David S. Miller [Thu, 29 Sep 2005 04:06:47 +0000 (21:06 -0700)]
[SPARC64]: Simplify user fault fixup handling.
Instead of doing byte-at-a-time user accesses to figure
out where the fault occurred, read the saved fault_address
from the current thread structure.
For the sake of defensive programming, if the fault_address
does not fall into the user buffer range, simply assume the
whole area faulted. This will cause the fixup for
copy_from_user() to clear the entire kernel side buffer.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Sep 2005 03:41:45 +0000 (20:41 -0700)]
[SPARC64]: Fix fault handling in unaligned trap handler.
We were not calling kernel_mna_trap_fault() correctly.
Instead of being fancy, just return 0 vs. -EFAULT from
the assembler stubs, and handle that return value as
appropriate.
Create an "__retl_efault" stub for assembler exception
table entries and use it where possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Sep 2005 05:50:06 +0000 (22:50 -0700)]
[SPARC64]: Add missing IDs for newer cpus.
Also, the us3_cpufreq driver can work on Ultra-IV and IV+.
They use the SAFARI bus register to control the clock divider
just like Ultra-III and III+ do.
Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] Make POSIX message queue sys_mq_open() honor umask
We ignored umask when creating new queues via mq_open (when creating
with open() on mqueue fs it is ok of course). According to the
specification this a bug. This trivial patch fixes this.
Signed-off-by: Krzysztof Benedyczak <golbi@mat.uni.torun.pl> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Chan [Tue, 27 Sep 2005 19:13:10 +0000 (12:13 -0700)]
[TG3]: misc. fixes
Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.
Add test for valid ethernet address in tg3_set_mac_addr().
Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 27 Sep 2005 19:12:42 +0000 (12:12 -0700)]
[TG3]: 5780 PHY fixes
Fix 5780 PHY related problems:
1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
register on 5705_PLUS chips or the chip will stop receiving after
a while. The MAC_RX_MODE reset is needed to prevent intermittently
losing the first receive packet on serdes chips.
2. Skip MAC loopback test on 5780 because of hardware errata. Normal
traffic including PHY loopback is not affected by the errata.
3. PHY loopback fails intermittently on 5708S and this is fixed by
putting the PHY in loopback mode first before programming the MAC
mode register. A MAC_RX_MODE reset is also added.
4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
nway_reset if 5780S is in parallel detect mode.
5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 27 Sep 2005 19:07:44 +0000 (12:07 -0700)]
[NEIGH]: Add debugging check when adding timers.
If we double-add a neighbour entry timer, which should be
impossible but has been reported, dump the current state of
the entry so that we can debug this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Mon, 26 Sep 2005 06:49:27 +0000 (07:49 +0100)]
[PATCH] missing dependency on arm O= builds
arm maketools needs include/asm-arm in place in the build tree.
On normal builds it's always there, of course, but on O= it's created
(by generic code) too late - when we get to asm-offset.h.
We used to get away with that by accident - creation of
include/asm-arm/arch symlink creates include/asm-arm and it happened
to go before maketools. However, we did not have such dependency,
so that luck didn't last - now maketools is picked first and we are screwed.
Both the symlink and maketools are prerequisites of the same
target (archprepare). This fix is obvious - make the latter explicitly
depend on the former and be done with that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Mon, 26 Sep 2005 04:49:44 +0000 (05:49 +0100)]
[PATCH] useless includes of linux/irq.h in arch/i386
Most of these guys are simply not needed (pulled by other stuff
via asm-i386/hardirq.h). One that is not entirely useless is hilarious -
arch/i386/oprofile/nmi_timer_int.c includes linux/irq.h... as a way to
get linux/errno.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David S. Miller [Mon, 26 Sep 2005 23:12:18 +0000 (16:12 -0700)]
[SPARC64]: Do not do TLB pre-filling any more.
In order to do it correctly on UltraSPARC-III+ and later we'd
need to add some complicated code to set the TAG access extension
register before loading the TLB.
