Manfred Spraul [Sun, 31 Aug 2008 17:58:49 +0000 (19:58 +0200)]
kernel/cpu.c: Move the CPU_DYING notifiers
When a cpu is taken offline, the CPU_DYING notifiers are called on the
dying cpu. According to <linux/notifiers.h>, the cpu should be "not
running any task, not handling interrupts, soon dead".
For the current implementation, this is not true:
- __cpu_disable can fail. If it fails, then the cpu will remain alive
and happy.
- At least on x86, __cpu_disable() briefly enables the local interrupts
to handle any outstanding interrupts.
What about moving CPU_DYING down a few lines, behind the __cpu_disable()
line?
There are only two CPU_DYING handlers in the kernel right now: one in
kvm, one in the scheduler. Both should work with the patch applied
[and: I'm not sure if either one handles a failing __cpu_disable()]
The patch survives simple offlining a cpu. kvm untested due to lack
of a test setup.
sched: fix __load_balance_iterator() for cfq with only one task
The __load_balance_iterator() returns a NULL when there's only one
sched_entity which is a task. It is caused by the following code-path.
/* Skip over entities that are not tasks */
do {
se = list_entry(next, struct sched_entity, group_node);
next = next->next;
} while (next != &cfs_rq->tasks && !entity_is_task(se));
if (next == &cfs_rq->tasks)
return NULL;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This will return NULL even when se is a task.
As a side-effect, there was a regression in sched_mc behavior since 2.6.25,
since iter_move_one_task() when it calls load_balance_start_fair(),
would not get any tasks to move!
Fix this by checking if the last entity was a task or not.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton [Fri, 5 Sep 2008 21:00:24 +0000 (14:00 -0700)]
drivers/mmc/card/block.c: fix refcount leak in mmc_block_open()
mmc_block_open() increments md->usage although it returns with -EROFS when
default mounting a MMC/SD card with write protect switch on. This
reference counting bug prevents /dev/mmcblkX from being released on card
removal, and situation worsen with reinsertion until the minor number
range runs out.
Reported-by: <sasin@solomon-systech.com> Acked-by: Pierre Ossman <drzeus-list@drzeus.cx> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atmel_lcdfb: fix oops in rmmod when framebuffer fails to register
If framebuffer registration failed in platform driver ->probe() callback,
dev_get_drvdata() points to freed memory region, but ->remove() function
try to use it and the following oops occurs:
Fix regression tracked as http://bugzilla.kernel.org/show_bug.cgi?id=11361
and caused by commit f735a2a1a4f2a0f5cd823ce323e82675990469e2 ("[netdrvr]
forcedeth: setup wake-on-lan before shutting down") that makes network
adapters integrated into the NVidia MCP55 chipsets fail to work in kexeced
kernels. The problem appears to be that if the adapter is put into D3_hot
during ->shutdown(), it cannot be brought back into D0 after kexec (ref.
http://marc.info/?l=linux-kernel&m=121900062814967&w=4). Therefore, only
put forcedeth into D3 during ->shutdown() if the system is to be powered
off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Ayaz Abdulla <aabdulla@nvidia.com> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Fri, 5 Sep 2008 21:00:18 +0000 (14:00 -0700)]
res_counter: fix off-by-one bug in setting limit
I found we can no longer set limit to 0 with 2.6.27-rcX:
# mount -t cgroup -omemory xxx /mnt
# mkdir /mnt/0
# echo 0 > /mnt/0/memory.limit_in_bytes
bash: echo: write error: Device or resource busy
It turned out 'limit' can't be set to 'usage', which is wrong IMO.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Acked-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix process time monotonicity
sched_clock: fix NOHZ interaction
* git://git.infradead.org/~dwmw2/dwmw2-2.6.27:
Revert "[ARM] use the new byteorder headers"
Fix conditional export of kvh.h and a.out.h to userspace.
