mv643xx_eth: detect alternate TX BW control register location
Some SoCs have the TX bandwidth control registers in a slightly
different place. This patch detects that case at run time, and
re-directs accesses to those registers to the proper place at
run time if needed.
mv643xx_eth: detect extended rx coal register field
Newer hardware has a 16-bit instead of a 14-bit RX coalescing
count field in the SDMA_CONFIG register. This patch adds a run-time
check for which of the two we have, and adjusts further writes to the
rx coal count field accordingly.
Under some conditions, the TXQ ('TX queue being served') bit can clear
before all packets queued for that TX queue have been transmitted.
This patch enables TXend interrupts, and uses those to re-kick TX
queues that claim to be idle but still have queued descriptors from
the interrupt handler.
As with the multiple RX queue support, allow the platform code to
specify that the hardware we are running on supports multiple TX
queues. This patch only uses the highest-numbered enabled queue
to send packets to for now, this can be extended later to enable
QoS and such.
Allow the platform code to specify that we are running on hardware
that is capable of supporting multiple RX queues. If this option
is used, initialise all of the given RX queues instead of just RX
queue zero.
Add an interface for the hardware's per-port and per-subqueue
TX rate control. In this stage, this is mainly so that we can
disable the bandwidth limits during initialisation of the port.
General cleanup of the mv643xx_eth driver. Mainly fixes coding
style / indentation issues, get rid of some useless 'volatile's,
kill some more superfluous comments, and such.
Remove the write-only ->[rt]x_int_coal members from struct
mv643xx_eth_private. In the process, tweak the RX/TX interrupt
mitigation code so that it is compiled by default, and set the
default coalescing delays to 0 usec.
mv643xx_eth: kill private unused instance of struct net_device_stats
The per-port mv643xx_eth_private struct had a private instance
of struct net_device_stats that was never ever written to, only
read (via the ethtool statistics interface). This patch gets
rid of the private instance, and tweaks the ethtool statistics
code in mv643xx_eth to use the statistics in struct net_device
instead.
Since they are no longer used, kill enum FUNC_RET_STATUS and
struct pkt_info (which were a rather roundabout way of communicating
RX/TX status within the same driver).
mv643xx_eth: move rx_return_buff() into its only caller
rx_return_buff() is also a remnant of the HAL layering that the
original mv643xx_eth driver used. Moving it into its caller kills
the last reference to FUNC_RET_STATUS/pkt_info.
mv643xx_eth: move port_receive() into its only caller
The port_receive() function is a remnant of the original mv643xx_eth
HAL split. This patch moves port_receive() into its caller, so that
the top and the bottom half of RX processing no longer communicate
via the HAL FUNC_RET_STATUS/pkt_info mechanism abstraction anymore.
Half of the functions in the mv643xx_eth driver are prefixed by
useless and baroque comment blocks on _what_ those functions do (which
is obvious from the code itself) rather than why, and there's no point
in keeping those comments around.
mv643xx_eth: use 'mv643xx_eth_' prefix consistently
A bunch of places in the mv643xx_eth driver use the 'mv643xx_'
prefix. Since the mv643xx is a chip that includes more than just
ethernet, this patch makes all those places use either no prefix
(for some internal-use-only functions), or the full 'mv643xx_eth_'
prefix.
mv643xx_eth: get rid of ETH_/ethernet_/eth_ prefixes
The fact that mv643xx_eth is an ethernet driver is pretty obvious,
and having a lot of internal-use-only functions and defines prefixed
with ETH_/ethernet_/eth_ prefixes is rather pointless. So, get rid
of most of those prefixes.
mv643xx_eth: move MIB offset defines into their only user
The only user of the ETH_MIB_VERY_LONG_NAME_HERE defines is the
eth_update_mib_counters() function. Get rid of the defines by
open-coding the register offsets in the latter.
