Jay Vosburgh [Mon, 15 Oct 2007 23:44:27 +0000 (16:44 -0700)]
bonding: two small fixes for IPoIB support
Two small fixes to IPoIB support for bonding:
1- copy header_ops from slave to bonding for IPoIB slaves
2- move release and destroy logic to UNREGISTER from GOING_DOWN
notifier to avoid double release
Set bonding to version 3.2.1.
Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok [Mon, 15 Oct 2007 21:30:59 +0000 (14:30 -0700)]
e1000e: don't poke PHY registers to retreive link status
Apparently poking the link status registers when autonegotiation
is running on the PHY might botch the PHY link on 80003es2lan
devices. While this is a very rare condition we can completely
avoid it alltogether by just using the MAC link bits to provide
the proper information to ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
main change:
* greatly improve per-NIC probe diagnostic output. Similar to other
net drivers, print out MAC address, PHY info, and various hardware and
software flags that may be relevant.
other changes:
* similar to other net drivers, only print the initial version message
when we have found at least one board.
* don't bother to print error message when pci_enable_device() fails,
it will do so for us.
* use dev_printk() rather than printk() in nv_probe(). This gives
use a standardized output similar to the rest of the kernel, and
eliminates the need to manually print out PCI bus id.
Linus Torvalds [Tue, 16 Oct 2007 23:52:21 +0000 (16:52 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (25 commits)
firewire: fw-cdev: reorder wakeup vs. spinlock
firewire: in-code doc updates.
firewire: a header cleanup
firewire: adopt read cycle timer ABI from raw1394
firewire: fw-ohci: check for misconfigured bus (phyID == 63)
firewire: fw-ohci: missing dma_unmap_single
firewire: fw-ohci: log posted write errors
firewire: fw-ohci: reorder includes
firewire: fw-ohci: fix includes
firewire: fw-ohci: enforce read order for selfID generation
firewire: fw-sbp2: use an own workqueue (fix system responsiveness)
firewire: fw-sbp2: expose module parameter for workarounds
firewire: fw-sbp2: add support for multiple logical units per target
firewire: fw-sbp2: always enable IRQs before calling command ORB callback
firewire: fw-core: local variable shadows a global one
firewire: optimize fw_core_add_address_handler
ieee1394: ieee1394_core.c: use DEFINE_SPINLOCK for spinlock definition
ieee1394: csr1212: proper refcounting
ieee1394: nodemgr: fix leak of struct csr1212_keyval
ieee1394: pcilynx: I2C cleanups
...
* We add ebitmap_for_each_positive_bit() which enables to walk on
any positive bit on the given ebitmap, to improve its performance
using common bit-operations defined in linux/bitops.h.
In the previous version, this logic was implemented using a combination
of ebitmap_for_each_bit() and ebitmap_node_get_bit(), but is was worse
in performance aspect.
This logic is most frequestly used to compute a new AVC entry,
so this patch can improve SELinux performance when AVC misses are happen.
* struct ebitmap_node is redefined as an array of "unsigned long", to get
suitable for using find_next_bit() which is fasted than iteration of
shift and logical operation, and to maximize memory usage allocated
from general purpose slab.
* Any ebitmap_for_each_bit() are repleced by the new implementation
in ss/service.c and ss/mls.c. Some of related implementation are
changed, however, there is no incompatibility with the previous
version.
* The width of any new line are less or equal than 80-chars.
The following benchmark shows the effect of this patch, when we
access many files which have different security context one after
another. The number is more than /selinux/avc/cache_threshold, so
any access always causes AVC misses.
Eric Paris [Fri, 21 Sep 2007 18:37:10 +0000 (14:37 -0400)]
SELinux: policy selectable handling of unknown classes and perms
Allow policy to select, in much the same way as it selects MLS support, how
the kernel should handle access decisions which contain either unknown
classes or unknown permissions in known classes. The three choices for the
policy flags are
0 - Deny unknown security access. (default)
2 - reject loading policy if it does not contain all definitions
4 - allow unknown security access
The policy's choice is exported through 2 booleans in
selinuxfs. /selinux/deny_unknown and /selinux/reject_unknown.
