Oliver Neukum [Sun, 16 Dec 2007 22:07:36 +0000 (14:07 -0800)]
[IRDA]: Race between open and disconnect in irda-usb.
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Sun, 16 Dec 2007 22:05:45 +0000 (14:05 -0800)]
[SCTP]: Flush fragment queue when exiting partial delivery.
At the end of partial delivery, we may have complete messages
sitting on the fragment queue. These messages are stuck there
until a new fragment arrives. This can comletely stall a
given association. When clearing partial delivery state, flush
any complete messages from the fragment queue and send them on
their way up.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Sun, 16 Dec 2007 22:02:07 +0000 (14:02 -0800)]
[AX25]: Locking dependencies fix in ax25_disconnect().
Bernard Pidoux reported these lockdep warnings:
[ INFO: possible irq lock inversion dependency detected ]
2.6.23.1 #1
---------------------------------------------------------
fpac/4933 just changed the state of lock:
(slock-AF_AX25){--..}, at: [<d8be3312>] ax25_disconnect+0x46/0xaf
[ax25]
but this lock was taken by another, soft-irq-safe lock in the past:
(ax25_list_lock){-+..}
and interrupts could create inverse lock ordering between them.
[...]
This means slock-AF_AX25 could be taken both from softirq and process
context with softirqs enabled, so it's endangered itself, but also makes
ax25_list_lock vulnerable. It was not 100% verified if the real lockup
can happen, but this fix isn't very costly and looks safe anyway.
(It was tested by Bernard with 2.6.23.9 and 2.6.24-rc5 kernels.)
Reported_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Tested_by: Bernard Pidoux <pidoux@ccr.jussieu.fr> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Sun, 16 Dec 2007 21:39:57 +0000 (13:39 -0800)]
[IPV6]: Fix the return value of ipv6_getsockopt
If CONFIG_NETFILTER if not selected when compile the kernel source code,
ipv6_getsockopt will returen an EINVAL error if optname is not supported by
the kernel. But if CONFIG_NETFILTER is selected, ENOPROTOOPT error will
be return.
This patch fix to always return ENOPROTOOPT error if optname argument of
ipv6_getsockopt is not supported by the kernel.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Assigning a valid random address to bridge device solves problems
when bridge device is brought up before adding real device to bridge.
When the first real device is added to the bridge, it's address
will overide the bridges random address.
Note: any device added to a bridge must already have a valid
ethernet address.
br_add_if -> br_fdb_insert -> fdb_insert -> is_valid_ether_addr
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Amos Waterland [Fri, 14 Dec 2007 19:30:22 +0000 (11:30 -0800)]
[IPV4]: Updates to nfsroot documentation
The difference between ip=off and ip=::::::off has been a cause of much
confusion. Document how each behaves, and do not contradict ourselves by
saying that "off" is the default when in fact "any" is the default and is
descibed as being so lower in the file.
Signed-off-by: Amos Waterland <apw@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[ATM]: Fix compiler warning noise with FORE200E driver
gcc throws these warnings with:
CONFIG_ATM_FORE200E=m
# CONFIG_ATM_FORE200E_PCA is not set
drivers/atm/fore200e.c:2695: warning: 'fore200e_pca_detect' defined but
not used
drivers/atm/fore200e.c:2748: warning: 'fore200e_pca_remove_one' defined
but not used
By moving the #ifdef CONFIG_ATM_FORE200E_PCA around those two functions,
the compiler warnings are silenced.
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 13 Dec 2007 17:32:04 +0000 (09:32 -0800)]
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
As reported by Damien Thebault, the double POSTROUTING hook invocation
fix caused outgoing packets routed between two bridges to appear without
a link-layer header. The reason for this is that we're skipping the
br_nf_post_routing hook for routed packets now and don't save the
original link layer header, but nevertheless tries to restore it on
output, causing corruption.
The root cause for this is that skb->nf_bridge has no clearly defined
lifetime and is used to indicate all kind of things, but that is
quite complicated to fix. For now simply don't touch these packets
and handle them like packets from any other device.
