Matthias Gehre [Tue, 28 Mar 2006 09:56:48 +0000 (01:56 -0800)]
[PATCH] Replace 0xff.. with correct DMA_xBIT_MASK
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Arjan van de Ven [Tue, 28 Mar 2006 09:56:42 +0000 (01:56 -0800)]
[PATCH] Make most file operations structs in fs/ const
This is a conversion to make the various file_operations structs in fs/
const. Basically a regexp job, with a few manual fixups
The goal is both to increase correctness (harder to accidentally write to
shared datastructures) and reducing the false sharing of cachelines with
things that get dirty in .data (while .rodata is nicely read only and thus
cache clean)
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arjan van de Ven [Tue, 28 Mar 2006 09:56:41 +0000 (01:56 -0800)]
[PATCH] mark f_ops const in the inode
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu() is a for-loop over cpu_possible_map. for_each_online_cpu is
for-loop cpu over cpu_online_map. .....for_each_cpu() is not sufficiently
explicit and can lead to mistakes.
This patch adds for_each_possible_cpu() in preparation for the removal of
for_each_cpu().
Vadim Lobanov [Tue, 28 Mar 2006 09:56:35 +0000 (01:56 -0800)]
[PATCH] Fold select_bits_alloc/free into caller code.
Remove an unnecessary level of indirection in allocating and freeing select
bits, as per the select_bits_alloc() and select_bits_free() functions.
Both select.c and compat.c are updated.
Andi Kleen [Tue, 28 Mar 2006 09:56:33 +0000 (01:56 -0800)]
[PATCH] Optimize select/poll by putting small data sets on the stack
Optimize select and poll by a using stack space for small fd sets
This brings back an old optimization from Linux 2.0. Using the stack is
faster than kmalloc. On a Intel P4 system it speeds up a select of a
single pty fd by about 13% (~4000 cycles -> ~3500)
It also saves memory because a daemon hanging in select or poll will
usually save one or two less pages. This can add up - e.g. if you have 10
daemons blocking in poll/select you save 40KB of memory.
I did a patch for this long ago, but it was never applied. This version is
a reimplementation of the old patch that tries to be less intrusive. I
only did the minimal changes needed for the stack allocation.
The cut off point before external memory is allocated is currently at
832bytes. The system calls always allocate this much memory on the stack.
These 832 bytes are divided into 256 bytes frontend data (for the select
bitmaps of the pollfds) and the rest of the space for the wait queues used
by the low level drivers. There are some extreme cases where this won't
work out for select and it falls back to allocating memory too early -
especially with very sparse large select bitmaps - but the majority of
processes who only have a small number of file descriptors should be ok.
[TBD: 832/256 might not be the best split for select or poll]
I suspect more optimizations might be possible, but they would be more
complicated. One way would be to cache the select/poll context over
multiple system calls because typically the input values should be similar.
Problem is when to flush the file descriptors out though.
Signed-off-by: Andi Kleen <ak@suse.de> Cc: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Cox [Tue, 28 Mar 2006 09:56:31 +0000 (01:56 -0800)]
[PATCH] Small fixes backported to old IDE SiS driver
Some quick backport bits from the libata PATA work to fix things found in
the sis driver. The piix driver needs some fixes too but those are way to
large and need someone working on old IDE with time to do them.
This patch fixes the case where random bits get loaded into SIS timing
registers according to the description of the correct behaviour from
Vojtech Pavlik. It also adds the SiS5517 ATA16 chipset which is not
currently supported by the driver. Thanks to Conrad Harriss for loaning me
the machine with the 5517 chipset.
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eric Sesterhenn [Tue, 28 Mar 2006 09:56:24 +0000 (01:56 -0800)]
[PATCH] Change dash2underscore() return value to char
Since dash2underscore() just operates and returns chars, I guess its safe
to change the return value to a char. With my .config, this reduces its
size by 5 bytes.
text data bss dec hex filename
4155 152 0 4307 10d3 params.o.orig
4150 152 0 4302 10ce params.o
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brian Rogan [Tue, 28 Mar 2006 09:56:20 +0000 (01:56 -0800)]
[PATCH] Add oprofile_add_ext_sample
On ppc64 we look at a profiling register to work out the sample address and
if it was in userspace or kernel.
