Arjan van de Ven [Tue, 29 Nov 2005 08:43:42 +0000 (09:43 +0100)]
[PATCH] USB: mark various usb tables const
patch below marks various USB tables and variables as const so that they
end up in .rodata section and don't cacheline share with things that get
written to. For the non-array variables it also allows gcc to optimize
more.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as614) makes a small change to the part of the hub driver
responsible for remote wakeup of root hubs. When these wakeups occur
the driver is suspended, and in case the resume fails the driver should
remain suspended -- it shouldn't try to proceed with its normal
processing.
This will hardly ever matter in normal use, but it did crop up while I
was debugging a different problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 29 Nov 2005 17:08:15 +0000 (12:08 -0500)]
[PATCH] USB Gadget: dummy_hcd: updates to hcd->state
This patch (as613) moves the updates to hcd->state in the dummy_hcd
driver to where they now belong. It also uses the new
HC_FLAG_HW_ACCESSIBLE flag in a way that simulates a real PCI
controller, and it adds checks for attempts to resume the bus while the
controller is suspended or to suspend the controller while the bus is
active.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 29 Nov 2005 17:04:24 +0000 (12:04 -0500)]
[PATCH] USB Gadget: file_storage: remove "volatile" declarations
This patch (as612) removes the "volatile" declarations from the
file-storage gadget. It turns out that they aren't needed for anything
much; adding a few memory barriers does a sufficient job.
The patch also removes a wait_queue. Not much point having a queue when
only one task is ever going to be on it!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Chris Humbert [Mon, 28 Nov 2005 17:29:23 +0000 (09:29 -0800)]
[PATCH] USB: don't allocate dma pools for PIO HCDs
USB: don't allocate dma pools for PIO HCDs
hcd_buffer_alloc() and hcd_buffer_free() have a similar dma_mask
check and revert to kmalloc()/kfree(), but hcd_buffer_create()
doesn't check dma_mask and allocates unused dma pools.
Signed-off-by: Chris Humbert <mahadri-kernel@drigon.com> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some versions of the controller seem to put multiple report packet into a
single urb. also it can happen that a packet is split across multiple urbs.
unpatched you get a jumpy cursor on some screens.
the patch does:
- handle multiple packets per urb
- handle packets split across multiple urb
- check packet type
- cleanups
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race-condition in usb-serial driver that can be triggered if
a processes does 'port->tty->driver_data = NULL' in serial_close() while
other processes is in kernel-space about to call serial_ioctl() on the
same port.
This happens because a process can open the device while there is
another one closing it.
The patch below fixes that by adding a semaphore to ensure that no
process will open the device while another process is closing it.
Note that we can't use spinlocks here, since serial_open() and
serial_close() can sleep.
Alan Stern [Wed, 23 Nov 2005 17:09:52 +0000 (12:09 -0500)]
[PATCH] USB: Store port number in usb_device
This patch (as610) adds a field to struct usb_device to store the device's
port number. This allows us to remove several loops in the hub driver
(searching for a particular device among all the entries in the parent's
array of children).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 23 Nov 2005 17:03:12 +0000 (12:03 -0500)]
[PATCH] USB: Consider power budget when choosing configuration
This patch (as609) changes the way we keep track of power budgeting for
USB hubs and devices, and it updates the choose_configuration routine to
take this information into account. (This is something we should have
been doing all along.) A new field in struct usb_device holds the amount
of bus current available from the upstream port, and the usb_hub structure
keeps track of the current available for each downstream port.
Two new rules for configuration selection are added:
Don't select a self-powered configuration when only bus power
is available.
Don't select a configuration requiring more bus power than is
available.
However the first rule is #if-ed out, because I found that the internal
hub in my HP USB keyboard claims that its only configuration is
self-powered. The rule would prevent the configuration from being chosen,
leaving the hub & keyboard unconfigured. Since similar descriptor errors
may turn out to be fairly common, it seemed wise not to include a rule
that would break automatic configuration unnecessarily for such devices.
The second rule may also trigger unnecessarily, although this should be
less common. More likely it will annoy people by sometimes failing to
accept configurations that should never have been chosen in the first
place.
