David Brownell [Sat, 24 Nov 2007 07:20:05 +0000 (23:20 -0800)]
i2c init section fixes
Fix init section warnings in the new i2c init code. It's
wrong to call "__init" functions from non-__init ones.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
MMC: OMAP: Enabling MMC/SD card support option on n800_defconfig
Enables MMC/SD card support option on n800_defconfig to use MMC multislot support.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Refreshed to apply after Lauri's patch. Also left out
CONFIG_MMC_BLOCK_BOUNCE as omap MMC supports SG.
Felipe Balbi [Mon, 26 Nov 2007 16:01:58 +0000 (12:01 -0400)]
MMC: OMAP: Make board-h2.c uses new board-h2-mmc.c code
Make board-h2.c file uses new board-h2-mmc.c code.
This patch also:
- Introduces a new gpio_switch to get events when inserting and removing
MMC/SD/SDIO cards to/from the slot.
- Enables the following options on omap_h2_1610_defconfig to use
multislot support:
- GPIO switch support
- MMC/SD card support
- VFAT fs support
- NLS ISO 8859-1
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: David Cohen <david.cohen@indt.org.br> Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Mon, 26 Nov 2007 16:01:54 +0000 (12:01 -0400)]
MMC: OMAP: Supporting MMC multislot structures for TI OMAP H2 board
Proposes the new board-h2-mmc.c file to handle all the mmc
specific code for multislot support.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: David Cohen <david.cohen@indt.org.br> Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Mon, 26 Nov 2007 16:01:49 +0000 (12:01 -0400)]
MMC: OMAP: Make board-h3.c uses new board-h3-mmc.c code
Make board-h3.c file uses new board-h3-mmc.c code.
This patch also:
- Introduces a new gpio_switch to get events when inserting and removing
MMC/SD/SDIO cards to/from the slot.
- Enables the following options on omap_h3_1710_defconfig to use
multislot support:
- GPIO switch support
- MSDOS fs support
- VFAT fs support
- Codepage 437
- NLS ISO 8859-1
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: David Cohen <david.cohen@indt.org.br> Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Mon, 26 Nov 2007 16:01:45 +0000 (12:01 -0400)]
MMC: OMAP: Supporting MMC multislot structures for TI OMAP H3 board
Proposes the new board-h3-mmc.c file to handle all the mmc
specific code for multislot support.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: David Cohen <david.cohen@indt.org.br> Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Lavinen [Mon, 26 Nov 2007 16:01:38 +0000 (12:01 -0400)]
MMC: OMAP: Modifications at N800 MMC board specific file to work MMC multislot support
Modifications at board-n800-mmc.c and board-n800.c files to work with MMC multislot support.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
PLAT: OMAP: Modifications at devices.c and mmc.h to use multislot structures
Modifications at arch/arm/plat-omap/devices.c and include/asm-arm/arch-omap/mmc.h
to use multislot structures.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Lavinen [Mon, 26 Nov 2007 16:01:27 +0000 (12:01 -0400)]
MMC: OMAP: Abort stuck commands
When a card is removed while it is being accessed, a command can get stuck so
that no timeout or end of command interrupt ever occurs. The command getting
stuck is almost always CDM12, but also the other commands can get stuck. Catch
a stuck command with a timer and try sending the initiliazation stream until
the controller starts running again and responds with the end of command
status.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Mon, 26 Nov 2007 16:01:22 +0000 (12:01 -0400)]
MMC: OMAP: General cleanup for MMC multislot support
General code cleanup, modifications at some dev_* functions and
other hacks at mmc_omap_irq() for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Mon, 26 Nov 2007 16:01:18 +0000 (12:01 -0400)]
MMC: OMAP: Power functions modified to MMC multislot support
Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Mon, 26 Nov 2007 16:01:13 +0000 (12:01 -0400)]
MMC: OMAP: Fix timeout calculation for MMC multislot support
Fix the data timeout calculation for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds back MMC cover switch support in a way that
supports multiple slots.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Juha Yrjola [Wed, 28 Nov 2007 01:50:42 +0000 (17:50 -0800)]
OMAP: MMC: Introduce new multislot structure and change driver to use it
Introduce new MMC multislot structure and change driver to use it.
Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark Fasheh [Tue, 20 Nov 2007 19:56:39 +0000 (11:56 -0800)]
ocfs2: reverse inline-data truncate args
ocfs2_truncate() and ocfs2_remove_inode_range() had reversed their "set
i_size" arguments to ocfs2_truncate_inline(). Fix things so that truncate
sets i_size, and punching a hole ignores it.
