Chuck Ebbert [Fri, 19 Aug 2005 12:14:07 +0000 (14:14 +0200)]
[WATCHDOG] softdog-timer-running-oops.patch
The softdog watchdog timer has a bug that can create an oops:
1. Load the module without the nowayout option.
2. Open the driver and close it without writing 'V' before close.
3. Unload the module. The timer will continue to run...
4. Oops happens when timer fires.
Reported Sun, 10 Oct 2004, by Michael Schierl <schierlm@gmx.de>
Fix is easy: always take a reference on the module on open.
Release it only when the device is closed and no timer is running.
Tested on 2.6.13-rc6 using the soft_noboot option. While the
timer is running and the device is closed, the module use count
stays at 1. After the timer fires, it drops to 0. Repeatedly
opening and closing the driver caused no problems. Please apply.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
P@Draig Brady [Wed, 17 Aug 2005 07:06:07 +0000 (09:06 +0200)]
[WATCHDOG] w83627hf_wdt.c-initialized_bios_bug
Attached is a small update to the w83627hf watchdog driver
to initialise appropriately if it was already initialised
in the BIOS. On tyan motherboards for e.g. you can init
the watchdog to 4 mins, then when the driver is loaded it
sets the watchdog to "seconds" mode, and then machine will
reboot within 4 seconds. So this patch resets the timeout
to the configured value if the watchdog is already running.
Signed-off-by: P@draig Brady <P@draigBrady.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Olaf Hering [Wed, 17 Aug 2005 06:58:34 +0000 (08:58 +0200)]
[WATCHDOG] correct sysfs name for watchdog devices
While looking for possible candidates for our udev.rules package,
I found a few odd ->name properties. /dev/watchdog has minor 130
according to devices.txt. Since all watchdog drivers use the
misc_register() call, they will end up in /sys/class/misc/$foo.
udev may create the /dev/watchdog node if the driver is loaded.
I dont have such a device, so I cant test it.
The drivers below provide names with spaces and even with / in it.
Not a big deal, but apps may expect /dev/watchdog.
Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
[PATCH] uclinux: use MAP_PRIVATE when mmaping code regions in flat binary loader
Use MAP_PRIVATE when calling mmap to get memory for the code region.
The flat loader was using MAP_SHARED, but underlying changes to the
MMUless mmap means this is now wrong.
[PATCH] m68knommu: new board support in linker script
. add support for the M5235EVB board
. add support for the SOM5282 board
. add support for the MOD5272 board
. fix end of memory define for eLITE board
[PATCH] m68knommu: new family (523x) and board config support
New architecture and board configuration support for m68knommu.
. add 523x ColdFire support
. add support for SOM5282 and MOD5272 boards
. break up the 527x to be separate 5271 and 5275. There is some
subtle differences that (like RAM config) that need to be dealt with
. add option to support selecting 4k kernel stack
Make show_stack() consistent with other architectures.
Put the vector string names in the .rodata section.
Patch originally submitted by Philippe De Muyter <phdm@macqel.be>.
[PATCH] m68knommu: fix ColdFire startup code to properly handle non 0 based ram
Correctly determine the end of ram for ram setups that do not
start at base address of 0. Add support for the MOD5272 board,
which doesn not have a ram base of 0.
Russell King [Thu, 1 Sep 2005 21:41:55 +0000 (22:41 +0100)]
[ARM] Fix ARMv6 page table bits
We weren't explicitly setting the page table bits we desired
in user_prot in the protection table, which resulted in the
user mappings for v6 CPUs being marked global.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kumar Gala [Wed, 31 Aug 2005 04:54:47 +0000 (14:54 +1000)]
[PATCH] ppc: L2 cache prefetch fixes on 745x
We run into problems if we blindly enable L2 prefetching without
checking that the L2 cache is actually enabled. Additionaly, if we
disable the L2 cache we need to ensure that we disable L2 prefetching.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a problem with pci_map_rom() which doesn't properly
update the ROM BAR value with the address thas allocated for it by the
PCI code. This problem, among other, breaks boot on Mac laptops.
