headroom for LLC protocol
Allocate headroom for TR_HLEN but using only ETH_HLEN causes rx
performance degradation. Allocate ETH_HLEN for ethernet and
TR_HLEN for token ring (layer 3 mode).
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Tiedemann [Tue, 1 Apr 2008 08:26:58 +0000 (10:26 +0200)]
qeth: improving debug message handling
Improving debug message handling, moving ipa into messages from kernel
to dbf, some cleanups and typo fixes.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qeth: CCL-sequence numbers required for protocol ETH_P_802_2 only
Symptom: slow CCL response time
Problem: non-ETH_P_802_2 packets are not delivered to NDH for
CCL. But CCL detects missing sequence numbers, which
cause a serious performance problem with CCL.
Solution: assign sequence numbers only to 802.2 packets.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qeth: set lan_online flag after a received STARTLAN
Problem: A STARTLAN command from the adapter may arrive while a
qeth recovery is currently running with a failed qeth
STARTLAN. Usually qeth schedules a recovery when
receiving a STARTLAN command from the adapter. But
another recovery scheduled while a recovery is already
running never starts. Thus the qeth-administered
lan_online flag remains zero in this scenario, even
though the adapter-STARTLAN has happened.
Solution: Set lan_online flag for a received STARTLAN from the
adapter in case scheduled recovery does not start.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OSA-adapters do not have an address limitation for the qdio queue
structures except the MAX storage level of the current processor.
And due to a recent z/VM APAR there is no longer a restriction to
allocate qdio structures below 2 GB.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qeth: improve ip_list administration after deregister failures
1. ip_list handling after deregister failure of multicast address:
If error code "MC Address not found" is returned do not re-add
multicast address to ip_list.
For other error codes readd multicast address at the end of
function qeth_delete_all_mc.
2. ip_list handling after deregister failure or normal ip address:
If error code "IP Address not found" is returned do not re-add
multicast address to ip list.
This is especially important in IP address takeover scenarios,
to enable re-takeover of a taken over IP address.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Wed, 2 Apr 2008 20:48:23 +0000 (13:48 -0700)]
e1000e: reformat register test code, fix some minor initialization
The register tests should be run with all the proper flags enabled
to maximize the test coverage code and make sure we are as close
as we can get to testing regular traffic.
Reformat the code for readability. Minor cleanups in the descriptor
ring setup.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev_alloc_skb since it handles any NUMA node memory localtion issues
and sets skb->dev. Since device driver was not setting skb->dev, I bet
filter rules based on device would not work.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Any negative return value from start_xmit is interpreted as NETDEV_TX_LOCK
which is not what this driver wants. It should return 0 (NETDEV_TX_OK)
when it consumes a packet.
Also, use skb_padto() as the generic way to pad small frames.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch works around the MWI bug on the DC21143 rev 65 Tulip by
ensuring that the receive buffers don't end on a cache line boundary
(as documented in the errata).
This patch is required for the MIPS based Cobalt Qube/RaQ as
supporting the extra PCI commands seems to reduce the chance of a hard
lockup between the Tulip and the PCI bridge.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jeff Garzik [Thu, 17 Apr 2008 00:37:24 +0000 (20:37 -0400)]
[netdrvr] tulip/winbond-840: don't let tulip.h symbol stomp ours
winbond-840 shares tulip.h with the tulip driver, because they share
many (but not all) of the same register definitions.
This is useful for the register definitions, but not helpful when it
comes to symbols that are shared among the tulip driver's C modules,
but not meant to be shared outside that one driver.
Thus, PKT_BUF_SZ is a symbol internal to tulip, but it was intruding
upon a similar symbol in winbond-840's namespace. This was not a
problem as long as the two symbols had the same value, but upcoming
patches result in differing symbol values.
Andy Fleming [Thu, 10 Apr 2008 00:38:13 +0000 (19:38 -0500)]
phy: Change mii_bus id field to a string
Having the id field be an int was making more complex bus topologies
excessively difficult. For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dai Haruki [Thu, 10 Apr 2008 00:37:51 +0000 (19:37 -0500)]
gianfar: Support NAPI for TX Frames
Poll the completed TX frames in gfar_poll(). This prevents the tx
completion interrupt from interfering with processing of received
frames.
We also disable hardware rx coalescing when NAPI is enabled.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch revises the logging for link informations of spidernet.
- The link down message is too verbose because auto-negotiation timeout
occurs periodically while an ethernet cable is not connected.
- We want to see the link result, and we think it should be displayed.
In addition to the value of GHIINT0STS, spidernet interrupt handler
should check the values of GHIINT1STS/GHIINT2STS registers at the
beginning of spider_net_interrupt() so as not to drop error
interrupts.
GHIINT1STS/GHIINT2STS registers indicates some of erroneous conditions
in spidernet, and a few bits of GHIINT0STS register reflects these
conditions. But GHIINT0MSK masks these bits, so you should check these
conditions by reading GHIINT1STS/GHIINT2STS registers directly.
- unmask GDAINVAINT. There is an operation to do by spidernet
interrupt handler.
