Tejun Heo [Fri, 2 Feb 2007 05:51:09 +0000 (14:51 +0900)]
ahci/pata_jmicron: fix JMicron quirk
For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set. This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.
The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits. If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.
This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
avr32@atmel.com is a technical support address and is not really
appropriate for sending patches. Lots of annoying automatics getting
in the way.
I'm still the maintainer of all the entries touched by this patch, so
nothing changes with regard to the "Supported" status of the AVR32
architecture or the macb driver.
Randy Dunlap [Thu, 1 Feb 2007 07:48:17 +0000 (23:48 -0800)]
[PATCH] sysrq: showBlockedTasks is sysrq-W
Change SysRq showBlockedTasks from sysrq-X to sysrq-W and show that in the
Help message.
It was previously done via X, but X is already used for Xmon on ppc & powerpc
platforms and this collision needs to be avoided.
All callers of register_sysrq_key() are now marked in the sysrq op/key table.
I didn't mark 'h' as Help because Help is just printed for any unknown key,
such as '?'.
Added some omitted sysrq key entries in the sysrq.txt file.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avi Kivity [Thu, 1 Feb 2007 07:48:13 +0000 (23:48 -0800)]
[PATCH] KVM: fix lockup on 32-bit intel hosts with nx disabled in the bios
Intel hosts, without long mode, and with nx support disabled in the bios
have an efer that is readable but not writable. This causes a lockup on
switch to guest mode (even though it should exit with reason 34 according
to the documentation).
Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 1 Feb 2007 07:48:13 +0000 (23:48 -0800)]
[PATCH] pci: remove warning messages
Remove these recently-added warnings. They don't tell us anythng very
interesting and Kumar says "On an embedded PPC reference system I see this
message 6 times when I've got no cards in the PCI slots."
Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare [Thu, 1 Feb 2007 07:48:12 +0000 (23:48 -0800)]
[PATCH] via quirk update
Add special handling for the VT82C686.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Thu, 1 Feb 2007 13:52:33 +0000 (13:52 +0000)]
[PATCH] sanitize sections for sparc32 smp
a) sun4d_boot_one_cpu() should be __cpuinit (called only from
__cpuinit __cpu_up(), for one thing, leads to calls of __cpuinit
functions for another).
b) got externs in arch/sparc/kernel/smp.c to match reality.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Thu, 1 Feb 2007 13:52:23 +0000 (13:52 +0000)]
[PATCH] __crc_... is intended to be absolute
i386 boot/compressed/relocs checks for absolute symbols and warns about
unexpected ones. If you build with modversions, you get ~2500 warnings
about __crc_<symbol>. These suckers are really absolute symbols - we
do _not_ want to modify them on relocation.
They are generated by genksyms - EXPORT_... generates a weak alias, then
genksyms produces an ld script with __crc_<symbol> = <checksum> and it's
fed to ld to produce the final object file. Their only use is to match
kernel and module at modprobe time; they _must_ be absolute.
boot/compressed/relocs has a whitelist of known absolute symbols, but
it doesn't know about __crc_... stuff. As the result, we get shitloads
of false positives on any ld(1) version.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Thu, 1 Feb 2007 13:08:45 +0000 (13:08 +0000)]
[PATCH] fix frv headers_check
a) registers.h is really needed there
b) include of asm-generic/termios should be under __KERNEL__
c) includes of asm-generic/{memory_model,page} should be under
__KERNEL (nothing in there that would work in userland)
d) a lot of stuff in ptrace.h should be under __KERNEL__.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: xt_hashlimit: fix ip6tables dependency
[SCTP]: Force update of the rto when processing HB-ACK
[IPV6]: fix BUG of ndisc_send_redirect()
[IPV6]: Fix up some CONFIG typos
[NETFILTER]: SIP conntrack: fix out of bounds memory access
[NETFILTER]: SIP conntrack: fix skipping over user info in SIP headers
[NETFILTER]: xt_connbytes: fix division by zero
[MAINTAINERS]: netfilter@ is subscribers-only
IP6_NF_IPTABLES=m, CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=y results in a
linker error since ipv6_find_hdr is defined in ip6_tables.c. Fix similar
to Adrian Bunk's H.323 conntrack patch: selecting ip6_tables to be build
as module requires hashlimit to be built as module as well.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 31 Jan 2007 01:02:08 +0000 (17:02 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: fix pb_fnmode and move it to generic HID
HID: fix hid-input mapping for Firefly Mini Remote Control
USB HID: fix hid_blacklist clash for 0x08ca/0x0010
HID: fix memleaking of collection
David Barksdale [Tue, 30 Jan 2007 22:36:25 +0000 (14:36 -0800)]
[PATCH] IPMI: fix timeout list handling
Fix a dangling pointer bug in ipmi_timeout_handler. A list of timedout
messages is not re-initialized before reuse, causing the head of the list
to point to freed memory.