It'ss a new version based on Linus latest one with better error
checking.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adrian Bunk [Wed, 31 Aug 2005 15:43:51 +0000 (17:43 +0200)]
[PATCH] Add missing select's to DVB_BUDGET_AV
This fixes the following compile error:
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `frontend_init':
budget-av.c:(.text+0xb9448): undefined reference to `tda10046_attach'
budget-av.c:(.text+0xb9518): undefined reference to `tda10021_attach'
drivers/built-in.o: In function `philips_tu1216_request_firmware':
budget-av.c:(.text+0xb937b): undefined reference to `request_firmware'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Johannes Stezenbach <js@linuxtv.org> Acked-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The prototype for sys_fadvise64_64() is:
long sys_fadvise64_64(int fd, loff_t offset, loff_t len, int advice)
The argument list is therefore as follows on legacy ABI:
fd: type int (r0)
offset: type long long (r1-r2)
len: type long long (r3-sp[0])
advice: type int (sp[4])
With EABI this becomes:
fd: type int (r0)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
advice: type int (sp[8])
Not only do we have ABI differences here, but the EABI version requires
one additional word on the syscall stack.
To avoid the ABI mismatch and the extra stack space required with EABI
this syscall is now defined with a different argument ordering
on ARM as follows:
long sys_arm_fadvise64_64(int fd, int advice, loff_t offset, loff_t len)
This gives us the following ABI independent argument distribution:
fd: type int (r0)
advice: type int (r1)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
Now, since the syscall entry code takes care of 5 registers only by
default including the store of r4 to the stack, we need a wrapper to
store r5 to the stack as well. Because that wrapper was missing and was
always required this means that sys_fadvise64_64 never worked on ARM and
therefore we can safely reuse its syscall number for our new
sys_arm_fadvise64_64 interface.
Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jouni Malinen [Mon, 29 Aug 2005 00:53:32 +0000 (17:53 -0700)]
[PATCH] hostap: Fix null pointer dereference in prism2_pccard_card_present()
local->hw_priv was initialized only after the interrupt handler was
registered. This could trigger a NULL pointer dereference in
prism2_pccard_card_present() that assumed that local->hw_priv is always
set (and it should have been). Fix this by setting local->hw_priv before
registering the interrupt handler.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Be consistent about driver name, increment version
The iseries_veth driver tells sysfs that it's called 'iseries_veth', but if
you ask it via ethtool it thinks it's called 'veth'. I think this comes from
2.4 when the driver was called 'veth', but it's definitely called
'iseries_veth' now, so fix it.
To make sure we don't do it again define DRV_NAME and use it everywhere.
While we're at it, change the version number to 2.0, to reflect the changes
made in this patch series.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Add sysfs support for connection structs
To aid in field debugging, add sysfs support for iseries_veth's connection
structures. At the moment this is all read-only, however we could think about
adding write support for some attributes in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Fix bogus counting of TX errors
There's a number of problems with the way iseries_veth counts TX errors.
Firstly it counts conditions which aren't really errors as TX errors. This
includes if we don't have a connection struct for the other LPAR, or if the
other LPAR is currently down (or just doesn't want to talk to us). Neither
of these should count as TX errors.
Secondly, it counts one TX error for each LPAR that fails to accept the packet.
This can lead to TX error counts higher than the total number of packets sent
through the interface. This is confusing for users.
This patch fixes that behaviour. The non-error conditions are no longer
counted, and we introduce a new and I think saner meaning to the TX counts.
If a packet is successfully transmitted to any LPAR then it is transmitted
and tx_packets is incremented by 1.
If there is an error transmitting a packet to any LPAR then that is counted
as one error, ie. tx_errors is incremented by 1.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The iseries_veth driver often has multiple netdevices sending packets over
a single connection to another LPAR. If the bandwidth to the other LPAR is
exceeded, all the netdevices must have their queues stopped.
