For NX3031 mac addr should be read from firmware. mac addr in flash
is still valid, but can be overridden by firmware if running in
virtualization environment.
For old revisions, mac addr is retrieved directly from flash.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:16 +0000 (18:36 -0700)]
e1000e: remove unnecessary snippet missed in prior check_options update
The removal of this bit of code was missed in an earlier patch submittal.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:11 +0000 (18:36 -0700)]
e1000e: test for unusable MSI support
Some systems do not like 82571/2 use of 16-bit MSI messages and some
other systems claim to support MSI, but neither really works. Setup a
test MSI handler to detect whether or not MSI is working properly, and
if not, fallback to legacy INTx interrupts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:06 +0000 (18:36 -0700)]
e1000e: increase minimum frame size allowed
Setting an MTU value below 68 was disabling the network connection and
would not reconnect until the driver was reloaded. Prevent changing the
MTU to anything below 68.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:01 +0000 (18:36 -0700)]
e1000e: Increase Tx timeout factor for 10Mbps
Prevent Tx hangs from happening on 10Mb flood ping by increasing the
timeout factor.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:35:56 +0000 (18:35 -0700)]
e1000e: Use skb_copy_to_linear_data_offset introduced in 2.6.22
The e1000e driver was based on a version of e1000 prior to acme's
introduction of skb_copy_to_linear_data_offset, and was submitted
after acme went through and coverted all the drivers to use it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:35:51 +0000 (18:35 -0700)]
e1000e: Set InterruptThrottleRate to default when invalid value used
During module load, seting the InterruptThrottleRate parameter to an
invalid value would result in the itr/itr_setting pair being set to
unexpected values which would result in poor performance.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:35:44 +0000 (18:35 -0700)]
e1000e: Return 1 instead of a non-zero value for link up indication
A number of users have mentioned they have tools that rely on a link-up
indication having a return value of 1 rather than a non-zero value.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
tlan: Fix two regressions introduced by 64bit conversion.
Two regressions were introduced by the recent tlan: 64bit conversion
commit (93e16847c9db0093065c98063cfc639cdfccf19a). The first in
TLan_GetSKB caused a NULL pointer dereference. With the second causing
the link to fail to come up.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sky2: Fix suspend/hibernation/shutdown regression with WOL enabled (rev. 2)
On my test box with the Asus M3A32-MVP main board there is a
regression from 2.6.26 related to suspend, hibernation and
shutdown. Namely, if Wake-on-LAN is enabled with
'ethtool -s eth0 wol g', the box hangs solid during all of these
operations, while executing either sky2_suspend(), or
sky2_shutdown(). This patch fixes it for me.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The arm ixp4xx_eth driver doesn't compile in 2.6.27-rc1:
CC [M] drivers/net/arm/ixp4xx_eth.o
drivers/net/arm/ixp4xx_eth.c: In function 'eth_poll':
drivers/net/arm/ixp4xx_eth.c:554: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:554: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'eth_xmit':
drivers/net/arm/ixp4xx_eth.c:701: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:701: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'init_queues':
drivers/net/arm/ixp4xx_eth.c:886: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:886: error: too few arguments to function 'dma_mapping_error'
make[3]: *** [drivers/net/arm/ixp4xx_eth.o] Error 1
make[2]: *** [drivers/net/arm] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
dma_mapping_error() changed in 2.6.27-rc1 to also take a device parameter,
but nobody bothered updating ixp4xx_eth.c. Fixed by passing the appropriate
device value in the dma_mapping_error() calls.
Tested on an ixp425 box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Scott Wood [Tue, 12 Aug 2008 20:10:46 +0000 (15:10 -0500)]
gianfar: Call gfar_halt_nodisable() from gfar_halt().
gfar_halt() was factored out into halting and disabling by commit d87eb12785c14de1586e3bad86ca2c0991300339, as the suspend() method
only wants to do the former. However, the call to gfar_halt_nodisable()
from gfar_halt() apparently got lost during the patch respin process.
This adds it back.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Huang Weiyi [Mon, 11 Aug 2008 04:56:44 +0000 (12:56 +0800)]
[netdrvr] remove unnecessary #include
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/acenic.c
drivers/net/bnx2x_link.c
drivers/net/bnx2x_main.c
drivers/net/cpmac.c
drivers/net/gianfar_sysfs.c
drivers/net/ipg.h
drivers/net/ppp_mppe.c
drivers/net/pppol2tp.c
drivers/net/r6040.c
drivers/net/sh_eth.c
drivers/net/sky2.c
drivers/net/tehuti.h
drivers/net/typhoon.c
This patch removes the said #include <linux/version.h>.
Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Daniel Lezcano [Wed, 13 Aug 2008 23:15:57 +0000 (16:15 -0700)]
netns: Fix crash by making igmp per namespace
This patch makes the multicast socket to be per namespace.
When a network namespace is created, other than the init_net and a
multicast packet is received, the kernel goes to a hang or a kernel panic.
How to reproduce ?
