Steve Wise [Wed, 25 Mar 2009 03:44:18 +0000 (20:44 -0700)]
RDMA/cxgb3: Enforce required firmware
The cxgb3 NIC driver can handle more firmware versions than iw_cxgb3,
and since commit 8207befa ("cxgb3: untie strict FW matching") cxgb3
will load with firmware versions that iw_cxgb3 can't handle. The FW
major number indicates a specific interface between the FW and
iw_cxgb3. Thus if the major number of the running firmware does not
match the required version compiled into iw_cxgb3, then iw_cxgb3 must
not register that device.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yevgeny Petrilin [Thu, 19 Mar 2009 02:49:54 +0000 (19:49 -0700)]
IB/mlx4: Unregister IB device prior to CLOSE PORT command
According to the ConnectX programmer's reference manual, all
operations should be stopped, all QPs should be torn down and all WQEs
flushed before the CLOSE_PORT command is invoked. In some cases
reversing the order of operations (as implemented now) could cause
a loss of completions.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yevgeny Petrilin [Thu, 19 Mar 2009 02:45:11 +0000 (19:45 -0700)]
mlx4_core: Add link type autosensing
When a port's link is down (except to driver restart) and the port is
configured for auto sensing, we try to sense port link type (Ethernet
or InfiniBand) in order to determine how to initialize the port. If
the port type needs to be changed, all mlx4 for the device interfaces
are unregistered and then registered again with the new port
types. Sensing is done with intervals of 3 seconds.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Faisal Latif [Fri, 6 Mar 2009 23:15:01 +0000 (15:15 -0800)]
RDMA/nes: Handle MPA Reject message properly
While doing testing, there are failures as MPA Reject call is not
handled. To handle MPA Reject call, following changes are done:
*Handle inbound/outbound MPA Reject response message.
When nes_reject() is called for pending MPA request reply,
send the MPA Reject message to its peer (active
side)cm_node. The peer cm_node (active side) will indicate
Reject message event for the pending Connect Request.
*Handle MPA Reject response message for loopback connections and listener.
When MPA Request is rejected, check if it is a loopback
connection and if it is then it will send Reject message event
to its peer loopback node. Also when destroying listener,
check if the cm_nodes for that listener are loopback or not.
*Add gracefull connection close with the MPA Reject response message.
Send gracefull close (FIN, FIN ACK..) to terminate the cm_nodes.
*Some code re-org while making the above changes.
Removed recv_list and recv_list_lock from the cm_node
structure as there can be only one receive close entry on the
timer. Also implemented handle_recv_entry() as receive close
entry is processed from both nes_rem_ref_cm_node() as well as
nes_cm_timer_tick().
Signed-off-by: Faisal Latif <faisal.latif@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don Wood [Fri, 6 Mar 2009 23:15:00 +0000 (15:15 -0800)]
RDMA/nes: Improve use of PBLs
Two level 256 byte PBLs was not implemented so the driver could report
out of memory when in fact there were PBLs still available.
This solution prefers to use 4KB PBLs over two level 256B PBLs until
the number of 4KB PBLs falls below a threshold. At this point the 4KB
PBL structure is converted to use 256B PBLs which prevents the driver
from running out of 4KB PBLs too quickly.
Signed-off-by: Don Wood <donald.e.wood@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Faisal Latif [Fri, 6 Mar 2009 23:12:11 +0000 (15:12 -0800)]
RDMA/nes: Remove LLTX
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver
and remove the NETIF_F_LLTX feature flag. This also fixes a warning
in some configs that comes from doing skb_linearize() call in the
hard_start_xmit method with IRQs disabled (if HIGHMEM is enabled,
skb_linearize() may end up enabling BHs, which is a no-no if hard IRQs
are disabled in that context). By getting rid of LLTX, we do not
disable IRQs when skb_linearize() is called.
Remove the sq_lock as it is not needed for non-LLTX. Fix ethtool not
to show the counter for sq_lock.
Reported-by: aluno3@poczta.onet.pl Signed-off-by: Faisal Latif <faisal.latif@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don Wood [Fri, 6 Mar 2009 23:12:11 +0000 (15:12 -0800)]
RDMA/nes: Inform hardware that asynchronous event has been handled
When asynchronous events are processed by software, it is necessary
to let the hardware know that software has handled the event. This
frees up the entry in the asynchronous event queue.