The current code achieves this by queueing one incoming skb on the
per-netdevice port structure. When the connection is able to send more packets
we iterate through the port structs and flush any packet that is queued,
as well as restarting the associated netdevice's queue.
This arrangement makes less sense now that we have per-connection TX timers,
rather than the per-netdevice generic TX timer.
The new code simply detects when one of the connections is full, and stops
the queue of all associated netdevices. Then when a packet is acked on that
connection (ie. there is space again) all the queues are woken up.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Add a per-connection ack timer
Currently the iseries_veth driver contravenes the specification in
Documentation/networking/driver.txt, in that if packets are not acked by
the other LPAR they will sit around forever.
This patch adds a per-connection timer which fires if we've had no acks for
five seconds. This is superior to the generic TX timer because it catches
the case of a small number of packets being sent and never acked.
This fixes a bug we were seeing on real systems, where some IPv6 neighbour
discovery packets would not be acked and then prevent the module from being
removed, due to skbs lying around.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Use kobjects to track lifecycle of connection structs
The iseries_veth driver can attach to multiple vlans, which correspond to
multiple net devices. However there is only 1 connection between each LPAR,
so the connection structure may be shared by multiple net devices.
This makes module removal messy, because we can't deallocate the connections
until we know there are no net devices still using them. The solution is to
use ref counts on the connections, so we can delete them (actually stop) as
soon as the ref count hits zero.
This patch fixes (part of) a bug we were seeing with IPv6 sending probes to
a dead LPAR, which would then hang us forever due to leftover skbs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Make init_connection() & destroy_connection() symmetrical
This patch makes veth_init_connection() and veth_destroy_connection()
symmetrical in that they allocate/deallocate the same data.
Currently if there's an error while initialising connections (ie. ENOMEM)
we call veth_module_cleanup(), however this will oops because we call
driver_unregister() before we've called driver_register(). I've never seen
this actually happen though.
So instead we explicitly call veth_destroy_connection() for each connection,
any that have been set up will be deallocated.
We also fix a potential leak if vio_register_driver() fails.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Only call dma_unmap_single() if dma_map_single() succeeded
The iseries_veth driver unconditionally calls dma_unmap_single() even
when the corresponding dma_map_single() may have failed.
Rework the code a bit to keep the return value from dma_unmap_single()
around, and then check if it's a dma_mapping_error() before we do
the dma_unmap_single().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Replace lock-protected atomic with an ordinary variable
The iseries_veth driver uses atomic ops to manipulate the in_use field of
one of its per-connection structures. However all references to the
flag occur while the connection's lock is held, so the atomic ops aren't
necessary.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The iseries_veth driver keeps a stack of messages for each connection
and a lock to protect the stack. However there is also a per-connection lock
which makes the message stack lock redundant.
Remove the message stack lock and document the fact that callers of the
stack-manipulation functions must hold the connection's lock.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Due to a logic bug, once promiscuous mode is enabled in the iseries_veth
driver it is never disabled.
The driver keeps two flags, promiscuous and all_mcast which have exactly the
same effect. This is because we only ever receive packets destined for us,
or multicast packets. So consolidate them into one promiscuous flag for
simplicity.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Try to avoid pathological reset behaviour
The iseries_veth driver contains a state machine which is used to manage
how connections are setup and neogotiated between LPARs.
If one side of a connection resets for some reason, the two LPARs can get
stuck in a race to re-setup the connection. This can lead to the connection
being declared dead by one or both ends. In practice the connection is
declared dead by one or both ends approximately 8/10 times a connection is
reset, although it is rare for connections to be reset.
(an example here: http://michael.ellerman.id.au/files/misc/veth-trace.html)
The core of the problem is that the end that resets the connection doesn't
wait for the other end to become aware of the reset. So the resetting end
starts setting the connection back up, and then receives a reset from the
other end (which is the response to the initial reset). And so on.
We're severely limited in what we can do to fix this. The protocol between
LPARs is essentially fixed, as we have to interoperate with both OS/400
and old Linux drivers. Which also means we need a fix that only changes the
code on one end.
