Phil Sutter [Mon, 19 Jan 2009 22:42:52 +0000 (23:42 +0100)]
MIPS: RB532: Move dev3 init code to devices.c
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Phil Sutter [Mon, 19 Jan 2009 22:42:51 +0000 (23:42 +0100)]
MIPS: RB532: Fix set_latch_u5()
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Phil Sutter [Thu, 15 Jan 2009 14:41:44 +0000 (15:41 +0100)]
MIPS: RB532: Use driver_data instead of platform_data
As the korina ethernet driver uses platform_get_drvdata() to extract the
driver specific data from the platform device, driver_data has to be
used here.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Auto-detection works just fine, so use it instead of specifying the type
manually. Also define a platform device for the uart, as suggested by
David Daney.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the pata-rb532-cf driver calls gpio_direction_input(), the calls to
rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since
the alternate function is automatically being disabled when changing the
GPIO pin direction.
The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being
done by the IRQ initialisation of pata-rb532-cf.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Phil Sutter [Fri, 28 Nov 2008 19:46:09 +0000 (20:46 +0100)]
MIPS: RB532: Auto disable GPIO alternate function
When a driver calls gpio_set_direction_{input,output}(), it obviously
doesn't want the alternate function for that pin to be active (as the
direction would not matter in that case). This patch ensures alternate
function is disabled when the direction is being changed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Phil Sutter [Fri, 28 Nov 2008 19:45:10 +0000 (20:45 +0100)]
MIPS: RB532: Add set_type() function to IRQ struct.
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.
The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.
As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)
To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().
After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Phil Sutter [Tue, 11 Nov 2008 23:09:30 +0000 (00:09 +0100)]
MIPS: RB532: Fix bit swapping in rb532_set_bit()
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Mon, 5 Jan 2009 23:29:58 +0000 (15:29 -0800)]
MIPS: Read watch registers with interrupts disabled.
If a context switch occurred between the watch exception and reading the
watch registers, it would be possible for the new process to corrupt their
state. Enabling interrupts only after the watch registers are read avoids
this race.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 28 Jan 2009 17:48:40 +0000 (17:48 +0000)]
MIPS: IP27: Switch from DMA_IP27 to DMA_COHERENT
The special IP27 DMA code selected by DMA_IP27 has been removed a while
ago turning DMA_IP27 into almost a nop. Also fixup the broken logic of
its last users memcpy.S and memcpy-inatomic.s.
Ralf Baechle [Mon, 12 Jan 2009 00:52:18 +0000 (00:52 +0000)]
MIPS: atomic_*(): Change type of intermediate variables.
This shaves of 1912 bytes of an IP27 defconfig kernel and avoids
unexpected overflow behaviour in atomic_sub_if_positive. Apply the same
changes to the atomic64_* functions for consistency.
Linus Torvalds [Fri, 30 Jan 2009 19:37:22 +0000 (11:37 -0800)]
Allow opportunistic merging of VM_CAN_NONLINEAR areas
Commit de33c8db5910cda599899dd431cc30d7c1018cbf ("Fix OOPS in
mmap_region() when merging adjacent VM_LOCKED file segments") unified
the vma merging of anonymous and file maps to just one place, which
simplified the code and fixed a use-after-free bug that could cause an
oops.
But by doing the merge opportunistically before even having called
->mmap() on the file method, it now compares two different 'vm_flags'
values: the pre-mmap() value of the new not-yet-formed vma, and previous
mappings of the same file around it.
And in doing so, it refused to merge the common file case, which adds a
marker to say "I can be made non-linear".
This fixes it by just adding a set of flags that don't have to match,
because we know they are ok to merge. Currently it's only that single
VM_CAN_NONLINEAR flag, but at least conceptually there could be others
in the future.