The backtrace interface oprofile_add_sample does not allow this. Create
oprofile_add_ext_sample and make oprofile_add_sample use it too.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: Philippe Elie <phil.el@wanadoo.fr> Cc: John Levon <levon@movementarian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Tue, 28 Mar 2006 09:56:20 +0000 (01:56 -0800)]
[PATCH] symversion warning fix
gcc-4.2:
kernel/module.c: In function '__find_symbol':
kernel/module.c:158: warning: the address of '__start___kcrctab', will always evaluate as 'true'
kernel/module.c:165: warning: the address of '__start___kcrctab_gpl', will always evaluate as 'true'
kernel/module.c:182: warning: the address of '__start___kcrctab_gpl_future', will always evaluate as 'true'
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Tue, 28 Mar 2006 09:56:19 +0000 (01:56 -0800)]
[PATCH] capi: register_chrdev() fix
If the user specified `major=0' (odd thing to do), capi.c will use dynamic
allocation. We need to pick up that major for subsequent unregister_chrdev().
Paul Fulghum [Tue, 28 Mar 2006 09:56:16 +0000 (01:56 -0800)]
[PATCH] synclink_gt: remove uneeded async code
Remove code in async receive handling that serves no purpose with new tty
receive buffering. Previously this code tried to free up receive buffer
space, but now does nothing useful while making expensive calls.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kyle McMartin [Tue, 28 Mar 2006 09:56:11 +0000 (01:56 -0800)]
[PATCH] Decrapify asm-generic/local.h
Now that Christoph Lameter's atomic_long_t support is merged in mainline,
might as well convert asm-generic/local.h to use it, so the same code can
be used for both sizes of 32 and 64-bit unsigned longs.
akpm sayeth:
Q:
Is there any particular reason why these routines weren't simply
implemented with local_save/restore_flags, if they are only meant to
guarantee atomicity to the local cpu? I'm sure on most platforms this
would be more efficient than using an atomic...
A:
The whole _point_ of local_t is to avoid local_irq_disable(). It's
designed to exploit the fact that many CPUs can do incs and decs in a way
which is atomic wrt local interrupts, but not atomic wrt SMP.
But this patch makes sense, because asm-generic/local.h is just a fallback
implementation for architectures which either cannot perform these
local-irq-atomic operations, or its maintainers haven't yet got around to
implementing them.
We need more work done on local_t in the 2.6.17 timeframe - they're defined as
unsigned long, but some architectures implement them as signed long.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org> Cc: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Matt Mackall [Tue, 28 Mar 2006 09:56:05 +0000 (01:56 -0800)]
[PATCH] RTC: Remove RTC UIP synchronization on ARM
Signed-off-by: Matt Mackall <mpm@selenic.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Matt Mackall [Tue, 28 Mar 2006 09:55:58 +0000 (01:55 -0800)]
[PATCH] RTC: Remove RTC UIP synchronization on x86
Reading the CMOS clock on x86 and some other arches currently takes up to one
second because it synchronizes with the CMOS second tick-over. This delay
shows up at boot time as well a resume time.
This is the currently the most substantial boot time delay for machines that
are working towards instant-on capability. Also, a quick back of the envelope
calculation (.5sec * 2M users * 1 boot a day * 10 years) suggests it has cost
Linux users in the neighborhood of a million man-hours.
..from which the consensus seems to be that it's no longer desirable.
In my view, there are basically four cases to consider:
1) networked, need precise walltime: use NTP
2) networked, don't need precise walltime: use NTP anyway
3) not networked, don't need sub-second precision walltime: don't care
4) not networked, need sub-second precision walltime:
get a network or a radio time source because RTC isn't good enough anyway
So this patch series simply removes the synchronization in favor of a simple
seqlock-like approach using the seconds value.
Note that for purposes of timer accuracy on wakeup, this patch will cause us
to fire timers up to one second late. But as the current timer resume code
will already sync once (or more!), it's no worse for short timers.
Signed-off-by: Matt Mackall <mpm@selenic.com> Cc: Andi Kleen <ak@muc.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: drop duplicate assignment in request_sock
[IPSEC]: Fix tunnel error handling in ipcomp6
Linus Torvalds [Mon, 27 Mar 2006 16:46:49 +0000 (08:46 -0800)]
Merge branch 'for-linus' of git://brick.kernel.dk/data/git/linux-2.6-block
* 'for-linus' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] Don't make debugfs depend on DEBUG_KERNEL
[PATCH] Fix blktrace compile with sysfs not defined
[PATCH] unused label in drivers/block/cciss.