Signed-off-by: Eric Paris <eparis@redhat.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: James Morris <jmorris@namei.org>
It reduces the selinux overhead on read/write by only revalidating
permissions in selinux_file_permission if the task or inode labels have
changed or the policy has changed since the open-time check. A new LSM
hook, security_dentry_open, is added to capture the necessary state at open
time to allow this optimization.
Yuichi Nakamura [Fri, 24 Aug 2007 02:55:11 +0000 (11:55 +0900)]
SELinux: tune avtab to reduce memory usage
This patch reduces memory usage of SELinux by tuning avtab. Number of hash
slots in avtab was 32768. Unused slots used memory when number of rules is
fewer. This patch decides number of hash slots dynamically based on number
of rules. (chain length)^2 is also printed out in avtab_hash_eval to see
standard deviation of avtab hash table.
Signed-off-by: Yuichi Nakamura<ynakam@hitachisoft.jp> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: James Morris <jmorris@namei.org>
Stefan Richter [Sat, 29 Sep 2007 08:41:58 +0000 (10:41 +0200)]
firewire: adopt read cycle timer ABI from raw1394
This duplicates the read cycle timer feature of raw1394 (added in Linux
2.6.21) in firewire-core's userspace ABI. The argument to the ioctl is
reordered though to ensure 32/64 bit compatibility.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sat, 25 Aug 2007 12:08:19 +0000 (14:08 +0200)]
firewire: fw-ohci: enforce read order for selfID generation
It seems unlikely, but access to self_id_cpu[0] could at least in theory
be deferred until after the loop over self_id_cpu[1..n] or even after
the subsequent reg_read. Enforce the desired order by a read barrier.
Also prevent the reg_read from being reordered relative to the for loop.
This isn't necessary if the loop's conditional printk counts as an
implicit barrier, but better make it explicit.
(self_id_cpu[] is a coherent DMA buffer.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 12 Aug 2007 10:51:18 +0000 (12:51 +0200)]
firewire: fw-sbp2: use an own workqueue (fix system responsiveness)
Firewire-sbp2 did very uncooperative things in the kernel's shared
workqueue: Sleeping until reception of management status from the
target for up to 2 seconds, and performing SCSI inquiry and all of the
setup of SCSI command set drivers via scsi_add_device. If there were
transient or permanent error conditions, this caused long blockage of
the kernel's events process, noticeable e.g. by blocked keyboard input.
We now allocate a workqueue process exclusive to fw-sbp2. As a side
effect, this also increases parallelism of fw-sbp2's login and reconnect
work versus fw-core's device discovery and device update work which is
performed in the shared workqueue.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Mon, 13 Aug 2007 15:48:25 +0000 (17:48 +0200)]
firewire: fw-sbp2: expose module parameter for workarounds
On rare occasions, the ability to set one of the workaround flags at
runtime may save the day.
People who experience I/O errors with firewire-sbp2 while the old sbp2
driver worked for them should try workarounds=1 and report to the devel
mailinglist whether that improves things. Firewire-sbp2 defaults to the
SCSI stack's maximum transfer size per command, while sbp2 limits them
to 128 kBytes. Flag 1 accomplishes just that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 25 Aug 2007 08:40:42 +0000 (10:40 +0200)]
firewire: fw-sbp2: always enable IRQs before calling command ORB callback
On IOMMU-less noncoherent architectures, orb->callback will memcpy the
whole SCSI command buffer for READ-like SCSI commands. It is therefore
friendlier to enable IRQs before the call, like before patch "Add
ref-counting for sbp2 orbs".
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sat, 15 Sep 2007 12:50:25 +0000 (14:50 +0200)]
ieee1394: csr1212: proper refcounting
At least since nodemgr got rid of coarse global locking, accesses to
struct csr1212_keyval's reference counter should be atomic and coupled
with proper barriers. Also, calls to csr1212_keep_keyval(kv) should
occur before kv is being used.
(We probably should convert refcnt to struct kref, but how to keep
csr1212_destroy_keyval's implementation non-recursively then?)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 15 Sep 2007 12:45:53 +0000 (14:45 +0200)]
ieee1394: nodemgr: fix leak of struct csr1212_keyval
csr1212_keep_keyval(kv) in nodemgr_process_root_directory was
unbalanced if ne->vendor_name_kv already exists. This happens for
example if eth1394 or raw1394 modify the local config ROM and it is
parsed again.
