travis@sgi.com [Wed, 30 Jan 2008 12:32:51 +0000 (13:32 +0100)]
percpu: use a kconfig variable to signal arch specific percpu setup
The use of the __GENERIC_PERCPU is a bit problematic since arches
may want to run their own percpu setup while using the generic
percpu definitions. Replace it through a kconfig variable.
Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
H. Peter Anvin [Wed, 30 Jan 2008 12:32:51 +0000 (13:32 +0100)]
i386: handle an initrd in highmem (version 2)
The boot protocol has until now required that the initrd be located in
lowmem, which makes the lowmem/highmem boundary visible to the boot
loader. This was exported to the bootloader via a compile-time
field. Unfortunately, the vmalloc= command-line option breaks this
part of the protocol; instead of adding yet another hack that affects
the bootloader, have the kernel relocate the initrd down below the
lowmem boundary inside the kernel itself.
Note that this does not rely on HIGHMEM being enabled in the kernel.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Miguel Boton [Wed, 30 Jan 2008 12:32:51 +0000 (13:32 +0100)]
x86: reboot_{32|64}.c unification
reboot_{32|64}.c unification patch.
This patch unifies the code from the reboot_32.c and reboot_64.c files.
It has been tested in computers with X86_32 and X86_64 kernels and it
looks like all reboot modes work fine (EFI restart system hasn't been
tested yet).
Probably I made some mistakes (like I usually do) so I hope
we can identify and fix them soon.
Signed-off-by: Miguel Boton <mboton@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Arjan van de Ven [Wed, 30 Jan 2008 12:32:50 +0000 (13:32 +0100)]
debug: add the end-of-trace marker and the module list to
Unlike oopses, WARN_ON() currently does't print the loaded modules list.
This makes it harder to take action on certain bug reports. For example,
recently there were a set of WARN_ON()s reported in the mac80211 stack,
which were just signalling a driver bug. It takes then anther round trip
to the bug reporter (if he responds at all) to find out which driver
is at fault.
Another issue is that, unlike oopses, WARN_ON() doesn't currently printk
the helpful "cut here" line, nor the "end of trace" marker.
Now that WARN_ON() is out of line, the size increase due to this is
minimal and it's worth adding.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Arjan van de Ven [Wed, 30 Jan 2008 12:32:50 +0000 (13:32 +0100)]
debug: move WARN_ON() out of line
A quick grep shows that there are currently 1145 instances of WARN_ON
in the kernel. Currently, WARN_ON is pretty much entirely inlined,
which makes it hard to enhance it without growing the size of the kernel
(and getting Andrew unhappy).
This patch build on top of Olof's patch that introduces __WARN,
and places the slowpath out of line. It also uses Ingo's suggestion
to not use __FUNCTION__ but to use kallsyms to do the lookup;
this saves a ton of extra space since gcc doesn't need to store the function
string twice now:
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: Olof Johansson <olof@lixom.net> Acked-by: Matt Meckall <mpm@selenic.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
c0113218 T acpi_restore_state_mem c0113219 T acpi_save_state_mem
<Big Hole> c0114000 t wakeup_code
This is because arch/x86/kernel/acpi/wakeup_32.S forces a .text alignment
of 4096 bytes. (I have no idea if it is really needed, since
arch/x86/kernel/acpi/wakeup_64.S uses a 16 bytes alignment *only*)
So arch/x86/kernel/built-in.o also has this alignment
arch/x86/kernel/built-in.o: file format elf32-i386
Sections:
Idx Name Size VMA LMA File off Algn
0 .text 00018c94000000000000000000001000 2**12
CONTENTS, ALLOC, LOAD, RELOC, READONLY, CODE
But as arch/x86/kernel/acpi/wakeup_32.o is not the first object linked
into arch/x86/kernel/built-in.o, linker had to build several holes to meet
alignement requirements, because of .o nestings in the kbuild process.
This can be solved by using a special section, .text.page_aligned, so that
no holes are needed.
