Max Krasnyansky [Thu, 29 May 2008 18:02:52 +0000 (11:02 -0700)]
genirq: Expose default irq affinity mask (take 3)
Current IRQ affinity interface does not provide a way to set affinity
for the IRQs that will be allocated/activated in the future.
This patch creates /proc/irq/default_smp_affinity that lets users set
default affinity mask for the newly allocated IRQs. Changing the default
does not affect affinity masks for the currently active IRQs, they
have to be changed explicitly.
Updated based on Paul J's comments and added some more documentation.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com> Cc: pj@sgi.com Cc: a.p.zijlstra@chello.nl Cc: tglx@linutronix.de Cc: rdunlap@xenotime.net Cc: mingo@elte.hu Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Anton Vorontsov [Sun, 1 Jun 2008 09:49:32 +0000 (11:49 +0200)]
mmc_spi: mmc_spi.h should include linux/interrupts.h
Since mmc_spi.h uses irqreturn_t type, it should include appropriate
header, otherwise build will break if users didn't include it (some of
them do not use interrupts).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 2 Jun 2008 22:25:27 +0000 (15:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
8250 Serial Driver: revert extra IRQ flag definition patch
Blackfin arch: update anomaly headers from toolchain trunk
Blackfin arch: Remove bad and usless code
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
Blackfin arch: Fix typo. it should be _outsw_8
Blackfin arch: Cleanup no functional changes
Bryan Wu [Sat, 31 May 2008 08:10:04 +0000 (16:10 +0800)]
8250 Serial Driver: revert extra IRQ flag definition patch
As Russell pointed out, original patch will break some serial configurations
because of the dependency of the <asm/serial.h> header file.
Revert it first and try to find out other solution later
Cc: Javier Herrero <jherrero@hvsistemas.es> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Bryan Wu [Sat, 31 May 2008 07:17:25 +0000 (15:17 +0800)]
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
AD7877 use SSEL_2 (P9.9) and IRQ_PF8 (P9.14) on BF527
- populating JP3 to enable STAMP
- disable SW11.2 to disconnect SSEL_2/PF12 from Rotary NAND
- disable SW18.1 to disconnect SSEL_2 from MAX1233 touchscreen chip
Gcc might re-order MMIO accessors vs. surrounding consistent
memory accesses, which is a "bad thing", and could break drivers.
This fixes it by adding a "memory" clobber to the MMIO accessors,
which should prevent gcc from doing that reordering.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Joel Becker [Sat, 10 May 2008 01:49:29 +0000 (18:49 -0700)]
ocfs2: Rename 'user_stack' plugin structure to 'ocfs2_user_plugin'
The static structure describing the userspace cluster plugin for ocfs2
was named 'user_stack', which is a real pain when people are grep(1)ing
the tree for the program stack object 'user_stack'. Change the name to
something distinct and namespaced.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
Ingo Molnar [Fri, 30 May 2008 15:02:50 +0000 (17:02 +0200)]
drivers/watchdog/geodewdt.c: build fix
* Wim Van Sebroeck <wim@iguana.be> wrote:
> Author: Jordan Crouse <jordan.crouse@amd.com>
> Date: Mon Jan 21 10:07:00 2008 -0700
>
> [WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
-tip testing found the following build failure on latest -git:
drivers/watchdog/geodewdt.c: In function 'geodewdt_probe':
drivers/watchdog/geodewdt.c:225: error: too many arguments to function 'geode_mfgpt_alloc_timer'
make[1]: *** [drivers/watchdog/geodewdt.o] Error 1
make: *** [drivers/watchdog/geodewdt.o] Error 2
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
peerchen [Mon, 19 May 2008 06:44:57 +0000 (14:44 +0800)]
ahci: change the Device IDs of nvidia MCP7B AHCI controller in ahci.c
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes
the issue, it clearly also adds port multipler support. The current
2.6.26-rc driver is broken.
On boot with debug enabled we get something like (w/o this patch):
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
.. continues for ever.
This change fixes this as a side effect of adding port multiplier support.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Wed, 21 May 2008 05:11:24 +0000 (14:11 +0900)]
libata: SRST can't be trusted on PMP sil3726
As in sil4726, SRST can't be trusted on sil3726 causing detection
problems under certain configuraitons. I thought it was from the
Config Disk device but apparently not.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Randy Dunlap [Wed, 30 Apr 2008 19:57:00 +0000 (12:57 -0700)]
libata: fix libata-scsi kernel-doc notation
Fix libata-scsi kernel-doc notation:
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 29 May 2008 13:04:22 +0000 (22:04 +0900)]
ata_piix: fix macbook ich8m problems
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.