Replace the nondescriptive names ETH_INT_UNMASK_ALL and
ETH_INT_UNMASK_ALL_EXT by names of the actual fields being masked
and unmasked in the various writes to the interrupt mask registers.
mv643xx_eth: delete unused port serial control register bit defines
Over half of the port serial control register bit defines are never
used, and the PORT_SERIAL_CONTROL_DEFAULT_VALUE define is never used
either. Keep only those defines that are actually used.
mv643xx_eth: get rid of individual port config extend register bit defines
The port config extend register is never changed at run time.
Document the meaning of the initial value, and delete the defines
for the individual bits in this register.
mv643xx_eth: get rid of individual port config register bit defines
The mv643xx_eth driver only ever changes bit 0 of the port config
register at run time, the rest of the register bits are fixed (and
always zero). Document the meaning of the chosen default value,
and get rid of all the defines for each of the individual bits.
mv643xx_eth: reverse topological sort of functions
This patch performs a reverse topological sort of all functions in
mv643xx_eth.c, so that we can get rid of all forward declarations,
and end up with a more understandable driver due to related functions
being grouped together.
Harvey Harrison [Tue, 10 Jun 2008 19:48:45 +0000 (12:48 -0700)]
bluetooth: hci_bcsp.c small cleanups/api users
Use bitrev16 from lib/bitrev.c.
Use the get_unaligned_be16 to get the crc from the packet, create a
small helper function for this.
Fix a shadowed variable sparse warning:
drivers/bluetooth/hci_bcsp.c:218:26: warning: symbol 'hdr' shadows an earlier one
drivers/bluetooth/hci_bcsp.c:187:5: originally declared here
[akpm@linux-foundation.org: select CONFIG_BITREVERSE, noted by akinobu.mita@gmail.com] Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- No need to perform data_len = 0 in the switch command, since data_len
is initialized to 0 in the beginning of the ipq_build_packet_message()
method.
- {ip,ip6}_queue: We can reach nlmsg_failure only from one place; skb is
sure to be NULL when getting there; since skb is NULL, there is no need
to check this fact and call kfree_skb().
Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Rami Rosen [Mon, 9 Jun 2008 23:00:22 +0000 (16:00 -0700)]
netfilter: nf_conntrack: remove unnecessary function declaration
This patch removes nf_ct_ipv4_ct_gather_frags() method declaration from
include/net/netfilter/ipv4/nf_conntrack_ipv4.h, since it is unused in
the Linux kernel.
Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: ctnetlink: include conntrack status in destroy event message
When a conntrack is destroyed, the connection status does not get
exported to netlink. I don't see a reason for not doing so. This patch
exports the status on all conntrack events.
Signed-off-by: Fabian Hugelshofer <hugelshofer2006@gmx.ch> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the last packet of a connection isn't accounted when its causing
abnormal termination.
Introduces nf_ct_kill_acct() which increments the accounting counters on
conntrack kill. The new function was necessary, because there are calls
to nf_ct_kill() which don't need accounting:
nf_conntrack_proto_tcp.c line ~847:
Kills ct and returns NF_REPEAT. We don't want to count twice.
nf_conntrack_proto_tcp.c line ~880:
Kills ct and returns NF_DROP. I think we don't want to count dropped
packets.
nf_conntrack_netlink.c line ~824:
As far as I can see ctnetlink_del_conntrack() is used to destroy a
conntrack on behalf of the user. There is an sk_buff, but I don't think
this is an actual packet. Incrementing counters here is therefore not
desired.
Signed-off-by: Fabian Hugelshofer <hugelshofer2006@gmx.ch> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Pekka Enberg [Mon, 9 Jun 2008 22:58:39 +0000 (15:58 -0700)]
netfilter: nf_conntrack_extend: use krealloc() in nf_conntrack_extend.c V2
The ksize() API is going away because it is being abused and it doesn't even
work consistenly across different allocators. Therefore, convert
net/netfilter/nf_conntrack_extend.c to use krealloc().