The patch also changes usbcore's reaction when no configuration is
suitable. Instead of raising an error and rejecting the device, now
the core will simply leave the device unconfigured. People can always
work around such problems by installing configurations manually through
sysfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk [Sun, 20 Nov 2005 22:56:11 +0000 (23:56 +0100)]
[PATCH] USB: small cleanups
This patch contains the following cleanups:
- make needlessly global functions static
- every file should #include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Nov 2005 16:58:07 +0000 (11:58 -0500)]
[PATCH] USB: Fix locking for USB suspend/resume
The earlier USB locking updates didn't touch the suspend/resume
routines. They need updating as well, since now the caller holds the
device semaphore. This patch (as608) makes the necessary changes. It
also adds a line to store the correct power state when a device is
resumed, something which was unaccountably missing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 18 Nov 2005 17:06:34 +0000 (12:06 -0500)]
[PATCH] USB: Disconnect children during hub unbind
This patch (as606b) is an updated version of my earlier patch to
disconnect children from a hub device when the hub driver is unbound.
Thanks to the changes in the driver core locking, we now know that the
entire hub device (and not just the interface) is locked whenever the
hub driver's disconnect method runs. Hence it is safe to disconnect the
child device structures immediately instead of deferring the job.
The earlier version of the patch neglected to disable the hub's ports.
We don't want to forget that; otherwise we'd end up with live devices
using addresses that have been recycled. This update adds the necessary
code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 17 Nov 2005 22:10:32 +0000 (17:10 -0500)]
[PATCH] USB: Remove USB private semaphore
This patch (as605) removes the private udev->serialize semaphore,
relying instead on the locking provided by the embedded struct device's
semaphore. The changes are confined to the core, except that the
usb_trylock_device routine now uses the return convention of
down_trylock rather than down_read_trylock (they return opposite values
for no good reason).
A couple of other associated changes are included as well:
Now that we aren't concerned about HCDs that avoid using the
hcd glue layer, usb_disconnect no longer needs to acquire the
usb_bus_lock -- that can be done by usb_remove_hcd where it
belongs.
Devices aren't locked over the same scope of code in
usb_new_device and hub_port_connect_change as they used to be.
This shouldn't cause any trouble.
Along with the preceding driver core patch, this needs a lot of testing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] USB: make registering a usb driver automatically set the module owner
This fixes the driver that forgot to set the module owner up. Now we
can remove the unneeded pointer from the usb driver structure. The idea
for how to do this was from Al Viro, who did this for the PCI drivers.
[PATCH] USB: allow usb drivers to disable dynamic ids
This lets drivers, like the usb-serial ones, disable the ability to add
ids from sysfs.
The usb-serial drivers are "odd" in that they are really usb-serial bus
drivers, not usb bus drivers, so the dynamic id logic will have to go
into the usb-serial bus core for those drivers to get that ability.
[PATCH] USB: add dynamic id functionality to USB core
Echo the usb vendor and product id to the "new_id" file in the driver's
sysfs directory, and then that driver will be able to bind to a device
with those ids if it is present.
Example:
echo 0557 2008 > /sys/bus/usb/drivers/foo_driver/new_id
adds the hex values 0557 and 2008 to the device id table for the foo_driver.
Note, usb-serial drivers do not currently work with this capability yet.
usb-storage also might have some oddities.
Pete Zaitcev [Sun, 23 Oct 2005 03:15:09 +0000 (20:15 -0700)]
[PATCH] USB: drivers/usb/storage/libusual
This patch adds a shim driver libusual, which routes devices between
usb-storage and ub according to the common table, based on unusual_devs.h.
The help and example syntax is in Kconfig.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 14 Nov 2005 16:45:38 +0000 (11:45 -0500)]
[PATCH] USB: central handling for host controllers that were reset during suspend/resume
This patch (as515b) adds a routine to usbcore to simplify handling of
host controllers that lost power or were reset during suspend/resume.