* create a child network namespace
* create a pair virtual device veth
* ip link add type veth
* move one side to the pair network device to the child namespace
* ip link set netns <childpid> dev veth1
* ping -I veth0 224.0.0.1
The bug appears because the function ip_mc_init_dev does not initialize
the different multicast fields as it exits because it is not the init_net.
BUG: soft lockup - CPU#0 stuck for 61s! [avahi-daemon:2695]
Modules linked in:
irq event stamp: 50350
hardirqs last enabled at (50349): [<c03ee949>] _spin_unlock_irqrestore+0x34/0x39
hardirqs last disabled at (50350): [<c03ec639>] schedule+0x9f/0x5ff
softirqs last enabled at (45712): [<c0374d4b>] ip_setsockopt+0x8e7/0x909
softirqs last disabled at (45710): [<c03ee682>] _spin_lock_bh+0x8/0x27
Eilon Greenstein [Wed, 13 Aug 2008 22:58:49 +0000 (15:58 -0700)]
bnx2x: Minor code improvements
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:58:30 +0000 (15:58 -0700)]
bnx2x: Driver info
Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 13 Aug 2008 22:57:28 +0000 (15:57 -0700)]
bnx2x: 8073 PHY changes
8073 PHY changes
The initial support we had for this PHY needs some serious changing. The
major change is that this PHY should be initialized only when the first
function is loaded and not for each function. The official SPI-ROM of
this PHY was released and it requires some changes in the initialization
code as well
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:56:59 +0000 (15:56 -0700)]
bnx2x: Change GPIO for any port
Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 13 Aug 2008 22:56:17 +0000 (15:56 -0700)]
bnx2x: Pause settings
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 13 Aug 2008 22:55:28 +0000 (15:55 -0700)]
bnx2x: Link order with external PHY
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:53:12 +0000 (15:53 -0700)]
bnx2x: Wrong structure size
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:52:28 +0000 (15:52 -0700)]
bnx2x: Clearing MAC addresses filters
Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:52:08 +0000 (15:52 -0700)]
bnx2x: Delay in while loops
Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:51:48 +0000 (15:51 -0700)]
bnx2x: PBA Table Page Alignment Workaround
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:51:28 +0000 (15:51 -0700)]
bnx2x: Self-test false positive
Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
loop (not causing a failure - just ugly)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:51:07 +0000 (15:51 -0700)]
bnx2x: Memory allocation
Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
not support it. Fixed to allocate according to the chip type to save
memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:50:23 +0000 (15:50 -0700)]
bnx2x: HW lock mechanism
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:49:35 +0000 (15:49 -0700)]
bnx2x: FW Internal Memory structure
FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:49:05 +0000 (15:49 -0700)]
bnx2x: Statistics
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:47:33 +0000 (15:47 -0700)]
bnx2x: FW (bootcode) interface fixes
FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 13 Aug 2008 22:18:38 +0000 (15:18 -0700)]
pkt_sched: Fix queue quiescence testing in dev_deactivate().
Based upon discussions with Jarek P. and Herbert Xu.
First, we're testing the wrong qdisc. We just reset the device
queue qdiscs to &noop_qdisc and checking it's state is completely
pointless here.
We want to wait until the previous qdisc that was sitting at
the ->qdisc pointer is not busy any more. And that would be
->qdisc_sleeping.
Because of how we propagate the samples qdisc pointer down into
qdisc_run and friends via per-cpu ->output_queue and netif_schedule,
we have to wait also for the __QDISC_STATE_SCHED bit to clear as
well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Wed, 13 Aug 2008 22:16:43 +0000 (15:16 -0700)]
pkt_sched: Fix oops in htb_delete.
Recent changes introduced a bug in htb_delete(): cl->parent->children
counter update misses checking cl->parent for NULL, which is used for
root classes, so deleting them causes an oops.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Gallatin [Wed, 13 Aug 2008 22:16:00 +0000 (15:16 -0700)]
pktgen: prevent pktgen from using bad tx queue
With the new multi-queue transmit code, it is possible to accidentally
make pktgen pick a non-existing tx queue simply by using a stale
script to drive pktgen. Access to this non-existing tx queue will
then trigger a bad memory access and kill the machine.
For example, setting "queue_map_max 2" will cause my machine to die
when accessing a garbage spinlock in the non-existing tx queue:
BUG: spinlock bad magic on CPU#0, kpktgend_0/564
lock: ffff88001ddf6718, .magic: ffffffff, .owner: /-1, .owner_cpu: 0
Pid: 564, comm: kpktgend_0 Not tainted 2.6.27-rc3 #35
dccp: change L/R must have at least one byte in the dccpsf_val field
Thanks to Eugene Teo for reporting this problem.
Signed-off-by: Eugene Teo <eugenete@kernel.sg> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Wed, 13 Aug 2008 09:41:22 +0000 (02:41 -0700)]
net-sched: Fix actions flushing
Flushing of actions has been broken since we changed
the semantics of netlink parsed tb[X] to mean X is an attribute type.