As a bonus, the attempt to add the vendor_name_kv sysfs attribute
when it already exists is now fixed for good.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Jean Delvare [Sat, 8 Sep 2007 12:09:19 +0000 (14:09 +0200)]
ieee1394: pcilynx: I2C cleanups
* Delete optional and empty i2c client_register and client_unregister
callbacks.
* Use the proper i2c adapter ID.
* Don't use a template to initialize the i2c_adapter structure, it's
inefficient.
* Update a misleading comment on why we use i2c_transfer rather than
higher level i2c functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Satyam Sharma [Wed, 15 Aug 2007 14:35:38 +0000 (20:05 +0530)]
ieee1394: Fix kthread stopping in nodemgr_host_thread
The nodemgr host thread can exit on its own even when kthread_should_stop
is not true, on receiving a signal (might never happen in practice, as
it ignores signals). But considering kthread_stop() must not be mixed with
kthreads that can exit on their own, I think changing the code like this
is clearer. This change means the thread can cut its sleep short when
receive a signal but looking at the code around, that sounds okay (and
again, it might never actually recieve a signal in practice).
Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
7129 404 8 7541 1d75 drivers/ide/pci/sis5513.o.before
3916 404 1 4321 10e1 drivers/ide/pci/sis5513.o.after
Additionaly to being bloat the code contained two bugs:
- wrong cable bit was checked (0x0001 instead of 0x8000) on ATA_133 chipsets
- incorrect UDMA cycle time was reported on ATA_100a/ATA_133 chipsets
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
It has been obsoleted since 1 Nov 2004, is valid only when used together with
"ide=nodma" kernel parameter (which makes no sense) and only for aec62xx,
cmd64x, cs5220, generic, hpt366, sl82c105, tc86c001 and triflex host drivers.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This code doesn't use pci_assign_resource() and ide_get_or_set_dma_base() uses
pci_resource_start() to get DMA base address so it has no chance of working.
Moreover this belongs to PCI quirks (in case somebody would like to fix it).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-pmac: add PIO autotune fallback to ->ide_dma_check
Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets
->autotune this change shouldn't have any other effect than bringing ide-pmac
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-cris: add PIO autotune fallback to ->ide_dma_check
Since ide-cris allows separate PIO and DMA timings, and ide-cris always sets
->autotune this change shouldn't have any other effect than bringing ide-cris
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Mikael Starvik <starvik@axis.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sl82c105: add PIO autotune fallback to ->ide_dma_check
Since sl82c105 re-programs DMA/PIO timings for DMA enable/disable, and sets
->autotune this change shouldn't have any other effect than bringing sl82c105
driver in-line with other host drivers wrt ->ide_dma_check implementation.
cs5530/sc1200: add PIO autotune fallback to ->ide_dma_check
* Add PIO autotune fallback to ->ide_dma_check.
Since cs5530/sc1200 allow separate PIO and DMA timings, and cs5530/sc1200
always set ->autotune this change shouldn't have any other effect than
bringing these drivers in-line with other host drivers wrt ->ide_dma_check
implementations.
* Fix ->ide_dma_check to return "-1" if DMA cannot be set.
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
* Remove needless setting of drive->using_dma from auide_dma_check().
* Split off auide_mdma_filter() from auide_dma_check().
* Use ide_tune_dma() in auide_dma_check(), this fixes following issues:
- device's DMA capability bit not being checked
- device not being checked against generic DMA blacklist
- transfer mode not being set on device/host
* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode().
* ATI controllers allow separate PIO and DMA timings so remove programming
of PIO modes from atiixp_set_dma_mode(). Also remove no longer needed
atiixp_dma_2_pio() helper.
* SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA
mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable
support for SWDMA modes for now.
* Enable support for MWDMA0 mode.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always set ->autotune in init_hwif_sis5513(), this means practically
no change in behavior since PIO was always tuned in ->ide_dma_check
and >autotune was always set for ->dma_base == 0 case.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
MWDMA timings are taken from datasheets and they match ATA spec.
* Add generic helper function sis_program_timings() and use it in
->set_pio_mode and ->set_dma_mode methods (previously the driver
depended on BIOS to program the correct MWDMA timings).
* Remove redundant !chipset_family check from init_hwif_sis5513()
(init_chipset_sis5513() guarantees that we will never get here if
chipset_family cannot be determined).