This patch works around macbook ich8m problems by
* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata
Mark Lord [Tue, 27 May 2008 21:58:56 +0000 (17:58 -0400)]
sata_mv: nuke unreleased GenIIe revisions
The only public release of the 6042/7042 chips was/is revision "B0".
Remove code that attempted to deal with earlier, non-released revs.
This matches the logic of the current Marvell "proprietary" driver.
Also, bump up the sata_mv version number, to reflect this batch of erratas.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Tue, 27 May 2008 21:54:48 +0000 (17:54 -0400)]
sata_mv: move SOC_FLAG to hpriv
Convert the System-on-Chip flag from a host flag to an hpriv flag,
for better consistency with other chip-rev flags, and for easier use
in errata fixes etc.
Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency
of naming/use (everything else SOC-related already uses "SOC").
There are no functionality changes in this patch.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Fri, 30 May 2008 14:44:19 +0000 (07:44 -0700)]
Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] disassembler: fix idte instruction format.
[S390] tape: fix race with stack local wait_queue_head_t.
[S390] 3270: fix race with stack local wait_queue_head_t.
[S390] dasd: use a generic wait_queue for sleep_on
[S390] sclp_vt220: fix scheduling while atomic bug.
[S390] showmem: Only walk spanned pages.
[S390] appldata: prevent cpu hotplug when walking cpu_online_map.
[S390] Fix section mismatch warnings.
[S390] s390 types: make dma_addr_t 64 bit capable
[S390] tape: Fix race condition in tape block device driver
[S390] fix sparsemem related compile error with allnoconfig on s390
Harvey Harrison [Fri, 30 May 2008 00:51:57 +0000 (17:51 -0700)]
acpi: fix sparse const errors
In this case we want a constant pointer to constant chars:
drivers/misc/thinkpad_acpi.c:3824:19: error: Just how const do you want this type to be?
Like the error says.
drivers/misc/thinkpad_acpi.c:3863:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3864:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3865:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3866:19: error: Just how const do you want this type to be?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SW_RADIO code for EV_SW events has a name that is not descriptive
enough of its intended function, and could induce someone to think
KEY_RADIO is its EV_KEY counterpart, which is false.
Rename it to SW_RFKILL_ALL, and document what this event is for. Keep
the old name around, to avoid userspace ABI breaks.
The SW_RFKILL_ALL event is meant to be used by rfkill master switches. It
is not bound to a particular radio switch type, and usually applies to all
types. It is semantically tied to master rfkill switches that enable or
disable every radio in a system.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
llc_sap_rcv was being preceded by skb_set_owner_r, then calling
llc_state_process that calls sock_queue_rcv_skb, that in turn calls
skb_set_owner_r again making the space allowed to be used by the socket to be
leaked, making the socket to get stuck.
Fix it by setting skb->sk at llc_sap_rcv and leave the accounting to be done
only at sock_queue_rcv_skb.
Reported-by: Dmitry Petukhov <dmgenp@gmail.com> Tested-by: Dmitry Petukhov <dmgenp@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[S390] tape: fix race with stack local wait_queue_head_t.
A wait_event call with a stack local wait_queue_head_t structure that is
used to do the wake up for the wait_event is inherently racy. After the
wait_event finished the wake_up call might not have completed yet.
Replace the stack local wait_queue_head_t in tape_do_io and
tape_do_io_interruptible with a per device wait queue.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] 3270: fix race with stack local wait_queue_head_t.
A wait_event call with a stack local wait_queue_head_t structure that is
used to do the wake up for the wait_event is inherently racy. After the
wait_event finished the wake_up call might not have completed yet.
Remove the stack local wait_queue_head_t from raw3270_start_init and
use the global raw3270_wait_queue instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Haberland [Fri, 30 May 2008 08:03:31 +0000 (10:03 +0200)]
[S390] dasd: use a generic wait_queue for sleep_on
Use a generic wait_queue to prevent the wait_queue in dasd_sleep_on_
functions from being referenced by callback_data while it does not
exist any more.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 30 May 2008 08:03:30 +0000 (10:03 +0200)]
[S390] sclp_vt220: fix scheduling while atomic bug.