Signed-off-by: David Barksdale <amatus@ocgnet.org> Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Dike [Tue, 30 Jan 2007 22:36:17 +0000 (14:36 -0800)]
[PATCH] uml: fix signal frame alignment
Use the same signal frame alignment calculations as the underlying
architecture. x86_64 appeared to do this, but the "- 8" was really
subtracting 8 * sizeof(struct rt_sigframe) rather than 8 bytes.
UML/i386 might have been OK, but I changed the calculation to match
i386 just to be sure.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: <stable@kernel.org> Cc: Adrian Bunk <bunk@stusta.de> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Antoine Martin <antoine@nagafix.co.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My understanding is that pci_find_present() doesn't work yet at the time
the quirks are run. So I used a two-step quirk as is done for some other
quirks already. First we detect the VIA south bridges and set the right
low and high device limits, then we are ready to actually run the quirks on
the affected devices.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masami Hiramatsu [Tue, 30 Jan 2007 22:36:06 +0000 (14:36 -0800)]
[PATCH] kprobes: replace magic numbers with enum
Replace the magic numbers with an enum, and gets rid of a warning on the
specific architectures (ex. powerpc) on which the compiler considers
'char' as 'unsigned char'.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Tue, 30 Jan 2007 22:36:01 +0000 (14:36 -0800)]
[PATCH] Remove warning: VFS is out of sync with lock manager
But keep it as a dprintk
The message can be generated in a quite normal situation:
If a 'lock' request is interrupted, then the lock client needs to
record that the server has the lock, incase it does.
When we come the unlock, the server might say it doesn't, even
though we think it does (or might) and this generates the message.
Signed-off-by: Neil Brown <neilb@suse.de> Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Tue, 30 Jan 2007 22:35:55 +0000 (14:35 -0800)]
[PATCH] translate dashes in filenames for headers install
The current filename->define translation does not scrub dashes so when
creating stub defines for like asm-x86_64/ptrace-abi.h, we get: #define
__ASM_STUB_PTRACE-ABI_H
gcc just hates that sort of thing :)
trivial attached patch adds - to the tr list to scrub it to _
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Litke [Tue, 30 Jan 2007 22:35:39 +0000 (14:35 -0800)]
[PATCH] Don't allow the stack to grow into hugetlb reserved regions
When expanding the stack, we don't currently check if the VMA will cross
into an area of the address space that is reserved for hugetlb pages.
Subsequent faults on the expanded portion of such a VMA will confuse the
low-level MMU code, resulting in an OOPS. Check for this.
Signed-off-by: Adam Litke <agl@us.ibm.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlad Yasevich [Tue, 30 Jan 2007 22:36:14 +0000 (14:36 -0800)]
[SCTP]: Force update of the rto when processing HB-ACK
When processing a HEARTBEAT-ACK it's possible that the transport rto
timers will not be updated because a prior T3-RTX processing would
have cleared the rto_pending flag on the transport. However, if
we received a valid HEARTBEAT-ACK, we want to force update the
rto variables, so re-set the rto_pending flag before calling
sctp_transport_update_rto().
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Yewang [Tue, 30 Jan 2007 22:33:20 +0000 (14:33 -0800)]
[IPV6]: fix BUG of ndisc_send_redirect()
When I tested IPv6 redirect function about kernel 2.6.19.1, and found
that the kernel can send redirect packets whose target address is global
address, and the target is not the actual endpoint of communication.
But the criteria conform to RFC2461, the target address defines as
following:
Target Address An IP address that is a better first hop to use for
he ICMP Destination Address. When the target is
the actual endpoint of communication, i.e., the
destination is a neighbor, the Target Address field
MUST contain the same value as the ICMP Destination
Address field. Otherwise the target is a better
first-hop router and the Target Address MUST be the
router's link-local address so that hosts can
uniquely identify routers.