Signed-off-by: Don Wood <donald.e.wood@intel.com> Signed-off-by: Chien Tung <chien.tin.tung@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Chien Tung [Fri, 6 Mar 2009 23:12:11 +0000 (15:12 -0800)]
RDMA/nes: Fix tmp_addr compilation warning
In find_node(), tmp_addr causes an "unused variable" warning when
INFINIBAND_NES_DEBUG is not defined. It's only used in a nes_debug()
and the print does not make sense. So take out the whole thing.
Don Wood [Fri, 6 Mar 2009 23:12:09 +0000 (15:12 -0800)]
RDMA/nes: Account for freed PBL after HW operation
Fix occurrences where the software PBL counts were changed before the
hardware was updated. This bug allowed another thread to overallocate
the hardware resources.
Add proper PBL accounting in case nes_reg_mr() fails.
Signed-off-by: Don Wood <donald.e.wood@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Wed, 4 Mar 2009 23:22:39 +0000 (15:22 -0800)]
IB: Remove useless ibdev_is_alive() tests from sysfs code
Some attribute show functions test ibdev_is_alive() to make sure that
it's OK to access device state. However, the sysfs attributes will
not be registered until the device is fully initialized, and they'll
be unregistered before anything is torn down, so ibdev_is_alive()
doesn't do anything useful. Remove it.
If two events occur back-to-back (e.g., client-reregister and LID
change), both may pass the spinlock-protected code above before the
scheduled work updates the port->sm_ah handle. Then if the scheduled
work ends up running twice, the second operation will then find a
non-NULL port->sm_ah, and will simply overwrite it in update_sm_ah --
resulting in an AH leak.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Tue, 3 Mar 2009 22:22:17 +0000 (14:22 -0800)]
IB/mad: Fix ib_post_send_mad() returning 0 with no generate send comp
If ib_post_send_mad() returns 0, the API guarantees that there will be
a callback to send_buf->mad_agent->send_handler() so that the sender
can call ib_free_send_mad(). Otherwise, the ib_mad_send_buf will be
leaked and the mad_agent reference count will never go to zero and the
IB device module cannot be unloaded. The above can happen without
this patch if process_mad() returns (IB_MAD_RESULT_SUCCESS |
IB_MAD_RESULT_CONSUMED).
If process_mad() returns IB_MAD_RESULT_SUCCESS and there is no agent
registered to receive the mad being sent, handle_outgoing_dr_smp()
returns zero which causes a MAD packet which is at the end of the
directed route to be incorrectly sent on the wire but doesn't cause a
hang since the HCA generates a send completion.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Fri, 27 Feb 2009 22:44:32 +0000 (14:44 -0800)]
IB/mad: initialize mad_agent_priv before putting on lists
There is a potential race in ib_register_mad_agent() where the struct
ib_mad_agent_private is not fully initialized before it is added to
the list of agents per IB port. This means the ib_mad_agent_private
could be seen before the refcount, spin locks, and linked lists are
initialized. The fix is to initialize the structure earlier.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Fri, 27 Feb 2009 18:34:30 +0000 (10:34 -0800)]
IB/mad: Fix null pointer dereference in local_completions()
handle_outgoing_dr_smp() can queue a struct ib_mad_local_private
*local on the mad_agent_priv->local_work work queue with
local->mad_priv == NULL if device->process_mad() returns
IB_MAD_RESULT_SUCCESS | IB_MAD_RESULT_REPLY and
(!ib_response_mad(&mad_priv->mad.mad) ||
!mad_agent_priv->agent.recv_handler).
In this case, local_completions() will be called with local->mad_priv
== NULL. The code does check for this case and skips calling
recv_mad_agent->agent.recv_handler() but recv == 0 so
kmem_cache_free() is called with a NULL pointer.
Also, since recv isn't reinitialized each time through the loop, it
can cause a memory leak if recv should have been zero.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Ramachandra K [Fri, 27 Feb 2009 18:33:12 +0000 (10:33 -0800)]
IB/mad: Fix RMPP header RRespTime manipulation
Fix ib_set_rmpp_flags() to use the correct bit mask for RRespTime. In
the 8-bit field of the RMPP header, the first 5 bits are RRespTime and
next 3 bits are RMPPFlags. Hence to retain the first 5 bits, the mask
should be 0xF8 instead of 0xF1.
ack_recv()-->format_ack() calls ib_set_rmpp_flags() and due to the
incorrect ANDing with 0xF1, RRespTime got changed incorrectly and RMPP
Acks sent back always had a RRespTime of 0x1E (30) which caused the
other end to consider the time outs to be approximately 4297 seconds
(i.e. in the order of 4*2^30) instead of the usual ~4 seconds (order
of 4*2^20).
