Al Viro [Tue, 6 Sep 2005 06:35:41 +0000 (23:35 -0700)]
[SPARC64]: Kconfig fix (GEN_RTC dependencies)
Yet another architecture not coverd by GEN_RTC - sparc64 never picked
it until now and it doesn't have asm/rtc.h to go with it, so it
wouldn't compile anyway (or have these ioctls in the user-visible
headers, for that matter).
FWIW, I'm very tempted to introduce ARCH_HAS_GEN_RTC and have it set
in arch/*/Kconfig for architectures that know what to do with this
stuff - for something supposedly generic the list of architectures
where it doesn't work is getting too long...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Tue, 6 Sep 2005 06:30:15 +0000 (23:30 -0700)]
[MOXA]: Fix this driver properly.
Actually, proper fix of that breakage is embarrassingly simple - it's yet
another gratitious leftover include of asm/segment.h, so incremental to the
previos would be removal of that BROKEN and removal of bogus include from
mxser.c itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 6 Sep 2005 01:55:48 +0000 (18:55 -0700)]
[TCP]: Fix TCP_OFF() bug check introduced by previous change.
The TCP_OFF assignment at the bottom of that if block can indeed set
TCP_OFF without setting TCP_PAGE. Since there is not much to be
gained from avoiding this situation, we might as well just zap the
offset. The following patch should fix it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 6 Sep 2005 01:44:37 +0000 (18:44 -0700)]
[NET]: 2.6.13 breaks libpcap (and tcpdump)
Patrick McHardy says:
Never mind, I got it, we never fall through to the second switch
statement anymore. I think we could simply break when load_pointer
returns NULL. The switch statement will fall through to the default
case and return 0 for all cases but 0 > k >= SKF_AD_OFF.
Here's a patch to do just that.
I left BPF_MSH alone because it's really a hack to calculate the IP
header length, which makes no sense when applied to the special data.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 6 Sep 2005 00:53:32 +0000 (17:53 -0700)]
[TG3]: Use status tag to check for new events
Use the status tag to determine if there are new events in
tg3_interrupt_tagged(). We discussed about this a while ago with Grant
Grundler and DaveM. This scheme makes it unnecessary to clear the
updated bit in the status block when using tagged mode, and only
a simple comparison is needed to determine if there are new events.
The tp->lock around netif_rx_complete() and tg3_restart_ints() is also
removed. It is unnecessary with DaveM's new locking scheme.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 6 Sep 2005 00:53:19 +0000 (17:53 -0700)]
[TG3]: Remove status block access in tg3_msi() and add prefetches
Remove unnecessary status block accesses in tg3_msi(). Since MSI is
not shared, it is unnecessary to read the status block to determine if
there are any new events in the MSI handler. It is also unnecessary to
clear the updated bit in the status block.
Since the poll list is per-cpu, tg3_poll() will be scheduled to run on
the same CPU that received the MSI. Prefetches for the status block
and the next rx descriptors are added in tg3_msi() to improve their
access times when tg3_poll() runs.
In the non-MSI irq handlers, we need to check the status block because
interrupts may be shared. Only prefetches for the next rx descriptors
are added.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Reinecke [Fri, 15 Jul 2005 08:09:25 +0000 (10:09 +0200)]
[PATCH] Floppy: Add cmos attribute to floppy driver
Currently only a device 'fdX' shows up in sysfs; the other possible
device for this drive (like fd0h1440 etc) must be guessed from there.
This patch corrects the floppy driver to create a platform device for
each floppy found; each platform device also has an attribute 'cmos'
which represents the cmos type for this drive. From this attribute the
other possible device types can be computed.
From: Hannes Reinecke <hare@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] Driver core: link device and all class devices derived from it.
Driver core: link device and all class devices derived from it.
To ease the task of locating class devices derived from a certain
device create symlinks from parent device to its class devices.
Change USB host class device name from usbX to usb_hostX to avoid
conflict when creating aforementioned links.
Tweaked by Greg to have the symlink be "class_name:class_device_name" in
order to prevent duplicate links.
Fix for manual binding of drivers to devices. Problem is if you pass in
a valid device id, but the driver refuses to bind. Infinite loop as
write() tries to resubmit the data it just sent.
Thanks to Michal Ostrowski <mostrows@watson.ibm.com> for pointing the
problem out.