[MTD] [NAND] tmio_nand: fix base address programming
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
V4L/DVB (8881): gspca: After 'while (retry--) {...}', retry will be -1 but not 0.
V4L/DVB (8880): PATCH: Fix parents on some webcam drivers
V4L/DVB (8877): b2c2 and bt8xx: udelay to mdelay
V4L/DVB (8876): budget: udelay changed to mdelay
V4L/DVB (8874): gspca: Adjust hstart for sn9c103/ov7630 and update usb-id's.
V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.
V4L/DVB (8872): gspca: Bad image format and offset with rev072a of spca561.
V4L/DVB (8870): gspca: Fix dark room problem with sonixb.
V4L/DVB (8869): gspca: Move the Sonix webcams with TAS5110C1B from sn9c102 to gspca.
V4L/DVB (8868): gspca: Support for vga modes with sif sensors in sonixb.
V4L/DVB (8844): dabusb_fpga_download(): fix a memory leak
V4L/DVB (8843): tda10048_firmware_upload(): fix a memory leak
V4L/DVB (8842): vivi_release(): fix use-after-free
V4L/DVB (8840): dib0700: add basic support for Hauppauge Nova-TD-500 (84xxx)
V4L/DVB (8839): dib0700: add comment to identify 35th USB id pair
V4L/DVB (8837): dvb: fix I2C adapters name size
V4L/DVB (8835): gspca: Same pixfmt as the sn9c102 driver and raw Bayer added in sonixb.
V4L/DVB (8834): gspca: Have a bigger buffer for sn9c10x compressed images.
V4L/DVB (8833): gspca: Cleanup the sonixb code.
V4L/DVB (8832): gspca: Bad pixelformat of vc0321 webcams.
...
Merge branch 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acer-wmi: remove debugfs entries upon unloading
ACPI: Avoid bogus timeout about SMbus check
fujitsu-laptop: fix regression for P8010 in 2.6.27-rc
ACPI: Make Len Brown the ACPI maintainer again
ACPI: thinkpad-acpi: wan radio control is not experimental
PNPACPI: ignore the producer/consumer bit for extended IRQ descriptors
acpi: add checking for NULL early param
ACPI: Fix typo in "Disable MWAIT via DMI on broken Compal board"
ACPI: Fix now signed module parameter.
ACPI: Change package length error to warning
ACPI: Fix now signed module parameter.
Revert "mac80211: Use IWEVASSOCREQIE instead of IWEVCUSTOM"
This reverts commit 087d833e5a9f67ba933cb32eaf5a2279c1a5b47c, which was
reported to break wireless at least in some combinations with 32bit user
space and a 64bit kernel. Alex Williamnson bisected it to this commit.
Reported-and-bisected-by: Alex Williamson <alex.williamson@hp.com> Acked-by: John W. Linville <linville@tuxdriver.com> Cc: David Miller <davem@davemloft.net> Cc: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Spencer reported a problem where utime and stime were going negative despite
the fixes in commit b27f03d4bdc145a09fb7b0c0e004b29f1ee555fa. The suspected
reason for the problem is that signal_struct maintains it's own utime and
stime (of exited tasks), these are not updated using the new task_utime()
routine, hence sig->utime can go backwards and cause the same problem
to occur (sig->utime, adds tsk->utime and not task_utime()). This patch
fixes the problem
TODO: using max(task->prev_utime, derived utime) works for now, but a more
generic solution is to implement cputime_max() and use the cputime_gt()
function for comparison.