According to this definition, when a router redirect to a host, the
target address either the better first-hop router's link-local address
or the same as the ICMP destination address field. But the function of
ndisc_send_redirect() in net/ipv6/ndisc.c, does not check the target
address correctly.
There is another definition about receive Redirect message in RFC2461:
8.1. Validation of Redirect Messages
A host MUST silently discard any received Redirect message that does
not satisfy all of the following validity checks:
......
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
......
And the receive redirect function of ndisc_redirect_rcv() implemented
this definition, checks the target address correctly.
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not link-local.\n");
return;
}
So, I think the send redirect function must check the target address
also.
Signed-off-by: Li Yewang <lyw@nanjing-fnst.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Lars Immisch [Tue, 30 Jan 2007 22:24:57 +0000 (14:24 -0800)]
[NETFILTER]: SIP conntrack: fix skipping over user info in SIP headers
When trying to skip over the username in the Contact header, stop at the
end of the line if no @ is found to avoid mangling following headers.
We don't need to worry about continuation lines because we search inside
a SIP URI.
Fixes Netfilter Bugzilla #532.
Signed-off-by: Lars Immisch <lars@ibp.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 30 Jan 2007 22:24:29 +0000 (14:24 -0800)]
[NETFILTER]: xt_connbytes: fix division by zero
When the packet counter of a connection is zero a division by zero
occurs in div64_64(). Fix that by using zero as average value, which
is correct as long as the packet counter didn't overflow, at which
point we have lost anyway.
Additionally we're probably going to go back to 64 bit counters
in 2.6.21.
Based on patch from Jonas Berlin <xkr47@outerspace.dyndns.org>,
with suggestions from KOVACS Krisztian <hidden@balabit.hu>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
It's wrong. We had a lengthy analysis of this piece of code
several months ago, and it is correct.
Consider, if we run the loop and we get an error
the following happens:
1) attempt of ifb_init_one(i) fails, therefore we should
not try to "ifb_free_one()" on "i" since it failed
2) the loop iteration first increments "i", then it
check for error
Therefore we must decrement "i" twice before the first
free during the cleanup. One to "undo" the for() loop
increment, and one to "skip" the ifb_init_one() case which
failed."
Reported-by: David Miller <davem@davemloft.net> Acked-by: Jeff Garzik <jgarzik@pobox.com> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serge E. Hallyn [Tue, 30 Jan 2007 21:28:23 +0000 (15:28 -0600)]
[PATCH] namespaces: fix task exit disaster
This is based on a patch by Eric W. Biederman, who pointed out that pid
namespaces are still fake, and we only have one ever active.
So for the time being, we can modify any code which could access
tsk->nsproxy->pid_ns during task exit to just use &init_pid_ns instead,
and move the exit_task_namespaces call in do_exit() back above
exit_notify(), so that an exiting nfs server has a valid tsk->sighand to
work with.
Long term, pulling pid_ns out of nsproxy might be the cleanest solution.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
[ Eric's patch fixed to take care of free_pid() too ]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 30 Jan 2007 21:35:18 +0000 (13:35 -0800)]
Revert "[PATCH] namespaces: fix exit race by splitting exit"
This reverts commit 7a238fcba0629b6f2edbcd37458bae56fcf36be5 in
preparation for a better and simpler fix proposed by Eric Biederman
(and fixed up by Serge Hallyn)
Acked-by: Serge E. Hallyn <serue@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 30 Jan 2007 16:46:17 +0000 (08:46 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: fix translation for START STOP UNIT
libata-scsi: ata_task_ioctl should return ATA registers from sense data
pata_platform: set_mode fix
ata_if_xfermask() word 51 fix
pata_sil680: PIO1 taskfile transfers overclocking fix (repost)
libata: fix ata_eh_suspend() return value
ahci: port_no should be used when clearing IRQ in ahci_thaw()
Fix trivial conflict in drivers/ata/pata_platform.c manually
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Add new IDs to VIA AGP.
[AGPGART] Remove pointless assignment.
