Paul Mundt [Wed, 26 Nov 2008 06:22:50 +0000 (15:22 +0900)]
sh: do not latency trace idle.
Description snipped from Steven Rostedt's PPC patch:
When idle is called, interrupts are blocked, but the idle
function will still wake up on an interrupt. The problem is
that the interrupt disabled latency tracer will take this call
to idle as a latency.
This patch disables the latency tracing when going into idle.
Paul Mundt [Tue, 25 Nov 2008 19:21:36 +0000 (04:21 +0900)]
sh: Re-add support for best fit ISA tuning if none is available.
This was removed in the libgcc integration, but there are still some
compilers that need this. We also relax the rules on the ISA tuning in
the cases where there are no matches for the CPU tuning and adopt the
-any default, which matches the intent of the isa-y target list. This
compensates for mismatches where binutils supports a wide array of
targets whilst the compiler is much more restricted.
Paul Mundt [Tue, 25 Nov 2008 15:29:58 +0000 (00:29 +0900)]
sh: Provide optimized unaligned loads on SH-4A.
This adds support for unaligned loads on SH-4A, using the SH-4A's
neutered movua.l instruction. As movua.l is r0-inspired, stores are
still handled through the packed struct.
Based on asm-generic/unaligned.h by Harvey Harrison.
Magnus Damm [Tue, 25 Nov 2008 12:57:29 +0000 (21:57 +0900)]
sh: P4 ioremap pass-through
This patch adds a pass-through case when ioremapping P4 addresses.
Addresses passed to ioremap() should be physical addresses, so the
best option is usually to convert the virtual address to a physical
address before calling ioremap. This will give you a virtual address
in P2 which matches the physical address and this works well for
most internal hardware blocks on the SuperH architecture.
However, some hardware blocks must be accessed through P4. Converting
the P4 address to a physical and then back to a P2 does not work. One
example of this is the sh7722 TMU block, it must be accessed through P4.
Without this patch P4 addresses will be mapped using PTEs which
requires the page allocator to be up and running.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Nov 2008 08:33:48 +0000 (17:33 +0900)]
sh: Migrate necessary libgcc bits in to arch/sh/lib for SUPERH32.
This moves in the necessary libgcc bits for SUPERH32 and drops the
libgcc linking for the regular targets. This in turn allows us to rip
out quite a few hacks both in sh_ksyms_32 and arch/sh/Makefile.
Paul Mundt [Tue, 18 Nov 2008 05:21:34 +0000 (14:21 +0900)]
sh: Fix clock framework compiler warnings.
CC arch/sh/kernel/cpu/clock.o
arch/sh/kernel/cpu/clock.c: In function 'clk_disable':
arch/sh/kernel/cpu/clock.c:156: warning: 'return' with a value, in function returning void
Introduced by ("sh: enable and disable clocks recursively").
Paul Mundt [Tue, 18 Nov 2008 03:40:39 +0000 (12:40 +0900)]
usb: Fix up sh_mobile usbf clock framework warnings.
drivers/usb/gadget/m66592-udc.c: In function 'm66592_probe':
drivers/usb/gadget/m66592-udc.c:1672: warning: label 'clean_up2' defined but not used
drivers/usb/host/r8a66597-hcd.c: In function 'r8a66597_probe':
drivers/usb/host/r8a66597-hcd.c:2401: warning: label 'clean_up2' defined but not used
Thomas Gleixner [Sat, 20 Dec 2008 20:27:34 +0000 (21:27 +0100)]
Null pointer deref with hrtimer_try_to_cancel()
Impact: Prevent kernel crash with posix timer clockid CLOCK_MONOTONIC_RAW
commit 2d42244ae71d6c7b0884b5664cf2eda30fb2ae68 (clocksource:
introduce CLOCK_MONOTONIC_RAW) introduced a new clockid, which is only
available to read out the raw not NTP adjusted system time.