The driver incorrectly assumed that putchar will only be called from
schedulable process context and therefore blocked and waited if no
free output buffers where available.
Since putchar may also be called from BH context this may lead to
deadlocks.
To fix this just return the number of characters accepted and let the
upper layer handle the rest.
The console write function will busy wait (sclp_sync_wait) until a
buffer is available again.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 30 May 2008 08:03:29 +0000 (10:03 +0200)]
[S390] showmem: Only walk spanned pages.
Convert show_mem() so its nearly the same as on x86/powerpc.
Gives us proper locking and we get also rid of the only use of max_mapnr.
Also the number of pages was contained in an int which might not be
sufficient not too far in the future.
Cc: Johannes Weiner <hannes@saeurebad.de> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 30 May 2008 08:03:27 +0000 (10:03 +0200)]
[S390] Fix section mismatch warnings.
This fixes the last remaining section mismatch warnings in s390
architecture code. It reveals also a real bug introduced by... me
with git commit 2069e978d5a6e7b45d58027e3de7f879b8c5e488
("[S390] sparsemem vmemmap: initialize memmap.")
Calling the generic vmemmap_alloc_block() function to get initialized
memory is a nice idea, however that function is __meminit annotated
and therefore the function might be gone if we try to call it later.
This can happen if a DCSS segment gets added.
So basically revert the patch and clear the memmap explicitly to fix
the original bug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
virtio tests with guests larger than 4 GB revealed that the dma_addr_t
definition for s390 did not make it into the 64bit world.
This patch changes the definition on s390 to have an u64 on 64bit and
u32 on 32bit systems.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Fri, 30 May 2008 08:03:25 +0000 (10:03 +0200)]
[S390] tape: Fix race condition in tape block device driver
Due to incorrect function call sequence it can happen that a tape block
request is finished before the request is taken from the block request queue.
The following sequence leads to that condition:
* tapeblock_start_request() -> start CCW program
* Request finishes -> IO interrupt
* tapeblock_end_request()
* end_that_request_last()
If blkdev_dequeue_request() has not been called before end_that_request_last(),
a kernel bug is triggered in end_that_request_last() because the request is
still queued. To solve that problem blkdev_dequeue_request() has to be called
before starting the CCW program.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rusty Russell [Fri, 30 May 2008 20:09:46 +0000 (15:09 -0500)]
lguest: notify on empty
This is the lguest implementation of the VIRTIO_F_NOTIFY_ON_EMPTY feature.
It is currently only published for network devices, but it is turned on for
everyone.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Fri, 30 May 2008 20:09:45 +0000 (15:09 -0500)]
virtio: force callback on empty.
virtio allows drivers to suppress callbacks (ie. interrupts) for
efficiency (no locking, it's just an optimization).
There's a similar mechanism for the host to suppress notifications
coming from the guest: in that case, we ignore the suppression if the
ring is completely full.
It turns out that life is simpler if the host similarly ignores
callback suppression when the ring is completely empty: the network
driver wants to free up old packets in a timely manner, and otherwise
has to use a timer to poll.
We have to remove the code which ignores interrupts when the driver
has disabled them (again, it had no locking and hence was unreliable
anyway).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_config: fix len calculation of config elements
Rusty,
This patch is a prereq for the virtio_blk blocksize patch, please apply it
first.
Adding an u32 value to the virtio_blk_config unconvered a small bug the config
space defintions:
v is a pointer, to we have to use sizeof(*v) instead of sizeof(v).
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_net: another race with virtio_net and enable_cb
Hello Rusty,
seems that we still have a problem with virtio_net and the enable_cb callback.
During a long running network stress tests with virtio and got the following
oops:
I looked into the virtio_net code for some time and I think the following
scenario happened. Please look at virtnet_poll:
[...]