Tested-by: Damien Thebault <damien.thebault@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Wed, 12 Dec 2007 19:24:19 +0000 (11:24 -0800)]
[TIPC]: Fix semaphore handling.
As noted by Kevin, tipc's release() does down_interruptible() and
ignores the return value. So if signal_pending() we'll end up doing
up() on a non-downed semaphore. Fix.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Wed, 12 Dec 2007 19:10:16 +0000 (11:10 -0800)]
[XFRM]: Display the audited SPI value in host byte order.
Currently the IPsec protocol SPI values are written to the audit log in
network byte order which is different from almost all other values which
are recorded in host byte order. This patch corrects this inconsistency
by writing the SPI values to the audit record in host byte order.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 12 Dec 2007 18:35:16 +0000 (10:35 -0800)]
[NETFILTER]: ip_tables: fix compat copy race
When copying entries to user, the kernel makes two passes through the
data, first copying all the entries, then fixing up names and counters.
On the second pass it copies the kernel and match data from userspace
to the kernel again to find the corresponding structures, expecting
that kernel pointers contained in the data are still valid.
This is obviously broken, fix by avoiding the second pass completely
and fixing names and counters while dumping the ruleset, using the
kernel-internal data structures.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: ctnetlink: set expected bit for related conntracks
This patch is a fix. It sets IPS_EXPECTED for related conntracks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Tue, 11 Dec 2007 11:37:04 +0000 (03:37 -0800)]
[SERIAL] sparc: Infrastructure to fix section mismatch bugs.
This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers. Initially I fixed this build
warning:
WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')
which is done by declaring sunserial_console_match() as __init. This
resulted in build warnings on sunserial_current_minor. To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.
These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.
Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.
Sadly, the following build warning still exists:
WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')
This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David Brownell [Wed, 12 Dec 2007 12:45:25 +0000 (13:45 +0100)]
i2c/isp1301_omap: Build fix
Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jiri Kosina [Wed, 5 Dec 2007 18:14:19 +0000 (15:14 -0300)]
V4L/DVB (6733): DVB: Compile 3000MC-specific DIB code only for CONFIG_DVB_DIB3000MC
On Tue, 4 Dec 2007, Ingo Molnar wrote:
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_get_tuner_i2c_master'
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_set_config'
Seems like -common part contains also code that is not completely
common to all the modules.
V4L/DVB (6750): Fix in-kernel compilation for cxusb
cxusb needs tuner-xc2028*.h files, but Makefile is not adding its patch
drivers/media/dvb/dvb-usb/cxusb.c:33:26: error: tuner-xc2028.h: File not found
drivers/media/dvb/dvb-usb/cxusb.c:34:32: error: tuner-xc2028-types.h: File not found
Benoit Istin [Fri, 7 Dec 2007 05:00:04 +0000 (02:00 -0300)]
V4L/DVB (6746): saa7134-dvb: fix tuning for WinTV HVR-1110
There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Brandon Philips [Sun, 9 Dec 2007 02:05:53 +0000 (23:05 -0300)]
V4L/DVB (6751): V4L: Memory leak! Fix count in videobuf-vmalloc mmap
This is pretty serious bug. map->count is never initialized after the
call to kmalloc making the count start at some random trash value. The
end result is leaking videobufs.
Also, fix up the debug statements to print unsigned values.
