Alan Stern [Wed, 12 Nov 2008 22:02:57 +0000 (17:02 -0500)]
USB: EHCI: fix divide-by-zero bug
This patch (as1164) fixes a bug in the EHCI scheduler. The interval
value it uses is already in linear format, not logarithmically coded.
The existing code can sometimes crash the system by trying to divide
by zero.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Cc: Stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 12 Nov 2008 22:04:53 +0000 (17:04 -0500)]
USB: EHCI: fix handling of dead controllers
This patch (as1165) makes a few small changes in the logic used by
ehci-hcd when it encounters a controller error:
Instead of printing out the masked status, it prints the
original status as read directly from the hardware.
It doesn't check for the STS_HALT status bit before taking
action. The mere fact that the STS_FATAL bit is set means
that something bad has happened and the controller needs to
be reset. With the old code this test could never succeed
because the STS_HALT bit was masked out from the status.
I anticipate that this will prevent the occasional "irq X: nobody cared"
problem people encounter when their EHCI controllers die.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is because usb_reset_device now unbinds, and that calls disconnect,
which in case of ub waits until the reset completes... which deadlocks.
Worse, this deadlocks keventd and this takes whole box down.
I'm going to fix this properly later, but let's unbreak the driver
quickly for non-composite devices at least.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reason, is that ret is initialized with ENODEV instead of 0 _or_
the kmem cache is not freed in error case with no bus binding.
The difference between OF+PCI and OF only is
| 15148 804 32 15984 3e70 isp1760-of-pci.o
| 13748 676 8 14432 3860 isp1760-of.o
about 1.5 KiB.
Until there is a checkbox where the user *must* select atleast one item,
and may select multiple entries I don't make it selectable anymore.
Having a driver which can't be used under any circumstances is broken
anyway and I've seen distros shipping it that way.
Reported-by: Roland Kletzing <devzero@web.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>a Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Paul Bolle [Thu, 30 Oct 2008 15:42:43 +0000 (08:42 -0700)]
USB: storage: adjust comment in Kconfig
Since commit 65934a9 ("Make USB storage depend on SCSI rather than selecting
it [try #6]") the comment at the top of drivers/usb/storage/Kconfig is
incorrect. Adjust it to the current situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Geoff Levand [Fri, 31 Oct 2008 20:52:54 +0000 (13:52 -0700)]
USB: Fix PS3 USB shutdown problems
Add ehci_shutdown() or ohci_shutdown() calls to the USB
PS3 bus glue. ehci_shutdown() and ohci_shutdown() do some
controller specific cleanups not done by usb_remove_hcd().
Fixes errors on shutdown or reboot similar to these:
ps3-ehci-driver sb_07: HC died; cleaning up
irq 51: nobody cared (try booting with the "irqpoll" option)
Brandon Philips [Thu, 6 Nov 2008 19:19:11 +0000 (11:19 -0800)]
USB: cdc-acm.c: fix recursive lock in acm_start_wb error path
Fixes an obvious bug in cdc-acm by avoiding a recursive lock on
acm_start_wb()'s error path. Should apply towards 2.6.27 stable and
2.6.28.
=============================================
[ INFO: possible recursive locking detected ]
2.6.27-2-pae #109
---------------------------------------------
python/31449 is trying to acquire lock:
(&acm->write_lock){++..}, at: [<f89a0348>] acm_start_wb+0x5c/0x7b [cdc_acm]
but task is already holding lock:
(&acm->write_lock){++..}, at: [<f89a04fb>] acm_tty_write+0xe1/0x167 [cdc_acm]
other info that might help us debug this:
2 locks held by python/31449:
#0: (&tty->atomic_write_lock){--..}, at: [<c0260fae>] tty_write_lock+0x14/0x3b
#1: (&acm->write_lock){++..}, at: [<f89a04fb>] acm_tty_write+0xe1/0x167 [cdc_acm]
usb: musb: fix BULK request on different available endpoints
Fixes co-working issue of usb serial device with usb/net devices while
oter endpoints are free and can be used.This patch implements the policy
that if endpoint resources are available then different BULK request goes
to different endpoint otherwise they are multiplexed to one reserved
endpoint as currently done.
Switch statement case is reordered in musb_giveback() to take care of
bulk request both in multiplex scenario and otherwise.
NAK limit scheme has to be added for multiplexed BULK request scenario
to avoid endpoint starvation due to usb/net devices.
