Stefan Richter [Sun, 24 Feb 2008 17:57:23 +0000 (18:57 +0100)]
firewire: potentially invalid pointers used in fw_card_bm_work
The bus management workqueue job was in danger to dereference NULL
pointers. Also, after having temporarily lifted card->lock, a few node
pointers and a device pointer may have become invalid.
Add NULL pointer checks and get the necessary references. Also, move
card->local_node out of fw_card_bm_work's sight during shutdown of the
card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Stefan Richter [Tue, 26 Feb 2008 22:30:02 +0000 (23:30 +0100)]
firewire: fw-sbp2: better fix for NULL pointer dereference in scsi_remove_device
Patch "firewire: fw-sbp2: fix NULL pointer deref. in scsi_remove_device"
had the unintended effect that firewire-sbp2 could not be unloaded
anymore until all SBP-2 devices were unplugged.
We now fix the NULL pointer bug by reacquiring a reference to the sdev
instead of holding a reference to the sdev (and to the module) all the
time.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Jarod Wilson <jwilson@redhat.com>
Linus Torvalds [Sat, 1 Mar 2008 00:54:33 +0000 (16:54 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] wrap kmap_atomic(KM_IRQ0) with local_irq_save/restore()
sata_svw: Add support for HT1100 SATA controller
Jeff Garzik [Sat, 1 Mar 2008 00:10:51 +0000 (19:10 -0500)]
[libata] wrap kmap_atomic(KM_IRQ0) with local_irq_save/restore()
Interrupts must be disabled if using kmap_atomic(KM_IRQ0), but that was
not the case in a few code paths coming directly from ATA driver
interrupt handlers (which use spin_lock rather than spin_lock_irqsave).
Mark Brown [Wed, 27 Feb 2008 14:34:56 +0000 (15:34 +0100)]
[ARM] 4843/1: Add GCR_CLKBPB for PXA3xx
The PXA3xx AC97 controller has an additional control bit GCR_CLKBPB
which must be used during cold reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alexandre Rusev [Tue, 26 Feb 2008 17:42:10 +0000 (18:42 +0100)]
[ARM] 4839/1: fixes kernel Oops in /dev/mem device driver for memory map with PHYS_OFF
"cat /dev/mem" may cause kernel Oops for boards with PHYS_OFFSET != 0
because character device is mapped to addresses starting from zero
and there is no protection against such situation.
Patch just add this.
Signed-off-by: Alexandre Rusev <arusev@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Kunze [Sun, 24 Feb 2008 16:59:34 +0000 (17:59 +0100)]
[ARM] 4838/1: Fix kexec for SA1100 machines
This patch sets KEXEC_CONTROL_MEMORY_LIMIT to (-1)UL. As the value is
compared with physical addresses TASK_SIZE makes no sense. Machines
where the RAM addresses start above TASK_SIZE kexecs eats all memory
and crashes the kernel without this patch.
Signed-off-by: Thomas Kunze <thommycheck@gmx.de> Acked-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 4837/1: make __get_unaligned_*() return unsigned types
Eric Sandeen tracked an XFS on ARM corruption bug down to a function
under fs/xfs/ involving some get_unaligned() calls on u64 pointers.
As it turns out, calling ARM's get_unaligned() on a u64 pointer
pointing to the following byte sequence:
80 81 82 83 84 85 86 87
would return ffffffff83828180 (LE mode.) This turns out to be
because of implicit u8 -> int promotion in ARM's implementation of
various helpers for get_unaligned(), causing them to accidentally
return signed instead of unsigned values, which in turn caused the
subsequent casts to unsigned long long in __get_unaligned_8_[bl]e()
to sign-extend the lower words.
Fix by casting the return values of __get_unaligned_[24]_[bl]e()
to unsigned int.
Cc: Eric Sandeen <sandeen@sandeen.net> Cc: Rabeeh Khoury <rabeeh@marvell.com> Cc: Nicolas Pitre <nico@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Uli Luckas [Fri, 22 Feb 2008 15:45:18 +0000 (16:45 +0100)]
[ARM] 4836/1: Make ATAGS_PROC depend on KEXEC
On Wed, Feb 20, 2008 at 11:50:33AM +0100, Guennadi Liakhovetski wrote:
> arch/arm/kernel/atags.c uses for some reason the
> KEXEC_BOOT_PARAMS_SIZE macro, which is only defined if CONFIG_KEXEC
> is set. So, either this macro should be defined always, or another
> macro should be used, or ATAGS_PROC should depend on KEXEC.