This exposed a problem where punching a hole in an inline-data file wasn't
updating the page cache, so fix that too.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Thu, 8 Nov 2007 00:35:14 +0000 (16:35 -0800)]
ocfs2: Remove bug statement in ocfs2_dentry_iput()
The existing bug statement didn't take into account unhashed dentries which
might not have a cluster lock on them. This could happen if a node exporting
the file system via NFS is rebooted, re-exported to nfs clients and then
unmounted. It's fine in this case to not have a dentry cluster lock.
Just remove the bug statement and replace it with an error print, which
does the proper checks. Though we want to know if something has happened
which might have prevented a cluster lock from being created, it's
definitely not necessary to panic the machine for this.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Jan Kara [Tue, 13 Nov 2007 18:59:33 +0000 (19:59 +0100)]
[PATCH] ocfs2: Remove expensive bitmap scanning
Enable expensive bitmap scanning only if DEBUG option is enabled.
The bitmap scanning quite loads the CPU and on my machine the write
throughput of dd if=/dev/zero of=/ocfs2/file bs=1M count=500 conv=sync
improves from 37 MB/s to 45.4 MB/s in local mode...
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Tue, 20 Nov 2007 02:40:16 +0000 (18:40 -0800)]
ocfs2: log valid inode # on bad inode
If the inode block isn't valid then we don't want to print the value from
that, instead print the block number which was passed in (which should
always be correct). Also, turn this into a debug print for now - folks who
hit an actual problem always have other logs indicating what the source is.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Linus Torvalds [Tue, 27 Nov 2007 22:27:56 +0000 (14:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: SVM: Fix FPU leak while emulating clts
KVM: SVM: Unload guest fpu on vcpu_put()
KVM: x86 emulator: Use emulator_write_emulated and not emulator_write_std
KVM: x86 emulator: fix the saving of of the eip value
KVM: x86 emulator: fix JMP_REL
Linus Torvalds [Tue, 27 Nov 2007 22:20:51 +0000 (14:20 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add missing counter increment in iser_data_buf_aligned_len()
IB/ehca: Fix static rate regression
mlx4_core: Fix state check in mlx4_qp_modify()
IB/ipath: Normalize error return codes for posting work requests
IB/ipath: Fix offset returned to ibv_modify_srq()
IB/ipath: Fix error path in QP creation
IB/ipath: Fix offset returned to ibv_resize_cq()
Linus Torvalds [Tue, 27 Nov 2007 22:20:35 +0000 (14:20 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: adds the context menu key (HUT GenDesc 0x84)
Input: add definitions for frame forward and frame back keys
Input: bf54x-keys - keypad does not exist on BF544 parts
Input: gpio-keys - request and configure GPIOs
Input: i8042 - add i8042.noloop quirk for MS Virtual Machine
Sonypi: use synchronize_irq instead of sycnronize_sched
sonypi: fit input devices into sysfs tree
sony-laptop: fit input devices into sysfs tree
Andrew Morton [Tue, 27 Nov 2007 20:35:56 +0000 (21:35 +0100)]
amd74xx: arm hack
drivers/ide/pci/amd74xx.c: In function `init_hwif_amd74xx':
drivers/ide/pci/amd74xx.c:387: error: implicit declaration of function `pci_get_legacy_ide_irq'
Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
aec62xx: Fix kernel oops in driver's probe function
Add pci_enable_device() to aec62xx probe function
before doing any I/O.
Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR
is 0 and the following inb() causes a kernel oops.
Jonas Stare [Tue, 27 Nov 2007 20:35:53 +0000 (21:35 +0100)]
ide: skip ide_wait_not_busy() on noprobe-disks
There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).
If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.
The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.
Bart: minor cleanups
Signed-off-by: Jonas Stare <jonas.stare@purplescout.se> CC: Andrew Morton <akpm@linux-foundation.org>, Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 27 Nov 2007 20:35:53 +0000 (21:35 +0100)]
siimage: remove resetproc() method
The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 27 Nov 2007 20:35:52 +0000 (21:35 +0100)]
ide: don't set PIO mode on pre-EIDE drives
Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Izik Eidus [Sun, 11 Nov 2007 12:40:48 +0000 (14:40 +0200)]
KVM: x86 emulator: fix JMP_REL
Change JMP_REL to call to register_address_increment(): the operands size
should not effect the calculation of the eip, instead the ad_bytes should
affect it.