This makes the flushing work.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Julien Brunel [Wed, 13 Aug 2008 09:40:48 +0000 (02:40 -0700)]
net/rxrpc: Use an IS_ERR test rather than a NULL test
In case of error, the function rxrpc_get_transport returns an ERR
pointer, but never returns a NULL pointer. So after a call to this
function, a NULL test should be replaced by an IS_ERR test.
A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x = rxrpc_get_transport(...)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
)
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 13 Aug 2008 09:13:34 +0000 (02:13 -0700)]
pkt_sched: Add queue stopped test back to qdisc_run().
Based upon a bug report by Andrew Gallatin on netdev
with subject "CPU utilization increased in 2.6.27rc"
In commit 37437bb2e1ae8af470dfcd5b4ff454110894ccaf
("pkt_sched: Schedule qdiscs instead of netdev_queue.")
the test of the queue being stopped was erroneously
removed from qdisc_run().
When the TX queue of the device fills up, this omission
causes lots of extraneous useless work to be queued up
to softirq context, where we'll just return immediately
because the device is still stuffed up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Mon, 11 Aug 2008 07:19:14 +0000 (17:19 +1000)]
ipvs: Explictly clear ip_vs_stats members
In order to align the coding styles of ip_vs_zero_stats() and
its child-function ip_vs_zero_estimator(), clear ip_vs_stats
members explicitlty rather than doing a limited memset().
This was chosen over modifying ip_vs_zero_estimator() to use
memset() as it is more robust against changes in members
in the relevant structures. memset() would be prefered if
all members of the structure were to be cleared.
Cc: Sven Wegener <sven.wegener@stealer.net> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Sven Wegener [Sun, 10 Aug 2008 18:24:41 +0000 (18:24 +0000)]
ipvs: Embed estimator object into stats object
There's no reason for dynamically allocating an estimator object for every
stats object. Directly embed an estimator object into every stats object and
switch to using the kernel-provided list implementation. This makes the code
much simpler and faster, as we do not need to traverse the list of all
estimators to find the one belonging to a stats object. There's no need to use
an rwlock, as we only have one reader. Also reorder the members of the
estimator structure slightly to avoid padding overhead. This can't be done
with the stats object as the members are currently copied to our user space
object via memcpy() and changing it would break ABI.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au>
Sven Wegener [Sun, 10 Aug 2008 18:24:35 +0000 (18:24 +0000)]
ipvs: Annotate init functions with __init
Being able to discard these functions saves a couple of bytes at runtime. The
cleanup functions can't be annotated with __exit as they are also called from
init functions.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au>
Sven Wegener [Sun, 10 Aug 2008 09:17:59 +0000 (09:17 +0000)]
ipvs: Fix possible deadlock in estimator code
There is a slight chance for a deadlock in the estimator code. We can't call
del_timer_sync() while holding our lock, as the timer might be active and
spinning for the lock on another cpu. Work around this issue by using
try_to_del_timer_sync() and releasing the lock. We could actually delete the
timer outside of our lock, as the add and kill functions are only every called
from userspace via [gs]etsockopt() and are serialized by a mutex, but better
make this explicit.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Cc: stable <stable@kernel.org> Acked-by: Simon Horman <horms@verge.net.au>
Sven Wegener [Sun, 10 Aug 2008 09:14:05 +0000 (09:14 +0000)]
ipvs: Fix possible deadlock in sync code
Commit 998e7a76804b7a273a0460c2cdd5a51fa9856717 ("ipvs: Use kthread_run()
instead of doing a double-fork via kernel_thread()") introduced a possible
deadlock in the sync code. We need to use the _bh versions for the lock, as the
lock is also accessed from a bottom half.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au>
Herbert Xu [Sat, 9 Aug 2008 07:35:05 +0000 (00:35 -0700)]
udp: Drop socket lock for encapsulated packets
The socket lock is there to protect the normal UDP receive path.
Encapsulation UDP sockets don't need that protection. In fact
the locking is deadly for them as they may contain another UDP
packet within, possibly with the same addresses.
Also the nested bit was copied from TCP. TCP needs it because
of accept(2) spawning sockets. This simply doesn't apply to UDP
so I've removed it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Thu, 7 Aug 2008 20:26:54 +0000 (22:26 +0200)]
[Bluetooth] Add parameters to control BNEP header compression
The Bluetooth qualification for PAN demands testing with BNEP header
compression disabled. This is actually pretty stupid and the Linux
implementation outsmarts the test system since it compresses whenever
possible. So to pass qualification two need parameters have been added
to control the compression of source and destination headers.
Sujith [Thu, 7 Aug 2008 05:23:10 +0000 (10:53 +0530)]
ath9k: Remove redundant data structure ath9k_txq_info
Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Tue, 5 Aug 2008 19:06:51 +0000 (22:06 +0300)]
ath9k: work around gcc ICEs
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
list.h: Add list_splice_tail() and list_splice_tail_init()
If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 6 Aug 2008 14:18:31 +0000 (16:18 +0200)]
rt2x00: Block all unsupported modes
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a mesh node will not forward a multicast frame if it is not subscribed
to the specific multicast address. This patch addresses the issue and fixes mesh
multicast forwarding.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6-omap-h63xx.git / log