Avoid restarting McBSP hardware after every DMA transfer to OMAP audio
devices on OMAP310, restart only DMA. Also avoid trying to link DMA
channels together as this feature isn't supported on 310 processors.
Apply on top of "[PATCH 1/5] Change all omap15xx devices to use
similar DMA handling than h6300 uses".
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mika Laitio [Tue, 12 Sep 2006 11:56:10 +0000 (14:56 +0300)]
[PATCH] Change all omap15xx devices to use similar DMA handling than h6300 uses
Change all omap15xx devices to use similar DMA handling than h6300 uses.
Thanks for the James Selvam for verifying this with omap 1510 innovator.
http://linux.omap.com/pipermail/linux-omap-open-source/2006-May/007256.html
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP: GPIO: IRQSTATUS2 workaround for retention state
In OMAP2420, an incoming GPIO interrupt always sets both GPIO_IRQSTATUS1
and GPIO_IRQSTATUS2, even if the relevant bit is disabled in
GPIO_IRQENABLE1/2 and DSP doesn't use GPIO at all. GPIO_IRQSTATUS1
is for MPU and GPIO_IRQSTATUS2 is for DSP. If IRQSTATUS is set, this
will prevent the system from going to idle state. This patch also clears
IRQSTATUS2 to avoid the above situation.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
David Brownell [Fri, 8 Sep 2006 10:56:11 +0000 (13:56 +0300)]
MUSB: Add more TUSB endpoints
Add a new fifo configuration that makes better use of the memory
available for use as TUSB fifos, and all the endpoint hardware.
Now almost every endpoint is available, and that's the default
setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Fri, 8 Sep 2006 07:48:43 +0000 (10:48 +0300)]
MUSB: PM cleanup
Second pass over TUSB power related code:
- Add new field in board-specific platform data, giving a nonzero floor to
the amount of VBUS power that peripherals could draw; pass that to the
platform code.
- Implement the call letting gadget drivers say how much VBUS power their
current configuration may draw, and use that to initialize appropriately
(pure-peripheral vs OTG modes) on USB reset and disconnect.
- Provide TUSB-specific hook into OTG transceiver logic to support that
VBUS call; and _only_ change the VBUS usage through that call.
- Remove obsolete comment and bitmask declarations.
On one board I measured 36 mA (at 5.1V) coming from VBUS not the battery
using the default gadget drivers in non-OTG TUSB configuration.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Wed, 6 Sep 2006 13:48:15 +0000 (16:48 +0300)]
MUSB: TUSB PM cleanup
Start updating the TUSB power related code ... first pass, use the chip's
idle mode whenever the USB link is inactive (disconnected or suspended).
That rule applies to both host and peripheral roles, and saves a fair
amount of power (50mA at 3.3V, etc).
Plus some cleanups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Juha Yrjola [Tue, 5 Sep 2006 17:59:30 +0000 (20:59 +0300)]
ARM: OMAP: Add write memory barriers to OMAP2 clock code
After adjusting clock parameters, OMAP2 CPUs need a memory
barrier to make sure the changes go into effect immediately.
Otherwise bad things will happen if we try to access the
peripheral whose clock is just being enabled.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Mika Laitio [Tue, 5 Sep 2006 15:17:13 +0000 (18:17 +0300)]
[PATCH] Add gsm phone support for the mixer in tsc2101 alsa driver
Add gsm phone support for the mixer in tsc2101 alsa driver. This allows
selecting cellphone for the playback target via alsa mixer interface.
