Jesper Juhl [Thu, 13 Dec 2007 22:53:08 +0000 (23:53 +0100)]
UBI: silence a warning
This patch silences the following warning :
drivers/mtd/ubi/vmt.c:73: warning: 'ret' may be used uninitialized in this function
gcc can't see that we always initialize ret in all situations where it is
actually used. The one case where it's not initialized is when we BUG(),
but gcc doesn't know that we won't then continue and use an uninitialized
'ret'.
This patch results in code that does exactely the same as before, but it
also makes gcc shut up, so we generate one less line of warning noise.
The idea of this interface belongs to Adrian Hunter. The
interface is extremely useful when one has to have a guarantee
that an LEB will contain all 0xFFs even in case of an unclean
reboot. UBI does have an 'ubi_leb_erase()' call which may do
this, but it is stupid and ineffecient, because it flushes whole
queue. I should be re-worked to just be a pair of unmap,
map calls.
First allocate the necessary eraseblocks, then the optional ones.
Otherwise it allocates all PEBs for bad EB handling, and fails
on then following EBA LEB allocation.
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem Bityutskiy [Thu, 18 Oct 2007 17:09:41 +0000 (20:09 +0300)]
UBI: fix error code in ubi_io_read()
When NAND detects an ECC error, it returns -EBADMSG. It does not
stop reading requested data if one page has an ECC error, it keeps
going and reads all the requested data. If it fails to read all
the data, it does not return -EBADMSG, but returns the error code
which reflects the reason of the failure.
But some drivers may have bugs (e.g., OneNAND had) and stop reading
after the first ECC error, so it returns -EBADMSG. In turn, UBI
propagates this up to the caller. The caller will treat this as
"all the requested data was read, but there was an ECC error".
So we change the error code to -EIO if it is -EBADMSG and the read
length is less then the requested length. We also add an assertion,
so if UBI debugging is enabled, UBI will bug.
Pointed-to-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
David Woodhouse [Mon, 3 Dec 2007 13:01:21 +0000 (13:01 +0000)]
[MTD] [NOR] Attempt to clean up the JEDEC unlock address confusion
Use a single unlock address, adjust it for the device type in the
knowledge that it'll be adjusted back again. This has the desirable
effect of masking out the least significant bit of the address for x16
devices.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Fri, 30 Nov 2007 16:24:52 +0000 (16:24 +0000)]
[MTD] [NOR] Fix overflow check in jedec_probe
Having laid the code out so that it's easier to read instead of sticking
to the 80-column guideline even when it doesn't make sense, a bug is
immediately spotted... we were only checking _one_ of the unlock
addresses to see if it runs off the end of the map.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Mon, 3 Dec 2007 12:48:57 +0000 (12:48 +0000)]
[MTD] [NOR] Clean up jedec_probe, remove unlock address arrays
This should have no functional effects -- we've been ignoring all but
the first address in the array for a long time, and using it only to
indicate which device types are supported.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Mon, 3 Dec 2007 12:46:12 +0000 (12:46 +0000)]
[MTD] Always initialise mutex in new mtd_blktrans_dev.
We were only initialising the mutex in the case where the new device was
automatically allocated the highest minor number. If the caller
specified a minor number, or if it filled in a free slot which was made
by a previous device deregistering, the mutex wouldn't get initialised
when we jumped out of the loop.
Reported by Monte Copeland <catboat@texas.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ben Dooks [Mon, 19 Nov 2007 23:28:07 +0000 (23:28 +0000)]
[MTD] [NAND] S3C2410 correctly set nFCE over resume
Ensure the nFCE line is de-asserted over suspend and
then re-initialised when the system resumes. This is
to ensure that the NAND is kept in lowest power mode
over suspend (power settings are only specified for
nFCE inactive) as well as fixing the Simtec Osiris
which relies on nFCE being inactive.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Stanislav Brabec [Mon, 19 Nov 2007 21:33:02 +0000 (22:33 +0100)]
[MTD] fix CONFIG_MTD_SHARP_SL if CONFIG_MTD=m
Sharp Zaurus SL-C3200 with CONFIG_MTD=m and CONFIG_MTD_SHARP_SL=y (as it
is bool) lost support for the ROM flash. With CONFIG_MTD=y it has no
problems.
It is caused by losing of compiled code of
drivers/mtd/maps/sharpsl-flash.o.