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
James Morris [Mon, 9 Jun 2008 22:57:24 +0000 (15:57 -0700)]
netfilter: ip_tables: add iptables security table for mandatory access control rules
The following patch implements a new "security" table for iptables, so
that MAC (SELinux etc.) networking rules can be managed separately to
standard DAC rules.
This is to help with distro integration of the new secmark-based
network controls, per various previous discussions.
The need for a separate table arises from the fact that existing tools
and usage of iptables will likely clash with centralized MAC policy
management.
The SECMARK and CONNSECMARK targets will still be valid in the mangle
table to prevent breakage of existing users.
Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: ctnetlink: add full support for SCTP to ctnetlink
This patch adds full support for SCTP to ctnetlink. This includes three
new attributes: state, original vtag and reply vtag.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: ctnetlink: group errors into logical errno sets
This patch groups ctnetlink errors into three logical sets:
* Malformed messages: if ctnetlink receives a message without some mandatory
attribute, then it returns EINVAL.
* Unsupported operations: if userspace tries to perform an unsupported
operation, then it returns EOPNOTSUPP.
* Unchangeable: if userspace tries to change some attribute of the
conntrack object that can only be set once, then it returns EBUSY.
This patch reduces the number of -EINVAL from 23 to 14 and it results in
5 -EBUSY and 6 -EOPNOTSUPP.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Kuo-lang Tseng [Mon, 9 Jun 2008 22:55:45 +0000 (15:55 -0700)]
netfilter: ebtables: add IPv6 support
It implements matching functions for IPv6 address & traffic class
(merged from the patch sent by Jan Engelhardt [jengelh@computergmbh.de]
http://marc.info/?l=netfilter-devel&m=120182168424052&w=2), protocol,
and layer-4 port id. Corresponding watcher logging function is also
added for IPv6.
Signed-off-by: Kuo-lang Tseng <kuo-lang.tseng@intel.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 9 Jun 2008 22:51:03 +0000 (15:51 -0700)]
af_iucv: exploit target message class support of IUCV
The first 4 bytes of data to be sent are stored additionally into
the message class field of the send request. A receiving target
program (not an af_iucv socket program) can make use of this
information to pre-screen incoming messages.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Mon, 9 Jun 2008 22:50:30 +0000 (15:50 -0700)]
iucv: prevent cpu hotplug when walking cpu_online_map.
The code used preempt_disable() to prevent cpu hotplug, however that
doesn't protect for cpus being added. So use get_online_cpus() instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Mon, 9 Jun 2008 22:49:57 +0000 (15:49 -0700)]
iucv: fix section mismatch warning.
WARNING: net/iucv/built-in.o(.exit.text+0x9c): Section mismatch in
reference from the function iucv_exit() to the variable
.cpuinit.data:iucv_cpu_notifier
This warning is caused by a reference from unregister_hotcpu_notifier()
from an exit function to a cpuinitdata annotated data structurre.
This is a false positive warning since for the non CPU_HOTPLUG case
unregister_hotcpu_notifier() is a nop.
Use __refdata instead of __cpuinitdata to get rid of the warning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo Molnar [Mon, 9 Jun 2008 22:47:38 +0000 (15:47 -0700)]
irda: net/irda build fix: mcs7780
-tip testing found the following build error:
drivers/built-in.o: In function `mcs_receive_irq':
mcs7780.c:(.text+0x4e429): undefined reference to `crc32_le'
drivers/built-in.o: In function `mcs_hard_xmit':
mcs7780.c:(.text+0x4e9af): undefined reference to `crc32_le'
Matt Carlson [Mon, 9 Jun 2008 22:41:33 +0000 (15:41 -0700)]
tg3: Update version to 3.92.1
This patch increments the version to 3.92.1.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 9 Jun 2008 22:41:12 +0000 (15:41 -0700)]
tg3: Fix 5761 WOL
On 5761 non-e devices, two problems prevent the administrator from
overriding the WOL settings in the device's NVRAM.