Heikki Lindholm [Fri, 30 Nov 2007 16:27:26 +0000 (13:27 -0300)]
V4L/DVB (6690): saa7134: fix ignored interrupts
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Heikki Lindholm [Fri, 23 Nov 2007 21:59:18 +0000 (18:59 -0300)]
V4L/DVB (6666): saa7134-alsa: fix period handling
The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default adc_clock for the zl10353 is different from what was originally
thought to be the case and the TRL nominal rate formula was incorrect as a
result. Use a better (and hopefully now correct) formula.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Brandon Philips [Tue, 13 Nov 2007 23:05:38 +0000 (20:05 -0300)]
V4L/DVB (6601): V4L: videobuf-core locking fixes and comments
- Add comments to functions that require that caller hold q->lock
- Add __videobuf_mmap_free that doesn't hold q->lock for use within videobuf
- Add locking to videobuf_mmap_free
- Fix linux/drivers/media/common/saa7146_video.c which was holding lock around
videobuf_read_stop
- Add locking to functions that operate on a queue
- Add videobuf_stop to take care of stopping in both the read and stream case
TODO: bttv still has an unsafe call to videobuf_queue_is_busy
Herbert Xu [Tue, 11 Dec 2007 12:38:08 +0000 (04:38 -0800)]
[IPSEC]: Fix potential dst leak in xfrm_lookup
If we get an error during the actual policy lookup we don't free the
original dst while the caller expects us to always free the original
dst in case of error.
This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 11 Dec 2007 10:41:25 +0000 (02:41 -0800)]
[VLAN]: Fix potential race in vlan_cleanup_module vs vlan_ioctl_handler.
The vlan module cleanup function starts with
vlan_netlink_fini();
vlan_ioctl_set(NULL);
The first call removes all the vlan devices and
the second one closes the vlan ioctl.
AFAIS there's a tiny race window between these two
calls - after rtnl unregistered all the vlans, but
the ioctl handler isn't set to NULL yet, user can
manage to call this ioctl and create one vlan device,
and that this function will later BUG_ON seeing
non-emply hashes.
I think, that we must first close the vlan ioctl
and only after this remove all the vlans with the
vlan_netlink_fini() call.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 11 Dec 2007 01:18:37 +0000 (17:18 -0800)]
[BNX2]: Fix RX packet rot.
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 11 Dec 2007 01:17:37 +0000 (17:17 -0800)]
[S390]: Fix use of skb after netif_rx
Recently, Wang Chen submitted a patch
(d30f53aeb31d453a5230f526bea592af07944564) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. netif_rx_ni calls netif_rx, so the same problem occurs in
the files below.
I have left the updating of dev->last_rx after the calls to netif_rx_ni
because it seems time dependent, but moved the other field updates before.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
Julia Lawall [Tue, 11 Dec 2007 01:16:56 +0000 (17:16 -0800)]
[XTENSA]: Fix use of skb after netif_rx
Recently, Wang Chen submitted a patch
(d30f53aeb31d453a5230f526bea592af07944564) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
Julia Lawall [Tue, 11 Dec 2007 01:14:46 +0000 (17:14 -0800)]
[UM]: Fix use of skb after netif_rx
Recently, Wang Chen submitted a patch
(d30f53aeb31d453a5230f526bea592af07944564) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
Thomas Graf [Tue, 11 Dec 2007 00:53:29 +0000 (16:53 -0800)]
[IPv6] ESP: Discard dummy packets introduced in rfc4303
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Tue, 11 Dec 2007 00:53:05 +0000 (16:53 -0800)]
[IPv4] ESP: Discard dummy packets introduced in rfc4303
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sat, 8 Dec 2007 07:55:43 +0000 (23:55 -0800)]
[IPV4]: Swap the ifa allocation with the"ipv4_devconf_setall" call
According to Herbert, the ipv4_devconf_setall should be called
only when the ifa is added to the device. However, failed
ifa allocation may bring things into inconsistent state.
Move the call to ipv4_devconf_setall after the ifa allocation.
Fits both net-2.6 (with offsets) and net-2.6.25 (cleanly).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6] XFRM: Fix auditing rt6i_flags; use RTF_xxx flags instead of RTCF_xxx.
RTCF_xxx flags, defined in include/linux/in_route.h) are available for
IPv4 route (rtable) entries only. Use RTF_xxx flags instead, defined
in include/linux/ipv6_route.h, for IPv6 route entries (rt6_info).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ultimately to implement /proc perfectly we need an implementation of
d_revalidate because files and directories can be removed behind the back
of the VFS, and d_revalidate is the only way we can let the VFS know that
this has happened.
