Magnus Damm [Thu, 19 Mar 2009 10:10:44 +0000 (10:10 +0000)]
sh: sh-rtc invalid time rework
This patch modifies invalid time handling in the
SuperH RTC driver. Instead of zeroing the returned
value at read-out time we just return an error code
and reset invalid values during probe.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 19 Mar 2009 10:05:58 +0000 (10:05 +0000)]
sh: sh-rtc carry interrupt rework
This patch modifies the SuperH RTC driver to only
enable carry interrupts when needed. So by default
no interrupts are enabled with this patch. Without
this patch a suspending system will most likely
wake up by the carry interrupt regardless if the
alarm interrupt has been enabled or not.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 19 Mar 2009 10:04:29 +0000 (10:04 +0000)]
sh: disallow kexec virtual entry
Older versions of kexec-tools has a zImage loader that
passes a virtual address as entry point. The elf loader
otoh it passes a physical address as entry point, and
pages are always passed as physical addresses as well.
Only allow physical addresses from now on.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Wed, 18 Mar 2009 10:06:15 +0000 (19:06 +0900)]
sh: kexec: Drop SR.BL bit toggling.
For the time being, this creates far more problems than it solves,
evident by the second local_irq_disable(). Kill all of this off
and rely on IRQ disabling to protect against the VBR reload.
Magnus Damm [Wed, 18 Mar 2009 08:51:29 +0000 (08:51 +0000)]
sh: add kexec jump support
Add kexec jump support to the SuperH architecture.
Similar to the x86 implementation, with the following
exceptions:
- Instead of separating the assembly code flow into
two parts for regular kexec and kexec jump we use a
single code path. In the assembly snippet regular
kexec is just kexec jump that never comes back.
- Instead of using a swap page when moving data between
pages the page copy assembly routine has been modified
to exchange the data between the pages using registers.
- We walk the page list twice in machine_kexec() to
do and undo physical to virtual address conversion.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 18 Mar 2009 08:49:45 +0000 (08:49 +0000)]
sh: rework kexec segment code
Rework the kexec code to avoid using P2SEG. Instead
we walk the page list in machine_kexec() and convert
the addresses from physical to virtual using C.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 17 Mar 2009 12:19:49 +0000 (21:19 +0900)]
sh: Flush only the needed range when unmapping a VMA.
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
Paul Mundt [Tue, 17 Mar 2009 08:49:49 +0000 (17:49 +0900)]
sh: Support for extended ASIDs on PTEAEX-capable SH-X3 cores.
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Paul Mundt [Tue, 17 Mar 2009 00:30:36 +0000 (09:30 +0900)]
sh: dma: Make PVR2 DMA configurable.
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
sh: Move IRQ multi definition of DMAC to defconfig
When SuperH CPU has IRQ multi of DMAC, SH_DMA_IRQ_MULTI becomes enable.
The following CPU's are Multi IRQ of DMAC now.
- SH775X and SH7091
- SH776X
- SH7780
- SH7785
If SH_DMA_IRQ_MULTI becomes enable, dma-sh api driver is optimized
for Multi IRQ.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 13 Mar 2009 15:36:55 +0000 (15:36 +0000)]
video: sh_mobile_lcdcfb suspend/resume support
This patch adds suspend/resume support to the LCDC
driver for SuperH Mobile - sh_mobile_lcdcfb.
We simply stop hardware on suspend and start it again
on resume. For RGB panels this is trivial, but for SYS
panels in deferred io mode this becomes a bit more
difficult - we need to wait for a frame end interrupt
to make sure the clocks are balanced before stopping
the actual hardware.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 13 Mar 2009 15:23:04 +0000 (15:23 +0000)]
sh: SuperH Mobile suspend support
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 11 Mar 2009 08:14:26 +0000 (08:14 +0000)]
sh: improve sh7785lcr power off code
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the Sega Dreamcast visual memory unit as a
flash mapping. It requires changes in the maple bus driver (posted
separately) to support block reads and writes.
The VMU is a 'smart' flash device, with a built-in 8-bit controller -
for instance there is an erase before a write but it is hidden from the
user. But the device's overall behaviour means it works well with the
mtd layer and it is appropriate to add it as an mtd mapping.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk> Acked-By: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh: Support fixed 32-bit PMB mappings from bootloader.
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 10 Mar 2009 06:24:21 +0000 (06:24 +0000)]
input: add suspend wakeup support to sh_keysc
This patch adds wakeup support to the sh_keysc driver.
With this feature the ".../power/wakeup" file can be
used to enable and disable if the device takes the
system out of suspend. Default is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 10 Mar 2009 06:08:49 +0000 (06:08 +0000)]
video: deferred io cleanup fix for sh_mobile_lcdcfb
Fix deferred io cleanup patch in the sh_mobile_lcdcfb driver.
