[ARM] 3286/2: S3C2400 - adds to the table of supported CPUs
Patch from Lucas Correia Villa Real
Oops, sorry for the typo on name_s3c2400, a new patch is attached.
About GSTATUS1, S3C2400 doesn't have that register, so it's not
safe to use that memory address to identify its CPU.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support to GPIO on the S3C2400, which is going to
be used by the GP32 machine and the SMDK2400 development board.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russ Dill [Wed, 1 Feb 2006 21:07:28 +0000 (21:07 +0000)]
[ARM] 3295/1: Fix oprofile init return value
Patch from Russ Dill
The oprofile init code was broken in commit c6b9da. The new logic will
always return -ENODEV. This fixes oprofile_arch_init to return 0 on
success, and return the return value of spec->init() if applicable.
Signed-off-by: Russ Dill <Russ.Dill@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Wed, 1 Feb 2006 19:26:00 +0000 (19:26 +0000)]
[ARM] 3292/1: Fix memory corruption in asm-arm/checksum.h: ip_fast_csum()
Patch from Richard Purdie
ip_fast_csum() accesses memory via a pointer (iph) within an
asm function. To prevent memory corruption when the function is
inlined, it needs "memory" on the clobber list.
This fixes ip checksum errors reported by a Zaurus user.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Wed, 1 Feb 2006 19:25:58 +0000 (19:25 +0000)]
[ARM] 3290/1: Fix the FIFO size detection
Patch from Catalin Marinas
AACI reports TX FIFO full after the first write to it if the AC97 is not
enabled. This patch enables the AC97 probing before the check for the TX
FIFO size. The patch also adds a warning if the TX FIFO size is not
multiple of 16.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andi Kleen [Fri, 27 Jan 2006 01:03:50 +0000 (02:03 +0100)]
[PATCH] PCI: handle bogus MCFG entries
Handle more bogus MCFG entries
Some Asus P4 boards seem to have broken MCFG tables with
only a single entry for busses 0-0. Special case these
and assume they mean all busses can be accessed.
[PATCH] powerpc/PCI hotplug: shuffle error checking to better location.
Error checking is scattered through various layers of the dlpar code,
leading to a somewhat opaque code structure. This patch consolidates
error checking in one routine, simplifying the code a tad. There's
also some whitespace cleanup here too.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_enable_pci_slot()
has a fairly simple logic structure, once all of the debug printk's
are removed. Its called from only one place, and that place also
has a very simple structure once he printk's are removed. Merge
the two together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_unconfig_pci_adapter()
is really just three lines of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the thre lines.
Also, provide proper semaphore locking in the affected function
disable_slot()
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_config_pci_adapter()
is really just one line of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the one line.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_fixup_new_pci_devices() has been migrated to
pcibios_fixup_new_pci_devices() in
arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_find_pci_bus() has been migrated to
pcibios_find_pci_bus() in arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Keck, David [Mon, 16 Jan 2006 21:22:36 +0000 (15:22 -0600)]
[PATCH] PCI Hotplug: shpchp: AMD POGO errata fix
This patch fixes the AMD POGO errata on the hotplug controller where the
platform will lock up or reboot if PERR/SERR generation is enabled and a
slot is sent an enable command. This fix disables PERR/SERR generation
before a slot is sent the enable command by first saving related
registers, turning off SERR/PERR generation, enabling the slot, then
restoring the registers.
Signed-off-by: David Keck <david.keck@amd.com> Cc: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linas [Thu, 12 Jan 2006 20:36:25 +0000 (14:36 -0600)]
[PATCH] PCI Hotplug: PCI panic on dlpar add (add pci slot to running partition)
Removing and then adding a PCI slot to a running partition results in
a kernel panic. The current code attempts to add iospace for an entire
root bus, which is inappropriate, and silently fails. When a pci device
tries to use the iospace, a page fault is taken, as the iospace had not
been mapped, and of course the page fault cannot be resolved.
This only occurs for PCI adapters using pio, which may be why it hadn't
been seen earlier (this seems to have been broken for a while).
This patch has survived testing of dozens of slot add and removes.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Acked-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linas [Tue, 10 Jan 2006 21:15:47 +0000 (15:15 -0600)]
[PATCH] PCI Hotplug/powerpc: module build break
The RPAPHP hoplug driver will not build as a module, because it calls
on pci_claim_resource(), which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>
A grep indicates that building drivers/parisc/lba_pci.c
would have trouble building as a module for the same reason.
Mark Rustad [Fri, 6 Jan 2006 06:47:29 +0000 (22:47 -0800)]
[PATCH] PCI: restore 2 missing pci ids
Somewhere between 2.6.14 and 2.6.15-rc3, some PCI ids were apparently
removed. The ecc.c module, which is not a part of the kernel.org tree, but
included in some distributions, fails to compile.