Richard Purdie [Mon, 5 Sep 2005 19:49:54 +0000 (20:49 +0100)]
[ARM] 2882/1: pxa2xx_sharpsl: Update PCMCIA driver to support variety of new hardware
Patch from Richard Purdie
This patch updates the PCMCIA pxa2xx_sharpsl driver to support multiple scoop
devices by adding a scoop to pcmcia slot mapping structure. It adds platform
support for poodle, is known to work on spitz (which is dual slot) and
should also support collie with a minor amount of further work.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Mon, 5 Sep 2005 19:47:53 +0000 (20:47 +0100)]
[ARM] 2876/1: N30 - remove task to toggle USB D+ line
Patch from Ben Dooks
The n30 machine file is using a kernel thread to change the
state of the USB D+ pull-up resistor, which is not the proper
way to do this. Once the usb-gadget support for the 24xx is
merge, the proper access method will be added.
This patch also removes the problem of using HZ for the
msleep calls, from Nishanth Aravamudan.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jean Delvare [Sat, 3 Sep 2005 08:52:11 +0000 (10:52 +0200)]
[PATCH] I2C: Drop the I2C_ACK_TEST ioctl
Drop the I2C_ACK_TEST ioctl, which was commented out. It never really
existed (not after 1999 anyway), and there is no such thing as a ack
test on I2C/SMBus anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jim Cromie [Fri, 2 Sep 2005 20:57:52 +0000 (22:57 +0200)]
[PATCH] hwmon: (2/3) pc87360 driver update
pc87360: number-skew to init
The temp, therm, fan, pwm callbacks all have an offset skew in the code
which accommodates attribute numbering conventions under
/sys/bus/i2c/devices/9191-6620/ (ie they start at 1)
This patch moves that skew into the declaration, and out of the
functions (except for therm, where we simplify from 2 skews to 1). The
declarative skew is clearer, less error-prone, and more efficient.
The use of 11+offset-4 below reflects the fact that the sysfs numbering
of these units is 4, 5, 6, but they use internal VLM units 11, 12, 13 to
measure the thermistor voltages.
There's one remaining skew factor, in *_crit callbacks below, because
there are no critical thresholds for voltages 0-10, only for those
supporting the thermistors.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jim Cromie [Fri, 2 Sep 2005 20:52:43 +0000 (22:52 +0200)]
[PATCH] hwmon: (1/3) pc87360 driver update
Use the new "dynamic sysfs callbacks", as introduced recently by Yani
Ioannou, in pc87360.
Note that this change isn't indiscriminate. Only those attributes that
would benefit from having an index (i.e., those which are
macro-repeated) have been converted.
This significantly shrinks the size of the module:
before: 49235 drivers/hwmon/pc87360.ko
after: 32532 drivers/hwmon/pc87360.ko
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Mon, 29 Aug 2005 19:10:31 +0000 (21:10 +0200)]
[PATCH] I2C: Drop probe parameter of i2c-keywest
The i2c-keywest driver has a "probe" module parameter which enables bus
scanning at load time. This can be done in userspace with the i2cdetect
tool (part of the lm_sensors package) instead. What's more, i2cdetect
gives more control on the way the bus is scanned, and is safer
(i2c-keywest currently scans reserved addresses and doesn't properly
handle the famous 24RF08 corruption case.)
Thus, I would propose that this module parameter be simply dropped.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Thu, 25 Aug 2005 14:43:29 +0000 (16:43 +0200)]
[PATCH] I2C: Drop debug eeprom dump code in pcilynx
The pcilynx driver includes code to dump the contents of an i2c eeprom
for debugging purposes. The same can be done from userspace using the
i2cdump tool (part of the lm_sensors project) instead, in a more
efficient and flexible way.
Thus I would suggest that this functionality be simply dropped from the
pcilynx driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Mon, 15 Aug 2005 17:57:04 +0000 (19:57 +0200)]
[PATCH] I2C: Drop I2C_DEVNAME and i2c_clientname
I2C_DEVNAME and i2c_clientname were introduced in 2.5.68 [1] to help
media/video driver authors who wanted their code to be compatible with
both Linux 2.4 and 2.6. The cause of the incompatibility has gone since
[2], so I think we can get rid of them, as they tend to make the code
harder to read and longer to preprocess/compile for no more benefit.
I'd hope nobody seriously attempts to keep media/video driver compatible
across Linux trees anymore, BTW.
