Jouni Hogander [Mon, 30 Jun 2008 08:52:48 +0000 (11:52 +0300)]
OMAP: PM: Add new sysfs option for disabling clocks when entering idle
There are drivers that are not disabling their clocks (gpio &
uart). These clocks need to be disabled if retention/off state is
wanted when idling. Before disabling them in idle loop this option
needs to be checked.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Tue, 24 Jun 2008 07:12:35 +0000 (01:12 -0600)]
OMAP3 clock: DPLL{1,2}_FCLK clksel can divide by 4
OMAP34xx ES2 TRM Delta G to H states that the divider for DPLL1_FCLK and
DPLL2_FCLK can divide by 4 in addition to dividing by 1 and 2. Encode this
into the OMAP3 clock framework.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Tue, 24 Jun 2008 07:11:21 +0000 (01:11 -0600)]
OMAP3 clock: fix DPLL jitter correction and rate programming
Fix DPLL jitter correction programming. Previously,
omap3_noncore_dpll_program() stored the FREQSEL jitter correction
parameter to the wrong register. This caused jitter correction to be set
incorrectly and also caused the DPLL divider to be programmed incorrectly.
Also, fix DPLL divider programming. An off-by-one error existed in
omap3_noncore_dpll_program(), causing DPLLs to be programmed with a higher
divider than intended.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 07:09:21 +0000 (01:09 -0600)]
OMAP2 clock: check register address in omap2_clk_wait_ready()
The test in omap2_clk_wait_ready() for DSS or CAM clocks didn't
verify that the PRCM {F,I}CLKEN1 register was in the CORE powerdomain.
Add this check in.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 07:09:15 +0000 (01:09 -0600)]
OMAP3 clock: OMAP3430ES2+ has SSI target idlest bit
On OMAP3430ES2+, SSI has both an initiator standby CM_IDLEST bit, and a
target idle CM_IDLEST bit. This is a departure from previous silicon,
which only had an initiator standby bit.
This means that omap2_clk_wait_ready() needs to wait for the SSI
module to indicate readiness after both SSI interface and functional
clocks are enabled.
Thanks to Igor Stoppa <igor.stoppa@nokia.com>, Richard Woodruff
<r-woodruff2@ti.com>, and Jouni Högander <jouni.hogander@nokia.com> for
help with this portion of the patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 07:09:13 +0000 (01:09 -0600)]
OMAP3 clock: fix omap2_clk_wait_ready() for OMAP3430ES2+ DSS
On OMAP3430ES2, DSS has both an initiator standby CM_IDLEST bit, and a
target idle CM_IDLEST bit. This is a departure from previous silicon,
which only had an initiator standby bit.
This means we need to test the target idle bit after enabling
dss1_alwon_fclk. Previous clock code has done the wrong thing since ES2
came out: it's either tested the wrong bit, causing
Clock dss1_alwon_fck failed to enable in 100000 tries
messages, or not tested anything at all, causing crashes during DISPC
initialization with:
Unhandled fault: external abort on non-linefetch (0x1028)
This patch modifies omap2_clk_wait_ready() to wait for the DSS to become
accessible after dss1_alwon_fclk, dss_l3_iclk, and dss_l4_iclk are enabled.
Thanks to Anand Gadiyar <gadiyar@ti.com> for identifying one of the
problem patches, Koen Kooi <k.kooi@student.utwente.nl> for testing a
previous version of this patch, and Dirk Behme
<dirk.behme@googlemail.com> for review of a previous version.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 00:09:41 +0000 (18:09 -0600)]
OMAP3 PM: enable hardware SAR for USBHOST, USBTLL modules
Enable hardware save-and-restore for the CORE and USBHOST powerdomains
during PM layer initialization. On OMAP3, this only affects the
USBTLL and USBHOST modules.