Reported-and-acked-by: Hugh Dickins <hugh@veritas.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 30 Jan 2009 16:54:29 +0000 (08:54 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Remove bogus BUG() check in ext4_bmap()
ext4: Fix building with EXT4FS_DEBUG
ext4: Initialize the new group descriptor when resizing the filesystem
ext4: Fix ext4_free_blocks() w/o a journal when files have indirect blocks
jbd2: On a __journal_expect() assertion failure printk "JBD2", not "EXT3-fs"
ext3: Add sanity check to make_indexed_dir
ext4: Add sanity check to make_indexed_dir
ext4: only use i_size_high for regular files
ext4: fix wrong use of do_div
Linus Torvalds [Fri, 30 Jan 2009 16:46:42 +0000 (08:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: Allow RT requests to pre-empt ongoing BE timeslice
block: add sysfs file for controlling io stats accounting
Mark mandatory elevator functions in the biodoc.txt
include/linux: Add bsg.h to the Kernel exported headers
block: silently error an unsupported barrier bio
block: Fix documentation for blkdev_issue_flush()
block: add bio_rw_flagged() for testing bio->bi_rw
block: seperate bio/request unplug and sync bits
block: export SSD/non-rotational queue flag through sysfs
Fix small typo in bio.h's documentation
block: get rid of the manual directory counting in blktrace
block: Allow empty integrity profile
block: Remove obsolete BUG_ON
block: Don't verify integrity metadata on read error
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tulip: fix 21142 with 10Mbps without negotiation
drivers/net/skfp: if !capable(CAP_NET_ADMIN): inverted logic
gianfar: Fix Wake-on-LAN support
smsc911x: timeout reaches -1
smsc9420: fix interrupt signalling test failures
ucc_geth: Change uec phy id to the same format as gianfar's
wimax: fix build issue when debugfs is disabled
netxen: fix memory leak in drivers/net/netxen_nic_init.c
tun: Add some missing TUN compat ioctl translations.
ipv4: fix infinite retry loop in IP-Config
net: update documentation ip aliases
net: Fix OOPS in skb_seq_read().
net: Fix frag_list handling in skb_seq_read
netxen: revert jumbo ringsize
ath5k: fix locking in ath5k_config
cfg80211: print correct intersected regulatory domain
cfg80211: Fix sanity check on 5 GHz when processing country IE
iwlwifi: fix kernel oops when ucode DMA memory allocation failure
rtl8187: Fix error in setting OFDM power settings for RTL8187L
mac80211: remove Michael Wu as maintainer
...
Divyesh Shah [Fri, 30 Jan 2009 11:46:41 +0000 (12:46 +0100)]
cfq-iosched: Allow RT requests to pre-empt ongoing BE timeslice
This patch adds the ability to pre-empt an ongoing BE timeslice when a RT
request is waiting for the current timeslice to complete. This reduces the
wait time to disk for RT requests from an upper bound of 4 (current value
of cfq_quantum) to 1 disk request.
Applied Jens' suggeested changes to avoid the rb lookup and use !cfq_class_rt()
and retested.
Latency(secs) for the RT task when doing sequential reads from 10G file.
| only RT | RT + BE | RT + BE + this patch
small (512 byte) reads | 143 | 163 | 145
large (1Mb) reads | 142 | 158 | 146
Signed-off-by: Divyesh Shah <dpshah@google.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Mark mandatory elevator functions in the biodoc.txt
biodoc.txt mentions that elevator functions marked with * are mandatory, but
no function is marked with *. Mark the 3 functions which should be
implemented by any io scheduler.
Boaz Harrosh [Mon, 19 Jan 2009 09:37:38 +0000 (10:37 +0100)]
include/linux: Add bsg.h to the Kernel exported headers
bsg.h in current form is perfectly suitable for user-mode
consumption. It is needed together with scsi/sg.h for applications
that want to interface with the bsg driver.
Currently the few projects that use it would copy it over into
the projects. But that is not acceptable for projects that need
to provide source and devel packages for distros.
This should also be submitted to stable 2.6.28 and 2.6.27 since bsg had
a stable API since these Kernels and distro users will need the header
for these kernels a swell
Jens Axboe [Tue, 6 Jan 2009 08:21:49 +0000 (09:21 +0100)]
block: add bio_rw_flagged() for testing bio->bi_rw
The existing functions for checking bio->bi_rw are badly named. So lets
mirror what we do for bio->bi_flags testing, use a properly named
function so that it's immediately obvious what is being tested.