Jean Delvare [Thu, 11 Aug 2005 21:51:10 +0000 (23:51 +0200)]
[PATCH] I2C: Kill i2c_algorithm.id (6/7)
In theory, there should be no more users of I2C_ALGO_* at this point.
However, it happens that several drivers were using I2C_ALGO_* for
adapter ids, so we need to correct these before we can get rid of all
the I2C_ALGO_* definitions.
Note that this also fixes a bug in media/video/tvaudio.c:
/* don't attach on saa7146 based cards,
because dedicated drivers are used */
if ((adap->id & I2C_ALGO_SAA7146))
return 0;
This test was plain broken, as it would succeed for many more adapters
than just the saa7146: any those id would share at least one bit with
the saa7146 id. We are really lucky that the few other adapters we want
this driver to work with did not fulfill that condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Thu, 11 Aug 2005 21:41:56 +0000 (23:41 +0200)]
[PATCH] I2C: Kill i2c_algorithm.id (5/7)
Merge the algorithm id part (16 upper bits) of the i2c adapters ids
into the definition of the adapters ids directly. After that, we don't
need to OR both ids together for each i2c_adapter structure.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Thu, 11 Aug 2005 21:38:52 +0000 (23:38 +0200)]
[PATCH] I2C: Kill i2c_algorithm.id (3/7)
Don't rely on i2c_algorithm.id to alter the i2c adapter's id, use the
I2C_ALGO_* value directly instead, because i2c_algorithm will soon
have no id member no more.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Thu, 11 Aug 2005 21:36:49 +0000 (23:36 +0200)]
[PATCH] I2C: Kill i2c_algorithm.id (2/7)
Use the adapter id rather than the algorithm id to detect the i2c-isa
pseudo-adapter. This saves one level of dereferencing, and the
algorithm ids will soon be gone anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Thu, 11 Aug 2005 21:33:24 +0000 (23:33 +0200)]
[PATCH] I2C: Kill i2c_algorithm.name (1/7)
The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 24RF08 corruption would better be prevented at i2c-core level than
at chip driver level, for several reasons:
* The second quick write should happen as soon as possible after the
first one, so as to limit the risk that another command is issued on
the bus inbetween, causing the corruption.
* As a matter of fact, the protection code at driver level was reworked
at least three times already, which proves how hard it is to get it
right there, while it's straightforward at i2c-core level.
* It's easy to add a new driver that would need the protection, and
forget to add it. This did happen already.
* As additional probing addresses can be passed to most i2c chip drivers
as module parameters, virtually every i2c chip driver would need the
protection if we want to be really safe.
* Why duplicate code when we can easily avoid it?
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Tue, 9 Aug 2005 18:17:55 +0000 (20:17 +0200)]
[PATCH] I2C: Rewrite i2c_probe
i2c_probe was quite complex and slow, so I rewrote it in a more
efficient and hopefully clearer way.
Note that this slightly changes the way the module parameters are
handled. This shouldn't change anything for the most common cases
though.
For one thing, the function now respects the order of the parameters
for address probing. It used to always do lower addresses first. The
new approach gives the user more control.
For another, ignore addresses don't overrule probe addresses anymore.
This could have been restored the way it was at the cost of a few more
lines of code, but I don't think it's worth it. Both lists are given
as module parameters, so a user would be quite silly to specify the
same addresses in both lists. The normal addresses list is the only
one that isn't controlled by a module parameter, thus is the only one
the user may reasonably want to remove an address from.
Another significant change is the fact that i2c_probe() will no more
stop when a detection function returns -ENODEV. Just because a driver
found a chip it doesn't support isn't a valid reason to stop all
probings for this one driver. This closes the long standing lm_sensors
ticket #1807.
In terms of algorithmic complexity, the new code is way better. If
I is the ignore address count, P the probe address count, N the
normal address count and F the force address count, the old code
was doing 128 * (F + I + P + N) iterations max, while the new code
does F + P + ((I+1) * N) iterations max. For the most common case
where F, I and P are empty, this is down from 128 * N to N.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Mon, 1 Aug 2005 20:50:08 +0000 (22:50 +0200)]
[PATCH] hwmon: hwmon vs i2c, second round (10/11)
I see very little reason why vid_from_reg is inlined. It is not
exactly short, its parameters are seldom known in advance, and it is
never called in speed critical areas. Uninlining it should cause
little performance loss if any, and saves a signficant space as well
as compilation time.