There is probably a sleep and wakeup latency penalty with these
enabled. No one seems to have quantified it yet. If the added
latency is measurable, an alternate approach would be to only enable
hardware save-and-restore if there are USB devices attached.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 00:09:40 +0000 (18:09 -0600)]
OMAP3 pwrdm: add CORE SAR handling (for USBTLL module)
34xx TRM Delta G->H notes that the CORE powerdomain has a hardware
save-and-restore (SAR) control bit for the USBTLL module, similar to
the USBHOST powerdomain SAR bit. Split the existing core_34xx struct
powerdomain into two structs, one for ES1 and one for ES2, and add the
PWRDM_HAS_HDWR_SAR flag to the ES2 powerdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 00:09:39 +0000 (18:09 -0600)]
OMAP3: move USBHOST SAR handling from clock framework to powerdomain layer
Remove usbhost_sar_fclk from the OMAP3 clock framework. The bit that
the clock was tweaking doesn't actually enable or disable a clock; it
controls whether the hardware will save and restore USBHOST state
when the powerdomain changes state. (That happens to coincidentally
enable a clock for the duration of the operation, hence the earlier
confusion.)
In place of the clock, mark the USBHOST powerdomain as supporting
hardware save-and-restore functionality.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 26 Jun 2008 00:09:37 +0000 (18:09 -0600)]
OMAP3 pwrdm: add hardware save-and-restore (SAR) support
OMAP3430ES2+ introduces a new feature: optional powerdomain context
hardware save-and-restore (SAR). Currently, this feature only applies
to USBHOST and USBTLL module context when the USBHOST or CORE
powerdomains enter a low-power sleep state[1]. This feature avoids
re-enumeration of USB devices when the powerdomains return from idle,
which is potentially time-consuming.
This patch adds support for enabling and disabling hardware
save-and-restore to the powerdomain code. Three new functions are
added, pwrdm_enable_hdwr_sar(), pwrdm_disable_hdwr_sar(), and
pwrdm_can_hdwr_sar(). A new struct powerdomain "flags" field is
added, with a PWRDM_HAS_HDWR_SAR flag to indicate powerdomains with
SAR support.
Thanks to Jouni Högander <jouni.hogander@nokia.com> for reviewing an
earlier version of these patches, and Richard Woodruff <r-woodruff2@ti.com>
for clarifying the purpose of these bits.
1. For the USBHOST controller module, context loss occurs when the
USBHOST powerdomain enters off-idle. For USBTLL, context loss
occurs either if CORE enters off-idle, or if the CORE logic is
configured to turn off when CORE enters retention-idle (OSWR).
34xx ES2 TRM 4.8.6.1.1, 4.8.6.1.2
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kalle Jokiniemi [Tue, 24 Jun 2008 06:43:29 +0000 (09:43 +0300)]
ARM: OMAP: SmartReflex driver: enable in omap_3430sdp_defconfig
This patch enables the SmartReflex driver in omap_3430sdp_defconfig. Also removes
obsolete options and adds new previously undefined options as "not set".
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Wed, 25 Jun 2008 01:12:33 +0000 (18:12 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
[IA64] Handle count==0 in sn2_ptc_proc_write()
[IA64] Fix boot failure on ia64/sn2
Linus Torvalds [Wed, 25 Jun 2008 01:09:06 +0000 (18:09 -0700)]
Merge branch 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Remove now unused structs from kvm_para.h
x86: KVM guest: Use the paravirt clocksource structs and functions
KVM: Make kvm host use the paravirt clocksource structs
x86: Make xen use the paravirt clocksource structs and functions
x86: Add structs and functions for paravirt clocksource
KVM: VMX: Fix host msr corruption with preemption enabled
KVM: ioapic: fix lost interrupt when changing a device's irq
KVM: MMU: Fix oops on guest userspace access to guest pagetable
KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
KVM: MMU: Fix rmap_write_protect() hugepage iteration bug
KVM: close timer injection race window in __vcpu_run
KVM: Fix race between timer migration and vcpu migration
Jie Luo [Tue, 24 Jun 2008 17:38:31 +0000 (10:38 -0700)]
enable bus mastering on i915 at resume time
On 9xx chips, bus mastering needs to be enabled at resume time for much of the
chip to function. With this patch, vblank interrupts will work as expected
on resume, along with other chip functions. Fixes kernel bugzilla #10844.