The new core routine marks all the child devices of the root hub as
NOTATTACHED and tells khubd to disconnect the device structures as soon
as possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 14 Nov 2005 17:16:30 +0000 (12:16 -0500)]
[PATCH] USB: dummy_hcd: rename variables
The recent platform_device update has reintroduced into dummy_hcd.c the
dreaded dev->dev syndrome. This harkens back to when an earlier version
of that driver included the unforgettable line:
dev->dev.dev.driver_data = dev;
This patch (as602) renames the platform_device variables to "pdev", in
the hope of reducing confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A.YOSHIYAMA [Tue, 15 Nov 2005 07:55:18 +0000 (09:55 +0200)]
[PATCH] USB: usb-net: new device ID passed through module parameter
adds new module parameter "devid" that points to a string with format
"device_name:vendor_id:device_id:flags". if provided at module load
time, this string is being parsed and a new entry is created in
usb_dev_id[] and pegasus_ids[] so the new device can later be recognized
by the probe routine. this might be helpful for someone who don't
know/wish to build new module/kernel, but want to use his new usb-to-eth
device that is not yet listed in pegasus.h
Petko Manolov [Tue, 15 Nov 2005 07:48:23 +0000 (09:48 +0200)]
[PATCH] USB: usb-net: removes redundant return
removes all redundant collecting of the return value from
get/set_registers() and suchlike. can't remember who put all of those
some time ago, but they doesn't make any sense to me. where needed only
a few references remained;
Alan Stern [Wed, 9 Nov 2005 21:59:56 +0000 (16:59 -0500)]
[PATCH] USB: file-storage gadget: Add reference count for children
This patch (as601) adds a proper reference count to the file-storage
gadget's main data structure, to keep track of references held by child
devices (LUNs in this case). Before this, the driver would wait for
each child to be released before unbinding.
While there's nothing really wrong with that (you can't create a hang by
doing "rmmod g_file_storage </sys/.../lun0/ro" since the open file will
prevent rmmod from running), the code might as well follow the standard
procedures. Besides, this shrinks the size of the structure by a few
words... :-)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 8 Nov 2005 04:45:20 +0000 (20:45 -0800)]
[PATCH] USB: hcd uses EXTRA_CFLAGS for -DDEBUG
This modifies the HCD builds to automatically "-DDEBUG" if
CONFIG_USB_DEBUG is selected. It's just a minor source code cleanup,
guaranteeing consistency.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 7 Nov 2005 23:34:41 +0000 (15:34 -0800)]
[PATCH] USB: wakeup flag updates (2/3) uhci-hcd
This makes UHCI stop using the HCD glue wakeup flags to report whether
the controller can wake the system. The existing code was wrong anyway;
having a PCI PM capability doesn't imply it reports PME# is supported.
I skimmed Intel's ICH7 datasheet and that basically says the wakeup
signaling gets routed only through ACPI registers. (On the other hand,
many VIA chips provide the PCI PM capabilities...) I think that doing
this correctly with UHCI is going to require the ACPI folk to associate
the /proc/acpi/wakeup identifiers (and wakeup enable/disable flags)
with the relevant /sys/devices/pci*/... devices.
From: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 23 Dec 2005 01:05:18 +0000 (17:05 -0800)]
[PATCH] USB: ehci fix driver model wakeup flags
On some systems, EHCI seems to be getting IRQs too early during driver
setup ... before the root hub is allocated, in particular, making trouble
for any code chasing down root hub pointers! In this case, it seems to
be safe to just ignore the root hub setting. Thanks to Rafael J. Wysocki
for getting this properly tested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 7 Nov 2005 23:24:46 +0000 (15:24 -0800)]
[PATCH] USB: EHCI updates (4/4) driver model wakeup flags
This teaches the EHCI driver to use the new driver model wakeup flags,
replacing the similar ones in the HCD glue. It also adds a workaround
for the current glitch whereby PCI init doesn't init the wakeup flags
from the PCI PM capabilities. (EHCI controllers don't worry about
legacy mode; the PCI PM capability would always do the job.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
matthieu castet [Mon, 7 Nov 2005 22:27:13 +0000 (23:27 +0100)]
[PATCH] USB: Eagle and ADI 930 usb adsl modem driver
A driver for USB ADSL modems based on the ADI eagle chipset using the
usb_atm infrastructure.
The managing part was taken from bsd ueagle driver, other parts were
written from scratch.
The driver uses the in-kernel firmware loader :
- to load a first usb firmware when the modem is in pre-firmware state
- to load the dsp firmware that are swapped in host memory.