As suggested by Alexey Dobriyan, I am leaving vid_to_reg inline for now,
as it is short and has a single user so far.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 31 Jul 2005 19:52:01 +0000 (21:52 +0200)]
[PATCH] hwmon: hwmon vs i2c, second round (07/11)
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 31 Jul 2005 19:49:03 +0000 (21:49 +0200)]
[PATCH] hwmon: hwmon vs i2c, second round (06/11)
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 31 Jul 2005 19:36:24 +0000 (21:36 +0200)]
[PATCH] hwmon: hwmon vs i2c, second round (03/11)
We now have two identical structures, i2c_address_data in i2c-sensor.h
and i2c_client_address_data in i2c.h. We can kill one of them, I choose
to keep the one in i2c.h as it makes more sense (this structure is not
specific to sensors.)
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 31 Jul 2005 19:33:23 +0000 (21:33 +0200)]
[PATCH] hwmon: hwmon vs i2c, second round (02/11)
The way i2c-sensor handles forced addresses could be optimized. It
defines a structure (i2c_force_data) to associate a module parameter
with a given kind value, but in fact this kind value is always the
index of the structure in each array it is used in. So this additional
value can be omitted, and still be deduced in the code handling these
arrays.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 31 Jul 2005 19:20:43 +0000 (21:20 +0200)]
[PATCH] hwmon: hwmon vs i2c, second round (01/11)
Add support for kind-forced addresses to i2c_probe, like i2c_detect
has for (essentially) hardware monitoring drivers.
Note that this change will slightly increase the size of the drivers
using I2C_CLIENT_INSMOD, with no immediate benefit. This is a
requirement if we want to merge i2c_probe and i2c_detect though, and
seems a reasonable price to pay in comparison with the previous
cleanups which saved much more than that (such as the i2c-isa cleanup
or the i2c address ranges removal.)
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Sun, 31 Jul 2005 17:02:53 +0000 (19:02 +0200)]
[PATCH] I2C: Improve core debugging messages
The debugging messages in i2c-core are more confusing than helpful. Some
lack their trailing newline, some lack a prefix, some are redundant,
some lack precious information. Here is my attempt to introduce some
standardization in there.
I also changed two messages in i2c-dev to make it clear they come from
i2c-dev.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ian Campbell [Wed, 10 Aug 2005 07:51:16 +0000 (08:51 +0100)]
[PATCH] I2C: i2c-algo-pca -- gracefully handle a busy bus
I've been running with this patch for a while now, and while I've never
seen it trigger except with buggy hardware I think it is a cleaner way
to handle a busy bus. I had -EBUSY until about 10 minutes ago but -EIO
seems to be what most of the existing algo drivers will return in the
same circumstances.
Signed-off-by: Ian Campbell <icampbell@arcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 27 Jul 2005 19:32:02 +0000 (21:32 +0200)]
[PATCH] hwmon: tag super-i/o find functions __init
Super-I/O find functions in hardware monitoring drivers can be tagged
__init as they are only called from functions themselves tagged __init.
Two of them (smsc47b397 and w83627ehf) already do, but the other four
of them (it87, pc87360, smsc47m1 and w83627hf) did not.
This saves a few bytes of memory after the drivers are loaded, 192 in
the case of the it87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 27 Jul 2005 20:14:49 +0000 (22:14 +0200)]
[PATCH] I2C: refactor message in i2c_detach_client
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to announce support for W83792D chip. This driver was developed
by Winbond Electronics Corp. I added sysfs attributes callbacks infrastructure
plus various code fixes and codingstyle cleanups. I would like to thank Winbond
for supporting free software.
This patch is against 2.6.13rc3 plus hwmon-class and hwmon-split.
Separate patch for documantation and hwmon class register will follow.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: Chunhao Huang <DZShen@Winbond.com.tw> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Tue, 19 Jul 2005 22:05:33 +0000 (00:05 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (8/9)
Kill all uses of i2c_is_isa_adapter except for the hybrid drivers (it87,
lm78, w83781d). The i2c-isa adapter not being registered with the i2c
core anymore, drivers don't have to fear being erroneously attached to
it.
Jean Delvare [Tue, 19 Jul 2005 22:02:32 +0000 (00:02 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (7/9)
Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.
normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Jean Delvare [Tue, 19 Jul 2005 21:57:54 +0000 (23:57 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (6/9)
Kill all isa-related stuff from i2c_detect, it's not used anymore.