# size vmlinux.before vmlinux.after
text data bss dec hex filename 4619942 422838 458752 5501532 53f25c vmlinux.before 4610534 422838 458752 5492124 53cd9c vmlinux.after
This saves 9408 bytes
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
1. Defines arch-specific types for the contents of a pagetable entry.
That is, 32-bit entries for 32-bit non-PAE, and 64-bit entries for
32-bit PAE and 64-bit. However, even though the latter two are the
same size, they're defined with different types in order to retain
compatibility with printk format strings, etc.
2. Defines arch-specific pte_t. This is different because 32-bit PAE
defines it in two halves, whereas 32-bit PAE and 64-bit define it as a
single entry. All the other pagetable levels can be defined in a
common way. This also defines arch-specific pte_val/make_pte functions.
3. Define PAGETABLE_LEVELS for each architecture variation, for later use.
4. Define common pagetable entry accessors in a paravirt-compatible
way. (64-bit does not yet use paravirt-ops in any way).
5. Convert a few instances of using a *_val() as an lvalue where it is
no longer a macro. There are still places in the 64-bit code which
use pte_val() as an lvalue.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move, and to some extent unify, the various page copying and clearing
functions. The only unification here is that both architectures use
the same function for copying/clearing user and kernel pages.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
are supposed to fix the detection of contant TSC for AMD CPUs.
Unfortunately on x86_64 it does still not work with current x86/mm.
For a Phenom I still get:
...
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2288.366 MHz processor.
...
We have to set c->x86_power in early_identify_cpu to properly detect
the CONSTANT_TSC bit in early_init_amd.
Attached patch fixes this issue. Following the relevant boot
messages when the fix is used:
Andi Kleen [Wed, 30 Jan 2008 12:32:41 +0000 (13:32 +0100)]
x86: don't disable TSC in any C states on AMD Fam10h
The ACPI code currently disables TSC use in any C2 and C3
states. But the AMD Fam10h BKDG documents that the TSC
will never stop in any C states when the CONSTANT_TSC bit is
set. Make this disabling conditional on CONSTANT_TSC
not set on AMD.
I actually think this is true on Intel too for C2 states
on CPUs with p-state invariant TSC, but this needs
further discussions with Len to really confirm :-)
Andi Kleen [Wed, 30 Jan 2008 12:32:40 +0000 (13:32 +0100)]
x86: allow TSC clock source on AMD Fam10h and some cleanup
After a lot of discussions with AMD it turns out that TSC
on Fam10h CPUs is synchronized when the CONSTANT_TSC cpuid bit is set.
Or rather that if there are ever systems where that is not
true it would be their BIOS' task to disable the bit.
So finally use TSC gettimeofday on Fam10h by default.
Or rather it is always used now on CPUs where the AMD
specific CONSTANT_TSC bit is set.
This gives a nice speed bost for gettimeofday() on these systems
which tends to be by far the most common v/syscall.
On a Fam10h system here TSC gtod uses about 20% of the CPU time of
acpi_pm based gtod(). This was measured on 32bit, on 64bit
it is even better because TSC gtod() can use a vsyscall
and stay in ring 3, which acpi_pm doesn't.
The Intel check simply checks for CONSTANT_TSC too without hardcoding
Intel vendor. This is equivalent on 64bit because all 64bit capable Intel
CPUs will have CONSTANT_TSC set.
On Intel there is no CPU supplied CONSTANT_TSC bit currently,
but we synthesize one based on hardcoded knowledge which steppings
have p-state invariant TSC.
So the new logic is now: On CPUs which have the AMD specific
CONSTANT_TSC bit set or on Intel CPUs which are new enough
to be known to have p-state invariant TSC always use
TSC based gettimeofday()
Andi Kleen [Wed, 30 Jan 2008 12:32:38 +0000 (13:32 +0100)]
x86: introduce rdtsc_barrier()
rdtsc_barrier() is a new barrier primitive that stops RDTSC speculation
to avoid races with timer interrupts on other CPUs.
It expands either to LFENCE (for Intel CPUs) or MFENCE (for
AMD CPUs) which stops RDTSC on all currently known microarchitectures
that implement SSE. On CPUs without SSE there is generally no RDTSC
speculation.