It was linked to drivers/mtd/maps/built-in.o and drivers/mtd/built-in.o,
but lost and not linked to drivers/built-in.o (because CONFIG_MTD!=y).
Patch below fixes this problem by creating sharpsl-flash.ko (and the
code works correctly as a module).
Signed-off-by: Stanislav Brabec <utx@penguin.cz> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
After writing to a Dataflash page, the built-in compare operation is
used to check that the page was successfully written. A logic bug in
checking the results of the comparison currently causes the compare to
never fail.
This bug was originally in the legacy at91_dataflash.c driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[MTD] [NOR] Prevent erase command invocation on suspended chip
while running stress tests we have met cfi_cmdset_0001.c driver issue.
Working on multipartitional devices with erase suspend on write
feature enabled it is possible to get erase operation invoked on chip
with suspended erase. get_chip() looses information about earlier
suspended erase and new erase operation gets issued. New erase
operations report successful completion, but blocks remain dirty
causing, for example, JFFS2 error messages like:
...
Newly-erased block contained word 0x20031985 at offset 0x00200000
Newly-erased block contained word 0x20031985 at offset 0x00280000
Newly-erased block contained word 0x20031985 at offset 0x00240000
...
The patch below fixes that issue.
Signed-off-by: Alexander Belyakov <alexander.belyakov@intel.com> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adrian Hunter [Tue, 6 Nov 2007 07:17:25 +0000 (09:17 +0200)]
[MTD] [OneNAND] Do not stop reading for ECC errors
When an ECC error occurs, the read should be completed
anyway before returning -EBADMSG. Returning -EBADMSG
straight away is incorrect.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Thu, 1 Nov 2007 20:27:38 +0000 (16:27 -0400)]
[JFFS2] Don't strip sgid bit from inode permissions
<viro> dwmw2: anyway, removing sgid from directories or from
files without S_IXGRP is a plain and simple bug
<viro> these days you don't need that logics at all - simply remove it
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Thu, 1 Nov 2007 20:25:56 +0000 (16:25 -0400)]
[JFFS2] Improve getdents vs. f_pos handling on NOR flash.
Commit a491486a2087ac3dfc00efb4f838c8d684afaf54 started obliterating
dirents directly on the medium, when jffs2_can_mark_obsolete(). Removing
them immediately from the f->dents list, however, screws up handling of
f_pos within a directory -- because the offset is equivalent to the
number of entries through the list we are, and the existence of
deletion dirents served to provide 'placeholders' for unlinked
entries. Now, 'rm -r' doesn't even manage to unlink everything in the
directory.
Revert to keeping 'deletion' dirents in the list, at least in memory
even though we no longer write anything to the medium.
Spotted, debugged and mostly fixed by Joakim Tjernlund
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Convert CFI tables from Atmel cmdset_0001 chips to Intel format and set
BufWrite timeouts to 0 for Atmel cmdset_0001 and cmdset_0002 chips.
Some chips may indicate support for buffered writes even though they
only support dual-word writes.
The CFI fixup must run before fixup_use_write_buffers for this to work.
Signed-off-by: Håvard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use of_get_next_child for proper ref counting as suggested by Stephen Rothwell
and remove add_mtd_partitions from parse_partitions to avoid duplicate
mtd device registration for RedBoot partitions.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Heckled-for-on-IRC-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ken'ichi Ohmichi [Fri, 26 Oct 2007 05:19:26 +0000 (14:19 +0900)]
x86: Dump filtering supports x86_64 sparsemem
This patch adds the symbol "init_level4_pgt" to the vmcoreinfo data so
that makedumpfile (dump filtering command) supports x86_64 sparsemem
kernel of linux-2.6.24.
makedumpfile creates a small dumpfile by excluding unnecessary pages for
the analysis. It checks attributes in page structures and distinguishes
necessary pages and unnecessary ones. To check them, makedumpfile gets
the vmcoreinfo data which has the minimum debugging information only for
dump filtering.
For older x86_64 kernel (linux-2.6.23 or before), makedumpfile translates
the virtual address of page structure into physical address by subtracting
PAGE_OFFSET from virtual address, but this translation isn't effective for
linux-2.6.24 sparsemem kernel, because its page structures are in virtual
memmap area. makedumpfile should translate their virtual address by 4-levels
paging and it needs the symbol "init_level4_pgt".
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel only ever supports 1 version of the boot protocol
so there is no need to check the boot protocol revision to
see if a feature is supported.