As the procfs export of ATAGS is not meant as a stable, general purpose
ABI it shouldn't be an independent, general configuration option.
This patch make ATAGS_PROC depend on KEXEC
Signed-off-by: Uli Luckas <u.luckas@road.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul E. McKenney [Thu, 28 Feb 2008 19:51:07 +0000 (11:51 -0800)]
rcupreempt: remove never-migrates assumption from rcu_process_callbacks()
This patch fixes a potentially invalid access to a per-CPU variable in
rcu_process_callbacks().
This per-CPU access needs to be done in such a way as to guarantee that
the code using it cannot move to some other CPU before all uses of the
value accessed have completed. Even though this code is currently only
invoked from softirq context, which currrently cannot migrate to some
other CPU, life would be better if this code did not silently make such
an assumption.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Paul E. McKenney [Thu, 28 Feb 2008 00:21:10 +0000 (16:21 -0800)]
rcupreempt: fix hibernate/resume in presence of PREEMPT_RCU and hotplug
This fixes a oops encountered when doing hibernate/resume in presence of
PREEMPT_RCU.
The problem was that the code failed to disable preemption when
accessing a per-CPU variable. This is OK when called from code that
already has preemption disabled, but such is not the case from the
suspend/resume code path.
Reported-by: Dave Young <hidave.darkstar@gmail.com> Tested-by: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
softlockup: fix task state setting
rcu: add support for dynamic ticks and preempt rcu
Dave Anderson [Thu, 21 Feb 2008 16:45:38 +0000 (11:45 -0500)]
x86 ptrace: fix ptrace_bts_config structure declaration
The 2.6.25 ptrace_bts_config structure in asm-x86/ptrace-abi.h
is defined with u32 types:
#include <asm/types.h>
/* configuration/status structure used in PTRACE_BTS_CONFIG and
PTRACE_BTS_STATUS commands.
*/
struct ptrace_bts_config {
/* requested or actual size of BTS buffer in bytes */
u32 size;
/* bitmask of below flags */
u32 flags;
/* buffer overflow signal */
u32 signal;
/* actual size of bts_struct in bytes */
u32 bts_size;
};
#endif
But u32 is only accessible in asm-x86/types.h if __KERNEL__,
leading to compile errors when ptrace.h is included from
user-space. The double-underscore versions that are exported
to user-space in asm-x86/types.h should be used instead.
Signed-off-by: Dave Anderson <anderson@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Sat, 23 Feb 2008 19:43:21 +0000 (20:43 +0100)]
x86: CPA: avoid split of alias mappings
avoid over-eager large page splitup.
When the target area needs to be split or is split already (ioremap)
then the current code enforces the split of large mappings in the alias
regions even if we could avoid it.
Use a separate variable processed in the cpa_data structure to carry
the number of pages which have been processed instead of reusing the
numpages variable. This keeps numpages intact and gives the alias code
a chance to keep large mappings intact.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Roland McGrath [Wed, 27 Feb 2008 19:42:15 +0000 (11:42 -0800)]
x86 vdso: fix build locale dependency
Priit Laes discovered that the sed command processing nm output was
sensitive to locale settings. This was addressed in commit 03994f01e8b72b3d01fd3d09d1cc7c9f421a727c by using [:alnum:] in place of
[a-zA-Z0-9].
But that solution too is locale-dependent and may not always match
the identifiers it needs to. The better fix is just to run sed et al
with a fixed locale setting in all builds.
Signed-off-by: Roland McGrath <roland@redhat.com> CC: Priit Laes <plaes@plaes.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hans Rosenfeld [Mon, 18 Feb 2008 17:10:47 +0000 (18:10 +0100)]
x86: fix pmd_bad and pud_bad to support huge pages
I recently stumbled upon a problem in the support for huge pages. If a
program using huge pages does not explicitly unmap them, they remain
mapped (and therefore, are lost) after the program exits.
I observed that the free huge page count in /proc/meminfo decreased when
running my program, and it did not increase after the program exited.
After running the program a few times, no more huge pages could be
allocated.