[ mingo@elte.hu: renamed it to rdtsc_barrier() and made it x86-only ]
WANG Cong [Wed, 30 Jan 2008 12:32:38 +0000 (13:32 +0100)]
git-x86: unbreak UML
Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Quentin Barnes [Wed, 30 Jan 2008 12:32:32 +0000 (13:32 +0100)]
x86: code clarification patch to Kprobes arch code
When developing the Kprobes arch code for ARM, I ran across some code
found in x86 and s390 Kprobes arch code which I didn't consider as
good as it could be.
Once I figured out what the code was doing, I changed the code
for ARM Kprobes to work the way I felt was more appropriate.
I've tested the code this way in ARM for about a year and would
like to push the same change to the other affected architectures.
The code in question is in kprobe_exceptions_notify() which
does:
====
/* kprobe_running() needs smp_processor_id() */
preempt_disable();
if (kprobe_running() &&
kprobe_fault_handler(args->regs, args->trapnr))
ret = NOTIFY_STOP;
preempt_enable();
====
For the moment, ignore the code having the preempt_disable()/
preempt_enable() pair in it.
The problem is that kprobe_running() needs to call smp_processor_id()
which will assert if preemption is enabled. That sanity check by
smp_processor_id() makes perfect sense since calling it with preemption
enabled would return an unreliable result.
But the function kprobe_exceptions_notify() can be called from a
context where preemption could be enabled. If that happens, the
assertion in smp_processor_id() happens and we're dead. So what
the original author did (speculation on my part!) is put in the
preempt_disable()/preempt_enable() pair to simply defeat the check.
Once I figured out what was going on, I considered this an
inappropriate approach. If kprobe_exceptions_notify() is called
from a preemptible context, we can't be in a kprobe processing
context at that time anyways since kprobes requires preemption to
already be disabled, so just check for preemption enabled, and if
so, blow out before ever calling kprobe_running(). I wrote the ARM
kprobe code like this:
====
/* To be potentially processing a kprobe fault and to
* trust the result from kprobe_running(), we have
* be non-preemptible. */
if (!preemptible() && kprobe_running() &&
kprobe_fault_handler(args->regs, args->trapnr))
ret = NOTIFY_STOP;
====
The above code has been working fine for ARM Kprobes for a year.
So I changed the x86 code (2.6.24-rc6) to be the same way and ran
the Systemtap tests on that kernel. As on ARM, Systemtap on x86
comes up with the same test results either way, so it's a neutral
external functional change (as expected).
This issue has been discussed previously on linux-arm-kernel and the
Systemtap mailing lists. Pointers to the by base for the two
discussions:
http://lists.arm.linux.org.uk/lurker/message/20071219.223225.1f5c2a5e.en.html
http://sourceware.org/ml/systemtap/2007-q1/msg00251.html
Signed-off-by: Quentin Barnes <qbarnes@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com> Acked-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Ingo Molnar [Wed, 30 Jan 2008 12:32:31 +0000 (13:32 +0100)]
x86: hlt on early crash
H. Peter Anvin <hpa@zytor.com> wrote:
> It probably should actually HLT, to avoid sucking power, and stressing
> the thermal system. We're dead at this point, and the early 486's
> which had problems with HLT will lock up - we don't care.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sam Ravnborg [Wed, 30 Jan 2008 12:32:27 +0000 (13:32 +0100)]
x86: unify arch/x86/kernel/Makefile(s)
Combine the 32 and 64 bit specific Makefiles in one file.
While doing so link order was (almost) preserved on 32 bit
but on 64 bit link order changed a lot.
Patch was checked with defconfig + allyesconfig builds.
The same .o files were linked in these configurations.
To keep readability of the Makefiles a few Kconfig
symbols was added/modified and it was checked that
they were not used anywhere else.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sam Ravnborg [Wed, 30 Jan 2008 12:32:27 +0000 (13:32 +0100)]
x86: teach vdso to clean
A few files remained after 'make clean' in arch/x86/vdso/.
Teach vdso to clean up those files in a bit brutal fashion.
The filenames are just hardcoded in the Makefile.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Roland McGrath <roland@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sam Ravnborg [Wed, 30 Jan 2008 12:32:21 +0000 (13:32 +0100)]
x86: share more options between 32 and 64 bit build
On recommendation from Andi Kleen share a few more options
between 32 and 64 bit builds.
A defconfig build for i386 did not show any difference in
size of text and data.