Peter Zijlstra [Mon, 1 Sep 2008 14:44:23 +0000 (16:44 +0200)]
sched_clock: fix NOHZ interaction
If HLT stops the TSC, we'll fail to account idle time, thereby inflating the
actual process times. Fix this by re-calibrating the clock against GTOD when
leaving nohz mode.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Tested-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Woodhouse [Fri, 5 Sep 2008 15:01:15 +0000 (16:01 +0100)]
Revert "[ARM] use the new byteorder headers"
This reverts commit ae82cbfc8beaa69007aa09966d3983ac938c3577. It
needs the new byteorder headers to be exported to userspace, and
they aren't yet -- and probably shouldn't be, at this point in the
2.6.27 release cycle (or ever, for that matter).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
async_tx: fix the bug in async_tx_run_dependencies
Should clear the next pointer of the TX if we are sure that the
next TX (say NXT) will be submitted to the channel too. Overwise,
we break the chain of descriptors, because we lose the information
about the next descriptor to run. So next time, when invoke
async_tx_run_dependencies() with TX, it's TX->next will be NULL, and
NXT will be never submitted.
Cc: <stable@kernel.org> [2.6.26] Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix conditional export of kvh.h and a.out.h to userspace.
Some architectures have moved the asm/ into arch/ and some have not.
This patch checks for a.out.h and kvh.h in both places before exporting
the corresponding file from linux/
[dwmw2: simplified a little] Signed-off-by: Khem Raj <raj.khem@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[MTD] [NAND] tmio_nand: fix base address programming
Fix offset of second word used for programming base address of memory
window. Also program tmio with offset of the FCR, not with physical
memory location.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Cc: Ian Molton <spyro@f2s.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Magnus Damm [Wed, 27 Aug 2008 09:33:56 +0000 (18:33 +0900)]
i2c: fix i2c-sh_mobile timing issues
This patch teaches the i2c-sh_mobile driver to make use of wait irqs.
Without this patch only dte irqs are used which may lead to overruns
and cases of missing stop and extra bytes being read on the i2c bus.
Use of wait irqs forces the hardware to pause and wait until the cpu
is ready. Polling is also reworked in this patch to fix ms delay issues.
Verified with bus analyzer and tested on MigoR and AP325RXA boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh: resume_kernel fix for kernel oops built with CONFIG_BKL_PREEMPT=y.
This patch fixes a problem within the SH implementation of resume_kernel code,
that implements in assembly the bulk of preempt_schedule_irq function without
taking care of the extra code needed to handle the BKL preemptible.
The patch basically consists of removing this asm code and calling the common
C implementation (see kernel/sched.c) as other archs do.
Another change is the missing 'cli' macro invocation at the beginning of
the resume_kernel.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Hans de Goede [Mon, 1 Sep 2008 18:28:23 +0000 (15:28 -0300)]
V4L/DVB (8880): PATCH: Fix parents on some webcam drivers
While doing some testing using Luca Risolia's sonix driver I noticed that
the video device did not get ACL's set to allow access by locally logged in
users, nor does it show up as a video device in lshal, causing cheese to not
see it.
This turns out to be caused by all of Luca Risolia's drivers not setting
the parent member of the video_device struct. This patch fixes this.
Cc: Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
b2c2-flexcop, dvb/bt8xx and video/bt8xx fails to build on ARM with:
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
Hans de Goede [Thu, 4 Sep 2008 19:22:57 +0000 (16:22 -0300)]
V4L/DVB (8874): gspca: Adjust hstart for sn9c103/ov7630 and update usb-id's.
- Adjust hstart in ov7630 on sn9c103 initdata to shift bayer pattern, this is
the same change as done for the other initdata tables in a previous patch.
- Assign usb-id's for the ov7630 + sn9c103 to gspca if gspca and sn9c102
drivers are both enabled.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 4 Sep 2008 19:22:57 +0000 (16:22 -0300)]
V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.
-Make raw bayer header size change from 20 to 16 affect rev072a only, my 2
rev012a cams both have a header size of 20
-While testing this I also tested the new exposure setting (good work on
finding the register JF), and after quite a bit of testing have found out the
exact meaning of the register, this patch modifies setexposure to control
the exposure over a much wider range.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 4 Sep 2008 19:22:56 +0000 (16:22 -0300)]
V4L/DVB (8870): gspca: Fix dark room problem with sonixb.