If probe() fails early the sh_mobile_lcdc_stop() function will
be called to clean up deferred io. This patch modifies the
code to only call fb_deferred_io_cleanup() after deferred io
has been initialized.
With this patch applied we no longer hit BUG_ON() inside
fb_deferred_io_cleanup(). Triggers on a Migo-R with the
SYS QVGA panel board unmounted.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh: Add media/soc_camera.h to board setup of Renesas AP325RXA
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d76f83213e379b12df504269d21c9e7c) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CLONE_PARENT can fool the ->self_exec_id/parent_exec_id logic. If we
re-use the old parent, we must also re-use ->parent_exec_id to make
sure exit_notify() sees the right ->xxx_exec_id's when the CLONE_PARENT'ed
task exits.
Also, move down the "p->parent_exec_id = p->self_exec_id" thing, to place
two different cases together.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Roland McGrath <roland@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Howells <dhowells@redhat.com> Cc: Serge E. Hallyn <serge@hallyn.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
Chris Mason [Mon, 9 Mar 2009 15:45:38 +0000 (11:45 -0400)]
Btrfs: fix spinlock assertions on UP systems
btrfs_tree_locked was being used to make sure a given extent_buffer was
properly locked in a few places. But, it wasn't correct for UP compiled
kernels.
This switches it to using assert_spin_locked instead, and renames it to
btrfs_assert_tree_locked to better reflect how it was really being used.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Reason for this is that cpu time accounting usually only happens from
interrupt context, but acct_update_integrals gets also called from
process context with interrupts enabled.
So in acct_update_integrals we may end up with the following scenario:
Between reading tsk->stime/tsk->utime and tsk->acct_timexpd an interrupt
happens which updates accouting values. This causes acct_timexpd to be
greater than the former stime + utime. The subsequent calculation of
dtime = cputime_sub(time, tsk->acct_timexpd);
will be negative and the division performed by
cputime_to_jiffies(dtime)
will generate an exception since the result won't fit into a 32 bit
register.
In order to fix this just always disable interrupts while accessing any
of the accounting values.
Reported by: Frans Pop <elendil@planet.nl>
Tested by: Frans Pop <elendil@planet.nl> Cc: stable@kernel.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 8 Mar 2009 17:27:13 +0000 (10:27 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pebs: correct qualifier passed to ds_write_config() from ds_request_pebs()
x86, bts: remove bad warning
x86: add Dell XPS710 reboot quirk
x86, math-emu: fix init_fpu for task != current
x86: EFI: Back efi_ioremap with init_memory_mapping instead of FIX_MAP
x86: fix DMI on EFI
Linus Torvalds [Sun, 8 Mar 2009 17:24:39 +0000 (10:24 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (28 commits)
Blackfin arch: SPI_MMC is now mainlined MMC_SPI
Blackfin arch: disable legacy /proc/scsi/ support by default
Blackfin arch: remove duplicated ANOMALY_05000448 ifdef check
Blackfin arch: add stubs for anomalies 447 and 448
Blackfin arch: cleanup bfin_sport.h header and export it to userspace
Blackfin arch: fix bug - gdb signull case make trunk kernel panic frequently
Blackfin arch: remove spurious dash when dcache is off
Blackfin arch: mark init_pda as __init as only __init funcs all it
Blackfin arch: fix bug - On bf548-ezkit, ethernet fails to work after wakeup from "mem"
Blackfin arch: Random read/write errors are a bad thing
Blackfin arch: update default kernel config, select KSZ8893M driver for BF518
Blackfin arch: Fix bug - KGDB single step into the middle of a 4 bytes instruction on bf561 after soft bp is hit
Blackfin arch: Fix bug - make ksz8893m driver available when bfin_mac is enabled
Blackfin arch: make sure people do not set the kernel load address too high
Blackfin arch: fix bug - The SPORT_HYS bit is not set for BF561 0.5
Blackfin arch: update anomaly sheets to match latest public info
Blackfin arch: Fix BUG - kernel fails to build in pm.c when allow wakeup fromi standby by GPIO
Blackfin arch: PM_BFIN_WAKE_GP: update help
Blackfin arch: fix bug - kgdb fails to continue after setting breakpoint on bf561-ezkit kernel with smp patch
Blackfin arch: Enable Write Back Cache on all Blackfin Boards
...