- mask some interrupts. There are no operations in the interrupt handler.
In error and warning printks, always report the netdevice name
instead of the port index (the latter has no meaning when there
are multiple mv643xx_eth silicon blocks in the system.)
mv643xx_eth: identify ports by struct mv643xx_private *
Instead of identifying individual mv643xx ethernet ports by only
their port number, identify them by their struct mv643xx_private *,
as just a port number has no meaning when there are multiple
mv643xx_eth silicon blocks in the system.
- Remove unused MV643XX_DEFAULT_[RT]X_QUEUE_SIZE definitions.
- Remove ETH_TARGET enum -- it isn't used anywhere in the driver,
and isn't even valid for non-mv643xx chip models, as those use
different MBUS target IDs.
- Clean up comment and control flow in mv643xx_eth_change_mtu().
- Use mp->dev instead of mp->mii.dev in mv643xx_eth_tx_timeout_task().
- Make mv643xx_eth_free_tx_descs() static.
- Remove overzealous NULL check in mv643xx_eth_start_xmit().
- Use symbolic NETDEV_TX_* constants in mv643xx_eth_start_xmit().
Johannes Berg [Wed, 16 Apr 2008 15:43:20 +0000 (17:43 +0200)]
mac80211: rework scanning to account for probe response/beacon difference
This patch reworks the scanning code (ieee80211_rx_bss_info) to take
more parameters from beacons and keep a BSS info structure alive when
only beacons for it are received. This fixes a problem with iwlwifi
drivers (where we don't understand the root cause of the problem yet)
and another driver for some broken hardware (which cannot send probe
requests unless associated, so can't always actively scan.)
Signed-off-by: Bill Moss <bmoss@clemson.edu>
[jmberg: reformatted comments, make probe_resp a bool] Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Wed, 16 Apr 2008 15:49:02 +0000 (18:49 +0300)]
ath5k: Misc fixes/cleanups
*Handle MIB interrupts and pass low level stats to mac80211
*Add Power On Self Test function
*Update to match recent dumps
*Let RF2425 attach so we can further test it
*Remove unused files regdom.c and regdom.h
base.c
Changes-licensed-under: 3-clause-BSD
rest
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: Use HW acceleration decryption by default
This patch reverses the hw_crypto logic and makes HW crypto a default.
Giving swcrypto=1 as parameter to the module disables HW crypto.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Tue, 15 Apr 2008 23:01:46 +0000 (16:01 -0700)]
iwlwifi: fix unload warning and error
This patch fix the error we get when unload the driver, No space for Tx.
The cause of this problem is related to receiving late SW rfkill from
rfkill subsystem during the driver teardown causing this error.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 15 Apr 2008 23:01:45 +0000 (16:01 -0700)]
iwlwifi: arrange max number of Tx queues
This patch increases the max possible number of Tx queues, but leaves
current used number of queues as HW dependent
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: Fix TKIP update key and get_free_ucode_key
This patch fixes a bug in update_tkip_key: only one key needs to be
allocated in uCode, every time it is updated, the old one will be
overwritten
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 23:01:43 +0000 (16:01 -0700)]
iwlwifi: move rxon associated command to hcmd
This patch run rxon associated command from hcmd handler
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 23:01:42 +0000 (16:01 -0700)]
iwlwifi: introduce host commands callbacks
This patch adds place holder for host command handlers
for supporting different implementations per HW
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 15 Apr 2008 23:01:41 +0000 (16:01 -0700)]
iwlwifi: move HW device registration
This patch moves the HW device registration from the iwl-4965.c file, which
implies a HW specific support, to a more general location.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 23:01:40 +0000 (16:01 -0700)]
iwlwifi: move the creation of LQ host command to iwlcore
This patch moves creation of LQ host command to iwlcore
from previous location in rate scaling.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 23:01:39 +0000 (16:01 -0700)]
iwlwifi: support different num of tx and rx antennas
This patch adds infrastructure for supporting different
number of tx and rx antennas
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 23:01:38 +0000 (16:01 -0700)]
iwlwifi: hw_setting cleanup
1. This patch renames hw_setting to hw_params
2. Align names of the structure and variables
3. set_hw_params is called from libs_ops
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) It removes the statistics work. The request statistics command is
sent in ASYNC mode in this flow, the mutex is uneeded, so the request
statistics function can't go to sleep. No need for a workqueue anymore.
2) iwl4965_send_statistics_request has been renamed to
iwl_send_statistics_request and moved to iwl-core.c
3) A request for statistics is sent in alive_notify, the makes the uCode
sends statistics notification periodically starting from association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Tue, 15 Apr 2008 19:13:36 +0000 (21:13 +0200)]
b43: Add fastpath to b43_mac_suspend()
This adds a fastpath for the common workloads to the
MAC suspend flushing.
In common workloads the FIFO flush will take between 100 and
200 microseconds. So we want to avoid calling msleep() in the
common case, as it will waste over 800 microseconds + scheduler
overhead.
This fastpath will hit in workloads where only small chunks
of data are transmitted (downloading a file) or when a TX rate bigger
or equal to 24MBit/s is used when transmitting lots of stuff (iperf).