Since this optimization gives questionable gains, it's best to
just remove it for now instead of adding the fix for Ultra-III+
Signed-off-by: David S. Miller <davem@davemloft.net>
Harald Welte [Mon, 26 Sep 2005 22:25:11 +0000 (15:25 -0700)]
[NETFILTER]: Fix invalid module autoloading by splitting iptable_nat
When you've enabled conntrack and NAT as a module (standard case in all
distributions), and you've also enabled the new conntrack netlink
interface, loading ip_conntrack_netlink.ko will auto-load iptable_nat.ko.
This causes a huge performance penalty, since for every packet you iterate
the nat code, even if you don't want it.
This patch splits iptable_nat.ko into the NAT core (ip_nat.ko) and the
iptables frontend (iptable_nat.ko). Threfore, ip_conntrack_netlink.ko will
only pull ip_nat.ko, but not the frontend. ip_nat.ko will "only" allocate
some resources, but not affect runtime performance.
This separation is also a nice step in anticipation of new packet filters
(nf-hipac, ipset, pkttables) being able to use the NAT core.
Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 26 Sep 2005 22:10:16 +0000 (15:10 -0700)]
[IPV6]: Fix [Bug 5306] Oops on IPv6 route lookup
> Steps to reproduce:
> 1. Boot Linux, do NOT setup any IPv6 routes
> 2. ip route get 2001::1 (or any unroutable address)
Well caught. We never set rt6i_idev on ip6_null_entry.
This patch should make the problem go away.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Williamson [Mon, 26 Sep 2005 21:28:02 +0000 (14:28 -0700)]
[NET]: Make sure ctl buffer is aligned properly in sys_sendmsg().
It's on the stack and declared as "unsigned char[]", but pointers
and similar can be in here thus we need to give it an explicit
alignment attribute.
Signed-off-by: Alex Williamson <alex.williamson@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Sanders [Mon, 26 Sep 2005 18:52:57 +0000 (19:52 +0100)]
[ARM] 2936/1: ixp4xx default config fixes
Patch from Vincent Sanders
A recent patch which made IXP4xx mach_desc's depend on config options
had the effect of not building the kernel for several machines it
possibly could be, this patch updates the default config to ensure all
possible machines are built for by default.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kars de Jong [Sun, 25 Sep 2005 12:39:46 +0000 (14:39 +0200)]
[PATCH] pcmcia: fix cross-platform issues with pcmcia module aliases
- Added a missing TO_NATIVE call to scripts/mod/file2alias.c:do_pcmcia_entry()
- Add an alignment attribute to struct pcmcia_device_no to solve an alignment
issue seen when cross-compiling on x86 for m68k.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Daniel Ritz [Tue, 20 Sep 2005 21:12:17 +0000 (14:12 -0700)]
[PATCH] yenta: add support for more TI bridges
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pci_set_power_state is not needed, as we call pci_enable_device() somewhere
else. Also, the resource we write to PCI_BASE_ADDRESS_0 needs to be converted
to bus-centric view first.
Daniel Ritz [Wed, 24 Aug 2005 15:03:23 +0000 (17:03 +0200)]
[PATCH] yenta: don't mess with bridge control register
In interrupt probing (both ISA and PCI) the bridge control register is used
to change interrupt routing to ISA or PCI by changing bit 7. But this bit
only controls the routing of card functional interrupts, not the CSC
interrupts which are used for interrupt probing.
A bad side effect of messing with this register in yenta_probe_irq() is
that it can lead to irq storms if a card is inserted and already powered by
the BIOS.
Usage in yenta_sock_init() and yenta_config_init() seem to be fishy as well.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Daniel Ritz [Mon, 22 Aug 2005 05:29:26 +0000 (22:29 -0700)]
[PATCH] yenta: auto-tune EnE bridges for CardBus cards
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Cc: Linus Torvalds <torvalds@osdl.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
NTFS: More $LogFile handling fixes: when chkdsk has been run, it can leave the
restart pages in the journal without multi sector transfer protection
fixups (i.e. the update sequence array is empty and in fact does not
exist).
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
David S. Miller [Mon, 26 Sep 2005 07:32:17 +0000 (00:32 -0700)]
[SPARC64]: Probe D/I/E-cache config and use.