Maintain compatability names for the old macros, eventually we'll get
rid of these.
block: export SSD/non-rotational queue flag through sysfs
For some devices (i.e. CFA ATA) we can't reliably detect whether
the device is of rotational or non-rotational type so we need to
leave the final decision about this setting to the user-space.
As a bonus do a minor CodingStyle fixup in queue_nomerges_store().
Allow a block device to allocate and register an integrity profile
without providing a template. This allows DM to preallocate a profile
to avoid deadlocks during table reconfiguration.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Theodore Ts'o [Fri, 30 Jan 2009 05:00:24 +0000 (00:00 -0500)]
ext4: Remove bogus BUG() check in ext4_bmap()
The code to support journal-less ext4 operation added a BUG to
ext4_bmap() which fired if there was no journal and the
EXT4_STATE_JDATA bit was set in the i_state field. This caused
running the filefrag program (which uses the FIMBAP ioctl) to trigger
a BUG().
The EXT4_STATE_JDATA bit is only used for ext4_bmap(), and it's
harmless for the bit to be set. We could add a check in
__ext4_journalled_writepage() and ext4_journalled_write_end() to only
set the EXT4_STATE_JDATA bit if the journal is present, but that adds
an extra test and jump instruction. It's easier to simply remove the
BUG check.
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: make sure we allocate enough storage for socket address
[CIFS] Make socket retry timeouts consistent between blocking and nonblocking cases
[CIFS] some cleanup to dir.c prior to addition of posix_open
[CIFS] revalidate parent inode when rmdir done within that directory
[CIFS] Rename md5 functions to avoid collision with new rt modules
cifs: turn smb_send into a wrapper around smb_sendv
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
breaks build like the following, in both cases when CONFIG_DMI set or not.
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
sata_sil.c should include dmi.h
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teemu Likonen [Fri, 30 Jan 2009 00:28:16 +0000 (16:28 -0800)]
Documentation: update CodingStyle tips for Emacs users
With the previous Emacs tips example the kernel style was made available
for files in the kernel-tree only. This patch updates the tip to add a
separate cc-mode indent style ("linux-tabs-only"). This makes it easy to
switch between different indent styles and also makes the kernel style
easily available for any filetype mode (c++, awk, ...) that is managed
by the Emacs cc-mode.
Signed-off-by: Teemu Likonen <tlikonen@iki.fi> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 30 Jan 2009 00:28:02 +0000 (16:28 -0800)]
Documentation: move DMA-mapping.txt to Doc/PCI/
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver-core: fix kernel-doc parameter name
UIO: Add missing documentation of features added recently
Sync patch for jp_JP/stable_kernel_rules.txt
Linus Torvalds [Fri, 30 Jan 2009 02:13:22 +0000 (18:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: OMAP: Initialize XCCR and RCCR registers in McBSP DAI driver
ASoC: Fix null string usage with WM8753 DAIs
ALSA: hda - add another MacBook Pro 4, 1 subsystem ID
ALSA: hda - Fix compile warning with CONFIG_SND_JACK=n
ALSA: hda - Add quirk for HP DV6700 laptop
ALSA: hda - Fix PCM reference NID for STAC/IDT analog outputs
Linus Torvalds [Fri, 30 Jan 2009 02:11:02 +0000 (18:11 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: document difference between hid_blacklist and hid_ignore_list
HID: add antec-branded soundgraph imon devices to blacklist
HID: fix reversed logic in disconnect testing of hiddev
HID: adjust report descriptor fixup for MS 1028 receiver
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix a memory leak with the lg object during launcher close
lguest: disable the FORTIFY for lguest.