Signed-off-by: Jie Luo <clotho67@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gerd Hoffmann [Tue, 3 Jun 2008 14:17:32 +0000 (16:17 +0200)]
x86: KVM guest: Use the paravirt clocksource structs and functions
This patch updates the kvm host code to use the pvclock structs
and functions, thereby making it compatible with Xen.
The patch also fixes an initialization bug: on SMP systems the
per-cpu has two different locations early at boot and after CPU
bringup. kvmclock must take that in account when registering the
physical address within the host.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Gerd Hoffmann [Tue, 3 Jun 2008 14:17:29 +0000 (16:17 +0200)]
x86: Add structs and functions for paravirt clocksource
This patch adds structs for the paravirt clocksource ABI
used by both xen and kvm (pvclock-abi.h).
It also adds some helper functions to read system time and
wall clock time from a paravirtual clocksource (pvclock.[ch]).
They are based on the xen code. They are enabled using
CONFIG_PARAVIRT_CLOCK.
Subsequent patches of this series will put the code in use.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the computation for zero_metapath_length(), which it
renames to metapath_branch_start(). When you are extending the metadata
tree, The indirect blocks that point to the new data block must either
diverge from the existing tree either at the inode, or at the first
indirect block. They can diverge at the first indirect block because the
inode has room for 483 pointers while the indirect blocks have room for
509 pointers, so when the tree is grown, there is some free space in the
first indirect block. What metapath_branch_start() now computes is the
height where the first indirect block for the new data block is located.
It can either be 1 (if the indirect block diverges from the inode) or 2
(if it diverges from the first indirect block).
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Julia Lawall [Tue, 24 Jun 2008 08:22:05 +0000 (10:22 +0200)]
[IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
As noted by Akinobu Mita alloc_bootmem and related functions never return
NULL and always return a zeroed region of memory. Thus a NULL test or
memset after calls to these functions is unnecessary.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Tony Luck <tony.luck@intel.com>
Cliff Wickman [Tue, 24 Jun 2008 17:20:06 +0000 (10:20 -0700)]
[IA64] Handle count==0 in sn2_ptc_proc_write()
The fix applied in e0c6d97c65e0784aade7e97b9411f245a6c543e7
"security hole in sn2_ptc_proc_write" didn't take into account
the case where count==0 (which results in a buffer underrun
when adding the trailing '\0'). Thanks to Andi Kleen for
pointing this out.
Signed-off-by: Cliff Wickman <cpw@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used. xen-unstable has now officially dropped
non-PAE support. Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Avi Kivity [Tue, 24 Jun 2008 08:48:49 +0000 (11:48 +0300)]
KVM: VMX: Fix host msr corruption with preemption enabled
Switching msrs can occur either synchronously as a result of calls to
the msr management functions (usually in response to the guest touching
virtualized msrs), or asynchronously when preempting a kvm thread that has
guest state loaded. If we're unlucky enough to have the two at the same
time, host msrs are corrupted and the machine goes kaput on the next syscall.
Most easily triggered by Windows Server 2008, as it does a lot of msr
switching during bootup.
Avi Kivity [Tue, 17 Jun 2008 22:36:36 +0000 (15:36 -0700)]
KVM: ioapic: fix lost interrupt when changing a device's irq
The ioapic acknowledge path translates interrupt vectors to irqs. It
currently uses a first match algorithm, stopping when it finds the first
redirection table entry containing the vector. That fails however if the
guest changes the irq to a different line, leaving the old redirection table
entry in place (though masked). Result is interrupts not making it to the
guest.
Fix by always scanning the entire redirection table.