The above commit did not prevent that a posix timer can be created
with that clockid. The timer_create() syscall succeeds and initializes
the timer to a non existing hrtimer base. When the timer is deleted
either by timer_delete() or by the exit() cleanup the kernel crashes.
Prevent the creation of timers for CLOCK_MONOTONIC_RAW by setting the
posix clock function to no_timer_create which returns an error code.
Reported-and-tested-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 20 Dec 2008 19:07:31 +0000 (11:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: change simple_strtol to simple_strtoul
9p: convert d_iname references to d_name.name
9p: Remove potentially bad parameter from function entry debug print.
Linus Torvalds [Sat, 20 Dec 2008 19:07:18 +0000 (11:07 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix resume (S2R) broken by Intel microcode module, on A110L
x86 gart: don't complain if no AMD GART found
AMD IOMMU: panic if completion wait loop fails
AMD IOMMU: set cmd buffer pointers to zero manually
x86: re-enable MCE on secondary CPUS after suspend/resume
AMD IOMMU: allocate rlookup_table with __GFP_ZERO
might hang upon resuming, OTOH it should have likely hanged each and every time.
(1) possible deadlock in microcode_resume_cpu() if either 'if' section is
taken;
(2) now, I don't see it in spec. and can't experimentally verify it (newer
ucodes don't seem to be available for my Core2duo)... but logically-wise, I'd
think that when read upon resuming, the 'microcode revision' (MSR 0x8B) should
be back to its original one (we need to reload ucode anyway so it doesn't seem
logical if a cpu doesn't drop the version)... if so, the comparison with
memcmp() for the full 'struct cpu_signature' is wrong... and that's how one of
the aforementioned 'if' sections might have been triggered - leading to a
deadlock.
Obviously, in my tests I simulated loading/resuming with the ucode of the same
version (just to see that the file is loaded/re-loaded upon resuming) so this
issue has never popped up.
I'd appreciate if someone with an appropriate system might give a try to the
2nd patch (titled "fix a comparison && deadlock...").
In any case, the deadlock situation is a must-have fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt fusion: clear list of outstanding commands on host reset
[SCSI] scsi_lib: only call scsi_unprep_request() under queue lock
[SCSI] ibmvstgt: move crq_queue_create to the end of initialization
[SCSI] libiscsi REGRESSION: fix passthrough support with older iscsi tools
[SCSI] aacraid: disable Dell Percraid quirk on Adaptec 2200S and 2120S
Linus Torvalds [Fri, 19 Dec 2008 19:36:04 +0000 (11:36 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: GEM on PAE has problems - disable it for now.
drm/i915: Don't return busy for buffers left on the flushing list.
Stanley Miao [Fri, 19 Dec 2008 14:08:22 +0000 (22:08 +0800)]
ALSA: Fix a Oops bug in omap soc driver.
There will be a Oops or frequent underrun messages when playing music with
omap soc driver, this is because a data region is incorretly sized, other data
region will be overwriten when writing to this data region.
Signed-off-by: Stanley Miao <stanley.miao@windriver.com> Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com> Cc: stable@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 19 Dec 2008 13:02:32 +0000 (14:02 +0100)]
ALSA: hda - Remove non-working headphone control for Dell laptops
The previous commit re-enabled hp_nid setup for IDT92HD73*, but
it's unneeded indeed for Dell laptops that have multiple headphones.
Setting the extra hp_nid results in a non-working "Headpohne" mixer
control. Thus hp_nid should be 0 for these dell models.
Also, the automatic addition of hp_nid should check whether it's
a dual-HP model or not. For dual-HPs, the pins are already checked
by the early workaround.
Takashi Iwai [Wed, 17 Dec 2008 13:51:01 +0000 (14:51 +0100)]
ALSA: hda - Add no-jd model for IDT 92HD73xx
Added the model without the jack-detection for some desktops that
have really no jack-detection. The recent driver caused regressions
regarding the sound output on such machines.
cciss: fix problem that deleting multiple logical drives could cause a panic
Fix problem that deleting multiple logical drives could cause a panic.