Alan Stern [Wed, 29 Oct 2008 19:16:58 +0000 (15:16 -0400)]
USB: don't register endpoints for interfaces that are going away
This patch (as1155) fixes a bug in usbcore. When interfaces are
deleted, either because the device was disconnected or because of a
configuration change, the extra attribute files and child endpoint
devices may get left behind. This is because the core removes them
before calling device_del(). But during device_del(), after the
driver is unbound the core will reinstall altsetting 0 and recreate
those extra attributes and children.
The patch prevents this by adding a flag to record when the interface
is in the midst of being unregistered. When the flag is set, the
attribute files and child devices will not be created.
Linus Torvalds [Thu, 13 Nov 2008 19:30:46 +0000 (11:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slab: document SLAB_DESTROY_BY_RCU
Kconfig: SLUB is the default slab allocator
An extraneous 'else' slipped into a code fragment being moved from
release_lockspace() to dlm_release_lockspace(). The result of the
unwanted 'else' is that dlm threads and structures are not stopped
and cleaned up when the final dlm lockspace is removed. Trying to
create a new lockspace again afterward will fail with
"kmem_cache_create: duplicate cache dlm_conn" because the cache
was not previously destroyed.
Signed-off-by: David Teigland <teigland@redhat.com>
Peter Zijlstra [Thu, 13 Nov 2008 18:40:12 +0000 (20:40 +0200)]
slab: document SLAB_DESTROY_BY_RCU
Explain this SLAB_DESTROY_BY_RCU thing...
[hugh@veritas.com: add a pointer to comment in mm/slab.c] Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Jens Axboe <jens.axboe@oracle.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Simon Arlott [Wed, 5 Nov 2008 22:18:19 +0000 (22:18 +0000)]
Kconfig: SLUB is the default slab allocator
In 2007, a0acd820807680d2ccc4ef3448387fcdbf152c73 changed the default
slab allocator to SLUB, but the SLAB help text still says SLAB is the
default. This change fixes that.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Linus Torvalds [Thu, 13 Nov 2008 01:22:44 +0000 (17:22 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix init_idle()'s use of sched_clock()
sched: fix stale value in average load per task
Rodolfo Giometti [Wed, 12 Nov 2008 21:27:12 +0000 (13:27 -0800)]
Add c2 port support
C2port implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices.
Currently this code supports only flash programming through sysfs
interface but extensions shoud be easy to add.
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols. These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).
This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Jackson [Wed, 12 Nov 2008 21:27:07 +0000 (13:27 -0800)]
rtc: add Dallas DS1390/93/94 RTC chips
Add support for the Dallas DS1390/93/94 SPI RTC chip.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Wed, 12 Nov 2008 21:27:04 +0000 (13:27 -0800)]
rtc: rtc-wm8350: add support for WM8350 RTC
This adds support for the RTC provided by the Wolfson Microelectronics
WM8350.
This driver was originally written by Graeme Gregory and Liam Girdwood,
though it has been modified since then to update it to current mainline
coding standards and for API completeness.
[akpm@linux-foundation.org: s/schedule_timeout_interruptible/schedule_timeout_uninterruptible/ to prevent bogus timeout when signal_pending()] Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: Liam Girdwood <linux@wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:27:04 +0000 (13:27 -0800)]
ics932s401: new clock generator chip driver
The ics932s401 is a clock generator chip. This driver allows users to
read the current clock outputs.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:27:03 +0000 (13:27 -0800)]
adt7462: new hwmon driver
New driver to play with. As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors. This driver has been tested on an IntelliStation Z30.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Machek [Wed, 12 Nov 2008 21:27:02 +0000 (13:27 -0800)]
LIS3LV02Dx Accelerometer driver
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard"). It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.
This driver was first written by Yan Burman. Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now). Pavel Machek removed few more features and switched locking from
semaphore to mutex.
Several people have contributed to the database of the axes.
[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API] Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Yan Burman <burman.yan@gmail.com> Signed-off-by: Pavel Machek <pavel@suse.cz> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atmel_spi: work-around required for new HW bug in AT91SAM9263 Rev.B SPI controller
We're working with an AT91SAM9263 Rev B in our design and I experienced
some inconsistency in spi-based touchscreen usage between our board and
the Atmel evaluation kit we have that runs on a Rev A chip.