Unfortunately the linux VFS can not cope with anything in the path to a
mount point going away. So a proper d_revalidate method that calls d_drop
also needs to call have_submounts which is moderately expensive, so you
really don't want a d_revalidate method that unconditionally calls it, but
instead only calls it when the backing object has really gone away.
proc generic entries only disappear on module_unload (when not counting the
fledgling network namespace) so it is quite rare that we actually encounter
that case and has not actually caused us real world trouble yet.
So until we get a proper test for keeping dentries in the dcache fix the
current d_revalidate method by completely removing it. This returns us to
the current status quo.
So with CONFIG_NETNS=n things should look as they have always looked.
For CONFIG_NETNS=y things work most of the time but there are a few rare
corner cases that don't behave properly. As the network namespace is
barely present in 2.6.24 this should not be a problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Pavel Emelyanov <xemul@openvz.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: "Denis V. Lunev" <den@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rini van Zetten [Mon, 10 Dec 2007 23:49:34 +0000 (15:49 -0800)]
atmel_spi: reload RCR before TCR
We have a wifi module connected to the spi bus and got sometimes FIFO
overrun errors on the spi bus.
After some investigation i found that the driver loads the TCR (transmit
count) register before the RCR (receive count). When the transfer list is
not empty the atmel_spi_next_message is called while tx and rx are enabled.
As soon as the TCR is loaded, hardware starts transfer and causes a rx
fifo overrun because the RCR is not loaded yet.
Load the RCR before the TCR. After this patch the fifo overrun disapears
at out setup.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Rini van Zetten <rini@arvoo.nl> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The esp_reset_cleanup() function is called with the host lock held and
invokes starget_for_each_device() which wants to take it too. Here is a
fix along the lines of shost_for_each_device()/__shost_for_each_device()
adding a __starget_for_each_device() counterpart which assumes the lock
has already been taken.
Eventually, I think the driver should get modified so that more work is
done as a softirq rather than in the interrupt context, but for now it
fixes a bug that causes the spinlock debugger to fire.
While at it, it fixes a small number of cosmetic problems with
starget_for_each_device() too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: James Bottomley <James.Bottomley@steeleye.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Mon, 10 Dec 2007 23:49:30 +0000 (15:49 -0800)]
Fix NULL dereference in umem.c
Fix NULL dereference in umem.c
Signed-off-by: Neil Brown <neilb@suse.de> Tested-by: Dave Chinner <dgc@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
T *d;
...
for_each_compatible_node(d,...)
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Litke [Mon, 10 Dec 2007 23:49:28 +0000 (15:49 -0800)]
hugetlb: handle write-protection faults in follow_hugetlb_page
The follow_hugetlb_page() fix I posted (merged as git commit 5b23dbe8173c212d6a326e35347b038705603d39) missed one case. If the pte is
present, but not writable and write access is requested by the caller to
get_user_pages(), the code will do the wrong thing. Rather than calling
hugetlb_fault to make the pte writable, it notes the presence of the pte
and continues.
This simple one-liner makes sure we also fault on the pte for this case.
Please apply.
Signed-off-by: Adam Litke <agl@us.ibm.com> Acked-by: Dave Kleikamp <shaggy@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Newton [Mon, 10 Dec 2007 23:49:27 +0000 (15:49 -0800)]
spi_imx: fix typo in description
Signed-off-by: Will Newton <will.newton@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Newton [Mon, 10 Dec 2007 23:49:26 +0000 (15:49 -0800)]
spi_bfin5xx: fix typo in description
Signed-off-by: Will Newton <will.newton@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Newton [Mon, 10 Dec 2007 23:49:25 +0000 (15:49 -0800)]
pxa2xx_spi: fix typo in description
Signed-off-by: Will Newton <will.newton@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Mon, 10 Dec 2007 23:49:22 +0000 (15:49 -0800)]
pcmcia: fix kernel-doc comments
Fix kernel-doc comments in drivers/pcmcia/:
- ti113x.h does not contain kernel-doc, so don't use /** to begin a doc
comment
- yenta_socket.c: remove /** on non-kernel-doc comments;
escape the ':' in an "http:" comment so that it won't be treated as a
section heading;
- cs.c: remove /** on non-kernel-doc comments & add function parameter info
- ds.c: fix function parameter info
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Delete refereces to HOSTS_C
- Switch to module_init/module_exit instead of detect/release
- Don't pass around the host template and rename it to adpt_template
- Switch from scsi_register/scsi_unregister to scsi_host_alloc,
scsi_add_host, scsi_scan_host and scsi_host_put.