When using the sonixb driver in a dark room and given that the autoexposure
algorithm starts with a setting most suitable for daylight, the picture
produced by the cam may actually be 100% black leading to a avg_lum value of 0,
so an avg_lum value of 0 does not always signal an exposure settings change
(which it normally does). This patch adds a check for the really black image
case and stops dropping all frames as invalid in this case.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 4 Sep 2008 19:22:55 +0000 (16:22 -0300)]
V4L/DVB (8869): gspca: Move the Sonix webcams with TAS5110C1B from sn9c102 to gspca.
This patch makes gspca claim the USB-ID for sn9c101/2 cams with a TAS5110C1B
sensor even if both gspca and sn9c102 are enabled, as these cams are much
better supported under gspca (and extensively tested with gspca).
It also removes an usb-id from sn9c102 for one more unsupported bridge
sensor combo.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 4 Sep 2008 19:20:12 +0000 (16:20 -0300)]
V4L/DVB (8868): gspca: Support for vga modes with sif sensors in sonixb.
- Add documentation for some known registers
- Add support for vga modes (320x240, 160x120) for sif sensors
- Remove F_RAW sensor flag raw mode should work on any sensor as its a bridge
only thing and keeping the flag was becoming awkward.
- Fixup ov6650 and pas106 auto exposure window settings
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Zhao Yakui [Tue, 26 Aug 2008 05:57:34 +0000 (13:57 +0800)]
ACPI: Avoid bogus timeout about SMbus check
In the function of wait_transaction_complete when the timeout happens,
OS will try to check the status of SMbus again. If the status is what OS
expected, it will be regarded as the bogus timeout. Otherwise it will be
treated as ETIME.
Jonathan Woithe [Fri, 29 Aug 2008 01:36:21 +0000 (11:06 +0930)]
fujitsu-laptop: fix regression for P8010 in 2.6.27-rc
The following patch (based on a patch from Stephen Gildea) fixes a
regression with the LCD brightness keys on Fujitsu P8010 laptops which was
observed with the 2.6.27-rc series (basically they stopped working due to
changes within the fujitsu-laptop and video modules). Please apply to
2.6.27-rc and acpi git.
A more complete solution for this laptop will be included in an upcoming
patch, hopefully for 2.6.28. In the meantime this restores most
functionality for P8010 users.
Signed-off-by: Stephen Gildea <stepheng+fujitsu-laptop@gildea.com> Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au> Signed-off-by: Andi Kleen <ak@linux.intel.com>
PCI: fix pbus_size_mem() resource alignment for CardBus controllers
Commit 884525655d07fdee9245716b998ecdc45cdd8007 ("PCI: clean up resource
alignment management") changed the resource handling to mark how a
resource was aligned on a per-resource basis.
Thus, instead of looking at the resource number to determine whether it
was a bridge resource or a regular resource (they have different
alignment rules), we should just ask the resource for its alignment
directly.
The reason this broke only cardbus resources was that for the other
types of resources, the old way of deciding alignment actually still
happened to work. But CardBus bridge resources had been changed by
commit 934b7024f0ed29003c95cef447d92737ab86dc4f ("Fix cardbus resource
allocation") to look more like regular resources than PCI bridge
resources from an alignment handling standpoint.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calibration against PIT fails, the warning that we print is misleading.
In a virtualized environment the VM may get descheduled while calibration
or, the check in PIT calibration may fail due to other virtualization
overheads.
The warning message explicitly assumes that calibration failed due to SMI's
which may not be the case. Change that to something proper.
