Maciej Sosnowski [Wed, 23 Jul 2008 00:30:57 +0000 (17:30 -0700)]
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0). This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.
[dan.j.williams@intel.com: remove some ifdefs] Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Maciej Sosnowski [Tue, 22 Jul 2008 17:07:33 +0000 (10:07 -0700)]
I/OAT: Add watchdog/reset functionality to ioatdma
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 18 Jul 2008 00:59:56 +0000 (17:59 -0700)]
iop_adma: directly reclaim descriptors on allocation failure
Force callers that trigger an "out of descriptors" condition to run the
cleanup loop directly. Alleviates the requirement to have soft-irqs
enabled when polling for a descriptor in async_xor.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 18 Jul 2008 00:59:55 +0000 (17:59 -0700)]
async_tx: remove depend_tx from async_tx_sync_epilog
All callers of async_tx_sync_epilog have called async_tx_quiesce on the
depend_tx, so async_tx_sync_epilog need only call the callback to
complete the operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 18 Jul 2008 00:59:55 +0000 (17:59 -0700)]
async_tx: fix handling of the "out of descriptor" condition in async_xor
Ensure forward progress is made when a dmaengine driver is unable to
allocate an xor descriptor by breaking the dependency chain with
async_tx_quisce() and issue any pending descriptors.
Tested with iop-adma by setting device->max_xor = 2 to force multiple
calls to device_prep_dma_xor for each call to async_xor and limiting the
descriptor slot pool to 5. Discovered that the minimum descriptor pool
size for iop-adma is 2 * iop_chan_xor_slot_cnt(device->max_xor) + 1.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Thu, 17 Jul 2008 02:44:56 +0000 (19:44 -0700)]
async_tx: ensure the xor destination buffer remains dma-mapped
When the number of source buffers for an xor operation exceeds the hardware
channel maximum async_xor creates a chain of dependent operations. The result
of one operation is reused as an input to the next to continue the xor
calculation. The destination buffer should remain mapped for the duration of
the entire chain. To provide this guarantee the code must no longer be allowed
to fallback to the synchronous path as this will preclude the buffer from being
unmapped, i.e. the dma-driver will potentially miss the descriptor with
!DMA_COMPL_SKIP_DEST_UNMAP.
Cc: Neil Brown <neilb@suse.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dmaengine: Driver for the Synopsys DesignWare DMA controller
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds the necessary interfaces to the DMA Engine framework
to use functionality found on most embedded DMA controllers: DMA from
and to I/O registers with hardware handshaking.
In this context, hardware hanshaking means that the peripheral that
owns the I/O registers in question is able to tell the DMA controller
when more data is available for reading, or when there is room for
more data to be written. This usually happens internally on the chip,
but these signals may also be exported outside the chip for things
like IDE DMA, etc.
A new struct dma_slave is introduced. This contains information that
the DMA engine driver needs to set up slave transfers to and from a
slave device. Most engines supporting DMA slave transfers will want to
extend this structure with controller-specific parameters. This
additional information is usually passed from the platform/board code
through the client driver.
A "slave" pointer is added to the dma_client struct. This must point
to a valid dma_slave structure iff the DMA_SLAVE capability is
requested. The DMA engine driver may use this information in its
device_alloc_chan_resources hook to configure the DMA controller for
slave transfers from and to the given slave device.
A new operation for preparing slave DMA transfers is added to struct
dma_device. This takes a scatterlist and returns a single descriptor
representing the whole transfer.
Another new operation for terminating all pending transfers is added as
well. The latter is needed because there may be errors outside the scope
of the DMA Engine framework that may require DMA operations to be
terminated prematurely.