The data was apparently delayed by 1 byte and got ridiculous data out of
the touchscreen driver, very strange. As everything looked normal in
the spi, touchscreen and dma logs, I contacted the Atmel support and
they triggered me on a new HW bug that appeared in the Rev B SPI
controller.
The problem is that the SPI controller on the Rev B needs that the
software reset is performed two times so that it's performed correctly.
Applying the patch below solves the issue on my Rev B board. I've tested
it as well on my Rev A evaluation kit and it has apparently no unwanted
side effect, things continue to work as expected.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:26:59 +0000 (13:26 -0800)]
lm85: support adt7468 chips
The adt7468 is a follow-on to the adt7463, so plumb in adt7468 support
along the same code paths.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:26:58 +0000 (13:26 -0800)]
adt7473: check inputs from sysfs writes
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:26:57 +0000 (13:26 -0800)]
adt7470: check input range when sysfs files are written
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 12 Nov 2008 21:26:55 +0000 (13:26 -0800)]
remove ratelimt()
It mistakenly assumes that a static local in an inlined function is a
kernel-wide singleton. It also has no callers, so let's remove it.
Cc: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the last refactoring of shrink_submounts a variable was not completely
renamed. So finish the renaming of mnt to m now.
Without this if you attempt to mount an nfs mount that has both automatic
nfs sub mounts on it, and has normal mounts on it. The unmount will
succeed when it should not.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@ZenIV.linux.org.uk Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Wed, 12 Nov 2008 21:26:53 +0000 (13:26 -0800)]
mm: remove lru_add_drain_all() from the munlock path
lockdep warns about following message at boot time on one of my test
machine. Then, schedule_on_each_cpu() sholdn't be called when the task
have mmap_sem.
Actually, lru_add_drain_all() exist to prevent the unevictalble pages
stay on reclaimable lru list. but currenct unevictable code can rescue
unevictable pages although it stay on reclaimable list.
So removing is better.
In addition, this patch add lru_add_drain_all() to sys_mlock() and
sys_mlockall(). it isn't must. but it reduce the failure of moving to
unevictable list. its failure can rescue in vmscan later. but reducing
is better.
Note, if above rescuing happend, the Mlocked and the Unevictable field
mismatching happend in /proc/meminfo. but it doesn't cause any real
trouble.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.28-rc2-mm1 #2
-------------------------------------------------------
lvm/1103 is trying to acquire lock:
(&cpu_hotplug.lock){--..}, at: [<c0130789>] get_online_cpus+0x29/0x50
but task is already holding lock:
(&mm->mmap_sem){----}, at: [<c01878ae>] sys_mlockall+0x4e/0xb0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Masami Hiramatsu [Wed, 12 Nov 2008 21:26:51 +0000 (13:26 -0800)]
kprobes: disable preempt for module_text_address() and kernel_text_address()
__register_kprobe() can be preempted after checking probing address but
before module_text_address() or try_module_get(), and in this interval
the module can be unloaded. In that case, try_module_get(probed_mod)
will access to invalid address, or kprobe will probe invalid address.
This patch uses preempt_disable() to protect it and uses
__module_text_address() and __kernel_text_address().
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Wed, 12 Nov 2008 21:26:50 +0000 (13:26 -0800)]
freezer_cg: disable writing freezer.state of root cgroup
With this change, control file 'freezer.state' doesn't exist in root
cgroup, making root cgroup unfreezable.
I think it's reasonable to disallow freeze tasks in the root cgroup. And
then we can avoid fork overhead when freezer subsystem is compiled but not
used.
Also make writing invalid value to freezer.state returns EINVAL rather
than EIO. This is more consistent with other cgroup subsystem.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Menage <menage@google.com> Cc: Cedric Le Goater <clg@fr.ibm.com> Cc: Paul Menage <menage@google.com> Cc: Matt Helsley <matthltc@us.ibm.com> Cc: "Serge E. Hallyn" <serue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Wed, 12 Nov 2008 21:26:49 +0000 (13:26 -0800)]
freezer_cg: remove task_lock from freezer_fork()
In theory the task can be moved to another cgroup and the freezer will be
freed right after task_lock is dropped, so the lock results in zero
protection.