Selection will connect gsm module to speaker and microphone allowing the
user to speak to phone and listen the opponents voice. Tested in ipaq
h63xx by using gomunicator as an application. Tux wanna call home, and
now Tux can finally call home :-)
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mika Laitio [Tue, 5 Sep 2006 15:12:57 +0000 (18:12 +0300)]
[PATCH] Fix init warning in tsc2101 alsa driver
Fix init warning in tsc2101 alsa driver. WARNING:
sound/arm/omap/snd-omap-alsa-tsc2101.o - Section mismatch: reference to
.init.text: from .data between '' (at offset 0x6c) and
'tsc2101_snd_omap_alsa_capture'
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
[PATCH] ARM: OMAP: Add Amstrad Delta platform bits for framebuffer
This patch adds the platform file components for the Amstrad Delta LCD
framebuffer. I have confirmed it works with latest git. The patch to
clock.c /is/ needed for this to work.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com>
[PATCH] ARM: OMAP: Register LCD backlight on PalmTE
Add the backlight device to the list of platform devices to register
on the Palm Tungsten E board. In the same way the device can be added
in other board files if a board has a single LCD with the backlight
controlled by OMAP PWL module.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a driver for the PWL module of OMAP CPUs in the Linux
backlight API. The driver allows changing the backlight instensity and
switching it off when system goes idle. The declaration of struct
omap_backlight_config is sent in a separate patch.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Prevent keyboard interrupt from staying masked when omap-keypad driver
is suspended to allow this interrupt to trigger a system wake up.
Locks are used as suggested by Juha Yrjölä.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/dsp/dsp_common.c: In function
'dsp_cpustat_update':
arch/arm/plat-omap/dsp/dsp_common.c:317: warning: implicit
declaration of function 'enable_irq'
arch/arm/plat-omap/dsp/dsp_common.c:325: warning: implicit
declaration of function 'disable_irq'
arch/arm/plat-omap/dsp/task.c: In function 'dsp_task_write_bk':
arch/arm/plat-omap/dsp/task.c:1232: warning: implicit
declaration of function 'disable_irq'
arch/arm/plat-omap/dsp/task.c:1232: warning: implicit
declaration of function 'enable_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
[PATCH] powerpc: Fix typo in powermac platform functions
New sparse caught that typo which could have caused erratic hardware
behaviour on some machines if the platform functions are used by the
firmware to change bits in some FCR registers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: constify some serial structs
[SERIAL] Make uart_match_port() work with all memory mapped UARTs
[PATCH] eligible_child: remove an obsolete ->tgid check
It is not possible to find a sub-thread in ->children/->ptrace_children
lists, ptrace_attach() does not allow to attach to sub-threads.
Even if it was possible to ptrace the task from the same thread group,
we can't allow to release ->group_leader while there are others (ptracer)
threads in the same group.
Resolve ARM1136 VIPT non-aliasing cache coherency issues observed when
using ptrace to set breakpoints and cleanup copy_{to,from}_user_page()
while we're here as requested by Russell King because "it's also far
too heavy on non-v6 CPUs".
NOTES:
1. Only access_process_vm() calls copy_{to,from}_user_page().
2. access_process_vm() calls get_user_pages() to pin down the "page".
3. get_user_pages() calls flush_dcache_page(page) which ensures cache
coherency between kernel and userspace mappings of "page". However
flush_dcache_page(page) may not invalidate I-Cache over this range
for all cases, specifically, I-Cache is not invalidated for the VIPT
non-aliasing case. So memory is consistent between kernel and user
space mappings of "page" but I-Cache may still be hot over this
range. IOW, we don't have to worry about flush_cache_page() before
memcpy().
4. Now, for the copy_to_user_page() case, after memcpy(), we must flush
the caches so memory is consistent with kernel cache entries and
invalidate the I-Cache if this mm region is executable. We don't
need to do anything after memcpy() for the copy_from_user_page()
case since kernel cache entries will be invalidated via the same
process above if we access "page" again. The flush_ptrace_access()
function (borrowed from SPARC64 implementation) is added to handle
cache flushing after memcpy() for the copy_to_user_page() case.