Signed-off-by: Ramachandra K <ramachandra.kuchimanchi@qlogic.com> Acked-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Or Gerlitz [Fri, 27 Feb 2009 18:30:46 +0000 (10:30 -0800)]
IB/iser: Remove hard setting of path MTU
Remove hard setting of the IB MTU used by iSER's RC queue-pair to 1K,
as this was done due to inter-op issues with an old iser target which
is not used any more.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Wed, 25 Feb 2009 21:27:46 +0000 (13:27 -0800)]
IB: Remove sysfs files before unregistering device
Move the ib_device_unregister_sysfs() call from ib_dealloc_device() to
ib_unregister_device(). The old code allows device unregister to
proceed even if some sysfs files are open, which leaves a window where
userspace can open a file before a device is removed but then end up
reading the file after the device is removed, which leads to various
kernel crashes either because the device data structure is freed or
because the low-level driver code is gone after module removal.
By not returning from ib_unregister_device() until after all sysfs
entries are removed, we make sure that data structures and/or module
code is not freed until after all sysfs access is done.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Mon, 23 Feb 2009 04:14:37 +0000 (20:14 -0800)]
IB/ipath: Really run work in ipath_release_user_pages_on_close()
ipath_release_user_pages_on_close() just allocated a structure to
schedule work with but just returned (leaking the structure) rather than
actually doing schedule_work(). Fix the logic to what was intended.
This was spotted by the Coverity checker (CID 2700).
Jack Morgenstein [Tue, 17 Feb 2009 22:51:47 +0000 (14:51 -0800)]
IPoIB: In unicast_arp_send(), only free newly-created paths
If path_rec_start() returns error, call path_free() only if the path
was newly-created. If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.
The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).
Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Moni Shua <monis@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Moni Shoua [Wed, 28 Jan 2009 23:15:56 +0000 (15:15 -0800)]
IB/mthca: Fix dispatch of IB_EVENT_LID_CHANGE event
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Moni Shoua [Wed, 28 Jan 2009 22:54:35 +0000 (14:54 -0800)]
IB/mlx4: Fix dispatch of IB_EVENT_LID_CHANGE event
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Harvey Harrison [Sun, 18 Jan 2009 01:11:57 +0000 (17:11 -0800)]
IB: Remove __constant_{endian} uses
The base versions handle constant folding just fine, use them
directly. The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.
This patch does not affect code generation at all.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Sat, 17 Jan 2009 22:28:53 +0000 (14:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Use consistent types for ehca_plpar_hcall9()
IB/ehca: Fix printk format warnings from u64 type change
IPoIB: Do not print error messages for multicast join retries
IB/mlx4: Fix memory ordering problem when posting LSO sends
mlx4_core: Fix min() warning
IPoIB: Fix deadlock between ipoib_open() and child interface create
IPoIB: Fix hang in napi_disable() if P_Key is never found
move wm8400-regulator's probe function to .devinit.text
A pointer to wm8400_regulator_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Stephen Rothwell [Fri, 16 Jan 2009 22:55:40 +0000 (14:55 -0800)]
IB/ehca: Use consistent types for ehca_plpar_hcall9()
ehca_plpar_hcall9() takes an unsigned long array, so make all callers
pass that in. This fixes warnings introduced by commit fe333321
("powerpc: Change u64/s64 to a long long integer type"), which changed
u64 from unsigned long to unsigned long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stephen Rothwell [Fri, 16 Jan 2009 22:55:28 +0000 (14:55 -0800)]
IB/ehca: Fix printk format warnings from u64 type change
Commit fe333321 ("powerpc: Change u64/s64 to a long long integer
type") changed u64 from unsigned long to unsigned long long, which
means that printk formats for printing u64 values should use "ll"
instead of "l" to avoid warnings. Fix all the places affected by this
in ehca.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yossi Etigin [Fri, 16 Jan 2009 21:42:59 +0000 (13:42 -0800)]
IPoIB: Do not print error messages for multicast join retries
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Fri, 16 Jan 2009 20:47:47 +0000 (12:47 -0800)]
IB/mlx4: Fix memory ordering problem when posting LSO sends
The current work request posting code writes the LSO segment before
writing any data segments. This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments. When the HCA processes this work request, a local
protection error may result.
Fix this by saving the LSO header size field off and writing it only
after all data segments are written. This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Fri, 16 Jan 2009 20:40:37 +0000 (12:40 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI PCI hotplug: harden against panic regression
ACPI: rename main.c to sleep.c
dell-laptop: move to drivers/platform/x86/ from drivers/misc/
eeepc-laptop: enable Bluetooth ACPI details
ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
kprobes: check CONFIG_FREEZER instead of CONFIG_PM
PM: Fix freezer compilation if PM_SLEEP is unset
thermal fixup for broken BIOS which has invalid trip points.