The reason for this seems to be that the x86 pmd_bad and pud_bad
consider pmd/pud entries having the PSE bit set invalid. I think there
is nothing wrong with this bit being set, it just indicates that the
lowest level of translation has been reached. This bit has to be (and
is) checked after the basic validity of the entry has been checked, like
in this fragment from follow_page() in mm/memory.c:
if (pmd_none(*pmd) || unlikely(pmd_bad(*pmd)))
goto no_page_table;
Note that this code currently doesn't work as intended if the pmd refers
to a huge page, the pmd_huge() check can not be reached if the page is
huge.
Extending pmd_bad() (and, for future 1GB page support, pud_bad()) to
allow for the PSE bit being set fixes this. For similar reasons,
allowing the NX bit being set is necessary, too. I have seen huge pages
having the NX bit set in their pmd entry, which would cause the same
problem.
Signed-Off-By: Hans Rosenfeld <hans.rosenfeld@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Roland McGrath [Tue, 26 Feb 2008 21:00:18 +0000 (13:00 -0800)]
x86: tls prevent_tail_call
Fix a kernel bug (vmware boot problem) reported by Tomasz Grobelny,
which occurs with certain .config variants and gccs.
The x86 TLS cleanup in commit efd1ca52d04d2f6df337a3332cee56cd60e6d4c4
made the sys_set_thread_area and sys_get_thread_area functions ripe for
tail call optimization. If the compiler chooses to use it for them, it
can clobber the user trap frame because these are asmlinkage functions.
Reported-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net> Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Steven Rostedt [Fri, 29 Feb 2008 17:46:50 +0000 (18:46 +0100)]
rcu: add support for dynamic ticks and preempt rcu
The PREEMPT-RCU can get stuck if a CPU goes idle and NO_HZ is set. The
idle CPU will not progress the RCU through its grace period and a
synchronize_rcu my get stuck. Without this patch I have a box that will
not boot when PREEMPT_RCU and NO_HZ are set. That same box boots fine
with this patch.
This patch comes from the -rt kernel where it has been tested for
several months.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Fri, 29 Feb 2008 16:41:13 +0000 (08:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
serial: Move asm-sh/sci.h to linux/serial_sci.h.
sh: Fix up HAS_SR_RB typo in entry-macros.
maple: fix device detection
sh: fix rtc_resources setup for sh770x
sh: heartbeat: ioremap is expected to succeed
sh: Storage class should be before const qualifier
maple: remove unused variable
sh: SH5-103 needs to select CPU_SH5.
sh: Rename SH-3 CCR3 reg to avoid synclink_cs clash.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (79 commits)
[X25]: Use proc_create() to setup ->proc_fops first
[WANROUTER]: Use proc_create() to setup ->proc_fops first
[8021Q]: Use proc_create() to setup ->proc_fops first
[IPV4]: Use proc_create() to setup ->proc_fops first
[IPV6]: Use proc_create() to setup ->proc_fops first
[SCTP]: Use proc_create() to setup ->proc_fops first
[PKTGEN]: Use proc_create() to setup ->proc_fops first
[NEIGHBOUR]: Use proc_create() to setup ->proc_fops first
[LLC]: Use proc_create() to setup ->proc_fops first
[IPX]: Use proc_create() to setup ->proc_fops first
[SUNRPC]: Use proc_create() to setup ->proc_fops first
[ATM]: Use proc_create() to setup ->proc_fops first
[SCTP]: Update AUTH structures to match declarations in draft-16.
[SCTP]: Incorrect length was used in SCTP_*_AUTH_CHUNKS socket option
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
[APPLETALK]: Use proc_create() to setup ->proc_fops first
[BNX2X]: add bnx2x to MAINTAINERS
[BNX2X]: update version, remove CVS strings
[BNX2X]: Fix Xmit bugs
[BNX2X]: Prevent PCI queue overflow
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Adjust kernel PC validation test in fault handler.
[SPARC64]: Loosen checks in exception table handling.