But in the case of freezer_fork() no lock is needed, since the task is not
in tasklist yet so it won't be moved to another cgroup, so task->cgroups
won't be changed or invalidated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Matt Helsley <matthltc@us.ibm.com> Cc: Cedric Le Goater <clg@fr.ibm.com> Cc: "Serge E. Hallyn" <serue@us.ibm.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Wed, 12 Nov 2008 21:25:37 +0000 (13:25 -0800)]
cpusets: update mems allowed in page allocator
If all allowable memory is unreclaimable, it is possible to loop forever
in the page allocator for ~__GFP_NORETRY allocations.
During this time, it is also possible for a task's cpuset to expand its
set of allowable nodes so that it now includes free memory. The cached
copy of this set, current->mems_allowed, is stale, however, since there
has not been a subsequent call to cpuset_update_task_memory_state().
The cached copy of the set of allowable nodes is now updated in the page
allocator's slow path so the additional memory is available to
get_page_from_freelist().
[akpm@linux-foundation.org: add comment] Signed-off-by: David Rientjes <rientjes@google.com> Cc: Paul Menage <menage@google.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:25:36 +0000 (13:25 -0800)]
i5000-edac: hold reference to mci kobject
It turns out that edac_mc_del_mc will kobject_put the last kref on the
mci object.
If the timing is just right, that means that the mci object is freed
before before i5000_remove_one has a chance to free the resources
associated with it, causing a null pointer exceptions when unloading the
driver. Insert a kobject_{get,put} pair so that this doesn't happen.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Cc: Doug Thompson <norsk5@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Wed, 12 Nov 2008 21:25:00 +0000 (13:25 -0800)]
Fix platform drivers that crash on suspend/resume
It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.
This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash. Make this assumption hold true for these
three drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Greg KH <greg@kroah.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Litke [Wed, 12 Nov 2008 21:24:56 +0000 (13:24 -0800)]
hugetlb: make unmap_ref_private multi-size-aware
Oops. Part of the hugetlb private reservation code was not fully
converted to use hstates.
When a huge page must be unmapped from VMAs due to a failed COW,
HPAGE_SIZE is used in the call to unmap_hugepage_range() regardless of
the page size being used. This works if the VMA is using the default
huge page size. Otherwise we might unmap too much, too little, or
trigger a BUG_ON. Rare but serious -- fix it.
Signed-off-by: Adam Litke <agl@us.ibm.com> Cc: Jon Tollefson <kniht@linux.vnet.ibm.com> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: fix poll_controller to pass proper structures and check all rx queues
niu: Fix readq implementation when architecture does not provide one.
hostap: pad the skb->cb usage in lieu of a proper fix
rtl8187 : support for Sitecom WL-168 0001 v4
mac80211: fix notify_mac function
rtl8187: Add Abocom USB ID
net: put_cmsg_compat + SO_TIMESTAMP[NS]: use same name for value as caller
tcp_htcp: last_cong bug fix
[netdrvr] smc911x: fix for driver resume (and compilation warning)
RDMA/cxgb3: deadlock in iw_cxgb3 can cause hang when configuring interface.
cxgb3 - Limit multiqueue setting to msi-x
cxgb3 - eeprom read fixes
myri10ge: fix stop/go ordering even more
David S. Miller [Wed, 12 Nov 2008 22:32:54 +0000 (14:32 -0800)]
niu: Fix readq implementation when architecture does not provide one.
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 12 Nov 2008 21:54:22 +0000 (16:54 -0500)]
hostap: pad the skb->cb usage in lieu of a proper fix
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 11 Nov 2008 10:28:04 +0000 (11:28 +0100)]
mac80211: fix notify_mac function
The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivan Kuten [Tue, 11 Nov 2008 01:39:25 +0000 (19:39 -0600)]
rtl8187: Add Abocom USB ID
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Wed, 12 Nov 2008 19:48:54 +0000 (11:48 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: struct device - replace bus_id with dev_name(), dev_set_name()
iop-adma: use iop_paranoia() for debug BUG_ONs
iop-adma: add a dummy read to flush next descriptor update
Ingo Molnar [Wed, 12 Nov 2008 19:05:50 +0000 (20:05 +0100)]
sched: fix init_idle()'s use of sched_clock()
Maciej Rutecki reported:
> I have this bug during suspend to disk:
>
> [ 188.592151] Enabling non-boot CPUs ...