lguest: typos fix
Linus Torvalds [Fri, 30 Jan 2009 02:09:41 +0000 (18:09 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: add workarounds for 2nd and 3rd generation iPods
firewire: sbp2: add workarounds for 2nd and 3rd generation iPods
firewire: sbp2: fix DMA mapping leak on the failure path
firewire: sbp2: define some magic numbers as macros
firewire: sbp2: fix payload limit at S1600 and S3200
ieee1394: sbp2: don't assume zero model_id or firmware_revision if there is none
ieee1394: sbp2: fix payload limit at S1600 and S3200
ieee1394: sbp2: update a help string
ieee1394: support for speeds greater than S800
firewire: core: optimize card shutdown
ieee1394: ohci1394: increase AT req. retries, fix ack_busy_X from Panasonic camcorders and others
firewire: ohci: increase AT req. retries, fix ack_busy_X from Panasonic camcorders and others
firewire: ohci: change "context_stop: still active" log message
firewire: keep highlevel drivers attached during brief connection loss
firewire: unnecessary BM delay after generation rollover
firewire: insist on successive self ID complete events
Davide Libenzi [Thu, 29 Jan 2009 22:25:26 +0000 (14:25 -0800)]
epoll: drop max_user_instances and rely only on max_user_watches
Linus suggested to put limits where the money is, and max_user_watches
already does that w/out the need of max_user_instances. That has the
advantage to mitigate the potential DoS while allowing pretty generous
default behavior.
Allowing top 4% of low memory (per user) to be allocated in epoll watches,
we have:
Frans Pop [Thu, 29 Jan 2009 22:25:25 +0000 (14:25 -0800)]
hp-wmi: set initial docking state
If the initial state is not set when the input device is set up, the first
docking event after the module is loaded will be lost.
Signed-off-by: Frans Pop <elendil@planet.nl> Acked-by: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bharath Ramesh [Thu, 29 Jan 2009 22:25:24 +0000 (14:25 -0800)]
hwmon: applesmc: add support for MacPro 3 temperature sensors
MacPro 3 have more temperature sensors than the previous MacPro's also the
sensor THTG has been removed. This patch add supports for the newer
temperature sensors in the MacPro3.
Signed-off-by: Bharath Ramesh <bramesh@vt.edu> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Menage [Thu, 29 Jan 2009 22:25:22 +0000 (14:25 -0800)]
cgroup: fix root_count when mount fails due to busy subsystem
root_count was being incremented in cgroup_get_sb() after all error
checking was complete, but decremented in cgroup_kill_sb(), which can be
called on a superblock that we gave up on due to an error. This patch
changes cgroup_kill_sb() to only decrement root_count if the root was
previously linked into the list of roots.
Signed-off-by: Paul Menage <menage@google.com> Tested-by: Serge Hallyn <serue@us.ibm.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Thu, 29 Jan 2009 22:25:21 +0000 (14:25 -0800)]
cgroups: fix lock inconsistency in cgroup_clone()
I fixed a bug in cgroup_clone() in Linus' tree in commit 7b574b7
("cgroups: fix a race between cgroup_clone and umount") without noticing
there was a cleanup patch in -mm tree that should be rebased (now commit 104cbd5, "cgroups: use task_lock() for access tsk->cgroups safe in
cgroup_clone()"), thus resulted in lock inconsistency.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ivan Kokshaysky [Thu, 29 Jan 2009 22:25:20 +0000 (14:25 -0800)]
alpha: fix the BUG() macro
The commit "alpha: teach the compiler that BUG doesn't return"
(ed6b9b97f42c091630335bfb71a2931e6f86388b) moved the asm code into inline
function which takes __FILE__ and __LINE__ as arguments. This violates
asm constrains there ("i" - an immediate operand with constant value), so
that compile may result in warning or error, depending on compiler
version.
Just adding an infinite loop to the BUG() is sufficient.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Richard Henderson <rth@twiddle.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ivan Kokshaysky [Thu, 29 Jan 2009 22:25:19 +0000 (14:25 -0800)]
alpha: compile fixes
- jensen build: fix conflicting declarations for pci_alloc_consistent()
and undefined virt_to_phys();
- SMP: arch/alpha/kernel/smp.c:124: warning: passing argument 2
of '__cpu_test_and_set' discards qualifiers from pointer target type
Interestingly, this only happens with gcc-4.2; gcc <= 4.1 and gcc-4.3
are OK. Fixed with extra assignment.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Richard Henderson <rth@twiddle.net> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frans Pop [Thu, 29 Jan 2009 22:25:14 +0000 (14:25 -0800)]
hp-wmi: fix regressions caused by missing if statement
Error was introduced in commit fe8e4e039dc3 ("hp-wmi: handle
rfkill_register() failure").
