* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
Merge branch 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: add hardware handshake support to atmel_serial
avr32: add RTS/CTS/CLK pin selection for the USARTs
Add RTC support for Merisc boards
avr32: at32ap700x: setup DMA for AC97C in the machine code
avr32: at32ap700x: setup DMA for ABDAC in the machine code
Add Merisc board support
avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
avr32: fix timing LCD parameters for EVKLCD10X boards
avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
avr32: configure MCI detect and write protect pins for EVKLCD10x boards
avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
avr32: add pin mask for 18-bit color on the LCD controller
avr32: fix 15-bit LCDC pin mask to use MSB lines
Merge branch 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
Merge branch 'bzip2-lzma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip
* 'bzip2-lzma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
bzip2/lzma: quiet Kconfig warning for INITRAMFS_COMPRESSION_NONE
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: use strstarts()
strstarts: helper function for !strncmp(str, prefix, strlen(prefix))
arm: allow usage of string functions in linux/string.h
module: don't use stop_machine on module load
module: create a request_module_nowait()
module: include other structures in module version check
module: remove the SHF_ALLOC flag on the __versions section.
module: clarify the force-loading taint message.
module: Export symbols needed for Ksplice
Ksplice: Add functions for walking kallsyms symbols
module: remove module_text_address()
module: __module_address
module: Make find_symbol return a struct kernel_symbol
kernel/module.c: fix an unused goto label
param: fix charp parameters set via sysfs
Fix trivial conflicts in kernel/extable.c manually.
Merge branch 'core/debugobjects' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/debugobjects' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: delay free of internal objects
debugobjects: replace static objects when slab cache becomes available
debug_objects: add boot-parameter toggle to turn object debugging off again
Merge branch 'printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
printk: correct the behavior of printk_timed_ratelimit()
vsprintf: unify the format decoding layer for its 3 users, cleanup
fix regression from "vsprintf: unify the format decoding layer for its 3 users"
vsprintf: fix bug in negative value printing
vsprintf: unify the format decoding layer for its 3 users
vsprintf: add binary printf
printk: introduce printk_once()
Fix trivial conflicts (printk_once vs log_buf_kexec_setup() added near
each other) in include/linux/kernel.h.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
atmel-mci: fix sdc_reg typo
tmio_mmc: add maintainer
mmc: Add OpenFirmware bindings for SDHCI driver
sdhci: Add quirk for forcing maximum block size to 2048 bytes
sdhci: Add quirk for controllers that need IRQ re-init after reset
sdhci: Add quirk for controllers that need small delays for PIO
sdhci: Add set_clock callback and a quirk for nonstandard clocks
sdhci: Add get_{max,timeout}_clock callbacks
sdhci: Add support for hosts reporting inverted write-protect state
sdhci: Add support for card-detection polling
sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
sdhci: Split card-detection IRQs management from sdhci_init()
sdhci: Add support for bus-specific IO memory accessors
mmc_spi: adjust for delayed data token response
omap_hsmmc: Wait for SDBP
omap_hsmmc: Fix MMC3 dma
omap_hsmmc: Disable SDBP at suspend
omap_hsmmc: Do not prefix slot name
omap_hsmmc: Allow cover switch to cause rescan
omap_hsmmc: Add 8-bit bus width mode support
...
Bjorn Helgaas [Mon, 30 Mar 2009 17:48:24 +0000 (17:48 +0000)]
ACPI: processor: use .notify method instead of installing handler directly
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> CC: Zhang Rui <rui.zhang@intel.com> CC: Zhao Yakui <yakui.zhao@intel.com> CC: Venki Pallipadi <venkatesh.pallipadi@intel.com> CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Mon, 30 Mar 2009 17:48:18 +0000 (17:48 +0000)]
ACPI: button: use .notify method instead of installing handler directly
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Note that events from fixed hardware buttons now show up as a special
notify event, so to preserve user-space backward compatibility, we
convert that back to ACPI_BUTTON_NOTIFY_STATUS.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Reviewed-by: Alex Chiang <achiang@hp.com> CC: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Mon, 30 Mar 2009 17:48:13 +0000 (17:48 +0000)]
ACPI: support acpi_device_ops .notify methods
This patch adds support for ACPI device driver .notify() methods. If
such a method is present, Linux/ACPI installs a handler for device
notifications (but not for system notifications such as Bus Check,
Device Check, etc). When a device notification occurs, Linux/ACPI
passes it on to the driver's .notify() method.