DMA Engine drivers may extend the dma_device, dma_chan and/or
dma_slave_descriptor structures to allow controller-specific
operations. The client driver can detect such extensions by looking at
the DMA Engine's struct device, or it can request a specific DMA
Engine device by setting the dma_dev field in struct dma_slave.
dmaslave interface changes since v4:
* Fix checkpatch errors
* Fix changelog (there are no slave descriptors anymore)
dmaslave interface changes since v3:
* Use dma_data_direction instead of a new enum
* Submit slave transfers as scatterlists
* Remove the DMA slave descriptor struct
dmaslave interface changes since v2:
* Add a dma_dev field to struct dma_slave. If set, the client can
only be bound to the DMA controller that corresponds to this
device. This allows controller-specific extensions of the
dma_slave structure; if the device matches, the controller may
safely assume its extensions are present.
* Move reg_width into struct dma_slave as there are currently no
users that need to be able to set the width on a per-transfer
basis.
dmaslave interface changes since v1:
* Drop the set_direction and set_width descriptor hooks. Pass the
direction and width to the prep function instead.
* Declare a dma_slave struct with fixed information about a slave,
i.e. register addresses, handshake interfaces and such.
* Add pointer to a dma_slave struct to dma_client. Can be NULL if
the DMA_SLAVE capability isn't requested.
* Drop the set_slave device hook since the alloc_chan_resources hook
now has enough information to set up the channel for slave
transfers.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 4 Jul 2008 07:13:40 +0000 (00:13 -0700)]
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
In some cases client code may need the dma-driver to skip the unmap of source
and/or destination buffers. Setting these flags indicates to the driver to
skip the unmap step. In this regard async_xor is currently broken in that it
allows the destination buffer to be unmapped while an operation is still in
progress, i.e. when the number of sources exceeds the hardware channel's
maximum (fixed in a subsequent patch).
Acked-by: Saeed Bishara <saeed@marvell.com> Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dmaengine: Add dma_client parameter to device_alloc_chan_resources
A DMA controller capable of doing slave transfers may need to know a
few things about the slave when preparing the channel. We don't want
to add this information to struct dma_channel since the channel hasn't
yet been bound to a client at this point.
Instead, pass a reference to the client requesting the channel to the
driver's device_alloc_chan_resources hook so that it can pick the
necessary information from the dma_client struct by itself.
[dan.j.williams@intel.com: fixed up fsldma and mv_xor] Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.
The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.
Changes since v2:
* Support testing multiple channels at the same time
* Support testing with multiple threads competing for the same channel
* Use counting test patterns in order to catch byte ordering issues
Changes since v1:
* Remove extra dashes around "help"
* Remove "default n" from Kconfig
* Turn TEST_BUF_SIZE into a module parameter
* Return DMA_NAK instead of DMA_DUP
* Print unhandled events
* Support testing specific channels and devices
* Move to the end of the Makefile
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dmaengine: DMA engine driver for Marvell XOR engine
The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.
This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset
The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module. In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.
When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.
Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Nicolas Pitre <nico@marvell.com> Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Kay Sievers [Tue, 8 Jul 2008 18:58:28 +0000 (11:58 -0700)]
iop-adma: fix platform driver hotplug/coldplug
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.
Cc: <stable@kernel.org> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Tue, 8 Jul 2008 18:58:21 +0000 (11:58 -0700)]
dmaengine: track the number of clients using a channel
Haavard's dma-slave interface would like to test for exclusive access to a
channel. The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.
This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Fri, 27 Jun 2008 08:21:11 +0000 (01:21 -0700)]
dmaengine: remove arch dependency from DMADEVICES
The dependency is redundant since all drivers set their specific arch
dependencies. The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect. HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.
Acked-by: Adrian Bunk <bunk@kernel.org> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This doesn't work if SLAB is selected and slab debugging is enabled as
these are passed to the preprocessor, and the preprocessor doesn't
understand sizeof.