Because it caused (for unknown reasons) Andres' all-data-reads-as-zeroes
problem, reported at
http://groups.google.com/group/fa.linux.kernel/msg/083a9acff0330234
Cc: Matthew Wilcox <matthew@wil.cx> Cc: "Salyzyn, Mark" <mark_salyzyn@adaptec.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Anders Henke <anders.henke@1und1.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jarod Wilson [Mon, 3 Dec 2007 18:43:12 +0000 (13:43 -0500)]
firewire: OHCI 1.0 Isochronous Receive support
Third rendition of FireWire OHCI 1.0 Isochronous Receive support, using a
zer-copy method similar to OHCI 1.1 which puts the IR data payload directly
into the userspace buffer. The zero-copy implementation eliminates the
video artifacts, audio popping, and buffer underrun problems seen with
version 1 of this patch, as well as fixing a regression in OHCI 1.1 support
introduced by version 2 of this patch.
Successfully tested in OHCI 1.1 mode on the following chipsets:
- NEC uPD72847 (rev 01), OHCI 1.1 (PCI)
- Ti XIO2200(A) (rev 01), OHCI 1.1 (PCIe)
- Ti TSB41AB2 (rev 01), OHCI 1.1 (PCI on SB Audigy)
- Apple UniNorth 2 (rev 81), OHCI 1.1 (PowerBook G4 onboard)
Successfully tested in OHCI 1.0 mode on the following chipsets:
- Agere FW323 (rev 06), OHCI 1.0 (Mac Mini onboard)
- Agere FW323 (rev 06), OHCI 1.0 (PCI)
- Via VT6306 (rev 46), OHCI 1.0 (PCI)
- NEC OrangeLink (rev 01), OHCI 1.0 (PCI)
- NEC uPD72847 (rev 01), OHCI 1.1 (PCI)
- Ti XIO2200(A) (rev 01), OHCI 1.1 (PCIe)
The bulk of testing was done in an x86_64 system, but was also successfully
sanity-tested on other systems, including a PPC(32) PowerBook G4 and an i686
EPIA M10k. Crude benchmarking (watching top during capture) puts the cpu
utilization during capture on the EPIA's 1GHz Via C3 processor around 13%,
which is down from 30% with the v1 code.
Some implementation details:
To maintain the same userspace API as dual-buffer mode, we set up two
descriptors for every incoming packet. The first is an INPUT_MORE descriptor,
pointing to a buffer large enough to hold just the packet's iso headers,
immediately followed by an INPUT_LAST descriptor, pointing to a chunk of the
userspace buffer big enough for the packet's data payload. With this setup,
each incoming packet fills in these two descriptors in a manner that very
closely emulates dual-buffer receive, to the point where the bulk of the
handle_ir_* code is now identical between the two (and probably primed for
some restructuring to share code between them).
The only caveat I have at the moment is that neither of my OHCI 1.0 Via
VT6307-based FireWire controllers work particularly well with this code
for reasons I have yet to figure out.
Signed-off-by: Jarod Wilson <jwilson@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Mon, 10 Dec 2007 18:18:27 +0000 (10:18 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Fix xfs_ichgtime()s broken usage of I_SYNC
[XFS] Make xfsbufd threads freezable
[XFS] revert to double-buffering readdir
[XFS] Fix broken inode cluster setup.
[XFS] Clear XBF_READ_AHEAD flag on I/O completion.
[XFS] Fixed a few bugs in xfs_buf_associate_memory()
[XFS] 971064 Various fixups for xfs_bulkstat().
[XFS] Fix dbflush panic in xfs_qm_sync.