So in the commonly used workloads it will basically always hit.
In case the fastpath is not hit, there's no real performance or latency
disadvantage from that.
And yes, I measured this. So this is not one of these
bad Programmer Likeliness Assumptions that are always wrong. ;)
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 04:16:14 +0000 (21:16 -0700)]
iwlwifi: move shared pointers to iwl_priv
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: perform bss_info_changed post association work right away
Do not use workqueue for bss_info_changed post association work.
When driver is notified of association the upper layer will be notified
right after that the association is complete. Doing the post association
work in a workqueue introduces a race condition where the upper layer may
want to make use of the association, but it is not yet complete.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change CONFIG_IWLCORE_RFKILL to CONFIG_IWLWIFI_RFKILL to
be more consistent with other config variables.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965: make iwl4965_send_rxon_assoc asynchronous
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 04:16:10 +0000 (21:16 -0700)]
iwlwifi: Fix byte count table for fragmented packets
This patch fix byte count table update. Table must be updated for each
fragment
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves security related functions to iwl-sta.c.
Note that iwl4965_mac_update_tkip_key is still in iwl4965-base.c since it
is a mac80211 handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix book keeping of key table in the driver
to be synchronized with uCode
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for HW encryption/decryption in 1X WEP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds HW encryption support in default WEP mode.
When no key mapping key/pairwise key is used. The key is broadcast key
is used as default/global/static key.
This code assumes that group cast key is added after pairwise key.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declaration for static WEP host command. This command will
be used for default WEP group keys when no key mapping keys are used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Apr 2008 04:16:03 +0000 (21:16 -0700)]
iwlwifi: generalize iwlwifi init flow
This patch creates handlers to support
iwlwifi init flow for multiple HWs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 13 Apr 2008 08:43:50 +0000 (10:43 +0200)]
mac80211: fix key todo list order
When we add multiple todo entries, we rely on them being executed
mostly in the right order, especially when a key is being replaced.
But when a default key is replaced, the todo list order will differ
from the order when the key being replaced is not a default key, so
problems will happen. Hence, just move each todo item to the end of
the list when it is added so we can in the other code ensure that
hw accel for a key will be disabled before it is enabled for the
replacement.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Apr 2008 19:40:35 +0000 (21:40 +0200)]
mac80211: fix spinlock recursion
When STAs are expired, we need to hold the sta_lock. Using
the same lock for keys too would then mean we'd need another
key free function, and that'll just lead to confusion, so just
use a new spinlock for all key lists.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
proc: switch /proc/driver/ray_cs/ray_cs to seq_file interface
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Jean Tourrilhes <jt@hpl.hp.com> Cc: David S. Miller <davem@davemloft.net> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: no BSS changes to driver from beacons processed during scanning
There is no need to send BSS changes to driver from beacons processed
during scanning. We are more interested in beacons from an AP with which
we are associated - these will still be used to send updates to driver as
the beacons are received without scanning.
This change·removes the requirement that bss_info_changed needs to be atomic.
The beacons received during scanning are processed from a tasklet, but if we
do not call bss_info_changed for these beacons there is no need for it to be
atomic. This function (bss_info_changed) is called either from workqueue or
ioctl in all other instances.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some command structs contain reserved or unused fields, which the driver
send uninitialized down to the card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas: convert libertas driver to use an event/cmdresp queue
This patch (co-developed by Dan Williams and Holger Schurig) uses a kfifo
object for events and a swapping buffer scheme for the command response to
preserve the zero-copy semantics of the CF driver and keep memory usage low.
The main thread should only ever touch the buffer indexed by priv->resp_idx,
while the interface code is free to write to the second buffer, then swap
priv->resp_idx under the driver spinlock. The firmware specs only permit
one in-flight command, so there will only ever be one command response to
process at a time.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 9 Apr 2008 18:46:27 +0000 (20:46 +0200)]
rt2x00: Only free skb when beacon_update fails
In rt2x00lib_intf_scheduled_iter() we use the hw->beacon_update()
callback function. This means that it should behave similarly as mac80211
when that uses the function.
This means that the skb should only be freed when beacon_update() has failed,
otherwise the driver is the owner and is responsible for freeing the buffer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 9 Apr 2008 14:45:37 +0000 (16:45 +0200)]
mac80211: fix key hwaccel race
The previous key locking patch left a small race: it would be possible
to add a key and take the interface down before the key todo is run so
that hwaccel for that key is enabled on an interface that is down. Avoid
this by running the todo list when an interface is brought up or down.
This patch also fixes a small bug: before this change, a few functions
used the key list without the lock that protects it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John Heffner [Tue, 15 Apr 2008 22:26:39 +0000 (15:26 -0700)]
[TCP]: Increase the max_burst threshold from 3 to tp->reordering.
This change is necessary to allow cwnd to grow during persistent
reordering. Cwnd moderation is applied when in the disorder state
and an ack that fills the hole comes in. If the hole was greater
than 3 packets, but less than tp->reordering, cwnd will shrink when
it should not have.
Signed-off-by: John Heffner <jheffner@napa.(none)> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log