- to load CMV (configuration and management variables) when the modem
boot. (We can't use options or sysfs for this as there many possible
values. See
https://mail.gna.org/public/eagleusb-dev/2005-04/msg00031.html for a
description of some)
- to load fpga code for 930 chipset.
The device had 4 endpoints :
* 2 for data (use by usbatm). The incoming
endpoint could be iso or bulk. The modem seems buggy and produce lot's
of atm errors when using it in bulk mode for speed > 3Mbps, so iso
endpoint is need for speed > 3Mbps. At the moment iso endpoint need a
patched usbatm library and for this reason is not included in this patch.
* One bulk endpoint for uploading dsp firmware
* One irq endpoint that notices the driver
- if we need to upload a page of the dsp firmware
- an ack for read or write CMV and the value (for the read case).
If order to make the driver cleaner, we design synchronous
(read|write)_cmv :
-send a synchronous control message to the modem
-wait for an ack or a timeout
-return the value if needed.
In order to run these synchronous usb messages we need a kernel thread.
The driver has been tested with sagem fast 800 modems with different
eagle chipset revision and with ADI 930 since April 2005.
Alan Stern [Thu, 3 Nov 2005 16:44:49 +0000 (11:44 -0500)]
[PATCH] USB: EHCI: fix conflation of buf == 0 with len == 0
When the ehci-hcd driver prepares a control URB, it tests for a
zero-length data stage by looking at the transfer_dma value instead of
the transfer_buffer_length. (In fact it does this even for non-control
URBs, which is an additional aspect of the same bug.)
However, under certain circumstances it's possible for transfer_dma to
be 0 while transfer_buffer_length is non-zero. This can happen when a
freshly allocated page (mapped to address 0 and marked Copy-On-Write,
but never written to) is used as the source buffer for an OUT transfer.
This patch (as598) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Olav Kongas [Thu, 3 Nov 2005 15:38:14 +0000 (17:38 +0200)]
[PATCH] USB: isp116x-hcd: cleanup
The attached patch makes a cleanup of isp116x-hcd. Most of the volume of
the patch comes from 2 sources: moving the code around to get rid of a
few function prototypes and reworking register dumping functions/macros.
Among other things, switched over from using procfs to debugfs.
Cleanup. The following changes were made:
- Rework register dumping code so it can be used for dumping
to both syslog and debugfs.
- Switch from procfs to debugfs..
- Die gracefully on Unrecoverable Error interrupt.
- Fix memory leak in isp116x_urb_enqueue(), if HC happens to
die in a narrow time window.
- Fix a 'sparce' warning (unnecessary cast).
- Report Devices Removable for root hub ports by default
(was Devices Permanently Attached).
- Move bus suspend/resume functions down in code to get rid of
a few function prototypes.
- A number of one-line cleanups.
- Add an entry to MAINTAINERS.
Olav Kongas [Fri, 28 Oct 2005 12:04:45 +0000 (15:04 +0300)]
[PATCH] USB: isp116x-hcd: support reiniting HC on resume
Until now the isp116x-hcd had no support to reinitialize the HC on
resume, if the controller lost its state during suspend. This patch,
generated against your Oct 26 git tree, adds that support. The patch is
basically the same as the one tested by Ivan Kalatchev, who reported the
problem, on 2.6.13.
Please apply,
Support reinitializing the isp116x host controller from scratch on
resume, if the controller has lost its state.
Signed-off-by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Richard Purdie [Sat, 12 Nov 2005 14:22:14 +0000 (14:22 +0000)]
[PATCH] USB: Add pxa27x OHCI PM functions
Add power management functions for the pxa27x USB OHCI host controller.
This is a totally rewritten version of the patch by Nicolas Pitre and
Todd Poynor which accounts for recent USB changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Richard Purdie [Sat, 12 Nov 2005 14:22:11 +0000 (14:22 +0000)]
[PATCH] USB: pxa27x OHCI - Separate platform code from main driver
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Nicolas Pitre <nico@cam.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
However, asm/param.h is sometimes used in userland (it is included
indirectly from <sys/param.h>), so your commit pollutes the userland
namespace with tons of CONFIG_FOO macros. This greatly confuses
software packages (such as BusyBox) which use CONFIG_FOO macros
themselves to control the inclusion of optional features.