In most cases, this removes the need for drivers to install their own
handlers for device-specific notifications.
For fixed hardware devices like some power and sleep buttons, there's
no notification value because there's no control method to execute a
Notify opcode. When a fixed hardware device generates an event, we
handle it the same as a regular device notification, except we send
a ACPI_FIXED_HARDWARE_EVENT value. This is outside the normal 0x0-0xff
range used by Notify opcodes.
Several drivers install their own handlers for system Bus Check and
Device Check notifications so they can support hot-plug. This patch
doesn't affect that usage.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Reviewed-by: Alex Chiang <achiang@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
Johannes Berg [Mon, 30 Mar 2009 10:02:35 +0000 (12:02 +0200)]
toshiba-acpi: remove MAINTAINERS entry
"I'm not much opposed to marking this driver orphaned. I haven't used
a Toshiba laptop in four years or so, and disagree with the recent
additions of bluetooth and wireless control to the driver.
--John"
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: John Belmonte <john@neggie.net> Signed-off-by: Len Brown <len.brown@intel.com>
Make non-compat preadv/pwritev use native register size
Instead of always splitting the file offset into 32-bit 'high' and 'low'
parts, just split them into the largest natural word-size - which in C
terms is 'unsigned long'.
This allows 64-bit architectures to avoid the unnecessary 32-bit
shifting and masking for native format (while the compat interfaces will
obviously always have to do it).
This also changes the order of 'high' and 'low' to be "low first". Why?
Because when we have it like this, the 64-bit system calls now don't use
the "pos_high" argument at all, and it makes more sense for the native
system call to simply match the user-mode prototype.
This results in a much more natural calling convention, and allows the
compiler to generate much more straightforward code. On x86-64, we now
generate
which isn't _that_ horrible, but it does show how the natural word size
is just a more sensible interface (same arguments will hold in the user
level glibc wrapper function, of course, so the kernel side is just half
of the equation!)
Note: in all cases the user code wrapper can again be the same. You can
just do
or something like that. That way the user mode wrapper will also be
nicely passing in a zero (it won't actually have to do the shifts, the
compiler will understand what is going on) for the last argument.
And that is a good idea, even if nobody will necessarily ever care: if
we ever do move to a 128-bit lloff_t, this particular system call might
be left alone. Of course, that will be the least of our worries if we
really ever need to care, so this may not be worth really caring about.
[ Fixed for lost 'loff_t' cast noticed by Andrew Morton ]
Acked-by: Gerd Hoffmann <kraxel@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-api@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: Ingo Molnar <mingo@elte.hu> Cc: Ralf Baechle <ralf@linux-mips.org>> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sat, 10 Jan 2009 19:19:05 +0000 (14:19 -0500)]
ACPI: battery: asynchronous init
The battery driver tends to take quite some time to initialize
(100ms-300ms is quite typical).
This patch initializes the batter driver asynchronously, so that other
things in the kernel can initialize in parallel to this 300 msec.
As part of this, the battery driver had to move to the back
of the ACPI init order (hence the Makefile change).
Without this move, the next ACPI driver would just block
on the ACPI/devicee layer semaphores until the battery driver was
done anyway, not gaining any boot time.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Andy Whitcroft [Sat, 4 Apr 2009 08:33:34 +0000 (09:33 +0100)]
acer-wmi: Cleanup the failure cleanup handling
Cleanup the failure cleanup handling for brightness and email led.
[cc: Split out from another patch]
Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 4 Apr 2009 08:33:29 +0000 (09:33 +0100)]
acer-wmi: Blacklist Acer Aspire One
The Aspire One's ACPI-WMI interface is a placeholder that does nothing,
and the invalid results that we get from it are now causing userspace
problems as acer-wmi always returns that the rfkill is enabled (i.e. the
radio is off, when it isn't). As it's hardware controlled, acer-wmi
isn't needed on the Aspire One either.