Linus Torvalds [Wed, 28 May 2008 15:00:51 +0000 (08:00 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: fix RCU problem in cfq_cic_lookup()
block: make blktrace use per-cpu buffers for message notes
Added in elevator switch message to blktrace stream
Added in MESSAGE notes for blktraces
block: reorder cfq_queue to save space on 64bit builds
block: Move the second call to get_request to the end of the loop
splice: handle try_to_release_page() failure
splice: fix sendfile() issue with relay
David Howells [Wed, 28 May 2008 14:36:34 +0000 (15:36 +0100)]
FRV: Specify the minimum slab/kmalloc alignment
Specify the minimum slab/kmalloc alignment to be 8 bytes. This fixes a
crash when SLOB is selected as the memory allocator. The FRV arch needs
this so that it can use the load- and store-double instructions without
faulting. By default SLOB sets the minimum to be 4 bytes.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Axboe [Wed, 28 May 2008 12:45:33 +0000 (14:45 +0200)]
block: make blktrace use per-cpu buffers for message notes
Currently it uses a single static char array, but that risks
being corrupted when multiple users issue message notes at the
same time. Make the buffers dynamically allocated when the trace
is setup and make them per-cpu instead.
The default max message size of 1k is also very large, the
interface is mainly for small text notes. So shrink it to 128 bytes.
Zhang, Yanmin [Thu, 22 May 2008 13:13:29 +0000 (15:13 +0200)]
block: Move the second call to get_request to the end of the loop
In function get_request_wait, the second call to get_request could be
moved to the end of the while loop, because if the first call to
get_request fails, the second call will fail without sleep.
Linus Torvalds [Wed, 28 May 2008 01:47:59 +0000 (18:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
pciehp: add message about pciehp_slot_with_bus option
pci hotplug core: add check of duplicate slot name
pciehp: move msleep after power off
pciehp: poll cmd completion if hotplug interrupt is disabled
pciehp: fix slow probing
pciehp: fix NULL dereference in interrupt handler
shpchp: add message about shpchp_slot_with_bus option
PCI: don't enable ASPM on devices with mixed PCIe/PCI functions
Kenji Kaneshige [Tue, 27 May 2008 10:07:33 +0000 (19:07 +0900)]
pciehp: add message about pciehp_slot_with_bus option
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Kenji Kaneshige [Tue, 27 May 2008 10:07:01 +0000 (19:07 +0900)]
pci hotplug core: add check of duplicate slot name
Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3 #1
[<c0266980>] kobject_add_internal+0x140/0x190
[<c0266afd>] kobject_init_and_add+0x2d/0x40
[<c027bc91>] pci_hp_register+0x81/0x2f0
[<c027fd07>] pciehp_probe+0x1a7/0x470
[<c01b3b84>] sysfs_add_one+0x44/0xa0
[<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
[<c01b497a>] sysfs_create_link+0x8a/0xf0
[<c0279570>] pcie_port_probe_service+0x50/0x80
[<c02e0545>] driver_sysfs_add+0x55/0x70
[<c02e0662>] driver_probe_device+0x82/0x180
[<c02e07cc>] __driver_attach+0x6c/0x70
[<c02dfe0a>] bus_for_each_dev+0x3a/0x60
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e04e6>] driver_attach+0x16/0x20
[<c02e0760>] __driver_attach+0x0/0x70
[<c02e0341>] bus_add_driver+0x1a1/0x220
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e09cd>] driver_register+0x4d/0x120
[<c05db050>] ibm_acpiphp_init+0x0/0x190
[<c0125aab>] printk+0x1b/0x20
[<c05db2d0>] pcied_init+0x0/0x80
[<c05db2de>] pcied_init+0xe/0x80
[<c05c751a>] kernel_init+0x10a/0x300
[<c0120138>] schedule_tail+0x18/0x50
[<c0103b9a>] ret_from_fork+0x6/0x1c
[<c05c7410>] kernel_init+0x0/0x300
[<c05c7410>] kernel_init+0x0/0x300
[<c010485b>] kernel_thread_helper+0x7/0x1c
=======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22
Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Kenji Kaneshige [Tue, 27 May 2008 10:06:22 +0000 (19:06 +0900)]
pciehp: move msleep after power off
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Kenji Kaneshige [Tue, 27 May 2008 10:05:26 +0000 (19:05 +0900)]
pciehp: poll cmd completion if hotplug interrupt is disabled
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Kenji Kaneshige [Tue, 27 May 2008 10:04:30 +0000 (19:04 +0900)]
pciehp: fix slow probing
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit c27fb883dffe11aa4cb35ecea1fa1832ba45d4da that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:
This patch contains the following two fixes.