Avi Kivity [Thu, 12 Jun 2008 13:54:41 +0000 (16:54 +0300)]
KVM: MMU: Fix oops on guest userspace access to guest pagetable
KVM has a heuristic to unshadow guest pagetables when userspace accesses
them, on the assumption that most guests do not allow userspace to access
pagetables directly. Unfortunately, in addition to unshadowing the pagetables,
it also oopses.
This never triggers on ordinary guests since sane OSes will clear the
pagetables before assigning them to userspace, which will trigger the flood
heuristic, unshadowing the pagetables before the first userspace access. One
particular guest, though (Xenner) will run the kernel in userspace, triggering
the oops. Since the heuristic is incorrect in this case, we can simply
remove it.
Marcelo Tosatti [Wed, 11 Jun 2008 23:32:40 +0000 (20:32 -0300)]
KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
kvm_mmu_pte_write() does not handle 32-bit non-PAE large page backed
guests properly. It will instantiate two 2MB sptes pointing to the same
physical 2MB page when a guest large pte update is trapped.
Instead of duplicating code to handle this, disallow directory level
updates to happen through kvm_mmu_pte_write(), so the two 2MB sptes
emulating one guest 4MB pte can be correctly created by the page fault
handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
rmap_next() does not work correctly after rmap_remove(), as it expects
the rmap chains not to change during iteration. Fix (for now) by restarting
iteration from the beginning.
Marcelo Tosatti [Fri, 6 Jun 2008 19:37:36 +0000 (16:37 -0300)]
KVM: close timer injection race window in __vcpu_run
If a timer fires after kvm_inject_pending_timer_irqs() but before
local_irq_disable() the code will enter guest mode and only inject such
timer interrupt the next time an unrelated event causes an exit.
It would be simpler if the timer->pending irq conversion could be done
with IRQ's disabled, so that the above problem cannot happen.
For now introduce a new vcpu requests bit to cancel guest entry.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Marcelo Tosatti [Fri, 6 Jun 2008 19:37:35 +0000 (16:37 -0300)]
KVM: Fix race between timer migration and vcpu migration
A guest vcpu instance can be scheduled to a different physical CPU
between the test for KVM_REQ_MIGRATE_TIMER and local_irq_disable().
If that happens, the timer will only be migrated to the current pCPU on
the next exit, meaning that guest LAPIC timer event can be delayed until
a host interrupt is triggered.
Fix it by cancelling guest entry if any vcpu request is pending. This
has the side effect of nicely consolidating vcpu->requests checks.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Linus Torvalds [Mon, 23 Jun 2008 23:25:11 +0000 (16:25 -0700)]
Merge branch 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: nfs_updatepage(): don't mark page as dirty if an error occurred
NFS: Fix filehandle size comparisons in the mount code
NFS: Reduce the NFS mount code stack usage.
Linus Torvalds [Mon, 23 Jun 2008 19:48:50 +0000 (12:48 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: refactor wait_for_completion_timeout()
sched: fix wait_for_completion_timeout() spurious failure under heavy load
sched: rt: dont stop the period timer when there are tasks wanting to run
Linus Torvalds [Mon, 23 Jun 2008 19:48:17 +0000 (12:48 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: don't drop NX bit
xen: mask unwanted pte bits in __supported_pte_mask
xen: Use wmb instead of rmb in xen_evtchn_do_upcall().
x86: fix NULL pointer deref in __switch_to
Nick Piggin [Mon, 23 Jun 2008 12:30:30 +0000 (14:30 +0200)]
mm: fix race in COW logic
There is a race in the COW logic. It contains a shortcut to avoid the
COW and reuse the page if we have the sole reference on the page,
however it is possible to have two racing do_wp_page()ers with one
causing the other to mistakenly believe it is safe to take the shortcut
when it is not. This could lead to data corruption.