[SPARC64]: Fix section mismatch from kernel_map_range
[SPARC64]: Fix section mismatchs from dr_cpu_data
[SPARC]: Fix build in arch/sparc/kernel/led.c
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove stale comments from ide-dma.c (take 2)
ide: remove ide-tape documentation from Documentation/ide.txt
qd65xx: remove commented out code
ide-tape: schedule driver for removal after 6 months
ide-disk: add missing printk() KERN_* levels
ide: fix sparse warning about shadowing 'flags' symbol
ide-cd: fix CD/DVD burning
ide-cd: fix 'ireason' handling for REQ_TYPE_ATA_PC requests
qd65xx: fix setup of QD6580 Control register
ide: skip probing port if "hdx=noprobe" was used for both devices on it
ide: remove redundant comment from ide_unregister()
hpt366: fix section mismatch warnings
ide-cd: Enable audio play quirk for Optiarc DVD RW AD-5200A drive
David Howells [Thu, 28 Feb 2008 13:29:43 +0000 (13:29 +0000)]
Fix hpet_(un)register_irq_handler() for emulation
Fix hpet_(un)register_irq_handler() for when CONFIG_HPET_EMULATE_RTC=n. They
are provided macros that substitute value 0, but if they are called as
functions and the return value isn't checked, the following warnings appear:
drivers/char/rtc.c: In function `rtc_init':
drivers/char/rtc.c:1063: warning: statement with no effect
drivers/char/rtc.c: In function `rtc_exit':
drivers/char/rtc.c:1157: warning: statement with no effect
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Tue, 26 Feb 2008 21:20:58 +0000 (13:20 -0800)]
elfcore-compat fix uid/gid types
I overlooked the difference between __kernel_uid_t and uid_t when defining
struct compat_elf_prpsinfo. The result is a regression in 32-bit core
dumps on x86_64, where the NT_PRPSINFO note has the wrong size and layout.
This patch fixes it.
Harvey Harrison [Fri, 29 Feb 2008 10:46:32 +0000 (11:46 +0100)]
[ALSA] sound: ice1712: unused structs
Don't need to declare a struct when defining a structure layout. Both
of these structs are unused.
sound/pci/ice1712/revo.c:39:3: warning: symbol 'revo51' was not declared. Should it be static?
sound/pci/ice1712/phase.c:54:3: warning: symbol 'phase28' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 25 Feb 2008 14:32:01 +0000 (15:32 +0100)]
[ALSA] hda-codec - Fix AD1988 capture elements
The some indices of capture elements of AD1988 are wrongly assigned.
This patch fixes it. See ALSA bug#3795
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3795
Clemens Ladisch [Mon, 25 Feb 2008 10:01:00 +0000 (11:01 +0100)]
[ALSA] usb-audio: add workaround for broken E-Mu frequency feedback
Add a workaround for the feedback pipe of E-Mu 0202/0404 USB devices
that reports the number of samples per packet instead of the number of
samples per microframe.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 18 Feb 2008 11:36:11 +0000 (12:36 +0100)]
[ALSA] hda-codec - Fix Master volume on HP dv8000
HP dv8000 laptop has a problem with Master volume. It's due to the
connection of the widget 0x13. When it's connected from the analog
amp mixer (0x19), it works as expected mysteriously (ALSA bug#3775):
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3775
Vlad Yasevich [Wed, 27 Feb 2008 21:04:52 +0000 (16:04 -0500)]
[SCTP]: Update AUTH structures to match declarations in draft-16.
The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.
Neil Horman [Fri, 15 Feb 2008 14:53:59 +0000 (09:53 -0500)]
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope. This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Herbert Xu [Thu, 28 Feb 2008 19:23:17 +0000 (11:23 -0800)]
[IPCOMP]: Disable BH on output when using shared tfm
Because we use shared tfm objects in order to conserve memory,
(each tfm requires 128K of vmalloc memory), BH needs to be turned
off on output as that can occur in process context.
Previously this was done implicitly by the xfrm output code.
That was lost when it became lockless. So we need to add the
BH disabling to IPComp directly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Zaytsev [Sat, 23 Feb 2008 10:33:07 +0000 (13:33 +0300)]
Don't build bcm43xx if SSB is static and b43 PCI-SSB bridge is enabled.
This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Zaytsev [Sat, 23 Feb 2008 09:59:26 +0000 (12:59 +0300)]
Use a separate config option for the b43 pci to ssb bridge.
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Dreier [Tue, 26 Feb 2008 14:26:56 +0000 (15:26 +0100)]
libertas: Remove unused exports
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com> Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:13 +0000 (23:15 +0100)]
rt2x00: Fix rt2x00lib_reset_link_tuner()
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:05 +0000 (23:15 +0100)]
rt2x00: Add link tuner safe RX toggle states
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:01 +0000 (23:15 +0100)]
rt2x00: Fix antenna diversity
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6-omap-h63xx.git / log