(1) Clear all events bits in Slot Status register to prevent the pciehp
driver from detecting the spurious events that would have been occur
before pciehp loading.
(2) Add check whether slot initialization had been already done.
This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Kenji Kaneshige [Tue, 27 May 2008 10:08:23 +0000 (19:08 +0900)]
shpchp: add message about shpchp_slot_with_bus option
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
avr32: Fix cpufreq oops when ondemand governor is default
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Oleg Nesterov [Mon, 26 May 2008 16:55:42 +0000 (20:55 +0400)]
posix timers: discard SI_TIMER signals on exec
Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.
As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460
Oleg Nesterov [Mon, 26 May 2008 16:55:42 +0000 (20:55 +0400)]
posix timers: sigqueue_free: don't free sigqueue if it is queued
Currently sigqueue_free() removes sigqueue from list, but doesn't cancel the
pending signal. This is not consistent, the task should either receive the
"full" signal along with siginfo_t, or it shouldn't receive the signal at all.
Change sigqueue_free() to clear SIGQUEUE_PREALLOC but leave sigqueue on list
if it is queued.
This is a user-visible change. If the signal is blocked, it stays queued
after sys_timer_delete() until unblocked with the "stale" si_code/si_value,
and of course it is still counted wrt RLIMIT_SIGPENDING which also limits
the number of posix timers.
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
sh: Drop broken URAM support on SH7723.
sh: update Migo-R defconfig
sh: use sm501 8250 mfd support on r2d boards
sh: add probe support for new sh7723 cut
sh: fix VPU interrupt vector for sh7723
sh: fix USBF resource for sh7722
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
vlan: Use bitmask of feature flags instead of seperate feature bits
fmvj18x_cs: add NextCom NC5310 rev B support
xirc2ps_cs: re-initialize the multicast address in do_reset
3C509: rx_bytes should not be increased when alloc_skb failed
NETFRONT: Use __skb_queue_purge()
VIRTIO: Use __skb_queue_purge()
phylib: do EXPORT_SYMBOL on get_phy_id
netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
WAN: protect HDLC proto list while insmod/rmmod
drivers/net/fs_enet: remove null pointer dereference
S2io: Version update for napi and MSI-X patches
S2io: Added napi support when MSIX is enabled.
S2io: Move all the transmit completions to a single msi-x (alarm) vector
drivers/net/ehea - remove unnecessary memset after kzalloc
au1000_eth: remove useless check
Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
cpmac bugfixes and enhancements
e1000e: use resource_size_t, not unsigned long, for phys addrs
net/usb: add support for Apple USB Ethernet Adapter
uli526x: add support for netpoll
...
Michael Krufky [Mon, 26 May 2008 14:08:40 +0000 (16:08 +0200)]
tuner: Do not alter i2c_client.name
The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
Kconfig: introduce ARCH_DEFCONFIG to DEFCONFIG_LIST
.gitignore: match ncscope.out
scripts/ver_linux use 'gcc -dumpversion'
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Add ICH9DO into the iTCO_wdt.c driver
[WATCHDOG] Fix booke_wdt.c on MPC85xx SMP system's
[WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
[WATCHDOG] hpwdt: Fix NMI handling.