Signed-off-by: Alok N Kataria <akataria@vmware.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix for getting CPU number in power_save_ppc32_restore()
powerpc: Fix build error with 64K pages and !hugetlbfs
powerpc: Work around gcc's -fno-omit-frame-pointer bug
powerpc: Make sure _etext is after all kernel text
powerpc: Only make kernel text pages of linear mapping executable
powerpc: Fix uninitialised variable in VSX alignment code
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2x: Accessing un-mapped page
ath9k: Fix TX control flag use for no ACK and RTS/CTS
ath9k: Fix TX status reporting
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
iwlwifi: call apm stop on exit
iwlwifi: fix Tx cmd memory allocation failure handling
iwlwifi: fix rx_chain computation
iwlwifi: fix station mimo power save values
iwlwifi: remove false rxon if rx chain changes
iwlwifi: fix hidden ssid discovery in passive channels
iwlwifi: W/A for the TSF correction in IBSS
netxen: Remove workaround for chipset quirk
pcnet-cs, axnet_cs: add new IDs, remove dup ID with less info
ixgbe: initialize interrupt throttle rate
net/usb/pegasus: avoid hundreds of diagnostics
tipc: Don't use structure names which easily globally conflict.
Eric Paris [Wed, 3 Sep 2008 15:49:47 +0000 (11:49 -0400)]
SELinux: memory leak in security_context_to_sid_core
Fix a bug and a philosophical decision about who handles errors.
security_context_to_sid_core() was leaking a context in the common case.
This was causing problems on fedora systems which recently have started
making extensive use of this function.
In discussion it was decided that if string_to_context_struct() had an
error it was its own responsibility to clean up any mess it created
along the way.
Signed-off-by: Eric Paris <eparis@redhat.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: James Morris <jmorris@namei.org>
The allocated RX buffer size was 64 bytes bigger than the PCI mapped
size with no good reason. If the packet was actually using the buffer up
to its limit and if the last 64 bytes of the buffer crossed 4KB boundary
then an unmapped PCI page was accessed. The fix is to use only one
parameter for the buffer size - there is no need to differentiate
between the buffer size and the PCI mapping size since the extra 64
bytes can actually be used by the FW to align the Ethernet payload to
64 bytes.
Also updating the driver version and date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 3 Sep 2008 20:12:22 +0000 (17:12 -0300)]
V4L/DVB (8835): gspca: Same pixfmt as the sn9c102 driver and raw Bayer added in sonixb.
1) Lower the hstart setting for all sensor by 1 so that we generate
(compressed) BGGR data just like sn9c102 does (instead of GBRG data)
2) Add support for raw bayer output in the lowest resolutions (not enough
bandwidth for higher resolutions), this should work with all sensors but
to be sure only enable it for sensors where it has been tested.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Sep 2008 20:12:22 +0000 (17:12 -0300)]
V4L/DVB (8834): gspca: Have a bigger buffer for sn9c10x compressed images.
Under certain conditions sonixb compressed frame size can get bigger then
the uncompressed size (seen with 0c45:6028), so make the buffers slightly
bigger.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Sep 2008 20:12:21 +0000 (17:12 -0300)]
V4L/DVB (8833): gspca: Cleanup the sonixb code.
-the usb-id table caried several flags which were not usb-id specific but
sensor specific, add a sensor_data array and move these flag there
-fr_h_sz was being abused to store and check which bridge was being used
instead add a bridge member to the sd struct
-now that we have a sensor_data table use that to store pointers to
init_sequences instead of using switch cases on sd->sensor
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Sep 2008 20:12:20 +0000 (17:12 -0300)]
V4L/DVB (8831): gspca: Resolve webcam conflicts between some drivers.
-remove USB-id's from zc0301 for cams for which zc0301.c does not support
the sensor
-remove USB-id's from sn9c102 for cams where sn9c102 does not support the
bridge sensor combination
-no longer make inclusion of usb id's removed from zc0301 and sn9c102
conditional in gspca
-fix conditional inclusion of USB-id's in gspca to also work when the
conflicting drivers are build as a module
-add a number of USB-id's to gspca from various windows .inf files:
0c45:608f from generic sonix sn9c103 inf file (+ ov7630 which we support)
041e:4022 from creative webcam nx pro, same as already supported 041e:401e
0ac8:0301 from generic zc0301 driver which supports many sensors
10fd:804d from typhoon webshot driver (also FlyCAM-USB 300 plus)
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Sep 2008 20:12:17 +0000 (17:12 -0300)]
V4L/DVB (8825): gspca: More controls for pac73xx and new webcam 093a:2624.