The only fix I've found given that, is to just blindly sleep for a bit when
resetting the connection, in the hope that the other end will get itself
sorted. Needless to say I'd love it if someone has a better idea.
This does work, I've so far been unable to get it to break, whereas without
the fix a reset of one end will lead to a dead connection ~8/10 times.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Remove a FIXME WRT deletion of the ack_timer
The iseries_veth driver has a timer which we use to send acks. When the
connection is reset or stopped we need to delete the timer.
Currently we only call del_timer() when resetting a connection, which means
the timer might run again while the connection is being re-setup. As it turns
out that's ok, because the flags the timer consults have been reset.
It's cleaner though to call del_timer_sync() once we've dropped the lock,
although the timer may still run between us dropping the lock and calling
del_timer_sync(), but as above that's ok.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] iseries_veth: Cleanup error and debug messages
Currently the iseries_veth driver prints the file name and line number in its
error messages. This isn't very useful for most users, so just print
"iseries_veth: message" instead.
- convert uses of veth_printk() to veth_debug()/veth_error()/veth_info()
- make terminology consistent, ie. always refer to LPAR not lpar
- be consistent about printing return codes as %d not %x
- make format strings fit in 80 columns
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
David Vrabel [Wed, 31 Aug 2005 20:45:14 +0000 (21:45 +0100)]
[ARM] 2869/1: ixp4xx: correct ioread*/iowrite*
Patch from David Vrabel
Correct the ioread* and iowrite* functions. In particular, add an offset to the cookie in ioport_map so we can map I/O port ranges starting from 0 (0 is for reporting errors).
Signed-off-by: David Vrabel <dvrabel@arcom.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Steve Longerbeam [Wed, 31 Aug 2005 20:22:20 +0000 (21:22 +0100)]
[ARM] 2867/2: unaligned ldrd/strd fixups
Patch from Steve Longerbeam
Adds an implementation of unaligned LDRD and STRD fixups.
Also fixes a bug where do_alignment() would misinterpret and
fixup an unaligned LDRD/STRD as LDRH/STRH, causing memory
corruption.
This is the same as Patch #2867/1, but with minor whitespace
and comments changes, plus a check for arch-level >= v5TE
before printing ai_dword count in proc_alignment_read().
Signed-off-by: Steve Longerbeam <stevel@mwwireless.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 31 Aug 2005 09:12:14 +0000 (10:12 +0100)]
[SERIAL] Clean up and fix tty transmission start/stoping
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)
There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive. In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.
There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.
Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Luck [Tue, 30 Aug 2005 21:59:24 +0000 (14:59 -0700)]
[IA64] Low byte of current->personality is not a bitmask.
Peter Staubach pointed out that it is not correct to check
current->personality & PER_LINUX32 (this will have false
hits on several other personality values).
I had some time to think about PCI assign issues in 2.6.13-rc series.
The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:
/**
* Reserve motherboard resources after PCI claim BARs,
* but before PCI assign resources for uninitialized PCI devices
*/
So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.
Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
it duplicates pci_assign_unassigned_resources() functionality and
actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
various setups.
Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Clemens Ladisch [Tue, 2 Aug 2005 13:26:52 +0000 (15:26 +0200)]
[ALSA] usb-audio: throttle MIDI URB resubmits on USB errors
USB generic driver
When a USB error occurs that might indicate that the device has been
unplugged, don't resubmit the URB immediately to prevent flooding the
log with error messages before khubd has us disconnect()ed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Emagic devices pad their packets not with 0xff bytes but with a 0xff
byte followed by garbage, so we have to stop at the first such byte.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Takashi Iwai [Wed, 24 Aug 2005 12:14:57 +0000 (14:14 +0200)]
[ALSA] hda-intel - Fix ULI M5461 support
HDA Intel driver
Fix and clean up for the support of ULI M5461
- set CORB/RIRB sizes explicitly
- add workarounds for ULI on ia32
- max number of streams depends on the chip type now
- increase the size of BDL
projects / linux-2.6-omap-h63xx.git / log