[WATCHDOG] Blackfin Watchdog Driver: split platform device/driver
[WATCHDOG] Add w83697h_wdt early_disable option
[WATCHDOG] Make w83697h_wdt timeout option string similar to others
[WATCHDOG] Make w83697h_wdt void-like functions void
Linus Torvalds [Sun, 25 May 2008 21:59:27 +0000 (14:59 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
[ALSA] hda - Fix capture mute Widget for stac9250/9251
[ALSA] snd-pcsp - fix pcsp_treble_info() to honour an item number
[ALSA] hda - Added support for Foxconn P35AX-S mainboard
[ALSA] hda - Fix COEF and EAPD in ALC889 auto-configuration mode
[ALSA] hda - Fix noise on VT1708 codec
[ALSA] hda - Add model for ASUS P5K-E/WIFI-AP
Sam Ravnborg [Sun, 25 May 2008 21:03:18 +0000 (23:03 +0200)]
Kconfig: introduce ARCH_DEFCONFIG to DEFCONFIG_LIST
init/Kconfig contains a list of configs that are searched
for if 'make *config' are used with no .config present.
Extend this list to look at the config identified by
ARCH_DEFCONFIG.
With this change we now try the defconfig targets last.
This fixes a regression reported
by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com>
Jike Song [Thu, 22 May 2008 01:23:10 +0000 (09:23 +0800)]
.gitignore: match ncscope.out
Sometimes I got this:
$ git-status
{snip}
# On branch master
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# ncscope.out
nothing added to commit but untracked files present (use "git add"
to track)
Fix it.
Signed-off-by: Jike Song <albcamus@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Gabriel C [Wed, 21 May 2008 18:36:19 +0000 (20:36 +0200)]
scripts/ver_linux use 'gcc -dumpversion'
These magic greps and hacks in ver_linux to get the gcc version always break after some gcc releases.
Since now gcc >4.3 allows compiling with '--with-pkgversion' ( which can be everything 'My Cool Gcc' or something )
ver_linux will report random junk for these.
Simply use 'gcc -dumpversion' to get the gcc version which should always work.
Signed-off-by: Gabriel C <nix.or.die@googlemail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Gabriel C [Wed, 30 Apr 2008 14:51:10 +0000 (16:51 +0200)]
[WATCHDOG] Add ICH9DO into the iTCO_wdt.c driver
Add the Intel ICH9DO controller ID's for the iTCO_wdt kernel driver and bump
the driver version.
Tested on an P5E-VM DO ASUS motherboard.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Chen Gong [Tue, 29 Apr 2008 08:42:05 +0000 (16:42 +0800)]
[WATCHDOG] Fix booke_wdt.c on MPC85xx SMP system's
On Book-E SMP systems each core has its own private watchdog. If only one
watchdog is enabled, when the core that doesn't enable the watchdog is hung,
system can't reset because no watchdog is running on it. That's bad. It
means we must enable watchdogs on both cores.
We can use smp_call_function() to send appropriate messages to all the other
cores to enable and update the watchdog.
Signed-off-by: Chen Gong <g.chen@freescale.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Jordan Crouse [Mon, 21 Jan 2008 17:07:00 +0000 (10:07 -0700)]
[WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
Add a watchdog timer based on the MFGPT timers in the CS5535/CS5536
companion chips to the AMD Geode GX and LX processors. Only caveat
is that the BIOS must provide at least a one free timer, and most
do not.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I need to just return in case it's not my NMI so someone else can take a look
at it (and reset die_nmi_called to 0 in case I actually do get one that's mine
to handle).