Signed-off-by: George G. Davis <gdavis@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
uhci-hcd: fix list access bug
USB: Support for ELECOM LD-USB20 in pegasus
USB: Add VIA quirk fixup for VT8235 usb2
USB: rtl8150_disconnect() needs tasklet_kill()
USB Storage: unusual_devs.h for Sony Ericsson M600i
USB Storage: Remove the finecam3 unusual_devs entry
UHCI: don't stop at an Iso error
usb gadget: g_ether spinlock recursion fix
USB: add all wacom device to hid-core.c blacklist
hid-core.c: Adds all GTCO CalComp Digitizers and InterWrite School Products to blacklist
USB floppy drive SAMSUNG SFD-321U/EP detected 8 times
Since vma->vm_pgoff is in units of smallpages, VMAs for huge pages have the
lower HPAGE_SHIFT - PAGE_SHIFT bits always cleared, which results in badd
offsets to the interleave functions. Take this difference from small pages
into account when calculating the offset. This does add a 0-bit shift into
the small-page path (via alloc_page_vma()), but I think that is negligible.
Also add a BUG_ON to prevent the offset from growing due to a negative
right-shift, which probably shouldn't be allowed anyways.
Tested on an 8-memory node ppc64 NUMA box and got the interleaving I
expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by: Adam Litke <agl@us.ibm.com> Cc: Andi Kleen <ak@muc.de> Acked-by: Christoph Lameter <clameter@engr.sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problems fixed are:
- Call to default_hwif_mmiops() was not being done until _after_
first IO operation, resulting in the first IO operation being
done as a port IO op, instead of memio.
- request_region() calls needed to be request_mem_region()
- Incomplete error case handling.
- Non-usage of ioremap() and __iomem.
Signed-off-by: John Keller <jpk@sgi.com> Signed-off-by: Jeremy Higdon <jeremy@sgi.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The port to genirq & the new powerpc interrupt model in 2.6.18 introduced a
bug in the legacy PowerMac PIC code (used on older machines) because of a
typo potentially causing hangs due to interrupt storms. This fixes it,
along with a performance issue causing us to do spurrious retriggers after
masking an interrupt.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The via-pmu backlight code (introduced in 2.6.18) has various design issues
causing crashes on machines using it like the old Wallstreet powerbook
(Michael, the author, never managed to test on these and I just got my hand
on one of those old beasts).
This fixes them by no longer trying to hijack the backlight device of the
frontmost framebuffer (causing that framebuffer to crash) but having it's
own local bits instead. Might look weird but it's better that way on those
old machines, at least as a last-minute fix for 2.6.18. We might rework
the whole thing later. This patch also changes the way it gets notified of
sleep and wakeup in order to properly shut the backlight down on sleep and
bring it back on wakeup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Mironchik [Fri, 1 Sep 2006 04:27:47 +0000 (21:27 -0700)]
[PATCH] dm: work around mempool_alloc, bio_alloc_bioset deadlocks
This patch works around a complex dm-related deadlock/livelock down in the
mempool allocator.
Alasdair said:
Several dm targets suffer from this.
Mempools are not yet used correctly everywhere in device-mapper: they can
get shared when devices are stacked, and some targets share them across
multiple instances. I made fixing this one of the prerequisites for this
patch:
which in some cases makes people more likely to hit the problem.
There's been some progress on this recently with (unfinished) dm-crypt
patches at:
http://www.kernel.org/pub/linux/kernel/people/agk/patches/2.6/editing/
(dm-crypt-move-io-to-workqueue.patch plus dependencies)
and:
I've no problems with a temporary workaround like that, but Milan Broz (a
new Redhat developer in the Czech Republic) has started reviewing all the
mempool usage in device-mapper so I'm expecting we'll soon have a proper fix
for this associated problems. [He's back from holiday at the start of next
week.]
For now, this sad-but-safe little patch will allow the machine to recover.
[akpm@osdl.org: rewrote changelog] Cc: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] IPMI: fix occasional oops on module unload
Olaf Kirch of SuSE tracked down a problem where module unloads of the IPMI
driver would occasionally result in Oopses. He tracked that down to a
variable that wasn't always initialized properly in some situations. This
patch initializes that variable. Olaf sent a patch that kzalloc-ed the
data, but this structure is large enough that I would perfer to not do
that. Thanks Olaf!