"It seems the whole MIPS resource managment is complicated enough (out
of necessity) that only a few people actually grok it. Ioports being
actually memory mapped on MIPS only makes the confusion worse, sigh."
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Alan Cox <alan@redhat.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PowerMac and CHRP/BriQ platforms have quirks to switch some IDE
controllers from legacy mode to fully native mode. Those quirks
however will not work properly anymore due to a change to the
generic code to better handle legacy IDE resources.
This fixes it by moving those quirk to "early" quirks (so they
run before resources are probed for the devices) and clearing
all BARs after the conversion to force a reallocation of sane
values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Chinner [Fri, 7 Dec 2007 03:09:11 +0000 (14:09 +1100)]
[XFS] Fix xfs_ichgtime()s broken usage of I_SYNC
The recent I_LOCK->I_SYNC changes mistakenly changed xfs_ichgtime to look
at I_SYNC instead of I_LOCK. This was incorrect and prevents newly created
inodes from moving to the dirty list. Change this to the correct check
which is for I_NEW, not I_LOCK or I_SYNC so that behaviour is correct.
Fix breakage caused by commit 831441862956fffa17b9801db37e6ea1650b0f69
that did not introduce the necessary call to set_freezable() in
xfs/linux-2.6/xfs_buf.c .
The current readdir implementation deadlocks on a btree buffers locks
because nfsd calls back into ->lookup from the filldir callback. The only
short-term fix for this is to revert to the old inefficient
double-buffering scheme.
David Chinner [Fri, 23 Nov 2007 05:30:23 +0000 (16:30 +1100)]
[XFS] Fix broken inode cluster setup.
The radix tree based inode caches did away with the inode cluster hashes,
replacing them with a bunch of masking and gang lookups on the radix tree.
This masking got broken when moving the code to per-ag radix trees and
indexing by agino # rather than straight inode number. The result is
clustered inode writeback does not cluster and things can go extremely
slowly when there are lots of inodes to write.
Fix it up by comparing the agino # of the inode we just looked up to the
index of the cluster we are looking for.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
SGI-PV: 972915
SGI-Modid: xfs-linux-melb:xfs-kern:30033a
Signed-off-by: David Chinner <dgc@sgi.com> Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Lachlan McIlroy [Tue, 27 Nov 2007 06:01:24 +0000 (17:01 +1100)]
[XFS] Fixed a few bugs in xfs_buf_associate_memory()
- calculation of 'page_count' was incorrect as it did not
consider the offset of 'mem' into the first page. The
logic to bump 'page_count' didn't work if 'len' was <=
PAGE_CACHE_SIZE (ie offset = 3k, len = 2k).
- setting b_buffer_length to 'len' is incorrect if 'offset'
is > 0. Set it to the total length of the buffer.
- I suspect that passing a non-aligned address into
mem_to_page() for the first page may have been causing
issues - don't know but just tidy up that code anyway.
Lachlan McIlroy [Fri, 23 Nov 2007 05:30:32 +0000 (16:30 +1100)]
[XFS] 971064 Various fixups for xfs_bulkstat().
- sanity check for NULL user buffer in xfs_ioc_bulkstat[_compat]()
- remove the special case for XFS_IOC_FSBULKSTAT with count == 1. This
special case causes bulkstat to fail because the special case uses
xfs_bulkstat_single() instead of xfs_bulkstat() and the two functions
have different semantics. xfs_bulkstat() will return the next inode
after the one supplied while skipping internal inodes (ie quota inodes).
xfs_bulkstate_single() will only lookup the inode supplied and return
an error if it is an internal inode.
- in xfs_bulkstat(), need to initialise 'lastino' to the inode supplied
so in cases were we return without examining any inodes the scan wont
restart back at zero.
- sanity check for valid *ubcountp values. Cannot sanity check for valid
ubuffer here because some users of xfs_bulkstat() don't supply a buffer.
- checks against 'ubleft' (the space left in the user's buffer) should be
against 'statstruct_size' which is the supplied minimum object size.
The mixture of checks against statstruct_size and 0 was one of the
reasons we were skipping inodes.