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 25 Sep 2005 23:46:57 +0000 (16:46 -0700)]
[SPARC64]: Add CONFIG_DEBUG_PAGEALLOC support.
The trick is that we do the kernel linear mapping TLB miss starting
with an instruction sequence like this:
ba,pt %xcc, kvmap_load
xor %g2, %g4, %g5
succeeded by an instruction sequence which performs a full page table
walk starting at swapper_pg_dir.
We first take over the trap table from the firmware. Then, using this
constant PTE generation for the linear mapping area above, we build
the kernel page tables for the linear mapping.
After this is setup, we patch that branch above into a "nop", which
will cause TLB misses to fall through to the full page table walk.
With this, the page unmapping for CONFIG_DEBUG_PAGEALLOC is trivial.
Signed-off-by: David S. Miller <davem@davemloft.net>
[NET]: Protect neigh_stat_seq_fops by CONFIG_PROC_FS
From: Amos Waterland <apw@us.ibm.com>
If CONFIG_PROC_FS is not selected, the compiler emits this warning:
net/core/neighbour.c:64: warning: `neigh_stat_seq_fops' defined but not used
Which is correct, because neigh_stat_seq_fops is in fact only
initialized and used by code that is protected by CONFIG_PROC_FS. So
this patch fixes that up.
Signed-off-by: Amos Waterland <apw@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
We have to introduce a separate Kconfig menu entry for the NFQUEUE targets.
They cannot "just" depend on nfnetlink_queue, since nfnetlink_queue could
be linked into the kernel, whereas iptables can be a module.
Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This is one of those workarounds sucked over from sk98lin driver.
The skge driver needs to detect the Yukon-Lite A0 chip properly,
and turn of Rx FIFO Flush.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Current kernel has a couple of sneaky bugs in the ppc64 hugetlb code that
cause huge pages to be potentially left stale in the hash table and TLBs
(improperly invalidated), with all the nasty consequences that can have.
One is that we forgot to set the "secondary" bit in the hash PTEs when
hashing a huge page in the secondary bucket (fortunately very rare).
The other one is on non-LPAR machines (like Apple G5s), flush_hash_range()
which is used to flush a batch of PTEs simply did not work for huge pages.
Historically, our huge page code didn't batch, but this was changed without
fixing this routine. This patch fixes both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bhavesh P. Davda <bhavesh@avaya.com> noticed that SIGKILL wouldn't
properly kill a process under just the right cicumstances: a stopped
task that already had another signal queued would get the SIGKILL
queued onto the shared queue, and there it would remain until SIGCONT.
This simplifies the signal acceptance logic, and fixes the bug in the
process.
Ivan Kokshaysky [Fri, 23 Sep 2005 04:06:31 +0000 (21:06 -0700)]
[PATCH] pci: fixup parent subordinate busnr
I believe the change that broke things is introduction of
pci_fixup_parent_subordinate_busnr().
The patch here does two things:
- hunk #1 should fix the problems you've seen when you boot without
additional "pci" kernel options;
- hunk #2 supposedly fixes boot with "pci=assign-busses" option which
otherwise hangs Acer TM81xx machines as reported.
Please try this with and without "pci=assign-busses". If it boots,
I'd like to see 'lspci -vvx' for both cases.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NTFS: Change ntfs_cluster_free() to require a write locked runlist on entry
since we otherwise get into a lock reversal deadlock if a read locked
runlist is passed in. In the process also change it to take an ntfs
inode instead of a vfs inode as parameter.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Paul Gortmaker [Fri, 23 Sep 2005 09:18:45 +0000 (05:18 -0400)]
[PATCH] 8390 Tx fix for non i386 machines
While this is true, E8390_CMD is zero on i386, and thus there should be no
effect for these machines. Machines like Mac, Amiga etc. which use Alan's
clever register mapping may have a non-zero E8390_CMD and result in bogus
"transmitter busy" type messages from this bug.
Fix to allow SCTP_SHUTDOWN notifications to be received on 1-1 style
SCTP SOCK_STREAM sockets.