/* Out of packets? */
if (received < budget) {
netif_rx_complete(vi->dev, napi);
if (unlikely(!vi->rvq->vq_ops->enable_cb(vi->rvq))
&& napi_schedule_prep(napi)) {
vi->rvq->vq_ops->disable_cb(vi->rvq);
__netif_rx_schedule(vi->dev, napi);
goto again;
}
}
If an interrupt arrives after netif_rx_complete, a second poll routine can run
on a different cpu. The second check for napi_schedule_prep would prevent any
harm in the network stack, but we have called enable_cb possibly after the
disable_cb in skb_recv_done.
static void skb_recv_done(struct virtqueue *rvq)
{
struct virtnet_info *vi = rvq->vdev->priv;
/* Schedule NAPI, Suppress further interrupts if successful. */
if (netif_rx_schedule_prep(vi->dev, &vi->napi)) {
rvq->vq_ops->disable_cb(rvq);
__netif_rx_schedule(vi->dev, &vi->napi);
}
}
That means that the second poll routine runs with interrupts enabled, which is
ok, since we can handle additional interrupts. The problem is now that the
second poll routine might also call enable_cb, triggering the BUG.
The only solution I can come up with, is to remove the BUG statement in
enable_cb - similar to disable_cb. Opinions or better ideas where the oops
could come from?
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Fri, 30 May 2008 20:09:44 +0000 (15:09 -0500)]
virtio: An entropy device, as suggested by hpa.
Note that by itself, having a "hardware" random generator does very
little: you should probably run "rngd" in your guest to feed this into
the kernel entropy pool.
Included:
virtio_rng: dont use vmalloced addresses for virtio
If virtio_rng is build as a module, random_data is an address
in vmalloc space. As virtio expects guest real addresses, this
can cause any kind of funny behaviour, so lets allocate
random_data dynamically with kmalloc.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
sometimes it is useful to share a disk (e.g. usr). To avoid file system
corruption, the disk should be mounted read-only in that case. This patch
adds a new feature flag, that allows the host to specify, if the disk should
be considered read-only.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Fri, 30 May 2008 20:09:42 +0000 (15:09 -0500)]
virtio: set device index in common code.
Anthony Liguori points out that three different transports use the virtio code,
but each one keeps its own counter to set the virtio_device's index field. In
theory (though not in current practice) this means that names could be
duplicated, and that risk grows as more transports are created.
So we move the selection of the unique virtio_device.index into the common code
in virtio.c, which has the side-benefit of removing duplicate code.
The only complexity is that lguest and S/390 use the index to uniquely identify
the device in case of catastrophic failure before register_virtio_device() is
called: now we use the offset within the descriptor page as a unique identifier
for the printks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Carsten Otte <cotte@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Chris Lalancette <clalance@redhat.com> Cc: Anthony Liguori <anthony@codemonkey.ws>
Rusty Russell [Fri, 30 May 2008 20:09:41 +0000 (15:09 -0500)]
virtio: bus_id for devices should contain 'virtio'
Chris Lalancette <clalance@redhat.com> points out that virtio.c sets all device
names to '0', '1', etc, which looks silly in /proc/interrupts. We change this
from '%d' to 'virtio%d'.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Carsten Otte <cotte@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Chris Lalancette <clalance@redhat.com> Cc: Anthony Liguori <anthony@codemonkey.ws>
Chris Lalancette [Fri, 30 May 2008 20:09:41 +0000 (15:09 -0500)]
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
Fix a modprobe virtio_blk ; rmmod virtio_blk ; modprobe virtio_blk crash; this
was basically because we weren't doing "del_gendisk()" in the remove path.
Signed-off-by: Chris Lalancette <clalance@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (moved del_gendisk up)
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: EHCI: fix performance regression"
USB: fsl_usb2_udc: fix recursive lock
USB: usb-serial: option: Don't match Huawei driver CD images
USB: pl2303: another product ID
USB: add another scanner quirk
USB: Add support for ROKR W5 in unusual_devs.h
USB: Fix M600i unusual_devs entry
USB: usb-storage: unusual_devs update for Cypress ATACB
USB: EHCI: fix performance regression
USB: EHCI: fix bug in Iso scheduling
USB: EHCI: fix remote-wakeup regression
USB: EHCI: suppress unwanted error messages
USB: EHCI: fix up root-hub TT mess
USB: add all configs to the "descriptors" attribute
USB: fix possible deadlock involving sysfs attributes
USB: Firmware loader driver for USB Apple iSight camera
USB: FTDI_SIO : Add support for Matrix Orbital PID Range
Signed-off-by: Li Yang <leoli@freescale.com> Cc: Eugene T. Bordenkircher <Eugene_Bordenkircher@selinc.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Karcher [Wed, 28 May 2008 21:58:18 +0000 (23:58 +0200)]
USB: usb-serial: option: Don't match Huawei driver CD images
Add the interface info matching to all Huawei cards, as they all also
contain a Mass Storage Device interface (usually containing Windows
drivers) which should not get bound by this driver.