Signed-off-by: Frans Pop <elendil@planet.nl> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Matthew Garrett <mjg@redhat.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lifetime of struct cgroup and struct mem_cgroup is different and
mem_cgroup has its own reference count for handling references from
swap_cgroup.
This causes strange problem that the parent mem_cgroup dies while child
mem_cgroup alive, and this problem causes a bug in case of
use_hierarchy==1 because res_counter_uncharge climbs up the tree.
This patch is for avoiding it by getting the parent at create, and putting
it at freeing.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reviewed-by; KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelyanov <xemul@openvz.org> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masami Hiramatsu [Thu, 29 Jan 2009 22:25:08 +0000 (14:25 -0800)]
kprobes: fix module compilation error with CONFIG_KPROBES=n
Define kprobes related data structures even if CONFIG_KPROBES is not set.
This fixes compilation errors which occur if CONFIG_KPROBES is not set, in
kprobe using modules.
[akpm@linux-foundation.org: fix build for non-kprobes-supporting architectures] Reviewed-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Holt [Thu, 29 Jan 2009 22:25:07 +0000 (14:25 -0800)]
sgi-xpc: fix up stale DBUG_ON statements
Clean up the stale DBUG_ON checks and add a couple new ones.
Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Holt [Thu, 29 Jan 2009 22:25:07 +0000 (14:25 -0800)]
sgi-xpc: Remove NULL pointer dereference.
If the bte copy fails, the attempt to retrieve payloads merely returns a
null pointer deref and not NULL as was expected.
Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Holt [Thu, 29 Jan 2009 22:25:06 +0000 (14:25 -0800)]
sgi-xpc: ensure flags are updated before bte_copy
The clearing of the msg->flags needs a barrier between it and the notify
of the channel threads that the messages are cleaned and ready for use.
Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 30 Jan 2009 01:46:42 +0000 (17:46 -0800)]
Fix OOPS in mmap_region() when merging adjacent VM_LOCKED file segments
As of commit ba470de43188cdbff795b5da43a1474523c6c2fb ("map: handle
mlocked pages during map, remap, unmap") we now use the 'vma' variable
at the end of mmap_region() to handle the page-in of newly mapped
mlocked pages.
However, if we merged adjacent vma's together, the vma we're using may
be stale. We historically consciously avoided using it after the merge
operation, but that got overlooked when redoing the locked page
handling.
This commit simplifies mmap_region() by doing any vma merges early,
avoiding the issue entirely, and 'vma' will always be valid. As pointed
out by Hugh Dickins, this depends on any drivers that change the page
offset of flags to have set one of the VM_SPECIAL bits (so that they
cannot trigger the early merge logic), but that's true in general.
Reported-and-tested-by: Maksim Yevmenkin <maksim.yevmenkin@gmail.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network. It used
to work in 2.4 kernels. Fix that. Tested on a 21142 Rev 0x11.
Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.
This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.
A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Fri, 30 Jan 2009 01:30:00 +0000 (17:30 -0800)]
smsc911x: timeout reaches -1
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc9420 performs an interrupt signalling test when the interface is
brought up. The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.
This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiying Wang [Fri, 30 Jan 2009 01:28:04 +0000 (17:28 -0800)]
ucc_geth: Change uec phy id to the same format as gianfar's
The commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Actually I did some testing and added a few printks and found that the
st->cur_skb->data was 0 and hence the ptr used by iscsi_tcp was null.
This caused the kernel panic.
I enabled the debug_tcp and with a few printks found that the code did
not go to the next_skb label and could find that the sequence being
followed was this -
Reversing the two conditions the attached patch fixes the issue for me
on top of Herbert's patches.
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 30 Jan 2009 00:05:19 +0000 (16:05 -0800)]
netxen: revert jumbo ringsize
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
Bob Copeland [Thu, 22 Jan 2009 13:44:16 +0000 (08:44 -0500)]
ath5k: fix locking in ath5k_config
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6-omap-h63xx.git / log