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
- split platform device/driver registering from actual watchdog device/driver
registering so that we can cleanly load/unload
- fixup __initdata with __initconst and __devinitdata with __devinitconst
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Samuel Tardieu [Wed, 12 Mar 2008 13:28:03 +0000 (14:28 +0100)]
[WATCHDOG] Add w83697h_wdt early_disable option
Pádraig Brady requested the possibility of not disabling the watchdog
at module load time or kernel boot time if it had been previously enabled
in the bios. It may help rebooting the machine if it freezes before the
userland daemon kicks in.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net> Cc: Pádraig Brady <P@draigBrady.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Sat, 24 May 2008 17:20:00 +0000 (10:20 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: prevent PGE flush from interruption/preemption
x86: use explicit copy in vdso_gettimeofday()
namespacecheck: automated fixes
x86/xen: fix arbitrary_virt_to_machine()
x86: don't read maxlvt before checking if APIC is mapped
x86: disable TSC for sched_clock() when calibration failed
x86: distangle user disabled TSC from unstable
x86: fix setup of cyc2ns in tsc_64.c
David Brownell [Fri, 23 May 2008 20:05:03 +0000 (13:05 -0700)]
spi: remove some spidev oops-on-rmmod paths
Somehow the spidev code forgot to include a critical mechanism: when the
underlying device is removed (e.g. spi_master rmmod), open file
descriptors must be prevented from issuing new I/O requests to that
device. On penalty of the oopsing reported by Sebastian Siewior
<bigeasy@tglx.de> ...
This is a partial fix, adding handshaking between the lower level (SPI
messaging) and the file operations using the spi_dev. (It also fixes an
issue where reads and writes didn't return the number of bytes sent or
received.)
There's still a refcounting issue to be addressed (separately).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Reported-by: Sebastian Siewior <bigeasy@tglx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cedric Le Goater [Fri, 23 May 2008 20:05:02 +0000 (13:05 -0700)]
cgroups: remove node_ prefix_from ns subsystem
This is a slight change in the namespace cgroup subsystem api.
The change is that previously when cgroup_clone() was called (currently
only from the unshare path in ns_proxy cgroup, you'd get a new group named
"node_$pid" whereas now you'll get a group named after just your pid.)
The only users who would notice it are those who are using the ns_proxy
cgroup subsystem to auto-create cgroups when namespaces are unshared -
something of an experimental feature, which I think really needs more
complete container/namespace support in order to be useful. I suspect the
only users are Cedric and Serge, or maybe a few others on
containers@lists.linux-foundation.org. And in fact it would only be
noticed by the users who make the assumption about how the name is
generated, rather than getting it from the /proc/<pid>/cgroups file for
the process in question.
Whether the change is actually needed or not I'm fairly agnostic on, but I
guess it is more elegant to just use the pid as the new group name rather
than adding a fairly arbitrary "node_" prefix on the front.
[menage@google.com: provided changelog] Signed-off-by: Cedric Le Goater <clg@fr.ibm.com> Cc: "Paul Menage" <menage@google.com> Cc: "Serge E. Hallyn" <serue@us.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for_each_pgdat() was renamed to for_each_online_pgdat() and kerneldoc
comments should be updated accordingly.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shi Weihua [Fri, 23 May 2008 20:04:59 +0000 (13:04 -0700)]
sys_prctl(): fix return of uninitialized value
If none of the switch cases match, the PR_SET_PDEATHSIG and
PR_SET_DUMPABLE cases of the switch statement will never write to local
variable `error'.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Cc: Andrew G. Morgan <morgan@kernel.org> Acked-by: "Serge E. Hallyn" <serue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Fri, 23 May 2008 20:04:57 +0000 (13:04 -0700)]
S3C2410: fix driver MODULE_ALIAS()
Add a correct MODULE_ALIAS() entry for this driver to enable udev module
loading.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Fri, 23 May 2008 20:04:56 +0000 (13:04 -0700)]
S3C2410: clean out changelog header and tidy
Remove the old changelog entries which are now out of date and should be
extractable from git anyway. Also tidy up the copyright for the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Fri, 23 May 2008 20:04:56 +0000 (13:04 -0700)]
S3C2410: add error print if we cannot add attribute
Fix the following warning by checking the result of device_create_file and
printing an error but not removing the device (loss of debug registers is
not fatal).