-Add usb id for 093a:2624 (pac7302)
-Report some controls to userspace with 7302 only, as they are 7302 only
-Add gain and exposure controls
-Add autogain
-Fix 7302 imaged being mirrored by default
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Sep 2008 20:12:15 +0000 (17:12 -0300)]
V4L/DVB (8816): gspca: Set disabled ctrls and fix a register pb with ovxxxx in sonixb.
- set some controls as disabled instead of copying the device descr.
- in the ov6650 / 7650 exposure code clamp reg 11 before (instead of after)
using it to calculate reg 10.
- disable brightness (instead of ignoring it) for the TAS5110.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 3 Sep 2008 20:12:14 +0000 (17:12 -0300)]
V4L/DVB (8812): gspca: Do pac73xx webcams work.
- documentation for some registers
- some preparations for adding autogain_n_exposure functionality
- various pac7311 fixes
- disable brightness and colors controls for 7311
- fix contrast control for 7311
- add hflip and vflip controls for 7311
- minimal jpeg header
- proper SOF detection
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 3 Sep 2008 20:11:54 +0000 (17:11 -0300)]
V4L/DVB (8769): cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues()
cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues().
If accounting of a queue is in error, logic borrowed from ivtv will cause
an oops when flushing the queues for a stream. This change greatly
simplifies the queue flush logic, and sets the queue back to sane
defaults on a flush.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (8751): vivi: Fix some issues at vivi register routine
This patch fixes several small issues at vivi register routines:
1) minor and n_devs should be unsigned;
2) n_devs = 0 were not properly handled;
3) if n_devs specify a high number, the driver would just roll back and
won't register any device. The proper behaviour is to keep all succeded
devices registered;
4) both n_devs and minor were using 0 as permissions. Better to have
them with 0444.
With the current patch, if n_devs specify a very large value, it will
register all possible devices. For example, on a machine without any
other V4L drivers loaded, with this patch, we will have something like:
vivi: V4L2 device registered as /dev/video0
vivi: V4L2 device registered as /dev/video1
vivi: V4L2 device registered as /dev/video2
...
vivi: V4L2 device registered as /dev/video31
video_register_device_index: get_index failed
Video Technology Magazine Virtual Video Capture Board ver 0.5.0 successfully loaded.
5) The number of allocated devices on success is now kept at n_devs:
$ cat /sys/module/vivi/parameters/n_devs
32
Thanks to Henne <henne@nachtwindheim.de> for pointing that there were
some issues at vivi.
Cc: Henne <henne@nachtwindheim.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 10-08-08 23:37, Alan Cox wrote:
>
> Would probably make the printk "pms: not enabled, use pms.enable=1 to
> probe"
>
> So you know
> a) What is wittering about not being probed
> b) How to undo it.
>
> But thats trivia really.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rene Herman [Wed, 3 Sep 2008 19:48:21 +0000 (16:48 -0300)]
V4L/DVB (8727): V4L1: make PMS not autoprobe when builtin.
The old Mediavision Pro Movie Studio legacy ISA V4L1 driver was found to
hang the boot during Ingo Molnar's testing of randconfig kernels. Have it
require a "pms.enable=1" kernel parameter to enable the driver when
builtin which avoids such problems.
This is a deprecated and, very likely, unused driver. Nothing changes
modular behaviour moreover.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Simon Arlott [Wed, 3 Sep 2008 19:48:20 +0000 (16:48 -0300)]
V4L/DVB (8726): link tuner before saa7134
If saa7134_init is run before v4l2_i2c_drv_init (tuner), then
saa7134_board_init2 will try to set the tuner type for devices that don't
exist yet. This moves tuner to before all of the device-specific drivers
so that it's loaded early enough on boot.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / linux-2.6-omap-h63xx.git / log