Process 1 and process2 each have a wp pte of the same anon page (ie.
one forked the other). The page's mapcount is 2. Then they both
attempt to write to it around the same time...
write private key into page
read from page
ptep_clear_flush()
set_pte_at(pte of new_page)
Fix this by moving the page_remove_rmap of the old page after the pte
clear and flush. Potentially the entire branch could be moved down
here, but in order to stay consistent, I won't (should probably move all
the *_mm_counter stuff with one patch).
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Hugh Dickins <hugh@veritas.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"This broke vmware 6.0.4.
Jun 22 14:53:03.845: vmx| NOT_IMPLEMENTED
/build/mts/release/bora-93057/bora/vmx/main/vmmonPosix.c:774"
and the reason seems to be that there's an old bug in how we handle do
FOLL_ANON on VM_SHARED areas in get_user_pages(), but since it only
triggered if the whole page table was missing, nobody had apparently hit
it before.
The recent changes to 'follow_page()' made the FOLL_ANON logic trigger
not just for whole missing page tables, but for individual pages as
well, and exposed this problem.
This fixes it by making the test for when FOLL_ANON is used more
careful, and also makes the code easier to read and understand by moving
the logic to a separate inline function.
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eli Cohen [Mon, 23 Jun 2008 16:29:58 +0000 (09:29 -0700)]
IB/mthca: Clear ICM pages before handing to FW
Current memfree FW has a bug which in some cases, assumes that ICM
pages passed to it are cleared. This patch uses __GFP_ZERO to
allocate all ICM pages passed to the FW. Once firmware with a fix is
released, we can make the workaround conditional on firmware version.
This fixes the bug reported by Arthur Kepner <akepner@sgi.com> here:
http://lists.openfabrics.org/pipermail/general/2008-May/050026.html
Cc: <stable@kernel.org> Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Rewritten to be a one-liner using __GFP_ZERO instead of vmap()ing
ICM memory and memset()ing it to 0. - Roland ]
Thomas Gleixner [Mon, 23 Jun 2008 09:21:58 +0000 (11:21 +0200)]
futexes: fix fault handling in futex_lock_pi
This patch addresses a very sporadic pi-futex related failure in
highly threaded java apps on large SMP systems.
David Holmes reported that the pi_state consistency check in
lookup_pi_state triggered with his test application. This means that
the kernel internal pi_state and the user space futex variable are out
of sync. First we assumed that this is a user space data corruption,
but deeper investigation revieled that the problem happend because the
pi-futex code is not handling a fault in the futex_lock_pi path when
the user space variable needs to be fixed up.
The fault happens when a fork mapped the anon memory which contains
the futex readonly for COW or the page got swapped out exactly between
the unlock of the futex and the return of either the new futex owner
or the task which was the expected owner but failed to acquire the
kernel internal rtmutex. The current futex_lock_pi() code drops out
with an inconsistent in case it faults and returns -EFAULT to user
space. User space has no way to fixup that state.
When we wrote this code we thought that we could not drop the hash
bucket lock at this point to handle the fault.
After analysing the code again it turned out to be wrong because there
are only two tasks involved which might modify the pi_state and the
user space variable:
- the task which acquired the rtmutex
- the pending owner of the pi_state which did not get the rtmutex
Both tasks drop into the fixup_pi_state() function before returning to
user space. The first task which acquired the hash bucket lock faults
in the fixup of the user space variable, drops the spinlock and calls
futex_handle_fault() to fault in the page. Now the second task could
acquire the hash bucket lock and tries to fixup the user space
variable as well. It either faults as well or it succeeds because the
first task already faulted the page in.
One caveat is to avoid a double fixup. After returning from the fault
handling we reacquire the hash bucket lock and check whether the
pi_state owner has been modified already.