Signed-off-by: Mark Rustad <mrustad@mac.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[IPV6] tcp_v6_send_synack: release the destination
This patch fix dst reference counting in tcp_v6_send_synack
Analysis:
Currently tcp_v6_send_synack is never called with a dst entry
so dst always comes in as NULL.
ip6_dst_lookup calls ip6_route_output which calls dst_hold
before it returns the dst entry. Neither xfrm_lookup
nor tcp_make_synack consume the dst entry so we still have
a dst_entry with a bumped refrence count at the end of
this function.
Therefore we need to call dst_release just before we return
just like tcp_v4_send_synack does.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a simpler fix for the two races in bridge device removal.
The Xen race of delif and notify is managed now by a new deleted flag.
No need for barriers or other locking because of rtnl mutex.
The del_timer_sync()'s are unnecessary, because br_stp_disable_port
delete's the timers, and they will finish running before RCU callback.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 1 Feb 2006 01:35:35 +0000 (17:35 -0800)]
[IPV4]: Always set fl.proto in ip_route_newports
ip_route_newports uses the struct flowi from the struct rtable returned
by ip_route_connect for the new route lookup and just replaces the port
numbers if they have changed. If an IPsec policy exists which doesn't match
port 0 the struct flowi won't have the proto field set and no xfrm lookup
is done for the changed ports.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David Brownell [Fri, 20 Jan 2006 22:38:49 +0000 (14:38 -0800)]
[PATCH] USB: gadget zero and dma-coherent buffers
This makes sure that the correct length is reported when freeing
a dma-coherent buffer; some platforms complain if that's wrong.
It also makes two parameters readonly in sysfs, as they're not
safe to change while tests are running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 20 Jan 2006 22:44:12 +0000 (14:44 -0800)]
[PATCH] USB: USB authentication states
Another hook needed for wireless USB: there are states associated with the
device authentication protocol. Wireless devices must authenticate using
the host system's keystore.
Note that wired connections could also use this authentication protocol, if
for no other reason than to support the most secure "simple" key exchange
protocols for wireless devices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Tue, 17 Jan 2006 23:39:25 +0000 (15:39 -0800)]
[PATCH] USB: libusual: fix warning on 64bit boxes
We cast an int to a void * which not unreasonably makes gcc suspicious.
We don't actually care what type "type" is so use unsigned long so it
matches pointer length on all platforms.
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk [Fri, 6 Jan 2006 02:28:52 +0000 (03:28 +0100)]
[PATCH] USB: drivers/usb/media/ov511.c: remove hooks for the decomp module
- the decomp module is not intended for inclusion into the kernel
- people using the decomp module from upstream will usually simply use
the complete upstream 2.xx driver
Therefore, there seems to be no good reason spending some bytes of
kernel memory for hooks for this module.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Mark McClelland <mark@ovcam.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk [Sun, 8 Jan 2006 23:43:39 +0000 (00:43 +0100)]
[PATCH] USB: drivers/usb/media/w9968cf.c: remove hooks for the vpp module
- the w9968cf-vpp module is not intended for inclusion into the kernel
- the upstream w9968cf package shipping the w9968cf-vpp module suggests
to simply replace the w9968cf module shipped with the kernel
Therefore, there seems to be no good reason spending some bytes of
kernel memory for hooks for the w9968cf-vpp module.
Alan Stern [Tue, 3 Jan 2006 15:30:31 +0000 (10:30 -0500)]
[PATCH] USB: gadgetfs: set "zero" flag for short control-IN response
This patch (as622) makes gadgetfs set the "zero" flag for control-IN
responses, when the length of the response is shorter than the length of
the request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Olav Kongas [Tue, 27 Dec 2005 14:04:02 +0000 (16:04 +0200)]
[PATCH] USB: isp116x-hcd: replace mdelay() by msleep()
Replace mdelay() by msleep() in bus_suspend(); the rest of the system will
gain 7ms. The related code is reorganized to minimize the number of
locking/unlocking calls.
The last hunk of the patch is the formatting change by Lindent.
Signed-off-by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 23 Jan 2006 22:17:21 +0000 (17:17 -0500)]
[PATCH] USB: UHCI: No FSBR until device is configured
Some USB devices don't enumerate well with FSBR turned on. This patch
keeps devices on the low-speed part of the schedule (which doesn't use
FSBR) until they have been fully configured.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vojtech Pavlik [Thu, 26 Jan 2006 06:44:31 +0000 (07:44 +0100)]
[PATCH] USB HID: add blacklist entry for HP keyboard
My earlier experiment (adding a clear-halt for the interrupt-in
endpoint) failed. It turns out that it does cause problems for other
devices. And it wasn't needed anyway; a simple blacklist entry was
enough to get my HP keyboard working.