The first problem is that GPIO 0 and GPIO 2 have been swapped. This
change prevented the administrator from turning on WOL when it is
disabled in NVRAM. The fix is to add a new path for the 5761 that
swaps the two GPIOs in the code as well.
The second problem is that GPIO 1 could not be toggled by the driver
because the GPIO is shared with the debug UART GPIO. This will prevent
the administrator from being able to turn WOL off if it was enabled in
NVRAM. The fix is to always disable the debug UART after a GRC reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 9 Jun 2008 22:40:26 +0000 (15:40 -0700)]
tg3: Fix a flags typo
This patch fixes a problem where the TG3_FLAG_10_100_ONLY flag was
testing against the wrong flags variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 9 Jun 2008 22:39:55 +0000 (15:39 -0700)]
tg3: Fix 5714S / 5715S / 5780S link failures
The git commit ef167e27039eeaea6d3cdd5c547b082e89840bdd entitled
"Fix supporting flowctrl code" introduced a bug that prevents 5714S,
5715S and 5780S devices from falling back to a forced link mode. The
problem is that the added flow control check will always fail if flow
control is set to autoneg and either RX or TX (or both) flow control
is enabled. The driver defaults to setting flow control to autoneg
and advertises both RX and TX flow control.
The fix is to remove the errant check.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Slusarz [Sun, 8 Jun 2008 11:13:06 +0000 (13:13 +0200)]
iwlwifi: fix oops in iwl3945_led_brightness_set
fix race between:
ieee80211_open->ieee80211_led_radio->led_trigger_event->led_set_brightness->iwl3945_led_brightness_set
(which assumes that "led->priv" is not NULL)
and
iwl3945_pci_probe->iwl3945_setup_deferred_work->(...)->iwl3945_bg_alive_start->iwl3945_alive_start->iwl3945_led_register->iwl3945_led_register_led
which sets priv field in struct iwl3945_led
after
led->led_dev.brightness_set = iwl3945_led_brightness_set;
(...)
led_classdev_register(device, &led->led_dev);
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: Zhu Yi <yi.zhu@intel.com> Cc: Reinette Chatre <reinette.chatre@intel.com> Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: linux-wireless@vger.kernel.org Cc: ipw3945-devel@lists.sourceforge.net Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Thu, 5 Jun 2008 18:29:49 +0000 (21:29 +0300)]
include/linux/ssb/ssb_driver_gige.h typo fix
This patch fixes a typo in the name of a config variable.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Adrian Bunk <bunk@kernel.org> Reviewed-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Thu, 5 Jun 2008 16:55:21 +0000 (19:55 +0300)]
mac80211: Checking IBSS support while changing channel in ad-hoc mode
This patch adds a check to the set_channel flow. When attempting to change
the channel while in IBSS mode, and the new channel does not support IBSS
mode, the flow return with an error value with no consequences on the
mac80211 and driver state.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Wed, 4 Jun 2008 17:59:34 +0000 (13:59 -0400)]
mac80211: decrease IBSS creation latency
Sufficient scans (at least 2 or 3) should have been done within 7
seconds to find an existing IBSS to join. This should improve IBSS
creation latency; and since IBSS merging is still in effect, shouldn't
have detrimental effects on eventual IBSS convergence.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Thu, 5 Jun 2008 14:55:10 +0000 (16:55 +0200)]
zd1211rw: Fix data padding for QoS
This patch fixes a data alignment issue in the zd1211rw driver.
The IEEE80211_STYPE_QOS_DATA bit should be used as a bitwise test
to test for the presence of the 2 byte QoS control field.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Note:
In general disconnection is still not handled properly in mac80211
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 4 Jun 2008 09:10:40 +0000 (11:10 +0200)]
libertas: fix sleep confirmation
This fixes an issus that made "iwconfig eth1 power on" non-working.