[BLOCK] increase size of disk stat counters
[PATCH] blk_execute_rq_nowait-speedup
[PATCH] ide-cd: quiet down GPCMD_READ_CDVD_CAPACITY failure
[BLOCK] ll_rw_blk: kmalloc -> kzalloc conversion
[PATCH] kzalloc() conversion in drivers/block
[PATCH] update max_sectors documentation
Arjan van de Ven [Mon, 27 Mar 2006 09:18:20 +0000 (01:18 -0800)]
[PATCH] sem2mutex: drivers/md
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:18 +0000 (01:18 -0800)]
[PATCH] md: Fix md grow/size code to correctly find the maximum available space
An md array can be asked to change the amount of each device that it is using,
and in particular can be asked to use the maximum available space. This
currently only works if the first device is not larger than the rest. As
'size' gets changed and so 'fit' becomes wrong. So check if a 'fit' is
required early and don't corrupt it.
Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:17 +0000 (01:18 -0800)]
[PATCH] md: Remove bi_end_io call out from under a spinlock
raid5 overloads bi_phys_segments to count the number of blocks that the
request was broken in to so that it knows when the bio is completely handled.
Accessing this must always be done under a spinlock. In one case we also call
bi_end_io under that spinlock, which probably isn't ideal as bi_end_io could
be expensive (even though it isn't allowed to sleep).
So we reducde the range of the spinlock to just accessing bi_phys_segments.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:14 +0000 (01:18 -0800)]
[PATCH] md: Support suspending of IO to regions of an md array
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:13 +0000 (01:18 -0800)]
[PATCH] md: Split reshape handler in check_reshape and start_reshape
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:12 +0000 (01:18 -0800)]
[PATCH] md: Only checkpoint expansion progress occasionally
Instead of checkpointing at each stripe, only checkpoint when a new write
would overwrite uncheckpointed data. Block any write to the uncheckpointed
area. Arbitrarily checkpoint at least every 3Meg.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:11 +0000 (01:18 -0800)]
[PATCH] md: Checkpoint and allow restart of raid5 reshape
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to. The geometry allows for changing
chunksize, layout and level as well as number of devices.
When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array. For version-1, we use a feature bit for the same effect.
When starting an array we check for an incomplete reshape and restart the
reshape process if needed. If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:09 +0000 (01:18 -0800)]
[PATCH] md: Core of raid5 resize process
This patch provides the core of the resize/expand process.
sync_request notices if a 'reshape' is happening and acts accordingly.
It allocated new stripe_heads for the next chunk-wide-stripe in the target
geometry, marking them STRIPE_EXPANDING.
Then it finds which stripe heads in the old geometry can provide data needed
by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to
read all blocks on those stripes.
Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are
needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a
STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then
is written out and released.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:08 +0000 (01:18 -0800)]
[PATCH] md: Infrastructure to allow normal IO to continue while array is expanding
We need to allow that different stripes are of different effective sizes, and
use the appropriate size. Also, when a stripe is being expanded, we must
block any IO attempts until the stripe is stable again.
Key elements in this change are:
- each stripe_head gets a 'disk' field which is part of the key,
thus there can sometimes be two stripe heads of the same area of
the array, but covering different numbers of devices. One of these
will be marked STRIPE_EXPANDING and so won't accept new requests.
- conf->expand_progress tracks how the expansion is progressing and
is used to determine whether the target part of the array has been
expanded yet or not.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:07 +0000 (01:18 -0800)]
[PATCH] md: Allow stripes to be expanded in preparation for expanding an array
Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache
data structure.
This requires allocating new stripes in a new kmem_cache. If this succeeds,
we copy cache pages over and release the old stripes and kmem_cache.
We then allocate new pages. If that fails, we leave the stripe cache at it's
new size. It isn't worth the effort to shrink it back again.
Unfortuanately this means we need two kmem_cache names as we, for a short
period of time, we have two kmem_caches. So they are raid5/%s and
raid5/%s-alt
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:06 +0000 (01:18 -0800)]
[PATCH] md: Split disks array out of raid5 conf structure so it is easier to grow
The remainder of this batch implements raid5 reshaping. Currently the only
shape change that is supported is added a device, but it is envisioned that
changing the chunksize and layout will also be supported, as well as changing
the level (e.g. 1->5, 5->6).