Add SCTP_SHUTDOWN notification to the receive queue before updating
the state of the association.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a number of bugs. It cannot be reasonably split up in
multiple fixes, since all bugs interact with each other and affect the same
function:
Bug #1:
The event cache code cannot be called while a lock is held. Therefore, the
call to ip_conntrack_event_cache() within ip_ct_refresh_acct() needs to be
moved outside of the locked section. This fixes a number of 2.6.14-rcX
oops and deadlock reports.
Bug #2:
We used to call ct_add_counters() for unconfirmed connections without
holding a lock. Since the add operations are not atomic, we could race
with another CPU.
Bug #3:
ip_ct_refresh_acct() lost REFRESH events in some cases where refresh
(and the corresponding event) are desired, but no accounting shall be
performed. Both, evenst and accounting implicitly depended on the skb
parameter bein non-null. We now re-introduce a non-accounting
"ip_ct_refresh()" variant to explicitly state the desired behaviour.
Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] Fix sparse endian warnings in pptp helper
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 23 Sep 2005 06:32:56 +0000 (23:32 -0700)]
[TCP]: Adjust Reno SACK estimate in tcp_fragment
Since the introduction of TSO pcount a year ago, it has been possible
for tcp_fragment() to cause packets_out to decrease. Prior to that,
tcp_retrans_try_collapse() was the only way for that to happen on the
retransmission path.
When this happens with Reno, it is possible for sasked_out to become
invalid because it is only an estimate and not tied to any particular
packet on the retransmission queue.
Therefore we need to adjust sacked_out as well as left_out in the Reno
case. The following patch does exactly that.
This bug is pretty difficult to trigger in practice though since you
need a SACKless peer with a retransmission that occurs just as the
cached MTU value expires.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
I've recently discovered the real functionality of device-mapper snapshots,
and since they are not well known, I've decided to write some docs for
them.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Wilson [Fri, 23 Sep 2005 04:44:28 +0000 (21:44 -0700)]
[PATCH] NFS: fix client oops when debugging is on
nfs_readpage_release() causes an oops while accessing a file with NFS
debugging turned on (echo 32767 > /proc/sys/sunrpc/nfs_debug) and a kernel
built with CONFIG_DEBUG_SLAB.
This patch moves the debugging statement above nfs_release_request() to
avoid accessing freed memory.
Signed-off-by: Nick Wilson <njw@osdl.org> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rob Landley [Fri, 23 Sep 2005 04:44:27 +0000 (21:44 -0700)]
[PATCH] Fix bd_claim() error code.
Problem: In some circumstances, bd_claim() is returning the wrong error
code.
If we try to swapon an unused block device that isn't swap formatted, we
get -EINVAL. But if that same block device is already mounted, we instead
get -EBUSY, even though it still isn't a valid swap device.
This issue came up on the busybox list trying to get the error message
from "swapon -a" right. If a swap device is already enabled, we get -EBUSY,
and we shouldn't report this as an error. But we can't distinguish the two
-EBUSY conditions, which are very different errors.
In the code, bd_claim() returns either 0 or -EBUSY, but in this case busy
means "somebody other than sys_swapon has already claimed this", and
_that_ means this block device can't be a valid swap device. So return
-EINVAL there.
Signed-off-by: Rob Landley <rob@landley.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: replace printk with "stack-friendly" printf - to report console failure
User get *a lot* confused when consoles don't work but we don't report
anything. And, as reported in the comment, using printk to report "your
console doesn't work" isn't likely to go that far.
Fix the problem on the base of this: stack consumption by host printf(). Use
kernel sprintf() and os_write_file, using a wild guess that one page will be
enough for the message, to preallocate the buffer with kmalloc().
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: use GFP_ATOMIC for allocations under spinlocks.
setup_initial_poll is only called with sigio_lock() held, so use appropriate
allocation.
Also, parse_chan() can also be called when holding a spinlock (see line_open()
-> parse_chan_pair()).
I have sporadic problems (spinlock taken twice, with spinlock debugging on UP)
which could be caused by a sequence like "take spinlock, alloc and go to
sleep, take again the spinlock in the other thread".
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6-omap-h63xx.git / log