1) reading some of the registers in our hardware causes them to clear,
so don't read ICR in the ethtool register dump function.
2) several register iterators were not iterating
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe: Update watchdog thread to accomodate longerlink_up events
This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Wed, 3 Sep 2008 14:37:01 +0000 (15:37 +0100)]
sfc: Fix type of FALCON_SPI_MAX_LEN
FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int. This results in warnings from min() on 64-bit
architectures where they are different. Add a cast to make it match.
From: Steve Hodgson <shodgson@solarflare.com> Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:50:28 +0000 (12:50 +0100)]
sfc: Use CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS where appropriate
For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words. There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:49:37 +0000 (12:49 +0100)]
sfc: Make queue flushes more reliable
Increase the potential retry count for RX flushes from 5 to 100.
Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).
To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
8139too: [cosmetic] fix incorrect register for flash-rom
I would like to submit a correction to the driver
drivers/net/8139too.c,
which in no way changes the compiled driver, but does change
the value of a previously incorrect value for the configuration
register address of Flash PROM on the network processor rtl8139C.
This corrected value is in accordance with the datasheet
for rtl8139C, and in addition this new value is indeed used
in other functional drivers that use this adapter for
programming a Flash memory chip in situ. But as said,
the two new constants are never referenced in the driver
maintained by you: they are only informational and correct!
s2io: Fix enabling VLAN tag stripping at driver initialization
VLAN doesn't work except if you'd opened the interface in promiscuous
mode before. This happens because VLAN tag stripping is not correctly
marked as enabled at device startup
Also, the vlan_strip_flag field was moved to the private network
structure.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Vlad Yasevich [Thu, 28 Aug 2008 19:38:41 +0000 (15:38 -0400)]
bonding: Do not tx-balance some IPv6 packets on ALB/TLB bonds
IPv6 all-node-multicasts and DAD probes should not be tx-balanced
on ALB/TLB bonds. The all-node-multicast is an equivalent to IPv4
broadcasts. DAD probes have to be sent only on the primary so that
we don't get false-positive detections.
Matthew Wilcox [Tue, 12 Aug 2008 13:13:14 +0000 (07:13 -0600)]
[netdrvr] atl1e: Don't take the mdio_lock in atl1e_probe
Lockdep warns about the mdio_lock taken with interrupts enabled then later
taken from interrupt context. Initially, I considered changing these
to spin_lock_irq/spin_unlock_irq, but then I looked at atl1e_phy_init()
and saw that it calls msleep(). Sleeping while holding a spinlock is
not allowed either.
In the probe path, we haven't registered the interrupt handler, so
it can't poke at this card yet. It's before we call register_netdev(),
so I don't think any other threads can reach this card either. If I'm
right, we don't need a spinlock at all.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Fries [Tue, 9 Sep 2008 03:01:14 +0000 (22:01 -0500)]
[netdrvr] ne: Fix suspend and resume for ISA PnP cards.
A call to pnp_stop_dev and pnp_start_dev now shuts down and
initializes plug and play devices for suspend and resume.
Signed-off-by: David Fries <david@fries.net> Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Martin Gebert [Wed, 23 Jul 2008 07:40:09 +0000 (09:40 +0200)]
[netdrvr] au1000_eth: Spinlock initialisation fix
Seems like the spinlock for the AU1x00 ethernet device is initialised too
late, as it is already used in enable_mac(), which is called via
mii_probe() before the init takes place.
The attached patch is working here for a Linux Au1100 2.6.22.6 kernel,
and as far as I checked should also be applicable to the current head
(just line numbers differ).
Signed-off-by: Martin Gebert <Martin.Gebert@alpha-bit.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Chris Snook [Tue, 9 Sep 2008 07:26:57 +0000 (03:26 -0400)]
MAINTAINERS: add Atheros maintainer for atlx
Jie Yang at Atheros is getting more directly involved with upstream work on the
atl* drivers. This patch changes the ATL1 entry to ATLX (atl2 support posted
to netdev today) and adds him as a maintainer.