After a short exchange, Christoph approved this patch
Some G5s still occasionally experience shutdowns due to overtemp
conditions despite the recent fix. After analyzing logs from such
machines, it appears that the overtemp code is a bit too quick at
shutting the machine down when reaching the critical temperature (tmax +
8) and doesn't leave the fan enough time to actually cool it down. This
happens if the temperature of a CPU suddenly rises too high in a very
short period of time, or occasionally on boot (that is the CPUs are
already overtemp by the time the driver loads).
This patches makes the code a bit more relaxed, leaving a few seconds to
the fans to do their job before kicking the machine shutown.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sun, 1 Jan 2006 01:00:29 +0000 (17:00 -0800)]
sysctl: make sure to terminate strings with a NUL
This is a slightly more complete fix for the previous minimal sysctl
string fix. It always terminates the returned string with a NUL, even
if the full result wouldn't fit in the user-supplied buffer.
The returned length is the full untruncated length, so that you can
tell when truncation has occurred.
Yi Yang [Fri, 30 Dec 2005 08:37:10 +0000 (16:37 +0800)]
[PATCH] Fix false old value return of sysctl
For the sysctl syscall, if the user wants to get the old value of a
sysctl entry and set a new value for it in the same syscall, the old
value is always overwritten by the new value if the sysctl entry is of
string type and if the user sets its strategy to sysctl_string. This
issue lies in the strategy being run twice if the strategy is set to
sysctl_string, the general strategy sysctl_string always returns 0 if
success.
Such strategy routines as sysctl_jiffies and sysctl_jiffies_ms return 1
because they do read and write for the sysctl entry.
The strategy routine sysctl_string return 0 although it actually read
and write the sysctl entry.
According to my analysis, if a strategy routine do read and write, it
should return 1, if it just does some necessary check but not read and
write, it should return 0, for example sysctl_intvec.
Signed-off-by: Yi Yang <yang.y.yi@gmail.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sat, 31 Dec 2005 01:18:53 +0000 (17:18 -0800)]
sysctl: don't overflow the user-supplied buffer with '\0'
If the string was too long to fit in the user-supplied buffer,
the sysctl layer would zero-terminate it by writing past the
end of the buffer. Don't do that.
Linus Torvalds [Fri, 30 Dec 2005 16:39:10 +0000 (08:39 -0800)]
Insanity avoidance in /proc
The old /proc interfaces were never updated to use loff_t, and are just
generally broken. Now, we should be using the seq_file interface for
all of the proc files, but converting the legacy functions is more work
than most people care for and has little upside..
But at least we can make the non-LFS rules explicit, rather than just
insanely wrapping the offset or something.
Erik Hovland [Fri, 30 Dec 2005 15:57:35 +0000 (15:57 +0000)]
[ARM] 3216/1: indent and typo in drivers/serial/pxa.c
Patch from Erik Hovland
This patch provides two changes. An indent is supplied for an if/else clause so that it is more readable. An acronym is incorrectly typed as UER when it should be IER.
Signed-off-by: Erik Hovland <erik@hovland.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jean Delvare [Thu, 29 Dec 2005 21:07:30 +0000 (22:07 +0100)]
[PATCH] Simplify the VIDEO_SAA7134_OSS Kconfig dependency line
Thanks to Roman Zippel for the suggestion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
[ Short explanation: Kconfig uses ternary math: n/m/y, and !m is m ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
that changed the GART VM start offset. It fixed some machines, but
seems to continually interact badly with some X versions.
Quoth Ben Herrenschmidt:
"So I think at this point, the best is that we keep the old bogus code
that at least is consistent with the bug in the server. I'm working on a
big patch to X that reworks the memory map stuff completely and fixes
those issues on the server side, I'll do a DRM patch matching this X fix
as well so that the memory map is only ever set in one place and with
what I hope is a correct algorithm..."