This patch (as643) removes the clear-halt call and adds the blacklist
entry.
matthieu castet [Wed, 18 Jan 2006 06:39:27 +0000 (07:39 +0100)]
[PATCH] UEAGLE : cmv name bug (was cosmetic)
this patch correct a possible bug with cmv_name being static. If there
is 2 modems and the driver is scheduled when filling cmv_name this could
result with garbage in cmv_name. We allocate cmv_name on the stack but
with a small size in order to avoid that.
matthieu castet [Wed, 18 Jan 2006 06:38:19 +0000 (07:38 +0100)]
[PATCH] UEAGLE : add iso support
This patch adds the support for isochronous pipe.
A new module parameter is added to select iso mode. It is set to iso by
default because bulk mode doesn't work well at high speed rate (>3 Mbps
for upload).
We use UDSL_IGNORE_EILSEQ flags because ADI firmware doesn't reply to
ISO IN when it has nothing to send [1].
[1]
from cypress datasheet :
The ISOSEND0 Bit (bit 7 in the USBPAIR Register) is used when the EZ-USB
FX chip receives an isochronous IN token while the IN FIFO is empty. If
ISOSEND0=0 (the default value), the USB core does not respond to the IN
token. If ISOSEND0=1, the USB core sends a zero-length data packet in
response to the IN token. The action to take depends on the overall
system design. The ISOSEND0 Bit applies to all of the isochronous IN
endpoints, IN-8 through IN-15.
Arjan van de Ven [Fri, 13 Jan 2006 14:52:55 +0000 (15:52 +0100)]
[PATCH] USBATM: semaphore to mutex conversion
This is the usbatm part of the Arjan, Jes and Ingo
mass semaphore to mutex conversion, reworked to apply on top
of the patches I just sent to you. This time, with correct
attribution and signed-off lines.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Duncan Sands [Fri, 13 Jan 2006 10:12:58 +0000 (11:12 +0100)]
[PATCH] USBATM: -EILSEQ workaround
Don't throttle on -EILSEQ urb status if requested by a minidriver.
It seems the ueagle modems are buggy, giving -EILSEQ when they
have no data to send. The ueagle change will be sent separately
by the ueagle guys. Patch by Matthieu Castet.
Duncan Sands [Fri, 13 Jan 2006 10:06:46 +0000 (11:06 +0100)]
[PATCH] USBATM: handle urbs containing partial cells
The receive logic has always assumed that urbs contain an integral
number of ATM cells, which is a bit naughty, though it never caused
any problems with bulk transfers. Isochronous urbs spank us soundly
for this. Fixed thanks to this patch, mostly by Stanislaw Gruszka.
Duncan Sands [Fri, 13 Jan 2006 09:59:23 +0000 (10:59 +0100)]
[PATCH] USBATM: allow isochronous transfer
While the usbatm core has had some support for using isoc urbs
for some time, there was no way for users to turn it on. While
use of isoc transfer should still be considered experimental, it
now works well enough to let users turn it on. Minidrivers signal
to the core that they want to use isoc transfer by setting the new
UDSL_USE_ISOC flag. The speedtch minidriver gets a new module
parameter enable_isoc (defaults to false), plus some logic that
checks for the existence of an isoc receive endpoint (not all
speedtouch modems have one).
Duncan Sands [Fri, 13 Jan 2006 09:52:38 +0000 (10:52 +0100)]
[PATCH] USBATM: measure buffer size in bytes; force valid sizes
Change the module parameters rcv_buf_size and snd_buf_size to
specify buffer sizes in bytes rather than ATM cells. Since
there is some danger that users may not notice this change,
the parameters are renamed to rcv_buf_bytes etc. The transmit
buffer needs to be a multiple of the ATM cell size in length,
while the receive buffer should be a multiple of the endpoint
maxpacket size (this wasn't enforced before, which causes trouble
with isochronous transfers), so enforce these restrictions. Now
that the usbatm probe method inspects the endpoint maxpacket size,
minidriver bind routines need to set the correct alternate setting
for the interface in their bind routine. This is the reason for
the speedtch changes.
Duncan Sands [Fri, 13 Jan 2006 09:13:19 +0000 (10:13 +0100)]
[PATCH] USBATM: use dev_kfree_skb_any rather than dev_kfree_skb
In one spot (usbatm_cancel_send) we were calling dev_kfree_skb with irqs
disabled. This mistake is just too easy to make, so systematically use
dev_kfree_skb_any rather than dev_kfree_skb.