* SWDMA seems to be unsupported by SiS chipsets (no info about SWDMA in
datasheets and for SWDMA0 mode timing requirements are impossible to
fulfill) so remove ->swdma_mask from init_hwif_sis5513() and handling
of SWDMA modes from sis_set_dma_mode().
* Enable DMA support for chipset_family == ATA_16.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tony Luck [Tue, 16 Oct 2007 20:17:22 +0000 (13:17 -0700)]
[IA64] Fix build for CONFIG_SMP=n
d5a7430ddcdb598261d70f7eb1bf450b5be52085 missed a spot where we
use cpu_sibling_map and cpu_core_map. These don't exist on a
uni-processor build. Wrap #ifdef CONFIG_SMP ... #endif around it.
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
Linus Torvalds [Tue, 16 Oct 2007 17:44:35 +0000 (10:44 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Increase cp0 compare clockevent min_delta_ns from 0x30 to 0x300.
[MIPS] Cache: Provide more information on cache policy on bootup.
[MIPS] Fix aliasing bug in copy_user_highpage, take 2.
[MIPS] VPE loader: convert from struct class_ device to struct device
[MIPS] MIPSsim: Fix booting from NFS root
[MIPS] Alchemy: Get rid of au1xxx_irq_map_t.
[MIPS] Alchemy: Get rid of au_ffz().
[MIPS] Alchemy: Get rid of au_ffs().
[MIPS] Alchemy: cleanup interrupt code.
[MIPS] Lasat: Fix build by conversion to irq_cpu.c.
[MIPS] Lasat: Add #ifndef ... #endif include warpper to lasatint.h.
[MIPS] IP22: Enable -Werror.
[MIPS] IP22: Fix warning.
[MIPS] IP22: Complain if requesting the front panel irq failed.
[MIPS] vmlinux.lds.S: Handle KPROBES_TEXT.
[MIPS] vmlinux.lds.S: Fix handling of .notes in final link.
[MIPS] vmlinux.lds.S: Remove duplicate comment.
[MIPS] MSP71XX: Add workarounds file.
[MIPS] IP32: Fix build by conversion to irq_cpu.c.
Ralf Baechle [Tue, 16 Oct 2007 10:35:11 +0000 (11:35 +0100)]
[MIPS] Increase cp0 compare clockevent min_delta_ns from 0x30 to 0x300.
Extremly low values are of dubious usefulness anyway but in this case
they actually were killing Qemu which simply wasn't able to complete
mips_next_event() within 0x30 100MHz cycles even on fast hosts.
Ralf Baechle [Mon, 15 Oct 2007 15:30:24 +0000 (16:30 +0100)]
[MIPS] Fix aliasing bug in copy_user_highpage, take 2.
Turns out b868868ae0f7272228c95cc760338ffe35bb739d wasn't quite right.
When called for a page that isn't marked dirty it would artificially
create an alias instead of doing the obvious thing and access the page
via KSEG0.
The same issue also exists in copy_to_user_page and copy_from_user_page
which was causing the machine to die under rare circumstances for example
when running ps if the BUG_ON() assertion added by the earlier fix was
getting triggered.
Thiemo Seufer [Sun, 14 Oct 2007 16:11:06 +0000 (17:11 +0100)]
[MIPS] MIPSsim: Fix booting from NFS root
MIPSsim probably doesn't have any sort of environment, but writing
a zero in it kills even the compiled in command line. This prevents
booting via NFS root.
Ralf Baechle [Sun, 14 Oct 2007 22:27:21 +0000 (23:27 +0100)]
[MIPS] IP22: Fix warning.
CC arch/mips/sgi-ip22/ip22-berr.o
arch/mips/sgi-ip22/ip22-berr.c: In function 'ip22_be_interrupt':
arch/mips/sgi-ip22/ip22-berr.c:100: warning: passing argument 2 of 'die_if_kernel' discards qualifiers from pointer target type
Ralf Baechle [Sun, 14 Oct 2007 22:04:27 +0000 (23:04 +0100)]
[MIPS] IP22: Complain if requesting the front panel irq failed.
This fixes the warning:
CC arch/mips/sgi-ip22/ip22-reset.o
arch/mips/sgi-ip22/ip22-reset.c: In function 'reboot_setup':
arch/mips/sgi-ip22/ip22-reset.c:239: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
projects / linux-2.6-omap-h63xx.git / log