> [ 188.592151] SMP alternatives: switching to SMP code
> [ 188.666058] BUG: using smp_processor_id() in preemptible
> [00000000]
> code: suspend_to_disk/2934
> [ 188.666064] caller is native_sched_clock+0x2b/0x80
Linus Torvalds [Wed, 12 Nov 2008 18:56:31 +0000 (10:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix crash in path_rec_completion()
IPoIB: Fix hang in ipoib_flush_paths()
IPoIB: Don't enable NAPI when it's already enabled
RDMA/cxgb3: Fix deadlock in iw_cxgb3 (hang when configuring interface)
IB/ehca: Remove reference to special QP in case of port activation failure
IB/mlx4: Set umem field to NULL in mlx4_ib_alloc_fast_reg_mr()
mlx4_core: Fix unused variable warning
RDMA/nes: Mitigate compatibility issue regarding PCIe write credits
RDMA/nes: Fix CQ allocation scheme for multicast receive queue apps
RDMA/nes: Correct handling of PBL resources
RDMA/nes: Reindent mis-indented spinlocks
RDMA/cxgb3: Fix too-big reserved field zeroing in iwch_post_zb_read()
IB/ipath: Fix RDMA write with immediate copy of last packet
David Howells [Wed, 12 Nov 2008 15:35:45 +0000 (15:35 +0000)]
MN10300: Handle misaligned SP-based operands
Support misalignment handling for instructions that have kernel SP-based
address operands, including fixing those that include IMM8 or IMM16
displacements.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correctly handle misalignment in MOV instructions with postinc-with-immediate
addressing mode operands. In these, the immediate value is the increment to
be applied the address register, not the displacement to the address.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misalignment handling of operands with register postincrement addressing.
The flag to indicate that postincrement is required should not be interpreted
as an specification of a value to be added to the address.
Also add BUGs to catch unimplemented parameter markings in the opcodes table.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 12 Nov 2008 18:38:42 +0000 (10:38 -0800)]
Merge branch 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Fix pit memory leak if unable to allocate irq source id
KVM: ia64: fix vmm_spin_{un}lock for !CONFIG_SMP
KVM: VMX: Set IGMT bit in EPT entry
KVM: Require the PCI subsystem
x86: KVM guest: fix section mismatch warning in kvmclock.c
KVM: ia64: Use guest signal mask when blocking
KVM: MMU: increase per-vcpu rmap cache alloc size
Denys Vlasenko [Wed, 12 Nov 2008 00:24:41 +0000 (01:24 +0100)]
parisc: fix find_extend_vma() breakage
The STACK_GROWSUP case of stack expansion was missing a test for 'prev',
which got removed by commit cb8f488c33539f096580e202f5438a809195008f
("mmap.c: deinline a few functions") by mistake.
I found my original email in "sent" folder. The patch in that mail
does NOT remove !prev. That change had beed added by someone else.
Ok, I think we are not much interested in who did it, let's
fix it for good.
[ "It looks like this was caused by me fixing rejects. That was the
fancy include-lots-of-context-so-it-wont-apply patch." - akpm ]
Linus Torvalds [Wed, 12 Nov 2008 18:24:46 +0000 (10:24 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (47 commits)
ACPI: pci_link: remove acpi_irq_balance_set() interface
fujitsu-laptop: Add DMI callback for Lifebook S6420
ACPI: EC: Don't do transaction from GPE handler in poll mode.
ACPI: EC: lower interrupt storm treshold
ACPICA: Use spinlock for acpi_{en|dis}able_gpe
ACPI: EC: restart failed command
ACPI: EC: wait for last write gpe
ACPI: EC: make kernel messages more useful when GPE storm is detected
ACPI: EC: revert msleep patch
thinkpad_acpi: fingers off backlight if video.ko is serving this functionality
sony-laptop: fingers off backlight if video.ko is serving this functionality
msi-laptop: fingers off backlight if video.ko is serving this functionality
fujitsu-laptop: fingers off backlight if video.ko is serving this functionality
eeepc-laptop: fingers off backlight if video.ko is serving this functionality
compal: fingers off backlight if video.ko is serving this functionality
asus-acpi: fingers off backlight if video.ko is serving this functionality
Acer-WMI: fingers off backlight if video.ko is serving this functionality
ACPI video: if no ACPI backlight support, use vendor drivers
ACPI: video: Ignore devices that aren't present in hardware
Delete an unwanted return statement at evgpe.c
...
Yossi Etigin [Wed, 12 Nov 2008 18:24:39 +0000 (10:24 -0800)]
IPoIB: Fix crash in path_rec_completion()
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
projects / linux-2.6-omap-h63xx.git / log