Andrew Morton [Fri, 5 Sep 2008 21:04:07 +0000 (14:04 -0700)]
drivers/net/mlx4/alloc.c needs mm.h
sparc32 allmodconfig with linux-next:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:164: error: 'PAGE_KERNEL' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:164: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:164: error: for each function it appears in.)
this is due to some header shuffle in linux-next. I didn't look to see what
it was. I'd sugges that this patch be merged ahead of a linux-next merge to
avoid bisection breaks.
We strictly only need asm/pgtable.h, but going direct to asm includes always
seems grubby.
Cc: Jeff Garzik <jeff@garzik.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Self-baked macros cause bunch of compile warnings like below:
CC [M] drivers/net/skfp/pmf.o
CC net/ipv4/fib_semantics.o
drivers/net/skfp/pmf.c:86: warning: cast from pointer to integer of different size
drivers/net/skfp/pmf.c:87: warning: cast from pointer to integer of different size
...
Use the standard offsetof() macro instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Magnus Damm [Mon, 8 Sep 2008 05:02:56 +0000 (14:02 +0900)]
smc91x: fix nowait printout
Commit c4f0e76747e80578a8f7fddd82fd0ce8127bd2f8 added nowait platform
data support. The printout code was however not updated, so the value
of SMC_NOWAIT is still used. This patch makes sure that nowait is printed
accordingly to platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- the register is defined for the 8169 chipset only and there is
no 8169 beyond RTL_GIGA_MAC_VER_06.
- only the lower 3 bytes of the register are valid
tulip: Fix dead 21041 ethernet after ifconfig down
The de2104x did a pci_disable_device() in it's close function, but
the open function never does a pci_enable_device() and assumes that
the device is already enabled. Considering that downing the interface
is just a temporary thing the pci_disable_device() isn't a pretty good
idea and removing it from the close function just fixes the bug.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David S. Miller [Wed, 24 Sep 2008 03:47:22 +0000 (20:47 -0700)]
aoe: Fix OOPS after SKB queue changes.
Reported by Thomas Graf.
If we don't unlink the SKB from the queue when we send it
out in aoenet_xmit(), dev_hard_start_xmit() will see skb->next
as non-NULL and interpret this to mean the SKB is part of a
GSO segment list.
Add __skb_unlink() call to fix that.
Signed-off-by: David S. Miller <davem@davemloft.net>
pkt_sched: Remove the tx queue state check in qdisc_run()
The current check wrongly uses the state of one (currently the first)
tx queue for all tx queues in case of non-default qdiscs. This check
mainly prevented requeuing loop with __netif_schedule(), but now it's
controlled inside __qdisc_run(), while dequeuing. The wrongness of
this check was first noticed by Herbert Xu.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pkt_sched: Check the state of tx_queue in dequeue_skb()
Check in dequeue_skb() the state of tx_queue for requeued skb to save
on locking and re-requeuing, and possibly remove the current check in
qdisc_run(). Based on the idea of Alexander Duyck.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for keeping an additional character alias
associated with an network interface. This is useful for maintaining
the SNMP ifAlias value which is a user defined value. Routers use this
to hold information like which circuit or line it is connected to. It
is just an arbitrary text label on the network device.
There are two exposed interfaces with this patch, the value can be
read/written either via netlink or sysfs.
This could be maintained just by the snmp daemon, but it is more
generally useful for other management tools, and the kernel is good
place to act as an agreed upon interface to store it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phonet endpoints are bound to individual ports.
This provides a /proc/sys/net/phonet (or sysctl) interface for
selecting the range of automatically allocated ports (much like the
ip_local_port_range with IPv4).
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 23 Sep 2008 02:48:19 +0000 (19:48 -0700)]
ipsec: Fix xfrm_state_walk race
As discovered by Timo Teräs, the currently xfrm_state_walk scheme
is racy because if a second dump finishes before the first, we
may free xfrm states that the first dump would walk over later.
This patch fixes this by storing the dumps in a list in order
to calculate the correct completion counter which cures this
problem.