Anton Blanchard [Wed, 28 Dec 2005 23:46:29 +0000 (10:46 +1100)]
[PATCH] ppc64: htab_initialize_secondary cannot be marked __init
Sonny has noticed hotplug CPU on ppc64 is broken in 2.6.15-*. One of the
problems is that htab_initialize_secondary is called when a cpu is being
brought up, but it is marked __init.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Jones [Thu, 29 Dec 2005 01:01:04 +0000 (20:01 -0500)]
[PATCH] fix ia64 compile failure with gcc4.1
__get_unaligned creates a typeof the var its passed, and writes to it,
which on gcc4.1, spits out the following error:
drivers/char/vc_screen.c: In function 'vcs_write':
drivers/char/vc_screen.c:422: error: assignment of read-only variable 'val'
Signed-off-by: Dave Jones <davej@redhat.com>
[ The "right" fix would be to try to fix <asm-generic/unaligned.h>
but that's hard to do with the tools gcc gives us. So this
simpler patch is preferable -- Linus ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: fix compilation with CONFIG_MODE_TT disabled
Fix UML compilation when SKAS mode is disabled. Indeed, we were compiling
SKAS-only object files, which failed due to some SKAS-only headers being
excluded from the search path.
Thanks to the bug report from Pekka J Enberg.
Acked-by: Pekka J Enberg <penberg (at) cs ! helsinki ! fi> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Hostfs: update for new glibc - add missing symbol exports
Today, when compiling UML, I got warnings for two used unexported symbols:
readdir64 and truncate64. Indeed, my glibc headers are aliasing readdir to
readdir64 and truncate to truncate64 (and so on).
I'm then adding additional exports. Since I've no idea if the symbols where
always provided in the supported glibc's, I've added weak definitions too.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: hostfs - fix possible PAGE_CACHE_SHIFT overflows
Prevent page->index << PAGE_CACHE_SHIFT from overflowing.
There is a casting there, but was added without care, so it's at the wrong
place. Note the extra parens around the shift - "+" is higher precedence than
"<<", leading to a GCC warning which saved all us.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial removal of unused variable from this file - doesn't even change the
generated assembly code, in fact (gcc should trigger a warning for unused value
here).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't use printk() where "current_thread_info()" is crap.
Until when we switch to running on init_stack, current_thread_info() evaluates
to crap. Printk uses "current" at times (in detail, ¤t is evaluated with
CONFIG_DEBUG_SPINLOCK to check the spinlock owner task).
And this leads to random segmentation faults.
Exactly, what happens is that ¤t = *(current_thread_info()), i.e. round
down $esp and dereference the value. I.e. access the stack below $esp, which
causes SIGSEGV on a VM_GROWSDOWN vma (see arch/i386/mm/fault.c).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David S. Miller [Wed, 28 Dec 2005 21:27:04 +0000 (13:27 -0800)]
[SERMOUSE]: Sun mice speak 5-byte protocol too.
Noticed by Christophe Zimmerman, this explains the slow mouse movement
with 2.6.x kernels.
And checking the 2.4.x drivers/sbus/char/sunmouse.c driver shows we
always used a 5-byte protocol with Sun mice in the past. I have no
idea how the 3-byte thing got into the 2.6.x driver, but it's surely
wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Elmquist [Tue, 20 Dec 2005 21:25:19 +0000 (13:25 -0800)]
[TG3]: ethtool -d hangs PCIe systems
Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1). Retested. Problem remains fixed.
Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] Fix more radeon GART start calculation cases
As reported by Jules Villard <jvillard@ens-lyon.fr> and some others, the
recent GART aperture start reconfiguration causes problems on some
setups.
What I _think_ might be happening is that the X server is also trying to
muck around with the card memory map and is forcing it back into a wrong
setting that also happens to no longer match what the DRM wants to do
and blows up. There are bugs all over the place in that code (and still
some bugs in the DRM as well anyway).
This patch attempts to avoid that by using the largest of the 2 values,
which I think will cause it to behave as it used to for you and will
still fix the problem with machines that have an aperture size smaller
than the video memory.
David L Stevens [Tue, 27 Dec 2005 22:03:00 +0000 (14:03 -0800)]
[IPV6] mcast: Fix multiple issues in MLDv2 reports.
The below "jumbo" patch fixes the following problems in MLDv2.
1) Add necessary "ntohs" to recent "pskb_may_pull" check [breaks
all nonzero source queries on little-endian (!)]
