The allocated RX buffer size was 64 bytes bigger than the PCI mapped
size with no good reason. If the packet was actually using the buffer up
to its limit and if the last 64 bytes of the buffer crossed 4KB boundary
then an unmapped PCI page was accessed. The fix is to use only one
parameter for the buffer size - there is no need to differentiate
between the buffer size and the PCI mapping size since the extra 64
bytes can actually be used by the FW to align the Ethernet payload to
64 bytes.
Also updating the driver version and date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.
Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.
This patch fixes memory freeing problem in the previous patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ian Schram <ischram@telenet.be> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 3 Sep 2008 03:18:47 +0000 (11:18 +0800)]
iwlwifi: fix rx_chain computation
This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error. Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Wed, 3 Sep 2008 03:18:46 +0000 (11:18 +0800)]
iwlwifi: fix station mimo power save values
This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Wed, 3 Sep 2008 03:18:44 +0000 (11:18 +0800)]
iwlwifi: remove false rxon if rx chain changes
Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Wed, 3 Sep 2008 03:18:43 +0000 (11:18 +0800)]
iwlwifi: fix hidden ssid discovery in passive channels
This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: Cahill Ben <ben.m.cahill@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Wed, 3 Sep 2008 06:38:32 +0000 (23:38 -0700)]
tipc: Don't use structure names which easily globally conflict.
Andrew Morton reported a build failure on sparc32, because TIPC
uses names like "struct node" and there is a like named data
structure defined in linux/node.h
This just regexp replaces "struct node*" to "struct tipc_node*"
to avoid this and any future similar problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Sep 2008 03:14:15 +0000 (20:14 -0700)]
ipsec: Fix deadlock in xfrm_state management.
Ever since commit 4c563f7669c10a12354b72b518c2287ffc6ebfb3
("[XFRM]: Speed up xfrm_policy and xfrm_state walking") it is
illegal to call __xfrm_state_destroy (and thus xfrm_state_put())
with xfrm_state_lock held. If we do, we'll deadlock since we
have the lock already and __xfrm_state_destroy() tries to take
it again.
Fix this by pushing the xfrm_state_put() calls after the lock
is dropped.
Signed-off-by: David S. Miller <davem@davemloft.net>
net/xfrm: Use an IS_ERR test rather than a NULL test
In case of error, the function xfrm_bundle_create returns an ERR
pointer, but never returns a NULL pointer. So a NULL test that comes
after an IS_ERR test should be deleted.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match_bad_null_test@
expression x, E;
statement S1,S2;
@@
x = xfrm_bundle_create(...)
... when != x = E
* if (x != NULL)
S1 else S2
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message.
This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.
As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.
ath9k: Incorrect key used when group and pairwise ciphers are different.
Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.
Also use mac80211 provided enums for key length calculation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> CC: Ingo Molnar <mingo@elte.hu> CC: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Thu, 28 Aug 2008 12:12:06 +0000 (15:12 +0300)]
mac80211: Fix debugfs union misuse and pointer corruption
debugfs union in struct ieee80211_sub_if_data is misused by including a
common default_key dentry as a union member. This ends occupying the same
memory area with the first dentry in other union members (structures;
usually drop_unencrypted). Consequently, debugfs operations on
default_key symlinks and drop_unencrypted entry are using the same
dentry pointer even though they are supposed to be separate ones. This
can lead to removing entries incorrectly or potentially leaving
something behind since one of the dentry pointers gets lost.
Fix this by moving the default_key dentry to a new struct
(common_debugfs) that contains dentries (more to be added in future)
that are shared by all vif types. The debugfs union must only be used
for vif type-specific entries to avoid this type of pointer corruption.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Wed, 27 Aug 2008 22:05:08 +0000 (01:05 +0300)]
wireless/libertas/if_cs.c: fix memory leaks
The leak in if_cs_prog_helper() is obvious.
It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Sat, 23 Aug 2008 18:03:34 +0000 (19:03 +0100)]
orinoco: Multicast to the specified addresses
When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.