Signed-off-by: Corey Minyard <minyard@acm.org> Cc: Olaf Kirch <okir@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Olaf Hering [Fri, 1 Sep 2006 04:27:41 +0000 (21:27 -0700)]
[PATCH] exit early in floppy_init when no floppy exists
modprobe -v floppy on a Apple G5 writes incorrect stuff to dmesg:
Floppy drive(s): fd0 is 2.88M
The reason is that the legacy io check happens very late,
when part of the floppy stuff is already initialized.
check_legacy_ioport() returns either -ENODEV right away, or it walks
the device-tree looking for a floppy node.
Signed-off-by: Olaf Hering <olaf@aepfle.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup allocation and freeing of tsk->delays used by delay accounting.
This solves two problems reported for delay accounting:
1. oops in __delayacct_blkio_ticks
http://www.uwsg.indiana.edu/hypermail/linux/kernel/0608.2/1844.html
Currently tsk->delays is getting freed too early in task exit which can
cause a NULL tsk->delays to get accessed via reading of /proc/<tgid>/stats.
The patch fixes this problem by freeing tsk->delays closer to when
task_struct itself is freed up. As a result, it also eliminates the use of
tsk->delays_lock which was only being used (inadequately) to safeguard
access to tsk->delays while a task was exiting.
2. Possible memory leak in kernel/delayacct.c
http://www.uwsg.indiana.edu/hypermail/linux/kernel/0608.2/1389.html
The patch cleans up tsk->delays allocations after a bad fork which was
missing earlier.
The patch has been tested to fix the problems listed above and stress
tested with rapid calls to delay accounting's taskstats command interface
(which is the other path that can access the same data, besides the /proc
interface causing the oops above).
john stultz [Fri, 1 Sep 2006 04:27:37 +0000 (21:27 -0700)]
[PATCH] Fix faulty HPET clocksource usage (fix for bug #7062)
Apparently some systems export valid HPET addresses, but hpet_enable()
fails. Then when the HPET clocksource starts up, it only checks for a
valid HPET address, and the result is a system where time does not advance.
See http://bugme.osdl.org/show_bug.cgi?id=7062 for details.
This patch just makes sure we better check that the HPET is functional
before registering the HPET clocksource.
Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix receive tty error handling in synclink_gt driver. Adrian reported
compiler warning for incorrect bit test against char variable. I
determined these and other device specific error bits were incorrectly
defined.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] md: Fix issues with referencing rdev in md/raid1
We need to be careful when referencing mirrors[i].rdev. It can disappear
under us at various times.
So:
fix a couple of problem places.
comment a couple of non-problem places
move an 'atomic_add' which deferences rdev down a little
way to some where where it is sure to not be NULL.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] ZVC: Scale thresholds depending on the size of the system
The ZVC counter update threshold is currently set to a fixed value of 32.
This patch sets up the threshold depending on the number of processors and
the sizes of the zones in the system.
With the current threshold of 32, I was able to observe slight contention
when more than 130-140 processors concurrently updated the counters. The
contention vanished when I either increased the threshold to 64 or used
Andrew's idea of overstepping the interval (see ZVC overstep patch).
However, we saw contention again at 220-230 processors. So we need higher
values for larger systems.
But the current default is already a bit of an overkill for smaller
systems. Some systems have tiny zones where precision matters. For
example i386 and x86_64 have 16M DMA zones and either 900M ZONE_NORMAL or
ZONE_DMA32. These are even present on SMP and NUMA systems.
The patch here sets up a threshold based on the number of processors in the
system and the size of the zone that these counters are used for. The
threshold should grow logarithmically, so we use fls() as an easy
approximation.