Linus Torvalds [Sun, 8 Mar 2009 17:23:05 +0000 (10:23 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmatest: fix use after free in dmatest_exit
ipu_idmac: fix spinlock type
iop-adma, mv_xor: fix mem leak on self-test setup failure
fsldma: fix off by one in dma_halt
I/OAT: fail self-test if callback test reaches timeout
I/OAT: update driver version and copyright dates
I/OAT: list usage cleanup
I/OAT: set tcp_dma_copybreak to 256k for I/OAT ver.3
I/OAT: cancel watchdog before dma remove
I/OAT: fail initialization on zero channels detection
I/OAT: do not set DCACTRL_CMPL_WRITE_ENABLE for I/OAT ver.3
I/OAT: add verification for proper APICID_TAG_MAP setting by BIOS
dmaengine: update kerneldoc
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ata: add CFA specific identify data words
remove stale comment from <linux/hdreg.h>
AT91: initialize Compact Flash on AT91SAM9263 cpu
ide: add at91_ide driver
ide: allow to wrap interrupt handler
ide-iops: fix odd-length ATAPI PIO transfers
ide: NULL noise: drivers/ide/ide-*.c
ide: expiry() returns int, negative expiry() return values won't be noticed
Linus Torvalds [Sun, 8 Mar 2009 17:22:01 +0000 (10:22 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Don't trust current capacity values in identify words 57-58
libata: make sure port is thawed when skipping resets
sata_nv: fix module parameter description
ahci: Add the Device IDs for MCP89 and remove IDs of MCP7B to/from ahci.c
libata: don't use on-stack sense buffer
libata: align ap->sector_buf
libata: fix dma_unmap_sg misuse
libata: change drive ready wait after hard reset to 5s
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
Squashfs: frag_size should be signed, as it can hold an error result
Squashfs: fix documentation typo, Cramfs filesystem limit is 256 MiB
Squashfs: Fix oops when reading fsfuzzer corrupted filesystems
Linus Torvalds [Sun, 8 Mar 2009 17:03:31 +0000 (10:03 -0700)]
Merge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix headphone-detect regression with multiple HP jacks
ALSA: hda - Fix typos in slave controls in patch_sigmatel.c
Ralf Baechle [Thu, 5 Mar 2009 10:45:48 +0000 (11:45 +0100)]
MIPS: compat: Implement is_compat_task.
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall
hole" (commit 5b1017404aea6d2e552e991b3fd814d839e9cd67). MIPS doesn't
have the issue that was fixed for x86-64 by that patch.
This also doesn't solve the N32 issue which is that N32 seccomp processes
will be treated as non-compat processes thus only have access to N64
syscalls.
Markus Metzger [Thu, 5 Mar 2009 07:57:21 +0000 (08:57 +0100)]
x86, pebs: correct qualifier passed to ds_write_config() from ds_request_pebs()
ds_write_config() can write the BTS as well as the PEBS part of
the DS config. ds_request_pebs() passes the wrong qualifier, which
results in the wrong configuration to be written.
Markus Metzger [Thu, 5 Mar 2009 07:49:54 +0000 (08:49 +0100)]
x86, bts: remove bad warning
In case a ptraced task is reaped (while the tracer is still attached),
ds_exit_thread() is called before ptrace_exit(). The latter will
release the bts_tracer and remove the thread's ds_ctx.
The former will WARN() if the context is not NULL.
Oleg Nesterov submitted patches that move ptrace_exit() before
exit_thread() and thus reverse the order of the above calls.
Remove the bad warning. I will add it again when Oleg's changes are in.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305084954.A22000@sedona.ch.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Takashi Iwai [Fri, 6 Mar 2009 08:43:58 +0000 (09:43 +0100)]
ALSA: hda - Fix headphone-detect regression with multiple HP jacks
The recent changes over the DAC detection mechanism in patch_sigmatel.c
breaks the HP detection on the machines with multiple HP jacks.
It's basically because of the workaround to support the multi-channel
output. Since the HP detection is more important feature, disable
the HP-swap workaroud temporarily.
Jens Axboe [Fri, 6 Mar 2009 07:55:24 +0000 (08:55 +0100)]
block: fix missing bio back/front segment size setting in blk_recount_segments()
Commit 1e42807918d17e8c93bf14fbb74be84b141334c1 introduced a bug where we
don't get front/back segment sizes in the bio in blk_recount_segments().
Fix this by tracking the back bio as well as the front bio in
__blk_recalc_rq_segments(), this also cleans up the interface by getting
rid of the segment size pointer passing.
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The tick rate define (ORION5X_TCLK) was removed in favor of a runtime
detection. The quick fix is to add the define in the watchdog driver.
The fix is not correct for all supported orion5x platforms, but since
the supported platforms right now are 133 Mhz and 166 Mhz, it won't
be _that_ far off. ;-) A fix that uses the runtime-determined timer
tick rate will be applied later.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: Kristof Provost <kristof@sigsegv.be> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Nicolas Pitre <nico@cam.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org>
Reinette Chatre [Tue, 3 Mar 2009 19:37:04 +0000 (11:37 -0800)]
iwlwifi: fix error flow in iwl*_pci_probe
Both the agn and 3945 drivers has some problems with dealing with
errors in their probe functions. Ensure that a goto will undo only
things that was done before the goto was called.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6-omap-h63xx.git / log