[AGPGART] Remove pointless typedef in ati-agp
[AGPGART] Prevent (unlikely) memory leak in amd_create_gatt_pages()
[AGPGART] intel_agp: restore graphics device's pci space early in resume
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
via82cxxx/pata_via: correct PCI_DEVICE_ID_VIA_SATA_EIDE ID and add support for CX700 and 8237S
ide: unregister idepnp driver on unload
ide: add missing __init tags to IDE PCI host drivers
ia64: add pci_get_legacy_ide_irq()
ide/generic: Jmicron has its own drivers now
atiixp.c: add cable detection support for ATI IDE
atiixp.c: sb600 ide only has one channel
atiixp.c: remove unused code
jmicron: fix warning
ide: update MAINTAINERS entry
Al Viro [Tue, 30 Jan 2007 13:23:40 +0000 (13:23 +0000)]
[PATCH] fix indentation-related breakage in Kconfig.i386
Kconfig recognizes the end of help text by receding indentation depth.
Recent patch had broken HOST_VMSPLIT_... choice in arch/um/Kconfig.i386 -
all alternatives are interpreted as part of help text now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
What DMA for 16bit pcmcia card, anyway? We never do request_dma()
there and ->dma_channel never changes since initialization to -1.
IOW, that call is dead code.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 30 Jan 2007 16:35:12 +0000 (08:35 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix typo of "CONFIG_MT_SMP".
[MIPS] Ocelot G: Fix a few misspellings of CONFIG_GALILEO_GT64240_ETH
[PATCH] Malta: Fix build if CONFIG_MTD is diabled.
Hugh Dickins [Mon, 29 Jan 2007 21:24:08 +0000 (21:24 +0000)]
[PATCH] mm: mremap correct rmap accounting
Nick Piggin points out that page accounting on MIPS multiple ZERO_PAGEs
is not maintained by its move_pte, and could lead to freeing a ZERO_PAGE.
Instead of complicating that move_pte, just forget the minor optimization
when mremapping, and change the one thing which needed it for correctness
- filemap_xip use ZERO_PAGE(0) throughout instead of according to address.
[ "There is no block device driver one could use for XIP on mips
platforms" - Carsten Otte ]
[PATCH] i386: In assign_irq_vector look at all vectors before giving up
When the world was a simple and static place setting up irqs was easy.
It sufficed to allocate a linux irq number and a find a free cpu
vector we could receive that linux irq on. In those days it was
a safe assumption that any allocated vector was actually in use
so after one global pass through all of the vectors we would have
none left.
These days things are much more dynamic with interrupt controllers
(in the form of MSI or MSI-X) appearing on plug in cards and linux
irqs appearing and disappearing. As these irqs come and go vectors
are allocated and freed, invalidating the ancient assumption that all
allocated vectors stayed in use forever.
So this patch modifies the vector allocator to walk through every
possible vector before giving up, and to check to see if a vector
is in use before assigning it. With these changes we stop leaking
freed vectors and it becomes possible to allocate and free irq vectors
all day long.
This changed was modeled after the vector allocator on x86_64 where
this limitation has already been removed. In essence we don't update
the static variables that hold the position of the last vector we
allocated until have successfully allocated another vector. This
allows us to detect if we have completed one complete scan through
all of the possible vectors.
Acked-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 30 Jan 2007 16:29:05 +0000 (08:29 -0800)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4117/1: S3C2412: Fix writel() usage in selection code
[ARM] 4111/1: Allow VFP to work with thread migration on SMP
[ARM] 4112/1: Only ioremap to supersections if DOMAIN_IO is zero
[ARM] 4106/1: S3C2410: typo fixes in register definitions
[ARM] 4102/1: Allow for PHYS_OFFSET on any valid 2MiB address
[ARM] Fix AMBA serial drivers for non-first serial ports
[ARM] 4100/1: iop3xx: fix cpu mask for iop333
[ARM] Update mach-types
[ARM] Fix show_mem() for discontigmem
[ARM] 4096/1: S3C24XX: change return code form s3c2410_gpio_getcfg()
[ARM] 4095/1: S3C24XX: Fix GPIO set for Bank A
[ARM] 4092/1: i.MX/MX1 CPU Frequency scaling latency definition
[ARM] 4089/1: AT91: GPIO wake IRQ cleanup
[ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resume
[ARM] 4087/1: AT91: CPU reset for SAM9x processors
[ARM] 4086/1: AT91: Whitespace cleanup
[ARM] 4085/1: AT91: Header fixes.
[ARM] 4084/1: Remove CONFIG_DEBUG_WAITQ
[PATCH] `make help' in build tree doesn't show headers_* targets
`make help' in the build tree doesn't show the help texts about the
`headers_install' and `headers_check' targets because it looks for
include/asm-$(ARCH)/Kbuild in the wrong place.