I've expanded netlink_cb in order to accomodate the extra state
related to this. It shouldn't be a big deal since netlink_cb
is kmalloced for each dump and we're just increasing it by 4 or
8 bytes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware blob looks like this...
__le16 load_address
unsigned char data[]
[akpm@linux-foundation.org: include vmalloc.h] Signed-off-by: Jaswinder Singh <jaswinder@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 23 Sep 2008 02:24:45 +0000 (19:24 -0700)]
net/atm/lec.c: drop code after return
The break after the return serves no purpose.
Signed-off-by: Julia Lawall <julia@diku.dk> Reviewed-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 23 Sep 2008 02:22:58 +0000 (19:22 -0700)]
drivers/atm: Use DIV_ROUND_UP
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
In the case of the file drivers/atm/eni.c, I am a little bit suspicious of
the -1 at the end of the affected expression. Please check that that is
what is wanted.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Tue, 23 Sep 2008 02:21:51 +0000 (19:21 -0700)]
hci_usb: replace mb with smp_mb
smp_mb is enough for ordering memory operations among processors,and mb is
more expensive than smp_mb for UP machine, so replace it with smp_mb().
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Tue, 23 Sep 2008 02:20:51 +0000 (19:20 -0700)]
net: em_cmp.c use unaligned access helpers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Use "[%04x:%04x]" for PCI vendor/device IDs to follow the format used by
lspci(8).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove noop VFS stubs. The VFS does that on a NULL pointer anyways.
- Fix timer handler prototype to be correct
- Comment ugly SMP race I didn't fix.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Tue, 23 Sep 2008 02:16:51 +0000 (19:16 -0700)]
mISDN: annotate iomem pointer and add statics
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Tue, 23 Sep 2008 02:16:20 +0000 (19:16 -0700)]
mISDN: endian annotations for struct zt
Found two possible bugs where the z1 value was used directly without
byteswapping.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
After calling capi_ctr_get, error handling code should call capi_ctr_put.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r@
expression x,E;
statement S;
position p1,p2,p3;
@@
(
if ((x = capi_ctr_get@p1(...)) == NULL || ...) S
|
x = capi_ctr_get@p1(...)
... when != x
if (x == NULL || ...) S
)
<...
if@p3 (...) { ... when != capi_ctr_put(x)
when != if (x) { ... capi_ctr_put(x); ...}
return@p2 ...;
}
...>
(
return x;
|
return 0;
|
x = E
|
E = x
|
capi_ctr_put(x)
)
@exists@
position r.p1,r.p2,r.p3;
expression x;
int ret != 0;
statement S;
@@
* x = capi_ctr_get@p1(...)
<...
* if@p3 (...)
S
...>
* return@p2 \(NULL\|ret\);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kaihui Luo [Tue, 23 Sep 2008 02:02:36 +0000 (19:02 -0700)]
netfilter: xt_time gives a wrong monthday in a leap year
The function localtime_3 in xt_time.c gives a wrong monthday in a leap
year after 28th 2. calculating monthday should use the array
days_since_leapyear[] not days_since_year[] in a leap year.
Signed-off-by: Kaihui Luo <kaih.luo@gmail.com> Acked-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Quetchenbach [Sun, 21 Sep 2008 07:21:51 +0000 (00:21 -0700)]
tcp: advertise MSS requested by user
I'm trying to use the TCP_MAXSEG option to setsockopt() to set the MSS
for both sides of a bidirectional connection.
man tcp says: "If this option is set before connection establishment, it
also changes the MSS value announced to the other end in the initial
packet."
However, the kernel only uses the MTU/route cache to set the advertised
MSS. That means if I set the MSS to, say, 500 before calling connect(),
I will send at most 500-byte packets, but I will still receive 1500-byte
packets in reply.
This is a bug, either in the kernel or the documentation.
This patch (applies to latest net-2.6) reduces the advertised value to
that requested by the user as long as setsockopt() is called before
connect() or accept(). This seems like the behavior that one would
expect as well as that which is documented.
I've tried to make sure that things that depend on the advertised MSS
are set correctly.
Signed-off-by: Tom Quetchenbach <virtualphtn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log