If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.
Only write the multicast addresses we have specifically set.
Signed-off-by: David Kilroy <kilroyd@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Thu, 28 Aug 2008 09:25:05 +0000 (17:25 +0800)]
iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE)
The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 28 Aug 2008 09:25:04 +0000 (17:25 +0800)]
iwlwifi: workaround interrupt handling no some platforms
This patch adds workaround for an interrupt related hardware bug on
some platforms. (Apparently these platforms boot-up w/ INTX_DISABLED
set. -- JWL)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS
Current setup with hal and NetworkManager will fail to work
without newest hal version with this config option disabled.
Although this will solve itself by time, at the moment it is
dishonest to say that we don't know any software that uses it,
if there are many many people relying on old hal versions.
Signed-off-by: Florian Mickler <florian@mickler.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Fri, 29 Aug 2008 21:37:23 +0000 (14:37 -0700)]
net: Unbreak userspace usage of linux/mroute.h
Nothing in linux/pim.h should be exported to userspace.
This should fix the XORP build failure reported by
Jose Calhariz, the debain package maintainer.
Nothing originally in linux/mroute.h was exported to userspace
ever, but some of this stuff started to be when it was moved into
this new linux/pim.h, and that was wrong. If we didn't provide these
definitions for 10 years we can reasonably expect that applications
defined this stuff locally or used GLIBC headers providing the
protocol definitions. And as such the only result of this can
be conflict and userland build breakage.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Fri, 29 Aug 2008 21:21:52 +0000 (14:21 -0700)]
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Wed, 27 Aug 2008 23:09:49 +0000 (16:09 -0700)]
sctp: fix random memory dereference with SCTP_HMAC_IDENT option.
The number of identifiers needs to be checked against the option
length. Also, the identifier index provided needs to be verified
to make sure that it doesn't exceed the bounds of the array.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ayaz Abdulla [Wed, 20 Aug 2008 23:34:37 +0000 (16:34 -0700)]
forcedeth: fix checksum flag
Fix the checksum feature advertised in device flags. The hardware support
TCP/UDP over IPv4 and TCP/UDP over IPv6 (without IPv6 extension headers).
However, the kernel feature flags do not distinguish IPv6 with/without
extension headers.
Therefore, the driver needs to use NETIF_F_IP_CSUM instead of
NETIF_F_HW_CSUM since the latter includes all IPv6 packets.
A future patch can be created to check for extension headers and perform
software checksum calculation.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Manfred Spraul <manfred@colorfullife.com Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Oliver Martin [Sat, 23 Aug 2008 20:08:47 +0000 (22:08 +0200)]
net/usb/mcs7830: add set_mac_address
Implement set_mac_address for mcs7830. This enables me to use it with my
cable modem.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Arnd Bergmann [Sat, 23 Aug 2008 20:02:23 +0000 (22:02 +0200)]
net/usb/mcs7830: new device IDs
This adds USB device IDs for MosChip 7730 and Sitecom LN030
to the mcs7830 driver. The IDs have been reported to work without
further modifications.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: David Brownell <david-b@pacbell.net> Cc: Viktor Horvath <ViktorHorvath@gmx.net> Cc: Robbert Wethmar <robbert@wethmar.nl> Cc: Bart van der Klip <bklip@xs4all.nl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Santiago Leon [Wed, 20 Aug 2008 19:09:19 +0000 (13:09 -0600)]
ibmveth: fix bad UDP checksums
This patch fixes a ibmveth bug where bad UDP checksums are being transmitted
when checksum offloading is enabled.
The hypervisor does checksum offloading only on TCP packets, so ibmveth calls
skb_checksum_help() for any other protocol. The bug happens because
the packet is being modified after the DMA map, so we would need a memory
barrier before making the hypervisor call. Reordering the code so that the
DMA map happens after skb_checksum_help() has the additional advantage of
fixing a DMA map leak if skb_checksum_help() where to fail.
Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Fri, 8 Aug 2008 23:51:26 +0000 (16:51 -0700)]
igb: remove 82576 quad adapter
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Takashi Iwai [Wed, 20 Aug 2008 23:34:35 +0000 (16:34 -0700)]
drivers/net/skfp/ess.c: fix compile warnings
CC [M] drivers/net/skfp/ess.o
drivers/net/skfp/ess.c: In function 'ess_send_response':
drivers/net/skfp/ess.c:513: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c: In function 'ess_send_alc_req':
drivers/net/skfp/ess.c:609: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c:639: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Philip Love [Wed, 27 Aug 2008 09:33:50 +0000 (02:33 -0700)]
tcp: fix tcp header size miscalculation when window scale is unused
The size of the TCP header is miscalculated when the window scale ends
up being 0. Additionally, this can be induced by sending a SYN to a
passive open port with a window scale option with value 0.
Signed-off-by: Philip Love <love_phil@emc.com> Signed-off-by: Adam Langley <agl@imperialviolet.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Wed, 27 Aug 2008 09:27:10 +0000 (02:27 -0700)]
pkt_sched: Fix sch_tree_lock()
Use new qdisc_root_sleeping_lock() instead of qdisc_root_lock() as
sch_tree_lock() because this lock could be used while dev is
deactivated, but we never need to use this with noop_qdisc as a root.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Wed, 27 Aug 2008 09:25:17 +0000 (02:25 -0700)]
pkt_sched: Fix gen_estimator locks
While passing a qdisc root lock to gen_new_estimator() and
gen_replace_estimator() dev could be deactivated or even before
grafting proper root qdisc as qdisc_sleeping (e.g. qdisc_create), so
using qdisc_root_lock() is not enough. This patch adds
qdisc_root_sleeping_lock() for this, plus additional checks, where
necessary.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-D. Wacker [Thu, 21 Aug 2008 15:10:25 +0000 (17:10 +0200)]
LCS recovery dumps when cable reconnect
LCS recovery dumps in irq routine when CCW address in
Subchannel Status Word (SCSW) is zero. This occurs
when recovery is driven after cable reconnect.
probe_error() frees memory only, if cgdev->dev.driver_data refers
to the claw_privbk structure. Move forward its setting in claw_probe()
to ensure proper freeing of claw_privbk allocations.
Cc: Daniel <danielm77@spray.se> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Tue, 26 Aug 2008 11:25:13 +0000 (04:25 -0700)]
igb: fix setting the number of tx queues
The real_num_tx_queues was not being set when in MSI-X only mode. This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Tue, 26 Aug 2008 11:25:05 +0000 (04:25 -0700)]
igb: ethtool -d reads EICR which is incorrect as it is read on clear
Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts. To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Tue, 26 Aug 2008 11:25:03 +0000 (04:25 -0700)]
igb: force all queues to interrupt once every 2 seconds
Set the EICS bit for each of the RX queues at least once every 2 seconds to
prevent the rx queues from stalling.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jarek Poplawski [Wed, 27 Aug 2008 09:12:52 +0000 (02:12 -0700)]
pkt_sched: Fix dev_graft_qdisc() locking
During dev_graft_qdisc() dev is deactivated, so qdisc_root_lock()
returns wrong lock of noop_qdisc instead of qdisc_sleeping.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The rates tag of the assoc request has room for only 8 rates. In case of
802.11g an extended rate tag is appended. However in net/wireless/mlme.c
an extended (empty) rate tag is also appended if the number of rates is
exact 8. This empty (length=0) extended rates tag causes some APs to
deny association with code 18 (unsupported rates). These APs include my
ZyXEL G-570U, and according to Tomas Winkler som Cisco APs.
'If count == 8' has been used to check for the need for an extended rates
tag. But count would also be equal to 8 if the for loop exited because of
no more supported rates. Therefore a check for count being less than
rates_len would seem more correct.