Thanks to Andy Whitcroft at Canonical for tracking down Ubuntu's userspace
issues to this.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Reported-by: Andy Whitcroft <apw@canonical.com> Cc: stable@kernel.org Signed-off-by: Len Brown <len.brown@intel.com>
PCI still doesn't work on sh7785lcr 29bit 256M map mode.
On SH7785, PCI -> SHwy address translation is not base+offset but
somewhat like base|offset (See HW Manual (rej09b0261) Fig. 13.11).
So, you can't export CS2,3,4,5 by 256M at CS2 (results CS0,1,2,3
exported, I guess). There are two candidates.
a) 128M@CS2 + 128M@CS4
b) 512M@CS0
Attached patch is B. It maps 512M Byte at 0 independently of memory
size. It results CS0 to CS6 and perhaps some more being accessible
from PCI.
Tested on
7785lcr 29bit 128M map
7785lcr 29bit 256M map
(NOT tested on 32bit)
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Sat, 4 Apr 2009 15:40:22 +0000 (11:40 -0400)]
sh: Fix up number of on-chip DMA channels on SH7091.
This accidentally regressed when the multi-IRQ changes went in,
switching SH7091 from 4 to 6 channels. Add SH7091 back in to the
4-channel dependency list.
Reported-by: Adrian McMenamin <adrian@mcmen.demon.co.uk> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Refactor and redesign the brightness control backend...
In order to fix bugzilla #11750...
Add a new brightness control mode: support direct NVRAM checkpointing
of the backlight level (i.e. store directly to NVRAM without the need
for UCMS calls), and use that together with the EC-based control.
Disallow UCMS+EC, thus avoiding races with the SMM firmware.
Switch the models that define HBRV (EC Brightness Value) in the DSDT
to the new mode. These are: T40-T43, R50-R52, R50e, R51e, X31-X41.
Change the default for all other IBM ThinkPads to UCMS-only. The
Lenovo models already default to UCMS-only.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
thinkpad-acpi: enhanced debugging messages for rfkill subdrivers
Enhance debugging messages for all rfkill subdrivers in thinkpad-acpi.
Also, log a warning if the deprecated sysfs attributes are in use.
These attributes are going to be removed sometime in 2010.
There is an user-visible side-effect: we now coalesce attempts to
enable/disable bluetooth or WWAN in the procfs interface, instead of
hammering the firmware with multiple requests.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
thinkpad-acpi: restrict access to some firmware LEDs
Some of the ThinkPad LEDs indicate critical conditions that can cause
data loss or cause hardware damage when ignored (e.g. force-ejecting
a powered up bay; ignoring a failing battery, or empty battery; force-
undocking with the dock buses still active, etc).
On almost all ThinkPads, LED access is write-only, and the firmware
usually does fire-and-forget signaling on them, so you effectively
lose whatever message the firmware was trying to convey to the user
when you override the LED state, without any chance to restore it.
Restrict access to all LEDs that can convey important alarms, or that
could mislead the user into incorrectly operating the hardware. This
will make the Lenovo engineers less unhappy about the whole issue.
Allow users that really want it to still control all LEDs, it is the
unaware user that we have to worry about.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
The HKEY disable functionality basically cripples the entire event
model of the ThinkPad firmware and of the thinkpad-acpi driver.
Remove this functionality from the driver. HKEY must be enabled at
all times while thinkpad-acpi is loaded, and disabled otherwise.
For sysfs, according to the sysfs ABI and the thinkpad-acpi sysfs
rules of engagement, we will just remove the attributes. This will be
done in two stages: disable their function now, after two kernel
releases, remove the attributes.
For procfs, we call WARN(). If nothing triggers it, I will simply
remove the enable/disable commands entirely in the future along with
the sysfs attributes.