ACPI: EC: Don't trust ECDT tables from ASUS
ACPI: EC: Limit workaround for ASUS notebooks even more
ACPI: thinkpad-acpi: bump up version to 0.22
ACPI: thinkpad-acpi: handle HKEY event 6030
ACPI: thinkpad-acpi: clean-up fan subdriver quirk
ACPI: thinkpad-acpi: start the event hunt season
ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms
ACPI: thinkpad-acpi: clean up hotkey_notify()
ACPI: thinkpad-acpi: use killable instead of interruptible mutexes
ACPI: thinkpad-acpi: add UWB radio support
ACPI: thinkpad-acpi: preserve radio state across shutdown
ACPI: thinkpad-acpi: resume with radios disabled
...
James Bottomley [Thu, 15 Jan 2009 20:12:27 +0000 (15:12 -0500)]
ACPI PCI hotplug: harden against panic regression
ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136
Rather than reverting the entire commit that causes the crash: e8c331e963c58b83db24b7d0e39e8c07f687dbc6
"PCI hotplug: introduce functions for ACPI slot detection"
simply harden against it while the changes to
the hotplug code on this particularl machine are understood.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Len Brown <len.brown@intel.com>
Although rfkill support for the EEE bluetooth device has been added to
2.6.28-rc the appropriate ACPI accessor definitions were not added, so
the support was non functional. The patch below adds the get and set
accessors and has been verified to work on an EEE 901.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Acked-by: Matthew Garrett <mjg@redhat.com> Acked-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
David Brownell [Fri, 9 Jan 2009 20:17:08 +0000 (12:17 -0800)]
ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec;
that bit has nothing to do with status bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Fix this by making process.o compilation depend on CONFIG_FREEZER.
Reported-by: Cheng Renquan <crquan@gmail.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Fri, 16 Jan 2009 17:53:42 +0000 (12:53 -0500)]
thermal fixup for broken BIOS which has invalid trip points.
ACPI thermal driver only re-evaluate VALID trip points.
For the broken BIOS show in
http://bugzilla.kernel.org/show_bug.cgi?id=8544
the active[0] is set to invalid at boot time
and it will not be re-evaluated again.
We can still get a single warning message at boot time.
Dhananjay Phadke [Fri, 16 Jan 2009 19:03:25 +0000 (11:03 -0800)]
netxen: include ipv6.h (fixes build failure)
Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix ioctl arg size (userland incompatible change!)
Btrfs: Clear the device->running_pending flag before bailing on congestion
The structure used to send device in btrfs ioctl calls was not
properly aligned, and so 32 bit ioctls would not work properly on
64 bit kernels.
We could fix this with compat ioctls, but we're just one byte away
and it doesn't make sense at this stage to carry about the compat ioctls
forever at this stage in the project.
This patch brings the ioctl arg up to an evenly aligned 4k.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Fri, 16 Jan 2009 16:58:19 +0000 (11:58 -0500)]
Btrfs: Clear the device->running_pending flag before bailing on congestion
Btrfs maintains a queue of async bio submissions so the checksumming
threads don't have to wait on get_request_wait. In order to avoid
extra wakeups, this code has a running_pending flag that is used
to tell new submissions they don't need to wake the thread.
When the threads notice congestion on a single device, they
may decide to requeue the job and move on to other devices. This
makes sure the running_pending flag is cleared before the
job is requeued.
It should help avoid IO stalls by making sure the task is woken up
when new submissions come in.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Fri, 16 Jan 2009 16:41:09 +0000 (08:41 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
serial: Add 16850 uart type support to OF uart driver
hvc_console: Remove tty->low_latency
powerpc: Get the number of SLBs from "slb-size" property
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3
powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block
powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc
powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments
powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
powerpc/ps3: The lv1_ routines have u64 parameters
powerpc/ps3: Use dma_addr_t down through the stack
powerpc/ps3: set_dabr() takes an unsigned long
powerpc: Cleanup from l64 to ll64 change drivers/scsi
Linus Torvalds [Fri, 16 Jan 2009 16:40:57 +0000 (08:40 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl: Return non-zero on error in probe()
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
libata: New driver for OCTEON SOC Compact Flash interface (v7).
libata: Add another column to the ata_timing table.
sata_via: Add VT8261 support
pata_atiixp: update port enabledness test handling
[libata] get-identity ioctl: Fix use of invalid memory pointer
Linus Torvalds [Fri, 16 Jan 2009 16:14:51 +0000 (08:14 -0800)]
Revert "PCI PM: Register power state of devices during initialization"
This reverts commit 98e6e286d7b01deb7453b717aa38ebb69d6cefc0, as Yinghai
Lu reports that it breaks kexec with at least the e1000 and e1000e
drivers. The reason is that the shutdown sequence puts the hardware
into D3 sleep, and the commit causes us to claim that it then is in D0
(running) state just because we don't understand the PM capabilities.