Thanks to:
* Dan Williams for newbie guidance
* Tomas Winkler for confirming the problem
Signed-off-by: Jan-Espen Pettersen <sigsegv@radiotube.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 25 Aug 2008 08:57:06 +0000 (11:57 +0300)]
mac80211: Fix debugfs file add/del for netdev
Previous version was using incorrect union structures for non-AP
interfaces when adding and removing max_ratectrl_rateidx and
force_unicast_rateidx entries. Depending on the vif type, this ended
up in corrupting debugfs entries since the dentries inside different
union structures ended up going being on top of eachother.. As the
end result, debugfs files were being left behind with references to
freed data (instant kernel oops on access) and directories were not
removed properly when unloading mac80211 drivers. This patch fixes
those issues by using only a single union structure based on the vif
type.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Sat, 23 Aug 2008 16:27:38 +0000 (18:27 +0200)]
net/mac80211/mesh.c: correct the argument to __mesh_table_free
In the function mesh_table_grow, it is the new table not the argument table
that should be freed if the function fails (cf commit bd9b448f4c0a514559bdae4ca18ca3e8cd999c6d)
The semantic match that detects this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = mesh_table_alloc@p1(...)
...
if (x == NULL) S
... when != E = x
when != mesh_table_free(x)
goto@p2 l;
... when != E = x
when != f(...,x,...)
when any
(
return \(0\|x\);
|
return@p3 ...;
)
Jouni Malinen [Tue, 19 Aug 2008 07:54:32 +0000 (10:54 +0300)]
mac80211: Use IWEVASSOCREQIE instead of IWEVCUSTOM
The previous code was using IWEVCUSTOM to report IEs from AssocReq and
AssocResp frames into user space. This can easily hit the 256 byte
limit (IW_CUSTOM_MAX) with APs that include number of vendor IEs in
AssocResp. This results in the event message not being sent and dmesg
showing "wlan0 (WE) : Wireless Event too big (366)" type of errors.
Convert mac80211 to use IWEVASSOCREQIE/IWEVASSOCRESPIE to avoid the
issue of being unable to send association IEs as wireless events. These
newer event types use binary encoding and larger maximum size
(IW_GENERIC_IE_MAX = 1024), so the likelyhood of not being able to send
the IEs is much smaller than with IWEVCUSTOM. As an extra benefit, the
code is also quite a bit simpler since there is no need to allocate an
extra buffer for hex encoding.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felipe Balbi [Mon, 18 Aug 2008 19:56:53 +0000 (22:56 +0300)]
net: rfkill: add missing line break
Trivial patch adding a missing line break on
rfkill_claim_show().
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.co> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiri Slaby [Mon, 18 Aug 2008 19:45:28 +0000 (21:45 +0200)]
Ath5k: fix bintval setup
bintval is set to the initial value at .config_interface which is too
late, since it overwrites previously set value from .config. Move the
initialization to the .add_interface.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiri Slaby [Mon, 18 Aug 2008 19:45:27 +0000 (21:45 +0200)]
Ath5k: lock beacons
Beacons setup and config was racy with beacon send. Ensure that
ISR and reset functions see consistent state of bbuf.
Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it
from atomic now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Mon, 18 Aug 2008 19:40:02 +0000 (15:40 -0400)]
atmel: return ENOENT on request_firmware failure
Return errors from request_firmware() (like other drivers that do
firmware load on device open) and make up plausible codes for other
error conditions. Gives userspace tools like NetworkManager a clue that
firmware may be missing when the result of setting IFF_UP is ENOENT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
v2: fix reversed check of atmel_wakeup_firmware() in probe_atmel_card() Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yitchak Gertner [Mon, 25 Aug 2008 22:27:06 +0000 (15:27 -0700)]
bnx2x: Multi Queue
The multi queue support is still disabled by default for the bnx2x
(needs some more testing and validation), but there are 2 obvious bug in
it which are fixed in this patch
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Mon, 25 Aug 2008 22:26:24 +0000 (15:26 -0700)]
bnx2x: NAPI and interrupts enable/disable
Fixing the order of enabling and disabling NAPI and the interrupts
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Mon, 25 Aug 2008 22:25:45 +0000 (15:25 -0700)]
bnx2x: NIC load failure cleanup
Load failures were not handled correctly
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Mon, 25 Aug 2008 22:24:21 +0000 (15:24 -0700)]
bnx2x: Initialization structure
The TPA initialization is part of the FW internal memory initialization
and so it is moved to the appropriate function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 25 Aug 2008 22:19:17 +0000 (15:19 -0700)]
bnx2x: Rx work check
The has Rx work check was wrong: when the FW was at the end of the page,
the driver was already at the beginning of the next page. Since the
check only validated that both driver and FW are pointing to the same
place, it concluded that there is still work to be done. This caused
some serious issues including long latency results on ping-pong test and
lockups while unloading the driver in that condition.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 25 Aug 2008 22:16:19 +0000 (15:16 -0700)]
sctp: add verification checks to SCTP_AUTH_KEY option
The structure used for SCTP_AUTH_KEY option contains a
length that needs to be verfied to prevent buffer overflow
conditions. Spoted by Eugene Teo <eteo@redhat.com>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The mv643xx_eth hardware ignores the lower three bits of the buffer
size field in receive descriptors, causing the reception of full-sized
packets to fail at some MTUs. Fix this by rounding the size of
allocated receive buffers up to a multiple of eight bytes.
While we are at it, add a bit of extra space to each receive buffer so
that we can handle multiple vlan tags on ingress.
mv643xx_eth: fix NULL pointer dereference in rxq_process()
When we are low on memory, the assumption that every descriptor in the
receive ring will have an skbuff associated with it does not hold.
rxq_process() was assuming that if the receive descriptor it is working
on is not owned by the hardware, it can safely be processed and handed
to the networking stack. But a descriptor in the receive ring not being
owned by the hardware can also happen when we are low on memory and did
not manage to refill the receive ring fully.
This patch changes rxq_process()'s bailout condition from "the first
receive descriptor to be processed is owned by the hardware" to "the
first receive descriptor to be processed is owned by the hardware OR
the number of valid receive descriptors in the ring is zero".
Nicolas Pitre noted that mv643xx_eth_poll was incorrectly using
non-IRQ-safe locks while checking whether to wake up the netdevice's
transmit queue. Convert the locking to *_irq() variants, since we
are running from softirq context where interrupts are enabled.
mv643xx_eth: fix double add_timer() on the receive oom timer
Commit 12e4ab79cd828563dc090d2117dc8626b344bc8f ("mv643xx_eth: be
more agressive about RX refill") changed the condition for the receive
out-of-memory timer to be scheduled from "the receive ring is empty"
to "the receive ring is not full".
This can lead to a situation where the receive out-of-memory timer is
pending because a previous rxq_refill() didn't manage to refill the
receive ring entirely as a result of being out of memory, and
rxq_refill() is then called again as a side effect of a packet receive
interrupt, and that rxq_refill() call then again does not succeed to
refill the entire receive ring with fresh empty skbuffs because we are
still out of memory, and then tries to call add_timer() on the already
scheduled out-of-memory timer.
This patch fixes this issue by changing the add_timer() call in
rxq_refill() to a mod_timer() call. If the OOM timer was not already
scheduled, this will behave as before, whereas if it was already
scheduled, this patch will push back its firing time a bit, which is
safe because we've (unsuccessfully) attempted to refill the receive
ring just before we do this.
When a receive interrupt occurs, mv643xx_eth would first process the
receive descriptors and then ACK the receive interrupt, instead of the
other way round.
This would leave a small race window between processing the last
receive descriptor and clearing the receive interrupt status in which
a new packet could come in, which would then 'rot' in the receive
ring until the next receive interrupt would come in.
Fix this by ACKing (clearing) the receive interrupt condition before
processing the receive descriptors.
projects / linux-2.6-omap-h63xx.git / log