Duncan Sands [Fri, 13 Jan 2006 09:05:15 +0000 (10:05 +0100)]
[PATCH] USBATM: shutdown open connections when disconnected
This patch causes vcc_release_async to be applied to any open
vcc's when the modem is disconnected. This signals a socket
shutdown, letting the socket user know that the game is up.
I wrote this patch because of reports that pppd would keep
connections open forever when the modem is disconnected.
This patch does not fix that problem, but it's a step in the
right direction. It doesn't help because the pppoatm module
doesn't yet monitor state changes on the ATM socket, so simply
never realises that the ATM connection has gone down (meaning
it doesn't tell the ppp layer). But at least there is a socket
state change now. Unfortunately this patch may create problems
for those rare users like me who use routed IP or some other
non-ppp connection method that goes via the ATM ARP daemon: the
daemon is buggy, and with this patch will crash when the modem
is disconnected. Users with a buggy atmarpd can simply restart
it after disconnecting the modem.
Duncan Sands [Fri, 13 Jan 2006 08:48:36 +0000 (09:48 +0100)]
[PATCH] USBATM: xusbatm rewrite
The xusbatm driver is for otherwise unsupported modems.
All it does is grab hold of a user-specified set of
interfaces - the generic usbatm core methods (hopefully)
do the rest. As Aurelio Arroyo discovered when he tried
to use xusbatm (big mistake!), the interface grabbing logic
was completely borked. Here is a rewrite that works.
Duncan Sands [Tue, 17 Jan 2006 10:16:13 +0000 (11:16 +0100)]
[PATCH] USBATM: add flags field
Have minidrivers and the core signal special requirements
using a flags field in struct usbatm_data. For the moment
this is only used to replace the need_heavy_init bind
parameter, but there'll be new flags in later patches.
Luca Risolia [Fri, 13 Jan 2006 17:19:43 +0000 (17:19 +0000)]
[PATCH] USB: SN9C10x driver updates
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
This patch corrects the URB initialisation for transfers
like this is done in other drivers too.
Without this patch no data was transmitted on a PXA270 OHCI
platform. May apply to others too.
Luca Risolia [Thu, 5 Jan 2006 18:14:04 +0000 (18:14 +0000)]
[PATCH] USB: SN9C10x driver updates and bugfixes
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Matthew Dharm [Sat, 31 Dec 2005 03:06:53 +0000 (19:06 -0800)]
[PATCH] USB: usb-storage: Add support for Rio Karma
This patch from Bob Copeland adds support for the Rio Karma portable
digital audio player to the usb-storage driver. The only thing needed to
support this device is a one-time (per plugin) init command which is sent
to the device.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So it picked up my UPS, and loaded the driver.
Whilst no harm came, because it later checks the vendor/product IDs,
this driver should probably be rewritten to only probe
for the device IDs it actually knows about.
Rui Santos [Mon, 9 Jan 2006 13:12:40 +0000 (13:12 +0000)]
[PATCH] USB: ftdi: Two new ATIK based USB astronomical CCD cameras
Documentation: Specify grayscale specification on ATIK-ATK16
and ATIK-ATK16HR comments.
New: Add ProductID and VendorID for devices ATIK-ATK16C and
ATIK-ATK16HRC. These devices are also USB Astronomical CCD
cameras that work through an FTDI 245BM chip, share the
same base hardware but, it has a colour CCD chip instead
of a grayscale one.
Wouter Paesen [Tue, 3 Jan 2006 13:30:31 +0000 (14:30 +0100)]
[PATCH] USB: ftdi_sio: new PID for PCDJ DAC2
The attached patch adds a new PID for the ftdi_sio driver. It will
enable support for PC-DJ's DAC-2 controller module
(more information on http://www.pcdjhardware.com/DAC2.asp)
Ian Abbott [Mon, 9 Jan 2006 17:11:40 +0000 (17:11 +0000)]
[PATCH] USB: ftdi_sio: new IDs for Westrex devices
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Cory Lee to support two POS
printers made by Westrex International (Model 777 and Model 8900F).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch includes the Vendor Id for a optic fiber to USB device named
TTUSB from thought Technology. It's just add the vendor Id to
ftdi_sio.h and add the Vendor ID and model Id to table_combined.
Signed-off-by: Louis Nyffenegger <louis.nyffenegger@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 5 Jan 2006 08:26:30 +0000 (00:26 -0800)]
[PATCH] USB: ub 05 Bulk reset
For crying out loud, they have devices which do not like port resets.
So, do what usb-storage does and try both bulk and port resets.
We start with a port reset (which usb-storage does at the end of transport),
then do a Bulk reset, then a port reset again. This seems to work for me.
The code is getting dirtier and dirtier here, but I swear that I'll
do something about it (see those two new XXX). Honest.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6-omap-h63xx.git / log