Reported-by: David Holmes <david.holmes@sun.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Holmes <david.holmes@sun.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
kernel/futex.c | 93 ++++++++++++++++++++++++++++++++++++++++++++-------------
1 file changed, 73 insertions(+), 20 deletions(-)
arun c [Wed, 11 Jun 2008 10:36:24 +0000 (16:06 +0530)]
This patch completes the name change from 2430osk to OMAP2EVM
From 11262ea96e0fa73dd3470362b571a33b792bfb09 Mon Sep 17 00:00:00 2001
From: arun <arunedarath@mistralsolutions.com>
Date: Wed, 11 Jun 2008 15:46:10 +0530
Subject: [PATCH] This patch completes the name change from 2430osk to OMAP2EVM
Also
a) Changed old style i2c registration
b) Changed the Maintainer
Signed-off-by: arun <arunedarath@mistralsolutions.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
arun c [Wed, 11 Jun 2008 12:11:47 +0000 (17:41 +0530)]
Renaming files to reflect name change from 2430OSK to OMAP2EVM
From c379ad7c092bd0230d6c24652a86abb2d8184d64 Mon Sep 17 00:00:00 2001
From: arun <arunedarath@mistralsolutions.com>
Date: Wed, 11 Jun 2008 14:43:34 +0530
Subject: [PATCH] Renaming files to reflect name change from 2430OSK to OMAP2EVM
Kalle Jokiniemi [Tue, 17 Jun 2008 07:23:06 +0000 (10:23 +0300)]
ARM: OMAP: SmartReflex driver integration
This patch integrates TI's SmartReflex driver into linux-omap. SmartReflex is
a module that adjusts OMAP3 VDD1 and VDD2 operating voltages around the
nominal values of current operating point depending on silicon
characteristics and operating conditions.
The patch adds Kconfig options "SmartReflex support" and a sub-option
"SmartReflex testing support" under "System type"->"TI OMAP implementations"
menu. The testing support can be used to test SmartReflex functionality, if
the E-fuse values have not been set for the device. It however uses software
hard coded sensor parameters, which may not work on all devices. Beware.
The driver creates two sysfs entries into /sys/power/ named
"sr_vdd1_autocomp" and "sr_vdd2_autocomp" which can be used to activate
voltage autocompensation feature of SmartReflex modules 1 and 2.
Use the following commands to enable autocompensation:
Kalle Jokiniemi [Thu, 19 Jun 2008 10:42:26 +0000 (13:42 +0300)]
ARM: OMAP: SmartReflex driver: added required register and bit definitions.
Added new register and bit definitions to enable Smartreflex driver
integration. Also PRM_VC_SMPS_SA bit definitions' naming was changed to match
the naming of other similar bit definitions.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
The fix prevents kernel crash caused by twl4030 power button malfunction.
If i2c connection is broken the twl4030 power button driver is unregistered.
The function input_free_device has to be called only when
input_register_device failed. Otherwise input_unregister_device is used.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Eduardo Valentin [Tue, 10 Jun 2008 17:42:11 +0000 (13:42 -0400)]
tea5761 tuner: fix registers utilization
Fix registers utilization.
tnctrl register was supposed to be used but it was
right shifted. frqset also was being configured using
incorrect equation.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Sun, 22 Jun 2008 19:23:15 +0000 (12:23 -0700)]
Fix performance regression on lmbench select benchmark
Christian Borntraeger reported that reinstating cond_resched() with
CONFIG_PREEMPT caused a performance regression on lmbench:
For example select file 500:
23 microseconds
32 microseconds
and that's really because we totally unnecessarily do the cond_resched()
in the innermost loop of select(), which is just silly.
This moves it out from the innermost loop (which only ever loops ove the
bits in a single "unsigned long" anyway), which makes the performance
regression go away.
Reported-and-tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The zonelist patches caused the loop that checks for available
objects in permitted zones to not terminate immediately. One object
per zone per allocation may be allocated and then abandoned.
Break the loop when we have successfully allocated one object.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: Don't receive new packets in a dead network namespace.
sctp: Make sure N * sizeof(union sctp_addr) does not overflow.
pppoe: warning fix
ipv6: Drop packets for loopback address from outside of the box.
ipv6: Remove options header when setsockopt's optlen is 0
mac80211: detect driver tx bugs
projects / linux-2.6-omap-h63xx.git / log