This is one major step in the directiom of merging i2c_probe and
i2c_detect. The last obstacle I can think of is the different way forced
addresses work between sensors and non-sensors i2c drivers. I'll deal
with that in a later patchset.
Jean Delvare [Tue, 19 Jul 2005 21:56:35 +0000 (23:56 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (5/9)
Call the ISA chip drivers detection function directly instead of relying
on i2c_detect. The net effect is that address lists won't be handled
anymore, but they were mostly useless in the ISA case anyway (pc87360,
smsc47m1, smsc47b397 had already dropped them).
We don't need to handle multiple devices, all we may need is a way to
force a given address instead of the original one (some drivers already
do: sis5595, via686a, w83627hf), and, for drivers supporting multiple
chips, a way to force one given kind. All this may be added later on
demand, but I actually don't think there will be much demand.
Jean Delvare [Tue, 19 Jul 2005 21:53:07 +0000 (23:53 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (4/9)
All ISA hardware monitoring drivers (including hybrid drivers) now have
a hard dependency on i2c-isa, so they must select I2C_ISA. As a result,
CONFIG_I2C_ISA doesn't need to be left visible to the user. The good
thing here is that users will stop complaining that some driver doesn't
work just because they forgot to compile or load i2c-isa.
At this point, all drivers are working again and the cleanup phase can
begin.
Jean Delvare [Tue, 19 Jul 2005 21:51:07 +0000 (23:51 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (3/9)
Convert the 10 ISA hardware monitoring drivers (it87, lm78, pc87360,
sis5595, smsc47b397, smsc47m1, via686a, w83627hf, w83627ehf, w83781d) to
explicitely register with i2c-isa. For hybrid drivers (it87, lm78,
w83781d), we now have two separate instances of i2c_driver, one for the
I2C interface of the chip, and one for ISA interface. In the long run,
the one for ISA will be replaced with a different driver type.
At this point, all drivers are working again, except for missing
dependencies in Kconfig.
Jean Delvare [Tue, 19 Jul 2005 21:48:43 +0000 (23:48 +0200)]
[PATCH] I2C: Separate non-i2c hwmon drivers from i2c-core (2/9)
Convert i2c-isa from a dumb i2c_adapter into a pseudo i2c-core for ISA
hardware monitoring drivers. The isa i2c_adapter is no more registered
with i2c-core, drivers have to explicitely connect to it using the new
i2c_isa_{add,del}_driver interface.
At this point, all ISA chip drivers are useless, because they still
register with i2c-core in the hope i2c-isa is registered there as well,
but it isn't anymore.
The fake bus will be named i2c-9191 in sysfs. This is the number it
already had internally in various places, so it's not exactly new,
except that now the number is seen in userspace as well. This shouldn't
be a problem until someone really has 9192 I2C busses in a given system
;)
The fake bus will no more show in "i2cdetect -l", as it won't be seen by
i2c-dev anymore (not being registered with i2c-core), which is a good
thing, as i2cdetect/i2cdump/i2cset cannot operate on this fake bus
anyway.
Mark M. Hoffman [Sat, 16 Jul 2005 01:39:18 +0000 (21:39 -0400)]
[PATCH] I2C hwmon: add hwmon sysfs class to drivers
This patch modifies sensors chip drivers to make use of the new
sysfs class "hwmon".
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark M. Hoffman [Sat, 16 Jul 2005 01:38:08 +0000 (21:38 -0400)]
[PATCH] I2C hwmon: hwmon sysfs class
This patch adds the sysfs class "hwmon" for use by hardware monitoring
(sensors) chip drivers. It also fixes up the related Kconfig/Makefile
bits.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 27 Jul 2005 19:30:16 +0000 (21:30 +0200)]
[PATCH] hwmon: kill client name lm78-j
Drop the separate client name for the LM78-J chip. This is really
only a later revision of the LM78, with almost no difference and
no difference the driver handles in any case.
This was the only client name that had a dash in it, and special care
had to be taken in libsensors because of it. As we plan to write a new
library soon, I'd like to get rid of this exception before we do.
As a nice side effect, it saves 876 bytes in lm78.ko.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 27 Jul 2005 19:28:28 +0000 (21:28 +0200)]
[PATCH] hwmon: soften lm75 initialization
The LM75 initialization is a bit agressive, it arbitrarily reconfigures
the chip. Make it only change the bit it needs. This is a port from
the 2.4 kernel version of the driver (lm_sensors).
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6-omap-h63xx.git / log