Signed-off-by: Izik Eidus <izike@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
blktrace: Make sure BLKTRACETEARDOWN does the full cleanup.
if blktrace program segfault it will not be able
to call BLKTRACETEARDOWN. Now if we run the blktrace
again that would result in a failure to create the
block/<device> debugfs directory.This will result
in blk_remove_root() to be called which will set
blk_tree_root to NULL. But the debugfs block dir
still exist because it contain subdirectory.
Now if we try to fix it using BLKTRACETEARDOWN
it won't work because blk_tree_root is NULL.
Fix the same.
Tested as below
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
Segmentation fault
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
BLKTRACESETUP: No such file or directory
Failed to start trace on /dev/hdc
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -k /dev/hdc
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (41 commits)
[XFRM]: Fix leak of expired xfrm_states
[ATM]: [he] initialize lock and tasklet earlier
[IPV4]: Remove bogus ifdef mess in arp_process
[SKBUFF]: Free old skb properly in skb_morph
[IPV4]: Fix memory leak in inet_hashtables.h when NUMA is on
[IPSEC]: Temporarily remove locks around copying of non-atomic fields
[TCP] MTUprobe: Cleanup send queue check (no need to loop)
[TCP]: MTUprobe: receiver window & data available checks fixed
[MAINTAINERS]: tlan list is subscribers-only
[SUNRPC]: Remove SPIN_LOCK_UNLOCKED
[SUNRPC]: Make xprtsock.c:xs_setup_{udp,tcp}() static
[PFKEY]: Sending an SADB_GET responds with an SADB_GET
[IRDA]: Compilation for CONFIG_INET=n case
[IPVS]: Fix compiler warning about unused register_ip_vs_protocol
[ARP]: Fix arp reply when sender ip 0
[IPV6] TCPMD5: Fix deleting key operation.
[IPV6] TCPMD5: Check return value of tcp_alloc_md5sig_pool().
[IPV4] TCPMD5: Use memmove() instead of memcpy() because we have overlaps.
[IPV4] TCPMD5: Omit redundant NULL check for kfree() argument.
ieee80211: Stop net_ratelimit/IEEE80211_DEBUG_DROP log pollution
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] api: Fix potential race in crypto_remove_spawn
[CRYPTO] authenc: Move initialisations up to shut up gcc
Linus Torvalds [Tue, 27 Nov 2007 03:42:59 +0000 (19:42 -0800)]
Merge git://git.linux-nfs.org/pub/linux/nfs-2.6
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFS: Clean up new multi-segment direct I/O changes
NFS: Ensure we return zero if applications attempt to write zero bytes
NFS: Support multiple segment iovecs in the NFS direct I/O path
NFS: Introduce iovec I/O helpers to fs/nfs/direct.c
SUNRPC: Add missing "space" to net/sunrpc/auth_gss.c
SUNRPC: make sunrpc/xprtsock.c:xs_setup_{udp,tcp}() static
NFS: fs/nfs/dir.c should #include "internal.h"
NFS: make nfs_wb_page_priority() static
NFS: mount failure causes bad page state
SUNRPC: remove NFS/RDMA client's binary sysctls
kernel BUG at fs/nfs/namespace.c:108! - can be triggered by bad server
sunrpc: rpc_pipe_poll may miss available data in some cases
sunrpc: return error if unsupported enctype or cksumtype is encountered
sunrpc: gss_pipe_downcall(), don't assume all errors are transient
NFS: Fix the ustat() regression
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
Linus Torvalds [Tue, 27 Nov 2007 03:40:27 +0000 (19:40 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (56 commits)
Blackfin arch: fix bug when enable uart1 with uart0 disabled => no initial console
Blackfin arch: split apart dump_bfin_regs and merge/remove show_regs from process.c, which was largely duplicated
Blackfin arch: use common __INIT/__FINIT defines rather than setting the .section ourselves to .init.text
Blackfin arch: fix bug when sending signals with the wrong PC, cause gdb get confused
Blackfin arch: Ensure we printk out strings with the proper loglevel
Blackfin arch: Need to specify ax with the .init.text section,
Blackfin arch: Update Kconfig to latest Blackfin silicon datasheets
Blackfin arch: update defconfig files
Blackfin arch: Fix typo, and add ENDPROC - no functional changes
Blackfin arch: convert READY to DMA_READY as it causes build errors in common sound code otherwise
Blackfin arch: add defines for the on-chip L1 ROM of BF54x
Blackfin arch: cplb and map header file cleanup
Blackfin arch: cleanup the cplb declares
Blackfin arch: fix broken on BF52x, remove silly checks on processors for L1_SCRATCH defines
Blackfin arch: add support for working around anomaly 05000312
Blackfin arch: cleanup BF54x header file and add BF547 definition
Blackfin arch: fix building for BF542 processors which only have 1 TWI
Blackfin arch: rename _return_from_exception to _bfin_return_from_exception and export it
Blackfin arch: move EXPORT_SYMBOL() to C files where the symbol is actually defined
Blackfin arch: fix bug NOR Flash MTD mount fail
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
sh: include ax88796 in the defconfig for r7785rp
sh: include ax88796 in the defconfig for r7780mp
sh: fix R2D-1 CF support
fb: Orphan imsttfb.