Results of tests on a system with 1024 processors (4TB RAM)
The following output is from a test allocating 1GB of memory concurrently
on each processor (Forking the process. So contention on mmap_sem and the
pte locks is not a factor):
Increments and decrements are usually grouped rather than mixed. We can
optimize the inc and dec functions for that case.
Increment and decrement the counters by 50% more than the threshold in
those cases and set the differential accordingly. This decreases the need
to update the atomic counters.
The idea came originally from Andrew Morton. The overstepping alone was
sufficient to address the contention issue found when updating the global
and the per zone counters from 160 processors.
Also remove some code in dec_zone_page_state.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Stern [Thu, 31 Aug 2006 18:18:39 +0000 (14:18 -0400)]
uhci-hcd: fix list access bug
When skipping to the last TD of an URB, go to the _last_ entry in the
list instead of the _first_ entry (as780). This fixes Bugzilla #6747
and possibly others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Hindley [Mon, 28 Aug 2006 19:43:25 +0000 (20:43 +0100)]
USB: Add VIA quirk fixup for VT8235 usb2
Patch to add VIA PCI quirk for Enhanced/Extended USB on VT8235
southbridge. It is needed in order to use EHCI/USB 2.0 with ACPI.
Without it IRQs are not routed correctly, you get an "Unlink after
no-IRQ?" error and the device is unusable.
I belive this could also be a fix for Bugzilla Bug 5835.
Signed-off-by: Mark Hindley <mark@hindley.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz [Thu, 24 Aug 2006 04:11:01 +0000 (21:11 -0700)]
USB Storage: Remove the finecam3 unusual_devs entry
This patch removes the Kyocera Finecam L3 entry in unusual devices
originally submitted by Michael Krauth <michael.krauth@web.de> and
Alessandro Fracchetti <al.fracchetti@tin.it> given that Gerriet
<ger.haw@gmx.de> finds he doesn't need it and Alessandro confirms it
isn't needed anymore as well.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Aug 2006 15:58:50 +0000 (11:58 -0400)]
UHCI: don't stop at an Iso error
Unlike other sorts of endpoint queues, Isochronous queues don't stop
when an error is encountered. This patch (as772) fixes the scanning
routine in uhci-hcd, to make it keep on going when it finds an Iso
error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 21 Aug 2006 22:26:38 +0000 (15:26 -0700)]
usb gadget: g_ether spinlock recursion fix
The new spinlock debug code turned up a spinlock recursion bug in the
Ethernet gadget driver on a disconnect path; it would show up with any
UDC driver where the cancellation of active requests was synchronous,
rather than e.g. delayed until a controller's completion IRQ.
That recursion is fixed here by creating and using a new spinlock to
protect the relevant lists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roland Dreier [Thu, 31 Aug 2006 23:43:06 +0000 (16:43 -0700)]
IB/mthca: Use IRQ safe locks to protect allocation bitmaps
It is supposed to be OK to call mthca_create_ah() and mthca_destroy_ah()
from any context. However, for mem-full HCAs, these functions use the
mthca_alloc() and mthca_free() bitmap helpers, and those helpers use
non-IRQ-safe spin_lock() internally. Lockdep correctly warns that
this could lead to a deadlock. Fix this by changing mthca_alloc() and
mthca_free() to use spin_lock_irqsave().
Wei Dong [Thu, 31 Aug 2006 22:24:48 +0000 (15:24 -0700)]
[IPV4]: Fix SNMPv2 "ipFragFails" counter error
When I tested Linux kernel 2.6.17.7 about statistics
"ipFragFails",found that this counter couldn't increase correctly. The
criteria is RFC2011:
RFC2011
ipFragFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that have been discarded because
they needed to be fragmented at this entity but could not
be, e.g., because their Don't Fragment flag was set."
::= { ip 18 }
When I send big IP packet to a router with DF bit set to 1 which need to
be fragmented, and router just sends an ICMP error message
ICMP_FRAG_NEEDED but no increments for this counter(in the function
ip_fragment).
Signed-off-by: Wei Dong <weid@nanjing-fnst.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log