It fixes a panic which can be easily reproduced in the following way: Just
create several "arrays," each with multiple logical drives via hpacucli,
then delete the first array, and it will blow up in deregister_disk(), in
the call to get_host() when it tries to dig the hba pointer out of a NULL
queue pointer.
The problem has been present since my code to make rebuild_lun_table
behave better went in.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Dave Airlie [Fri, 19 Dec 2008 05:38:34 +0000 (15:38 +1000)]
drm/i915: GEM on PAE has problems - disable it for now.
On PAE systems, GEM allocates pages using shmem, and passes these
pages to be bound into AGP, however the AGP interfaces + the x86
set_memory interfaces all take unsigned long not dma_addr_t.
The initial fix for this was a mess, so we need to do this correctly
for 2.6.29.
Eric Anholt [Mon, 15 Dec 2008 03:05:04 +0000 (19:05 -0800)]
drm/i915: Don't return busy for buffers left on the flushing list.
These buffers don't have active rendering still occurring to them, they just
need either a flush to be emitted or a retire_requests to occur so that we
notice they're done. Return unbusy so that one of the two occurs. The two
expected consumers of this interface (OpenGL and libdrm_intel BO cache) both
want this behavior.
Signed-off-by: Eric Anholt <eric@anholt.net> Acked-by: Keith Packard <keithp@keithp.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
NeilBrown [Fri, 19 Dec 2008 05:25:01 +0000 (16:25 +1100)]
md: Don't read past end of bitmap when reading bitmap.
When we read the write-intent-bitmap off the device, we currently
read a whole number of pages.
When PAGE_SIZE is 4K, this works due to the alignment we enforce
on the superblock and bitmap.
When PAGE_SIZE is 64K, this case read past the end-of-device
which causes an error.
When we write the superblock, we ensure to clip the last page
to just be the required size. Copy that code into the read path
to just read the required number of sectors.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: stable@kernel.org
John McCutchan [Thu, 18 Dec 2008 01:43:02 +0000 (17:43 -0800)]
Maintainer email fixes for inotify
Update John McCutchan and Robert Love's email addresses for
maintenance of inotify
Signed-off-by: John McCutchan <john@johnmccutchan.com> Acked-by: Robert Love <rlove@rlove.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bjorn Helgaas [Wed, 17 Dec 2008 19:52:34 +0000 (12:52 -0700)]
x86 gart: don't complain if no AMD GART found
Impact: remove annoying bootup printk
It's perfectly normal for no AMD GART to be present, e.g., if you have
Intel CPUs. None of the other iommu_init() functions makes noise when
it finds nothing.
Takashi Iwai [Wed, 17 Dec 2008 12:48:29 +0000 (13:48 +0100)]
ALSA: hda - Fix silent HP output on D975
Some desktops seems to have no HP/mic jack detection on the front panel,
which results in the silent output in the recent driver, because the
driver mutes the output (to save power) when no plug is detected.
This patch adds a new model that disables the jack-detection.
I happened to notice that the ibmphp hotplug driver does something
rather silly in its init routine. It purposely calls module_put so as
to underflow its module ref count to avoid being removed from the
kernel. This is bad practice, and wrong, since it provides a window for
subsequent module_gets to reset the refcount to zero, allowing an unload
to race in and cause all sorts of mysterious panics. If the module is
unsafe to load, simply omitting the module_exit parameter is sufficient
to prevent the kernel from allowing the unload.
Samuel Ortiz [Wed, 17 Dec 2008 23:44:58 +0000 (15:44 -0800)]
irda: Add irda_skb_cb qdisc related padding
We need to pad irda_skb_cb in order to keep it safe accross dev_queue_xmit()
calls. This is some ugly and temporary hack triggered by recent qisc code
changes.