I don't expect much, if any fallout from this. There really isn't any
reason to mess with hotkey_enable or with the enable/disable commands
to /proc/acpi/ibm/hotkey, and this has been true for years...
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
thinkpad-acpi: add new debug helpers and warn of deprecated atts
Add a debug helper that discloses the TGID of the userspace task
attempting to access the driver. This is highly useful when dealing
with bug reports, since often the user has no idea that some userspace
application is accessing thinkpad-acpi...
Also add a helper to log warnings about sysfs attributes that are
deprecated.
Use the new helpers to issue deprecation warnings for bluetooth_enable
and wwan_enabled, that have been deprecated for a while, now.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
Add missing log levels in a standalone commit, to avoid dependencies in
future unrelated changes, just because they wanted to use one of the
missing log levels.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
The driver was renamed two years ago, on 2.6.21. Drop the old
compatibility alias, we have given everybody quite enough time
to update their configs to the new name.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
Harald Welte [Wed, 14 Jan 2009 06:01:17 +0000 (14:01 +0800)]
panasonic-laptop: use snprintf with PAGE_SIZE in sysfs attributes
Instead of just sprintf() into the page-sized buffer provided
by the sysfs/device_attribute API, we use snprintf with PAGE_SIZE
as an additional safeguard.
Signed-off-by: Martin Lucina <mato@kotelna.sk> Signed-off-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: Len Brown <len.brown@intel.com>
Harald Welte [Wed, 14 Jan 2009 05:59:50 +0000 (13:59 +0800)]
panasonic-laptop: Fix autoloading
This patch adds MODULE_DEVICE_TABLE() to panasonic-laptop.c in order
to ensure automatic loading of the module on systems with the respective
"MAT*" ACPI devices.
Signed-off-by: Martin Lucina <mato@kotelna.sk> Signed-off-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: Len Brown <len.brown@intel.com>
Matthew Garrett [Fri, 9 Jan 2009 20:17:11 +0000 (20:17 +0000)]
dell-wmi: new driver for hotkey control
Add a WMI driver for Dell laptops. Currently it does nothing but send a
generic input event when a button with a picture of a battery on it is
pressed, but maybe other uses will appear over time.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
(This is an update to the patch presented earlier in
http://lkml.org/lkml/2008/12/8/284, with new error handling.)
This patch sets the power of PnP ACPI devices to D0 when they
are activated and to D3 when they are disabled. The latter is
in correspondence with the ACPI 3.0 specification, whereas the
former is added in order to be able to power up a device after
it has been previously disabled (or when booting up a system).
(As a consequence, the patch makes the PnP ACPI code more ACPI
compliant.)
Section 6.2.2 of the ACPI Specification (at least versions 1.0b
and 3.0a) states: "Prior to running this control method [_DIS],
the OS[PM] will have already put the device in the D3 state."
Unfortunately, there is no clear statement as to when to put
a device in the D0 state. :-( Therefore, the patch executes the
method calls as _PS3/_DIS and _SRS/_PS0. What is clear: "If the
device is disabled, _SRS enables the device at the specified
resources." (From the ACPI 3.0a Specification.)
The patch fixes a problem with some IBM ThinkPads (at least the
600E and the 600X) where the serial ports have a dedicated
power source that needs to be brought up before the serial port
can be used. Without this patch, the serial port is enabled
but has no power. (In the past, the tpctl utility had to be
utilized to turn on the power, but support for this feature
stopped with version 5.9 as it did not support the more recent
kernel versions.)
The error handlers that handle any errors that can occur during
the power up/power down phases return the error codes to the
caller directly. Comments welcome! :-)
No regressions were observed on hardware that does not require
this patch.
The patch is applied against 2.6.27.x.