sh: Update mailing list info.
sh: lockless UTLB miss fast-path.
sh: Kill off UTLB flush in fast-path.
sh: Fix copy_{to,from}_user_page() with cache disabled.
Mikulas Patocka [Thu, 22 Nov 2007 20:26:01 +0000 (21:26 +0100)]
plip: fix parport_register_device name parameter
Plip passes a string "name" that is allocated on stack to
parport_register_device. parport_register_device holds the pointer to
"name" and when the registering function exits, it points nowhere.
On some machine, this bug causes bad names to appear in /proc, such as
/proc/sys/dev/parport/parport0/devices/T^/�X^/�, on others, the plip
proc node is completely missing.
The patch also fixes documentation to note this requirement.
Mikulas Patocka [Thu, 22 Nov 2007 20:19:39 +0000 (21:19 +0100)]
plip: use netif_rx_ni() for packet receive
netif_rx is meant to be called from interrupts because it doesn't wake
up ksoftirqd. For calling from outside interrupts, netif_rx_ni exists.
This fixes plip to use netif_rx_ni. It fixes the infamous error "NOHZ:
local_softirq_panding 08" that happens on some machines with NOHZ and
plip --- it is caused by the fact that softirq is pending and ksoftirqd
is sleeping.
Linus Torvalds [Tue, 27 Nov 2007 03:25:23 +0000 (19:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: Avoid re-using minor numbers before the original device is closed.
tifm_sd: handle non-power-of-2 block sizes
mmc_block: check card state after write
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix check after use error in ACL code
[CIFS] Fix potential data corruption when writing out cached dirty pages
[CIFS] Fix spurious reconnect on 2nd peek from read of SMB length
[CIFS] remove build warning
[CIFS] Have CIFS_SessSetup build correct SPNEGO SessionSetup request
[CIFS] minor checkpatch cleanup
[CIFS] have cifs_get_spnego_key get the hostname from TCP_Server_Info
[CIFS] add hostname field to TCP_Server_Info struct
[CIFS] clean up error handling in cifs_mount
[CIFS] add ver= prefix to upcall format version
[CIFS] Fix buffer overflow if server sends corrupt response to small
Linus Torvalds [Tue, 27 Nov 2007 03:18:22 +0000 (19:18 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: bump transfer chunk size if it's odd
libata: Return proper ATA INT status in pata_bf54x driver
pata_ali: trim trailing whitespace (fix checkpatch complaints)
pata_isapnp: Polled devices
pata_hpt37x: Fix cable detect bug spotted by Sergei
pata_ali: Lots of problems still showing up with small ATAPI DMA
pata_ali: Add Mitac 8317 and derivatives
libata-core: List more documentation sources for reference
ata_piix: Invalid use of writel/readl with iomap
sata_sil24: fix sg table sizing
pata_jmicron: fix disabled port handling in jmicron_pre_reset()
pata_sil680: kill bogus reset code (take 2)
ata_piix: port enable for the first SATA controller of ICH8 is 0xf not 0x3
ata_piix: only enable the first port on apple macbook pro
ata_piix: reorganize controller IDs
pata_sis.c: Add Packard Bell EasyNote K5305 to laptops
libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs
libata: use ATA_HORKAGE_STUCK_ERR for ATAPI tape drives
libata: workaround DRQ=1 ERR=1 for ATAPI tape drives
libata: remove unused functions
...
projects / linux-2.6-omap-h63xx.git / log