- if the formatter function returns BULKSTAT_RV_NOTHING and an error and
the error is not ENOENT or EINVAL then we need to abort the scan. ENOENT
is for inodes that are no longer valid and we just skip them. EINVAL is
returned if we try to lookup an internal inode so we skip them too. For
a DMF scan if the inode and DMF attribute cannot fit into the space left
in the user's buffer it would return ERANGE. We didn't handle this error
and skipped the inode. We would continue to skip inodes until one fitted
into the user's buffer or we completed the scan.
- put back the recalculation of agino (that got removed with the last fix)
at the end of the while loop. This is because the code at the start of
the loop expects agino to be the last inode examined if it is non-zero.
- if we found some inodes but then encountered an error, return success
this time and the error next time. If the formatter aborted with ENOMEM
we will now return this error but only if we couldn't read any inodes.
Previously if we encountered ENOMEM without reading any inodes we
returned a zero count and no error which falsely indicated the scan was
complete.
Donald Douwsma [Fri, 23 Nov 2007 05:27:42 +0000 (16:27 +1100)]
[XFS] Fix dbflush panic in xfs_qm_sync.
The recent behaviour layer removal dropped the check for quotas that have
been requested at mount time but have subsequently been turned off. This
results in a panic when accessing m_quotainfo which has been freed.
This patch adds the check originally made by xfs_qm_syncall() to
xfs_qm_sync().
Linus Torvalds [Sun, 9 Dec 2007 18:14:36 +0000 (10:14 -0800)]
Avoid double memclear() in SLOB/SLUB
Both slob and slub react to __GFP_ZERO by clearing the allocation, which
means that passing the GFP_ZERO bit down to the page allocator is just
wasteful and pointless.
Acked-by: Matt Mackall <mpm@selenic.com> Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
caused certain external modules not to build and
also caused 'make targz-pkg' to fail.
This is a minimal fix so we revert to previous
behaviour - but we do not overwrite the Makefile
in the top-level directory.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Tested-by: Jay Cliburn <jacliburn@bellsouth.net> Cc: Jay Cliburn <jacliburn@bellsouth.net>
Sam Ravnborg [Thu, 6 Dec 2007 21:20:11 +0000 (22:20 +0100)]
kbuild: fix building with redirected output.
Jan Altenberg <jan.altenberg@linutronix.de> reported that
building with redirected input like this failed:
make O=dir oldconfig bzImage < /dev/null
The problem were caused by a make silentoldconfig being
run before oldconfig and with a non-recent .config the build
failed because silentoldconfig requires non-redirected stdin.
Silentoldconfig was run as a side-effect of having the
top-level Makefile re-made by make.
Introducing an empty rule for the top-level Makefile
(and Kbuild.include) fixed the issue.
Ralf Baechle [Fri, 16 Nov 2007 14:54:46 +0000 (14:54 +0000)]
[MIPS] Malta: Enable tickless and highres timers.
Most Malta use an FPGA CPU card which rarely is good for more than 40MHz.
So the performance penalta of the regular timer interrupt, especially
for the VSMP kernel model is significant, even at a mere 100Hz.
Kenji Kaneshige [Fri, 9 Nov 2007 01:51:01 +0000 (10:51 +0900)]
[IA64] Fix iosapic interrupt delivery mode for CPE
If "CPEI Processor Override" bit is not set in "Platform Interrupt
Source Flags" in "Platform Interrupt Sources Structure" in ACPI MADT,
the target processor of CPEI is restricted to a specific CPU. Because
of this, the delivery mode for CPEI should be IOSAPIC_FIXED.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Shaohua Li [Tue, 13 Nov 2007 06:55:20 +0000 (14:55 +0800)]
[IA64] kprobe: make kreturn probe handler stack unwind correct
Restore regs->ccr_iip before kreturn probe handler runs. In this way, if
probe handler does unwind, unwind can correctly get the stack trace.
Fixes: http://sourceware.org/bugzilla/show_bug.cgi?id=5051 Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
projects / linux-2.6-omap-h63xx.git / log