See also drivers/usb/storage/unusual_devs.h
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Steve Murphy [Fri, 23 May 2008 18:09:05 +0000 (23:39 +0530)]
USB: pl2303: another product ID
I've just got a USB GPRS/EDGE modem branded Manufacturer Micromax Model
MMX610U (see http://www.airtel.in/level2_t3data.aspx?path=1/106/179)
working by adding another product ID to pl2303. Modem info reports same
module as Max Arnold's i.e.SIMCOM SIM600 but with product ID 0x0612
(cf Ox0611).
From: Steve Murphy <steve@gnusis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
René Rebe [Tue, 27 May 2008 07:05:46 +0000 (09:05 +0200)]
USB: add another scanner quirk
Like the HP53{00,70} scanner other devices of the OEM Avision require
the USB_QUIRK_STRING_FETCH_255 to correct set a configuration with
"recent" Linux kernels.
Signed-off-by: René Rebe <rene@exactcode.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz [Mon, 26 May 2008 19:33:58 +0000 (21:33 +0200)]
USB: Fix M600i unusual_devs entry
It turns out that the unusual_devs entry for the Motorola M600i needs
another flag. This patch adds it. Thanks to Atte André Jensen
<atte@ballbreaker.dk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 21 May 2008 17:53:01 +0000 (13:53 -0400)]
USB: usb-storage: unusual_devs update for Cypress ATACB
This patch (as1101) updates the unusual_devs entry for the Cypress
ATACB pass-through. The protocol field is changed from US_PR_BULK to
US_PR_DEVICE, since the Cypress devices already set bInterfaceProtocol
to Bulk-only.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 May 2008 20:59:33 +0000 (16:59 -0400)]
USB: EHCI: fix performance regression
This patch (as1099) fixes a performance regression in ehci-hcd. The
fundamental problem is that queue headers get removed from the
schedule too quickly, since the code checks for a counter advancing
rather than making an actual time-based check. The latency involved
in removing the queue header and then relinking it can severely
degrade certain kinds of workloads.
The patch replaces a simple counter with a timestamp derived from the
controller's uframe value. In addition, the delay for unlinking an
idle queue header is increased from 5 ms to 10 ms; since some
controllers (nVidia) have a latency of up to 1 ms for unlinking, this
reduces the relative impact from 20% to 10%.
Finally, a logical error left over from the IAA watchdog-timer
conversion is corrected. Now the driver will always either unlink an
idle queue header or set up a timer to unlink it later. The old code
would sometimes fail to do either.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Cc: Leonid <leonidv11@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 May 2008 20:59:10 +0000 (16:59 -0400)]
USB: EHCI: fix bug in Iso scheduling
This patch (as1098) changes the way ehci-hcd schedules its periodic
Iso transfers. That the current scheduling code is wrong is clear on
the face of it: Sometimes it returns -EL2NSYNC (meaning that an URB
couldn't be scheduled because it was submitted too late), but it does
this even when the URB_ISO_ASAP flag is set (meaning the URB should be
scheduled as soon as possible).
The new code properly implements as-soon-as-possible scheduling,
assigning the next unexpired slot as the URB's starting point. It
also is more careful about checking for Iso URB completion: It doesn't
bother to check for activity during frames that are already over,
and it allows for the possibility that some of the URB's packets may
have raced the hardware when they were submitted and so never got used
(the packet status is set to -EXDEV).
This fixes problems several people have experienced with USB video
applications.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 May 2008 20:58:58 +0000 (16:58 -0400)]
USB: EHCI: fix remote-wakeup regression
This patch (as1097) fixes a bug in the remote-wakeup handling in
ehci-hcd. The driver currently does not keep track of whether the
change-suspend feature is enabled for each port; the feature is
automatically reset the first time it is read. But recent changes to
the hub driver require that the feature be read at least twice in
order to work properly.
A bit-vector is added for storing the change-suspend feature values.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 May 2008 20:58:29 +0000 (16:58 -0400)]
USB: EHCI: suppress unwanted error messages
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 May 2008 20:58:11 +0000 (16:58 -0400)]
USB: EHCI: fix up root-hub TT mess
This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.
Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures. Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might. So the patch adds it where it is missing.
Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods. These method pointers are
specific to PCI and shouldn't be used otherwise.
(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Alan Stern [Tue, 20 May 2008 20:40:42 +0000 (16:40 -0400)]
USB: add all configs to the "descriptors" attribute
This patch (as1094) changes the output of the "descriptors" binary
attribute. Now it will contain the device descriptor followed by all
the configuration descriptors, not just the descriptor for the current
config.
Userspace libraries want to have access to the kernel's cached
descriptor information, so they can learn about device characteristics
without having to wake up suspended devices. So far the only user of
this attribute is the new libusb-1.0 library; thus changing its
contents shouldn't cause any problems.
This should be considered for 2.6.26, if for no other reason than to
minimize the range of releases in which the attribute contains only the
current config descriptor.
Also, it doesn't hurt that the patch removes the device locking --
which was formerly needed in order to know for certain which config was
indeed current.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 May 2008 20:37:34 +0000 (16:37 -0400)]
USB: fix possible deadlock involving sysfs attributes
There is a potential deadlock when the usb_generic driver is unbound
from a device. The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs. If a user task happens to be running an attribute method
at the time, the removal will block until the method returns. But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!
This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.
Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered. So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Garrett [Tue, 20 May 2008 19:06:28 +0000 (20:06 +0100)]
USB: Firmware loader driver for USB Apple iSight camera
Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ray Molenkamp [Wed, 21 May 2008 23:06:26 +0000 (17:06 -0600)]
USB: FTDI_SIO : Add support for Matrix Orbital PID Range
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lothar Waßmann [Thu, 29 May 2008 15:54:52 +0000 (17:54 +0200)]
[CPUFREQ] fix double unlock of cpu_policy_rwsem in drivers/cpufreq/cpufreq.c
In drivers/cpufreq/cpufreq.c the function cpufreq_add_dev() takes the
error exit 'err_out_unregister' from different places once with the
'cpu_policy_rwsem' lock held, once with the lock released:
| if (ret)
| goto err_out_unregister;
| }
|
| policy->governor = NULL; /* to assure that the starting sequence is
| * run in cpufreq_set_policy */
|
| /* set default policy */
| ret = __cpufreq_set_policy(policy, &new_policy);
| policy->user_policy.policy = policy->policy;
| policy->user_policy.governor = policy->governor;
|
| unlock_policy_rwsem_write(cpu);
|
| if (ret) {
| dprintk("setting policy failed\n");
| goto err_out_unregister;
| }
This leads to the following error message in case of a failing
__cpufreq_set_policy() call:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
swapper/1 is trying to release lock (&per_cpu(cpu_policy_rwsem, cpu)) at:
[<c01b4564>] unlock_policy_rwsem_write+0x30/0x40
but there are no more locks to release!
other info that might help us debug this:
1 lock held by swapper/1:
#0: (sysdev_drivers_lock){--..}, at: [<c018fd18>] sysdev_driver_register+0x74/0x130
this change also improves lat_ctx from 6.69 usecs to 1.11 usec:
$ ./lat_ctx -s 0 2
"size=0k ovr=1.19
2 1.11
$ ./lat_ctx -s 0 2
"size=0k ovr=1.22
2 6.69
in sysbench it's an overall win with some weakness at the lots-of-clients
side. That happens because we now under-balance this workload
a bit. To counter that effect, turn on NEWIDLE:
as a bonus this not only improves the many-clients case but
also improves the (more important) rampup phase.
sysbench is a workload that quickly breaks down if the
scheduler over-balances, so since it showed an improvement
under NEWIDLE this change is definitely good.
Alexey Dobriyan [Thu, 29 May 2008 10:19:37 +0000 (03:19 -0700)]
netfilter: nf_conntrack_expect: fix error path unwind in nf_conntrack_expect_init()
Signed-off-by: Alexey Dobriyan <adobriyan@parallels.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo Molnar [Thu, 29 May 2008 09:28:57 +0000 (11:28 +0200)]
revert ("sched: fair-group: SMP-nice for group scheduling")
Yanmin Zhang reported:
Comparing with 2.6.25, volanoMark has big regression with kernel 2.6.26-rc1.
It's about 50% on my 8-core stoakley, 16-core tigerton, and Itanium Montecito.
projects / linux-2.6-omap-h63xx.git / log