The reshape process naturally has to move all of the data in the array, and so
should be used with caution. It is believed to work, and some testing does
support this, but wider testing would be great for increasing my confidence.
You will need a version of mdadm newer than 2.3.1 to make use of raid5 growth.
This is because mdadm need to take a copy of a 'critical section' at the
start of the array incase there is a crash at an awkward moment. On restart,
mdadm will restore the critical section and allow reshape to continue.
I hope to release a 2.4-pre by early next week - it still needs a little more
polishing.
This patch:
Previously the array of disk information was included in the raid5 'conf'
structure which was allocated to an appropriate size. This makes it awkward
to change the size of that array. So we split it off into a separate
kmalloced array which will require a little extra indexing, but is much easier
to grow.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:04 +0000 (01:18 -0800)]
[PATCH] md: Update status_resync to handle LARGE devices
status_resync - used by /proc/mdstat to report the status of a resync, assumes
that device sizes will always fit into an 'unsigned long' This is no longer
the case...
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Mon, 27 Mar 2006 09:18:03 +0000 (01:18 -0800)]
[PATCH] md: Fix the 'failed' count for version-0 superblocks
We are counting failed devices twice, once of the device that is failed, and
once for the hole that has been left in the array. Remove the former so
'failed' matches 'missing'. Storing these counts in the superblock is a bit
silly anyway....
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jun'ichi Nomura [Mon, 27 Mar 2006 09:17:58 +0000 (01:17 -0800)]
[PATCH] dm/md dependency tree in sysfs: md to use bd_claim_by_disk
Use bd_claim_by_disk.
Following symlinks are created if md0 is built from sda and sdb
/sys/block/md0/slaves/sda --> /sys/block/sda
/sys/block/md0/slaves/sdb --> /sys/block/sdb
/sys/block/sda/holders/md0 --> /sys/block/md0
/sys/block/sdb/holders/md0 --> /sys/block/md0
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Cc: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jun'ichi Nomura [Mon, 27 Mar 2006 09:17:57 +0000 (01:17 -0800)]
[PATCH] dm/md dependency tree in sysfs: bd_claim_by_kobject
Adding bd_claim_by_kobject() function which takes kobject as additional
signature of holder device and creates sysfs symlinks between holder device
and claimed device. bd_release_from_kobject() is a counterpart of
bd_claim_by_kobject.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Cc: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Darrick J. Wong [Mon, 27 Mar 2006 09:17:54 +0000 (01:17 -0800)]
[PATCH] dm store geometry
Allow drive geometry to be stored with a new DM_DEV_SET_GEOMETRY ioctl.
Device-mapper will now respond to HDIO_GETGEO. If the geometry information is
not available, zero will be returned for all of the parameters.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mike Anderson [Mon, 27 Mar 2006 09:17:54 +0000 (01:17 -0800)]
[PATCH] dm table: store md
Store an up-pointer to the owning struct mapped_device in every table when it
is created.
Access it with:
struct mapped_device *dm_table_get_md(struct dm_table *t)
Tables linked to md must be destroyed before the md itself.
Signed-off-by: Mike Anderson <andmike@us.ibm.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mike Anderson [Mon, 27 Mar 2006 09:17:52 +0000 (01:17 -0800)]
[PATCH] dm: store md name
The patch stores a printable device number in struct mapped_device for use in
warning messages and with a proposed netlink interface.
Signed-off-by: Mike Anderson <andmike@us.ibm.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jun'ichi Nomura [Mon, 27 Mar 2006 09:17:51 +0000 (01:17 -0800)]
[PATCH] dm flush queue EINTR
If dm_suspend() is cancelled, bios already added to the deferred list need to
be submitted. Otherwise they remain 'in limbo' until there's a dm_resume().
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before removing a snapshot, wait for the completion of any kcopyd jobs using
it.
Do this by maintaining a count (nr_jobs) of how many outstanding jobs each
kcopyd_client has.
The snapshot destructor first unregisters the snapshot so that no new kcopyd
jobs (created by writes to the origin) will reference that particular
snapshot. kcopyd_client_destroy() is now run next to wait for the completion
of any outstanding jobs before the snapshot exception structures (that those
jobs reference) are freed.
Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6-omap-h63xx.git / log