2) Add locking to source filter list [resend of prior patch]
3) fix "mld_marksources()" to
a) send nothing when all queried sources are excluded
b) send full exclude report when source queried sources are
not excluded
c) don't schedule a timer when there's nothing to report
NOTE: RFC 3810 specifies the source list should be saved and each
source reported individually as an IS_IN. This is an obvious DOS
path, requiring the host to store and then multicast as many sources
as are queried (e.g., millions...). This alternative sends a full,
relevant report that's limited to number of sources present on the
machine.
4) fix "add_grec()" to send empty-source records when it should
The original check doesn't account for a non-empty source
list with all sources inactive; the new code keeps that
short-circuit case, and also generates the group header
with an empty list if needed.
5) fix mca_crcount decrement to be after add_grec(), which needs
its original value
These issues (other than item #1 ;-) ) were all found by Yan Zheng,
much thanks!
Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Kimdon [Tue, 27 Dec 2005 01:27:10 +0000 (17:27 -0800)]
[BR_NETFILTER]: Fix leak if skb traverses > 1 bridge
Call nf_bridge_put() before allocating a new nf_bridge structure and
potentially overwriting the pointer to a previously allocated one.
This fixes a memory leak which can occur when the bridge topology
allows for an skb to traverse more than one bridge.
Signed-off-by: David Kimdon <david.kimdon@devicescape.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Bottomley [Mon, 26 Dec 2005 15:58:49 +0000 (09:58 -0600)]
[PATCH] Fix Fibre Channel boot oops
The oops is characteristic of the underlying device being removed from
visibility before the class device, and sure enough we do device_del()
before transport_unregister() in the scsi_target_reap() routines. I've
no idea why this is suddenly showing up, since the code has been in
there since that function was first invented. However, I've confirmed
this fixes Andrew Vasquez's boot oops.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kurt Huwig [Sat, 24 Dec 2005 23:13:08 +0000 (00:13 +0100)]
[PATCH] n_r3964: fixed usage of HZ; removed bad include
Fix n_r3964 timeouts (hardcoded for 100Hz)
Also the include of <asm/termios.h> in 'n_r3964.h' is unnecessary and
prevents using the header file in any application that has to include
<termios.h> due to duplicate definition of 'struct termio'.
[PATCH] x86_64/ia64 : Fix compilation error for node_to_first_cpu
Fixes a compiler error in node_to_first_cpu, __ffs expects unsigned long as
a parameter; instead cpumask_t was being passed. The macro
node_to_first_cpu was not yet used in x86_64 and ia64 arches, and so we never
hit this. This patch replaces __ffs with first_cpu macro, similar to other
arches.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com> Signed-off-by: Ravikiran G Thirumalai <kiran@scalex86.org> Signed-off-by: Shai Fultheim <shai@scalex86.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Sat, 24 Dec 2005 03:54:46 +0000 (19:54 -0800)]
[PATCH] Fix memory ordering problem in wake_futex()
Fix a memory ordering problem that occurs on IA64. The "store" to q->lock_ptr
in wake_futex() can become visible before wake_up_all() clears the lock in the
futex_q.
Manfred Spraul [Sat, 24 Dec 2005 13:19:24 +0000 (14:19 +0100)]
[PATCH] forcedeth: fix random memory scribbling bug
Two critical bugs were found in forcedeth 0.47:
- TSO doesn't work.
- pci_map_single() for the rx buffers is called with size==0. This bug
is critical, it causes random memory corruptions on systems with an
iommu.
Below is a minimal fix for both bugs, for 2.6.15.
TSO will be fixed properly in the next version. Tested on x86-64.
Frank Pavlic [Tue, 13 Dec 2005 07:22:30 +0000 (08:22 +0100)]
[PATCH] s390: minor qeth network driver fixes
[patch 2/3] s390: minor qeth network driver fixes
From: Frank Pavlic <pavlic@de.ibm.com>
- use netif_carrier_on/off calls to tell network stack
link carrier state
- fix possible kfree on NULL
- PDU_LEN2 is at offset 0x29 otherwise OSN chpid won't initialize
projects / linux-2.6-omap-h63xx.git / log