Which then later makes "pci_set_power_state()" not do anything, and the
device never wakes up properly and just returns 0xff to everything.
Reported-by: Yinghai Lu <yinghai@kernel.org> Acked-by: From: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jesse Barnes <jesse.barnes@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 15 Jan 2009 00:48:42 +0000 (16:48 -0800)]
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Daney [Fri, 16 Jan 2009 01:45:32 +0000 (17:45 -0800)]
libata: New driver for OCTEON SOC Compact Flash interface (v7).
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Daney [Fri, 16 Jan 2009 01:45:31 +0000 (17:45 -0800)]
libata: Add another column to the ata_timing table.
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 16 Jan 2009 06:27:27 +0000 (15:27 +0900)]
pata_atiixp: update port enabledness test handling
Port enabledness test fits much better into init_one() instead of
pre_reset(). The reason why these tests are in pre_reset() is purely
historical at this point. Move it to init_one(). This will help
further changes.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jesse Barnes [Mon, 12 Jan 2009 20:05:32 +0000 (12:05 -0800)]
drm: initial KMS config fixes
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
For irq based hvc_console backends the tty->low_latency must be set to 0,
because the tty_flip_buffer_push() function must not be called from IRQ context
(see drivers/char/tty_buffer.c).
For polled backends, the low_latency setting causes the bug trace below, because
tty_flip_buffer_push() is called within an atomic context and subsequent calls
might sleep due to mutex_lock.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 14 Jan 2009 13:42:41 +0000 (13:42 +0000)]
powerpc: Get the number of SLBs from "slb-size" property
The PAPR says that the property for specifying the number of SLBs should
be called "slb-size". We currently only look for "ibm,slb-size" because
this is what firmware actually presents.
This patch makes us look for the "slb-size" property as well and in
preference to the "ibm,slb-size". This should future proof us if
firmware changes to match PAPR.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Wed, 14 Jan 2009 09:09:34 +0000 (09:09 +0000)]
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
The subpage_prot syscall fails on second and subsequent calls for a given
region, because is_hugepage_only_range() is mis-identifying the 4 kB
slices when the process has a 64 kB page size.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 2 of 'ps3_repository_read_mm_info' from incompatible pointer type
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 3 of 'ps3_repository_read_mm_info' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:00:29 +0000 (20:00 +0000)]
powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
This fixes these compiler warning:
arch/powerpc/platforms/ps3/interrupt.c:109: warning: passing argument 2 of 'clear_bit' from incompatible pointer type
arch/powerpc/platforms/ps3/interrupt.c:130: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 19:59:41 +0000 (19:59 +0000)]
powerpc/ps3: The lv1_ routines have u64 parameters
We just fix up the reference parameters as the others are dealt with by
arithmetic promotion rules and don't cause warnings.
This removes warnings like this:
arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type
Also, these:
drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 19:58:10 +0000 (19:58 +0000)]
powerpc/ps3: Use dma_addr_t down through the stack
Push the dma_addr_t type usage all the way down to where the actual
values are manipulated.
Now that u64 is "unsigned long long", this removes warnings like:
arch/powerpc/platforms/ps3/system-bus.c:532: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
arch/powerpc/platforms/ps3/system-bus.c:649: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Andrew Morton [Fri, 16 Jan 2009 04:43:56 +0000 (20:43 -0800)]
mlx4_core: Fix min() warning
Fix
drivers/net/mlx4/profile.c: In function `mlx4_make_profile':
drivers/net/mlx4/profile.c:110: warning: comparison of distinct pointer types lacks a cast
This happened because num_possible_cpus() was secretly changed by
commit ae7a47e7 ("cpumask: make cpumask.h eat its own dogfood.") from
returning "int" to (now) returning "unsigned int". I think that was a
good change, so we should just swallow the fallout.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Roland Dreier <rolandd@cisco.com> Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Cc: Jack Morgenstein <jackm@dev.mellanox.co.il> Cc: Vladimir Sokolovsky <vlad@mellanox.co.il> Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
projects / linux-2.6-omap-h63xx.git / log