Sam Ravnborg [Wed, 30 Jan 2008 12:32:20 +0000 (13:32 +0100)]
x86: unification of arch/x86/Makefiles
Unify the 32 and 64 bit specific Makefiles.
The unification was simplest to do in one step although the
readability of the patch suffers a bit from this.
Noteworthy remarks on the unification:
- The 64 bit cpu stuff should be moved to Makefile_32.cpu
but I did not feel confident doing it due to subtle differences
- The use of cflags-y were abandoned since we have seen one bug where
we did wrong due to missing assignment to KBUILD_CFLAGS.
The cc-option marcro uses KBUILD_CFLAGS.
- The "No need to remake" line are deleted. It caused "make -B" to fail
- For 64 bit the sub architecture stuff is not used.
- The way head64.o is specified could be nicer - but it awaits the
introduction of head32.o (which seems like a win to introduce for readability)
- Patch is checkpatch clean
Patch is tested by doing a defconfig build for i386 and x86_64 and in both
cases monitoring that only relevant files were recompiled when applying
the patch.
[ mingo@elte.hu: build fix ]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Harvey Harrison [Wed, 30 Jan 2008 12:32:19 +0000 (13:32 +0100)]
x86: kprobes change kprobe_handler flow
Make the control flow of kprobe_handler more obvious.
Collapse the separate if blocks/gotos with if/else blocks
this unifies the duplication of the check for a breakpoint
instruction race with another cpu.
Create two jump targets:
preempt_out: re-enables preemption before returning ret
out: only returns ret
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Harvey Harrison [Wed, 30 Jan 2008 12:32:19 +0000 (13:32 +0100)]
x86: cosmetic fixes fault_{32|64}.c
First step towards unifying these files.
- Checkpatch trailing whitespace fixes
- Checkpatch indentation of switch statement fixes
- Checkpatch single statement ifs need no braces fixes
- Checkpatch consistent spacing after comma fixes
- Introduce defines for pagefault error bits from X86_64 and add useful
comment from X86_32. Use these defines in X86_32 where obvious.
- Unify comments between 32|64 bit
- Small ifdef movement for CONFIG_KPROBES in notify_page_fault()
- Introduce X86_64 only case statement
No Functional Changes.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/math-emu/errors.c:163: warning: format '%ld' expects type 'long int', but argument 3 has type 'u32'
arch/x86/math-emu/errors.c:175: warning: format '%ld' expects type 'long int', but argument 3 has type 'u32'
arch/x86/math-emu/errors.c:175: warning: format '%ld' expects type 'long int', but argument 4 has type 'u32'
arch/x86/math-emu/errors.c:175: warning: format '%ld' expects type 'long int', but argument 5 has type 'u32'
arch/x86/math-emu/errors.c:175: warning: format '%ld' expects type 'long int', but argument 6 has type 'u32'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
WARNING: line over 80 characters
#45: FILE: arch/x86/kernel/cpu/mcheck/k7.c:50:
+ snprintf (addr, 24, " at %08x%08x", ahigh, alow);
WARNING: no space between function name and open parenthesis '('
#45: FILE: arch/x86/kernel/cpu/mcheck/k7.c:50:
+ snprintf (addr, 24, " at %08x%08x", ahigh, alow);
WARNING: no space between function name and open parenthesis '('
#48: FILE: arch/x86/kernel/cpu/mcheck/k7.c:52:
+ printk (KERN_EMERG "CPU %d: Bank %d: %08x%08x%s%s\n",
WARNING: no space between function name and open parenthesis '('
#65: FILE: arch/x86/kernel/cpu/mcheck/p4.c:161:
+ printk (KERN_DEBUG "CPU %d: EIP: %08x EFLAGS: %08x\n"
WARNING: no space between function name and open parenthesis '('
#88: FILE: arch/x86/kernel/cpu/mcheck/p4.c:182:
+ snprintf (misc, 20, "[%08x%08x]", ahigh, alow);
WARNING: line over 80 characters
#93: FILE: arch/x86/kernel/cpu/mcheck/p4.c:186:
+ snprintf (addr, 24, " at %08x%08x", ahigh, alow);
WARNING: no space between function name and open parenthesis '('
#93: FILE: arch/x86/kernel/cpu/mcheck/p4.c:186:
+ snprintf (addr, 24, " at %08x%08x", ahigh, alow);
WARNING: no space between function name and open parenthesis '('
#96: FILE: arch/x86/kernel/cpu/mcheck/p4.c:188:
+ printk (KERN_EMERG "CPU %d: Bank %d: %08x%08x%s%s\n",
WARNING: no space between function name and open parenthesis '('
#120: FILE: arch/x86/kernel/cpu/mcheck/p6.c:46:
+ snprintf (misc, 20, "[%08x%08x]", ahigh, alow);
WARNING: line over 80 characters
#125: FILE: arch/x86/kernel/cpu/mcheck/p6.c:50:
+ snprintf (addr, 24, " at %08x%08x", ahigh, alow);
WARNING: no space between function name and open parenthesis '('
#125: FILE: arch/x86/kernel/cpu/mcheck/p6.c:50:
+ snprintf (addr, 24, " at %08x%08x", ahigh, alow);
WARNING: no space between function name and open parenthesis '('
#128: FILE: arch/x86/kernel/cpu/mcheck/p6.c:52:
+ printk (KERN_EMERG "CPU %d: Bank %d: %08x%08x%s%s\n",
total: 0 errors, 13 warnings, 100 lines checked
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Min Zhang <mzhang@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Min Zhang [Wed, 30 Jan 2008 12:32:11 +0000 (13:32 +0100)]
arch/x86/kernel/cpu/mcheck/p4.c: cleanups
SMP, the machine check exception dispatches all logical processors within a
physical package to the machine-check exception handler, so the printk
within each handler outputs concurrently and makes the output unreadable.
Refer to Intel system programming guide Part 1 Section 7.8.5
http://developer.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Min Zhang <mzhang@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
replace x86_read/write_per_cpu with a common function.
x86_read_per_cpu() and its writeish sister are not present in x86_64. So in
this patch, we replace them with __get_cpu_var(), which is present in both
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Like i386, x86_64 also need to include its own patching function.
(Well, if you're not in a hurry, and don't care about speed, you don't
really _need_ ;-))
So here they are. Not much different in essence from i386
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core patching code for paravirt is sufficiently different
among i386 and x86_64, and we move them to specific files.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86_64 needs a potentially larger clobber list than i386, due to its calling
convention. So we add more CLBR_ defines for it.
Note that CLBR_ANY is different for each of the architectures, since it comprises
the notion of "All call clobbers in this architecture"
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the advent of ticket locking, CLI_STRING, STI_STRING, and friends
are not used anymore. They can now be safely deleted.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86: replace privileged instructions with paravirt macros
The assembly code in entry_64.S issues a bunch of privileged instructions,
like cli, sti, swapgs, and others. Paravirt guests are forbidden to do so,
and we then replace them with macros that will do the right thing.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds paravirt hook for swapgs operation, which is a privileged
operation in x86_64.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
i386 has a macro GET_CR0_INTO_EAX, used in early trap handling code.
x86_64 has similar needs, only it needs to put cr2 into rcx. We provide
a macro for such task, in the same way
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch changes the irq handling function definitions
in paravirt.h (like raw_local_irq_disable) to accomodate for x86_64.
The differences are in the calling convention.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adjust the paravirt macros used in assembly code
to accomodate for x86_64 as well.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86: change assembly definition of paravirt_patch_site
To account for differences in x86_64, we change the macros that
create raw instances of the paravirt_patch_site struct.
We need to align 64-pointers to 64-bit boundaries, so we add an alignment
directive. Also, we need to make room for a word-sized pointer,
instead of a fixed 32-bit one
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a field in pv_cpu_ops for a paravirtualized hook
for rdtscp, needed for x86_64.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
write_tsc() does not need to be enclosed in any paravirt closure,
as it uses wrmsr(). So we rip off the duplicate in msr.h
and the definition from paravirt.h
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adjust the PVOP_VCALL and PVOP_CALL macros to
work with x86_64. It has a different calling convention, and
we use auxiliary macros to account for both calling conventions
as cleanly as possible
Comments are adjusted accordingly.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
projects / linux-2.6-omap-h63xx.git / log