When we get a "PS sleep" event, we have to confirm this to the firmware.
The confirm happens with a command, but this command is special: the
firmware won't send us a response. if_cs_host_to_card() is setting
priv->dnld_sent anyway, so this variable stayed at DNLD_DATA_SENT and
was never cleared back.
Now I put the special knowledge that the CMD_802_11_PS_MODE with
CMD_SUBCMD_SLEEP_CONFIRMED doesn't need to need a response by directly
clearing the dnld_sent state in lbs_send_confirmsleep().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Mon, 2 Jun 2008 21:51:23 +0000 (17:51 -0400)]
ipw2200: queue direct scans
When another scan is in progress, a direct scan gets dropped on the
floor. However, that direct scan is usually the scan that's really
needed by userspace, and gets stomped on by all the broadcast scans the
ipw2200 driver issues internally. Make sure the direct scan happens
eventually, and as a bonus ensure that the passive scan worker is
cleaned up when appropriate.
The change of request_passive_scan form a struct work to struct
delayed_work is only to make the set_wx_scan() code a bit simpler, it's
still only used with a delay of 0 to match previous behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch defines a few new message header manipulation routines,
and generalizes the usefulness of another, in preparation for upcoming
rework of TIPC's message rejection code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:47:30 +0000 (17:47 -0700)]
tipc: Expand link sequence gap field to 13 bits
This patch increases the "sequence gap" field of the LINK_PROTOCOL
message header from 8 bits to 13 bits (utilizing 5 previously
unused 0 bits). This ensures that the field is big enough to
indicate the loss of up to 8191 consecutive messages on the link,
thereby accommodating the current worst-case scenario of 4000
lost messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:38:22 +0000 (17:38 -0700)]
tipc: Add missing spinlock in name table display code
This patch ensures that the display code that traverses the
publication lists belonging to a name table entry take its
associated spinlock, to protect against a possible change to
one of its "head of list" pointers caused by a simultaneous
name table lookup operation by another thread of control.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:37:59 +0000 (17:37 -0700)]
tipc: Prevent display of name table types with no publications
This patch adds a check to prevent TIPC's name table display code
from listing a name type entry if it exists only to hold subscription
info, rather than published names.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:37:34 +0000 (17:37 -0700)]
tipc: Optimize message initialization routine
This patch eliminates the rarely-used "error code" argument
when initializing a TIPC message header, since the default
value of zero is the desired result in most cases; the few
exceptional cases now set the error code explicitly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:36:58 +0000 (17:36 -0700)]
tipc: Prevent access of non-existent field in short message header
This patch eliminates a case where TIPC's link code could try reading
a field that is not present in a short message header. (The random
value obtained was not being used, but the read operation could result
in an invalid memory access exception in extremely rare circumstances.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:32:35 +0000 (17:32 -0700)]
tipc: Minor optimizations to received message processing
This patch enhances TIPC's handler for incoming messages in two
ways:
- the trivial, single-use routine for processing non-sequenced
messages has been merged into the main handler
- the interface that received a message is now identified without
having to access and/or modify the associated sk_buff
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:29:39 +0000 (17:29 -0700)]
tipc: Fix minor bugs in link session number handling
This patch introduces a new, out-of-range value to indicate that
a link endpoint does not have an existing session established
with its peer, eliminating the risk that the previously used
"invalid session number" value (i.e. zero) might eventually be
assigned as a valid session number and cause incorrect link
behavior.