Even though it fixes bugzilla.kernel.org bug #11795, it will be replaced by a
proper fix before 2.6.29 is released.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 17 Dec 2008 23:05:26 +0000 (15:05 -0800)]
Merge branch 'i2c-fixes' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fixes' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-s3c2410: fix check for being in suspend.
i2c-cpm: Detect and report NAK right away instead of timing out
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: pl2303: add id for Hewlett-Packard LD220-HP POS pole display
USB: set correct configuration in probe of ti_usb_3410_5052
USB: add 5372:2303 to pl2303
USB: skip Set-Interface(0) if already in altsetting 0
USB: fix comment about endianness of descriptors
USB: Documentation/usb/gadget_serial.txt: update to match driver use_acm behaviour
usbmon: drop bogus 0t from usbmon.txt
USB: gadget: fix rndis working at high speed
USB: ftdi_sio: Adding Ewert Energy System's CANdapter PID
USB: tty: SprogII DCC controller identifiers
usb-storage: update unusual_devs entry for Nokia 5310
USB: Unusual devs patch for Nokia 3500c
USB: storage: unusual_devs.h: Nokia 3109c addition
USB: fix problem with usbtmc driver not loading properly
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
STAGING: Move staging drivers back to staging-specific menu
driver core: add newlines to debugging enabled/disabled messages
xilinx_hwicap: remove improper wording in license statement
driver core: fix using 'ret' variable in unregister_dynamic_debug_module
Jeff Layton [Wed, 17 Dec 2008 11:31:53 +0000 (06:31 -0500)]
cifs: fix buffer overrun in parse_DFS_referrals
While testing a kernel with memory poisoning enabled, I saw some warnings
about the redzone getting clobbered when chasing DFS referrals. The
buffer allocation for the unicode converted version of the searchName is
too small and needs to take null termination into account.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Acked-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 17 Dec 2008 22:58:56 +0000 (14:58 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc:
powerpc: Fix corruption error in rh_alloc_fixed()
powerpc/fsl-booke: Fix the miss interrupt restore
driver core: fix using 'ret' variable in unregister_dynamic_debug_module
The 'ret' variable is assigned, but not used in the return statement. Fix this.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Arnold [Sat, 13 Dec 2008 11:42:53 +0000 (22:42 +1100)]
USB: add 5372:2303 to pl2303
This patch adds the "Superial" USB-Serial converter to pl2303 so that it
is detected, by the correct driver. Adds the relevant vendor:product
(5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has
been tested against 2.6.24-22-generic.
Signed-off-by: Matthew D Arnold <matthew.arnold-1@uts.edu.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 1 Dec 2008 15:24:41 +0000 (10:24 -0500)]
USB: skip Set-Interface(0) if already in altsetting 0
When a driver unbinds from an interface, usbcore always sends a
Set-Interface request to reinstall altsetting 0. Unforunately, quite
a few devices have buggy firmware that crashes when it receives this
request.
To avoid such problems, this patch (as1180) arranges to send the
Set-Interface request only when the interface is not already in
altsetting 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Endecott [Mon, 1 Dec 2008 15:22:33 +0000 (10:22 -0500)]
USB: fix comment about endianness of descriptors
This patch fixes a comment and clarifies the documentation about the
endianness of descriptors. The current policy is that descriptors will
be little-endian at the API even on big-endian systems; however the
/proc/bus/usb API predates this policy and presents descriptors with
some multibyte fields byte-swapped.
Signed-off-by: Phil Endecott <usb_endian_patch@chezphil.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Korsgaard [Thu, 4 Dec 2008 15:30:53 +0000 (16:30 +0100)]
USB: Documentation/usb/gadget_serial.txt: update to match driver use_acm behaviour
Commit 7bb5ea54 (usb gadget serial: use composite gadget framework)
changed the default for the use_acm parameter from 0 to 1.
Update the documentation to match.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 25 Nov 2008 07:11:03 +0000 (23:11 -0800)]
USB: gadget: fix rndis working at high speed
Fix a bug specific to highspeed mode in the recently updated RNDIS
support: it wasn't setting up the high speed notification endpoint,
which prevented high speed RNDIS links from working.
projects / linux-2.6-omap-h63xx.git / log