drivers/video/s3c2410fb.c:905: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Fri, 23 May 2008 20:04:55 +0000 (13:04 -0700)]
S3C2410: ensure that FB_BLANK_POWERDOWN shuts down the controller
When a blank level of FB_BLANK_POWERDOWN is used, we should shut down the
controller so that it no longer tries to produce any panel signals or
data, and shuts down the DMA which is not needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Fri, 23 May 2008 20:04:53 +0000 (13:04 -0700)]
SM501: reverse FPEN/VBIASEN flags behaviour
To keep backwards compatibility, reverse the meanings of these flags so
that when they are not set, the driver uses the original behvaiour.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This occurs when we are scanning the zonelists looking for a ZONE_NORMAL
page. In this system there is only ZONE_DMA and ZONE_NORMAL memory on
node 0, all other nodes are mapped above 4GB physical. Here is a dump
of the zonelists from this system:
When performing a node local allocation we call get_page_from_freelist()
looking for a page. It in turn calls first_zones_zonelist() which returns
a preferred_zone. Where there are no applicable zones this will be NULL.
However we use this unconditionally, leading to this panic.
Where there are no applicable zones there is no possibility of a successful
allocation, so simply fail the allocation.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Fri, 23 May 2008 20:04:49 +0000 (13:04 -0700)]
serial: fix enable_irq_wake/disable_irq_wake imbalance in serial_core.c
enable_irq_wake() and disable_irq_wake() need to be balanced. However,
serial_core.c calls these for different conditions during the suspend and
resume functions...
This is causing a regular WARN_ON() as found at
http://www.kerneloops.org/search.php?search=set_irq_wake
This patch makes the conditions for triggering the _wake enable/disable
sequence identical.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Denis V. Lunev [Fri, 23 May 2008 20:04:47 +0000 (13:04 -0700)]
proc: proc_get_inode() should get module only once
Any file under /proc/net opened more than once leaked the refcounter
on the module it belongs to.
The problem is that module_get is called for each file opening while
module_put is called only when /proc inode is destroyed. So, lets put
module counter if we are dealing with already initialised inode.
Signed-off-by: Denis V. Lunev <den@openvz.org> Cc: David Miller <davem@davemloft.net> Cc: Patrick McHardy <kaber@trash.net> Acked-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Robert Olsson <robert.olsson@its.uu.se> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Reported-by: Roland Kletzing <devzero@web.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcin Krol [Fri, 23 May 2008 20:04:46 +0000 (13:04 -0700)]
brd: don't show ramdisks in /proc/partitions
In 2.6.25, ramdisk devices show up in /proc/partitions, which is a
behaviour change from the old rd.c. Add GENHD_FL_SUPPRESS_PARTITION_INFO,
which was present in rd.c.
All kernels prior to 2.6.25 weren't displaying ramdisks in
/proc/partitions. Since there are many userspace tools using information
from /proc/partitions some of them may now behave incorrectly (I didn't
tested any though). For example before 2.6.25 /proc/partitions was empty
if no block devices like hard disks and such were detected by kernel. Now
all 16 ramdisks are always visible there. Some software may rely on such
information (I mean, on empty /proc/partitions).
There was quite similar situation back in 2004, and ramdisks were excluded
back from displaying. Thats why I called this a regression (maybe a bit
unfortunate). See this patch for info:
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.3-rc2/2.6.3-rc2-mm1/broken-out/nbd-proc-partitions-fix.patch
I also think that someone somewhere (long time ago) excluded ramdisks from
/proc/partitions for good reasons. It is possible that now such new
"feature" is harmless, but I think there are more chances that someone
will say "hey, /proc/partitions has changed, now my software doesn't work"
then "hey where did my new 2.6.25 feature go". nbd devices are also
excluded, maybe for very same (unknown to me) reasons.
Signed-off-by: Marcin Krol <hawk@pld-linux.org> Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log