The patch also introduces explicit bit masking when assigning a
new link session number to ensure it does not exceed 16 bits.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:29:09 +0000 (17:29 -0700)]
tipc: Fix bugs in message error code display when debugging
This patch corrects two problems in the display of error code
information in TIPC messages when debugging:
- no longer tries to display error code in NAME_DISTRIBUTOR
messages, which don't have the error field
- now displays error code in 24 byte data messages, which do
have the error field
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:28:45 +0000 (17:28 -0700)]
tipc: Standardize error checking on incoming messages via native API
This patch re-orders & re-groups the error checks performed on
messages being delivered to native API ports, in order to clarify the
similarities and differences required for the various message types.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 5 Jun 2008 00:28:21 +0000 (17:28 -0700)]
tipc: Fix bug in connection setup via native API
This patch fixes a bug that prevented TIPC from receiving a
connection setup request message on a native TIPC port.
The revised connection setup logic ensures that validation
of the source of a connection-based message is skipped if
the port is not yet connected to a peer.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Wed, 4 Jun 2008 22:54:07 +0000 (15:54 -0700)]
l2tp: Fix possible oops if transmitting or receiving when tunnel goes down
Some problems have been experienced in the field which cause an oops
in the pppol2tp driver if L2TP tunnels fail while passing data.
The pppol2tp driver uses private data that is referenced via the
sk->sk_user_data of its UDP and PPPoL2TP sockets. This patch makes
sure that the driver uses sock_hold() when it holds a reference to the
sk pointer. This affects its sendmsg(), recvmsg(), getname(),
[gs]etsockopt() and ioctl() handlers.
Tested by ISP where problem was seen. System has been up 10 days with
no oops since running this patch. Without the patch, an oops would
occur every 1-2 days.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: Fix for race due to temporary drop of the socket lock in skb_splice_bits.
skb_splice_bits temporary drops the socket lock while iterating over
the socket queue in order to break a reverse locking condition which
happens with sendfile. This, however, opens a window of opportunity
for tcp_collapse() to aggregate skbs and thus potentially free the
current skb used in skb_splice_bits and tcp_read_sock.
This patch fixes the problem by (re-)getting the same "logical skb"
after the lock has been temporary dropped.
Based on idea and initial patch from Evgeniy Polyakov.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Corked packet is allocated via sock_wmalloc which holds the owner socket,
so one should uncork it and flush all pending data on close. Do this in the
same way as in UDP.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Wed, 4 Jun 2008 22:07:32 +0000 (15:07 -0700)]
lt2p: Fix possible WARN_ON from socket code when UDP socket is closed
If an L2TP daemon closes a tunnel socket while packets are queued in
the tunnel's reorder queue, a kernel warning is logged because the
socket is closed while skbs are still referencing it. The fix is to
purge the queue in the socket's release handler.
Dan Williams [Thu, 29 May 2008 18:38:28 +0000 (14:38 -0400)]
ipw2200: expire and use oldest BSS on adhoc create
If there are no networks on the free list, expire the oldest one when
creating a new adhoc network. Because ipw2200 and the ieee80211 stack
don't actually cull old networks and place them back on the free list
unless they are needed for new probe responses, over time the free list
would become empty and creating an adhoc network would fail due to the !
list_empty(...) check.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrew Morton [Wed, 28 May 2008 19:40:39 +0000 (12:40 -0700)]
airo warning fix
WARNING: space prohibited between function name and open parenthesis '('
#22: FILE: drivers/net/wireless/airo.c:2907:
+ while ((IN4500 (ai, COMMAND) & COMMAND_BUSY) && (delay < 10000)) {
total: 0 errors, 1 warnings, 8 lines checked
./patches/wireless-airo-waitbusy-wont-delay.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Dan Williams <dcbw@redhat.com> Cc: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vlad Yasevich [Wed, 4 Jun 2008 19:40:15 +0000 (12:40 -0700)]
sctp: Fix ECN markings for IPv6
Commit e9df2e8fd8fbc95c57dbd1d33dada66c4627b44c ("[IPV6]: Use
appropriate sock tclass setting for routing lookup.") also changed the
way that ECN capable transports mark this capability in IPv6. As a
result, SCTP was not marking ECN capablity because the traffic class
was never set. This patch brings back the markings for IPv6 traffic.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log