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net> Acked-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Merge branch 'stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
symbols, stacktrace: look up init symbols after module symbols
Merge branch 'rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: rcu_barrier VS cpu_hotplug: Ensure callbacks in dead cpu are migrated to online cpu
Merge branch 'ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
s390: remove arch specific smp_send_stop()
panic: clean up kernel/panic.c
panic, smp: provide smp_send_stop() wrapper on UP too
panic: decrease oops_in_progress only after having done the panic
generic-ipi: eliminate WARN_ON()s during oops/panic
generic-ipi: cleanups
generic-ipi: remove CSD_FLAG_WAIT
generic-ipi: remove kmalloc()
generic IPI: simplify barriers and locking
Merge branch 'locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking: rename trace_softirq_[enter|exit] => lockdep_softirq_[enter|exit]
lockdep: remove duplicate CONFIG_DEBUG_LOCKDEP definitions
lockdep: require framepointers for x86
lockdep: remove extra "irq" string
lockdep: fix incorrect state name
Suresh Siddha [Mon, 30 Mar 2009 21:55:30 +0000 (13:55 -0800)]
x86, ACPI: add support for x2apic ACPI extensions
All logical processors with APIC ID values of 255 and greater will have their
APIC reported through Processor X2APIC structure (type-9 entry type) and all
logical processors with APIC ID less than 255 will have their APIC reported
through legacy Processor Local APIC (type-0 entry type) only. This is the
same case even for NMI structure reporting.
The Processor X2APIC Affinity structure provides the association between the
X2APIC ID of a logical processor and the proximity domain to which the logical
processor belongs.
For OSPM, Procssor IDs outside the 0-254 range are to be declared as Device()
objects in the ACPI namespace.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: remove compat stuff
HID: constify arrays of struct apple_key_translation
HID: add support for Kye/Genius Ergo 525V
HID: Support Apple mini aluminum keyboard
HID: support for Kensington slimblade device
HID: DragonRise game controller force feedback driver
HID: add support for another version of 0e8f:0003 device in hid-pl
HID: fix race between usb_register_dev() and hiddev_open()
HID: bring back possibility to specify vid/pid ignore on module load
HID: make HID_DEBUG defaults consistent
HID: autosuspend -- fix lockup of hid on reset
HID: hid_reset_resume() needs to be defined only when CONFIG_PM is set
HID: fix USB HID devices after STD with autosuspend
HID: do not try to compile PM code with CONFIG_PM unset
HID: autosuspend support for USB HID
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6: (21 commits)
xtensa: we don't need to include asm/io.h
xtensa: only build platform or variant if they contain a Makefile
xtensa: make startup code discardable
xtensa: ccount clocksource
xtensa: remove platform rtc hooks
xtensa: use generic sched_clock()
xtensa: platform: s6105
xtensa: let platform override KERNELOFFSET
xtensa: s6000 variant
xtensa: s6000 variant core definitions
xtensa: variant irq set callbacks
xtensa: variant-specific code
xtensa: nommu support
xtensa: add flat support
xtensa: enforce slab alignment to maximum register width
xtensa: cope with ram beginning at higher addresses
xtensa: don't make bootmem bitmap larger than required
xtensa: fix init_bootmem_node() argument order
xtensa: use correct stack pointer for stack traces
xtensa: beat Kconfig into shape
...
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: BUG to BUG_ON changes
Btrfs: remove dead code
Btrfs: remove dead code
Btrfs: fix typos in comments
Btrfs: remove unused ftrace include
Btrfs: fix __ucmpdi2 compile bug on 32 bit builds
Btrfs: free inode struct when btrfs_new_inode fails
Btrfs: fix race in worker_loop
Btrfs: add flushoncommit mount option
Btrfs: notreelog mount option
Btrfs: introduce btrfs_show_options
Btrfs: rework allocation clustering
Btrfs: Optimize locking in btrfs_next_leaf()
Btrfs: break up btrfs_search_slot into smaller pieces
Btrfs: kill the pinned_mutex
Btrfs: kill the block group alloc mutex
Btrfs: clean up find_free_extent
Btrfs: free space cache cleanups
Btrfs: unplug in the async bio submission threads
Btrfs: keep processing bios for a given bdev if our proc is batching
Staging: serqt_usb: fix build due to proc tty changes
Just delete the proc tty usage in the driver as it's not needed and will
go away when it switches over to a usb-serial driver. This fixes the
build error in the driver.
projects / linux-2.6-omap-h63xx.git / log