Add the missing `$(srctree)' prefixes to fix this.
Also move the printing of the default install path for the headers inside the
`if/fi', where it belongs.
During ufs_trunc_direct which is subroutine of ufs::truncate, we try the first
of all free parts of block and then whole blocks. But we calculate size of
block's part to free in the wrong way.
This may cause bad update of used blocks and fragments statistic, and you can
got report that you have free 32T on 1Gb partition.
These series of patches result of UFS1 write support stress testing, like
running fsx-linux, untar and build linux kernel etc
We pass from ufs::get_block_t to levels below: pointer to the current page, to
make possible things like reallocation of blocks on the fly, and we also uses
this pointer for indication, what actually we allocate data block or meta data
block, but currently we make decision about what we allocate on the wrong
level, this may and cause oops if we allocate blocks in some special order.
Miklos Szeredi [Mon, 29 Jan 2007 21:19:54 +0000 (13:19 -0800)]
[PATCH] fuse: fix bug in control filesystem mount
The BUG in fuse_ctl_add_dentry() could be triggered if the control
filesystem was unmounted and mounted again while one or more fuse
filesystems were present.
The fix is to reset the dentry counter in fuse_ctl_kill_sb().
Andrew Morton [Mon, 29 Jan 2007 21:19:50 +0000 (13:19 -0800)]
[PATCH] m68k: uaccess.h needs sched.h
In file included from include/linux/crypto.h:26,
from crypto/cipher.c:17:
include/linux/uaccess.h: In function 'pagefault_disable':
include/linux/uaccess.h:18: error: dereferencing pointer to incomplete type
include/linux/uaccess.h: In function 'pagefault_enable':
include/linux/uaccess.h:33: error: dereferencing pointer to incomplete type
video_buf need PCI.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robert P. J. Day [Mon, 29 Jan 2007 21:19:50 +0000 (13:19 -0800)]
[PATCH] Fix "CONFIG_X86_64_" typo in drivers/kvm/svm.c
Fix what looks like an obvious typo in the file drivers/kvm/svm.c.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Acked-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix UML hostfs mknod(): userspace has differernt dev_t size and encoding
than kernel, so extract major/minor and reencode using glibc makedev()
macro.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org> Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serge E. Hallyn [Mon, 29 Jan 2007 21:19:40 +0000 (13:19 -0800)]
[PATCH] namespaces: fix exit race by splitting exit
Fix exit race by splitting the nsproxy putting into two pieces. First
piece reduces the nsproxy refcount. If we dropped the last reference, then
it puts the mnt_ns, and returns the nsproxy as a hint to the caller. Else
it returns NULL. The second piece of exiting task namespaces sets
tsk->nsproxy to NULL, and drops the references to other namespaces and
frees the nsproxy only if an nsproxy was passed in.
A little awkward and should probably be reworked, but hopefully it fixes
the NFS oops.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Cedric Le Goater <clg@fr.ibm.com> Cc: Daniel Hokka Zakrisson <daniel@hozac.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Gospodarek [Mon, 29 Jan 2007 20:08:38 +0000 (12:08 -0800)]
bonding: ARP monitoring broken on x86_64
While working with the latest bonding code I noticed a nasty problem that
will prevent arp monitoring from always functioning correctly on x86_64
systems. Comparing ints to longs and expecting reliable results on x86_64
is a bad idea. With this patch, arp monitoring works correctly again.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Stephen Hemminger <shemminger@osdl.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Sat, 27 Jan 2007 08:00:04 +0000 (00:00 -0800)]
82596 warning fixes
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1069: warning: cast from pointer to integer of different size
drivers/net/82596.c: In function 'i82596_probe':
drivers/net/82596.c:1249: warning: format '%d' expects type 'int', but argument 4 has type 'long unsigned int'
Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Vitaly Bordug [Sat, 27 Jan 2007 08:00:04 +0000 (00:00 -0800)]
FS_ENET: OF-related fixup for FEC and SCC MAC's
Updated direct resource pass with ioremap call, make it grant proper IRQ
mapping, stuff incompatible with the new approach were respectively put
under #ifndef CONFIG_PPC_MERGE. It is required so that both ppc and
powerpc could utilize fs_enet effectively.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The b44 chip occasionally needs to be reset when ISTAT_ERRORS are
encountered. The reset sequence includes a PHY reset that will take many
seconds to complete and cause the link to go down and up. By skipping the
PHY reset, it will greatly reduce the interruption when ISTAT_ERRORS are
encountered.
Change the full_reset parameter to reset_kind parameter in b44_init_hw().
This will allow PHY reset to be skipped when ISTAT_ERRORS are encountered.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 30 Jan 2007 08:59:18 +0000 (00:59 -0800)]
libata: fix translation for START STOP UNIT
libata's SCSI translation for the SCSI START STOP UNIT command with the
START bit clear (i.e. stopping the drive) appears to be incorrect. It
sends an ATA STANDBY command with the time period set to 0, which the code
comment says means "now", but the ATA standard says this means disable the
standby timer, which effectively does nothing. Change this to issue a
STANDBY IMMEDIATE command which will actually spin the drive down. The SAT
(SCSI/ATA Translation) standard revision 9 concurs with this choice.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
David Milburn [Tue, 30 Jan 2007 08:59:15 +0000 (00:59 -0800)]
libata-scsi: ata_task_ioctl should return ATA registers from sense data
User applications using the HDIO_DRIVE_TASK ioctl through libata expect
specific ATA registers to be returned to userspace. Verified that
ata_task_ioctl correctly returns register values to the smartctl
application.
Signed-off-by: David Milburn <dmilburn@redhat.com> Acked-by: Tejun Heo <htejun@gmail.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Tue, 30 Jan 2007 08:59:14 +0000 (00:59 -0800)]
pata_platform: set_mode fix
drivers/ata/pata_platform.c:85: warning: initialization from incompatible pointer type
Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
If word 53 bit 1 isn't set, the maximum PIO mode is indicated by
the upper 8 bits of word 51, not the lower 8 bits. Fixes PIO mode
detection on old Compact Flash cards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix PIO mode 1 overclocked taskfile transfers -- probably a typo carried over
from drivers/ide/pci/siimage.c where I've found it by documentation check...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jiri Kosina [Mon, 29 Jan 2007 11:44:41 +0000 (12:44 +0100)]
HID: fix pb_fnmode and move it to generic HID
The apple powerbook people are used to switch the pb_fnmode
setting at runtime through writing to sysfs, altering the
module parameter value. This was broken for them in 2.6.20-rc1
when generic HID layer was introduced, as the pb_fnmode flag
was made per-hiddevice, instead of global variable.
This patch moves the pb_fnmode module parameter from usbhid module
to hid module, but apart from that retains backward compatibility
with respect to changing the mode through sysfs.
Mike Christie [Tue, 30 Jan 2007 02:18:38 +0000 (21:18 -0500)]
[PATCH] Fix SG_IO timeout jiffy conversion
Commit 85e04e371b5a321b5df2bc3f8e0099a64fb087d7 cleaned up the timeout
conversion, but did it exactly the wrong way. We get msecs from user
space, and should convert them into jiffies. Not the other way around.
Here is a fix with the overflow check sg.c has added in. This fixes DVD
burnign with Nero.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[ "you'll be wanting a comma there" - Andrew ] Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 30 Jan 2007 00:37:38 +0000 (16:37 -0800)]
Fix balance_dirty_page() calculations with CONFIG_HIGHMEM
This makes balance_dirty_page() always base its calculations on the
amount of non-highmem memory in the machine, rather than try to base it
on total memory and then falling back on non-highmem memory if the
mapping it was writing wasn't highmem capable.
This not only fixes a situation where two different writers can have
wildly different notions about what is a "balanced" dirty state, but it
also means that people with highmem machines don't run into an OOM
situation when regular memory fills up with dirty pages.
We used to try to handle the latter case by scaling down the dirty_ratio
if the machine had a lot of highmem pages in page_writeback_init(), but
it wasn't aggressive enough for some situations, and since basing the
dirty ratio on highmem memory was broken in the first place, let's just
stop doing so.
(A variation of this theme fixed Justin Piszcz's OOM problem when
copying an 18GB file on a RAID setup).
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Justin Piszcz <jpiszcz@lucidpixels.com> Cc: Andrew Morton <akpm@osdl.org> Cc: Neil Brown <neilb@suse.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Christoph Lameter <clameter@sgi.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Adrian Bunk <bunk@stusta.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log