Both x86 and x86_64 support the same boot protocol so we need
to implement the KEEP_SEGMENTS on x86_64 as well. It isn't
just paravirt bootloaders that could use this functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Vivek Goyal <vgoyal@in.ibm.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Zachary Amsden <zach@vmware.com> Cc: Andi Kleen <ak@suse.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
James Bottomley [Fri, 26 Oct 2007 17:17:19 +0000 (12:17 -0500)]
x86: voyager: fix bogus conversion to per_cpu for boot_cpu_info
There were two problems. Firstly, someone forgot the struct keyword in
front of cpuinfo_x86, so I take it this wasn't even compile checked.
Secondly, the actual definition has this as a SHARED_ALIGNED, so the
definitions mismatch.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sat, 27 Oct 2007 17:14:04 +0000 (10:14 -0700)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6:
[JFFS2] Update MAINTAINERS entry -- the jffs-dev list is dead
[JFFS2] Prevent return of initialised variable in jffs2_init_acl_post()
Linus Torvalds [Sat, 27 Oct 2007 17:12:39 +0000 (10:12 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc_spi: Fix mmc-over-spi regression
mmc: use common byte swap macros
mmc: fix cid and csd byte order
at91_mci: Fix bad reference
This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Herbert Xu [Sat, 27 Oct 2007 07:52:07 +0000 (00:52 -0700)]
[CRYPTO] users: Fix up scatterlist conversion errors
This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion. It also adds a few conversions that were
missing altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The pid namespace patches changed the semantics of
find_task_by_pid without breaking the compile resulting
in get_net_ns_by_pid doing the wrong thing.
So switch to using the intended find_task_by_vpid.
Combined with Denis' earlier patch to make netlink traffic
fully synchronous the inadvertent race I introduced with
accessing current is actually removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[NET]: Marking struct pernet_operations __net_initdata was inappropriate
It is not safe to to place struct pernet_operations in a special section.
We need struct pernet_operations to last until we call unregister_pernet_subsys.
Which doesn't happen until module unload.
So marking struct pernet_operations is a disaster for modules in two ways.
- We discard it before we call the exit method it points to.
- Because I keep struct pernet_operations on a linked list discarding
it for compiled in code removes elements in the middle of a linked
list and does horrible things for linked insert.
So this looks safe assuming __exit_refok is not discarded
for modules.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Sat, 27 Oct 2007 05:53:58 +0000 (22:53 -0700)]
[INET] ESP: Must #include <linux/scatterlist.h>
This patch fixes the following compile errors in some configurations:
<-- snip -->
...
CC net/ipv4/esp4.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv4/esp4.c: In function 'esp_output':
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv4/esp4.c:113: error: implicit declaration of function 'sg_init_table'
make[3]: *** [net/ipv4/esp4.o] Error 1
...
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv6/esp6.c: In function 'esp6_output':
/home/bunk/linux/kernel-2.6/git/linux-2.6/net/ipv6/esp6.c:112: error: implicit declaration of function 'sg_init_table'
make[3]: *** [net/ipv6/esp6.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Sat, 27 Oct 2007 05:53:14 +0000 (22:53 -0700)]
[TCP] IPV6: fix softnet build breakage
net/ipv6/tcp_ipv6.c: In function 'tcp_v6_rcv':
net/ipv6/tcp_ipv6.c:1736: error: implicit declaration of function
'get_softnet_dma'
net/ipv6/tcp_ipv6.c:1736: warning: assignment makes pointer from integer
without a cast
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 26 Oct 2007 20:56:01 +0000 (13:56 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
x86 setup: sizeof() is unsigned, unbreak comparisons
x86 setup: handle boot loaders which set up the stack incorrectly
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/x86:
x86: kill the old i386 and x86_64 directories
x86: move i386 and x86_64 Kconfig files to x86 directory
kconfig: small code refactoring in kconfig Makefile
x86: unification of i386 and x86_64 Kconfig.debug
x86: move defconfig files for i386 and x86_64 to x86
x86: move i386 and x86_64 Makefiles to arch/x86
drivers/ide/pci/generic: fix build for CONFIG_HOTPLUG=n
It turns out that const and __{dev}initdata cannot be mixed currently
and that generic IDE PCI host driver is also affected by the same issue:
On Thursday 25 October 2007, Ralf Baechle wrote:
> CC drivers/ide/pci/generic.o
> drivers/ide/pci/generic.c:52: error: __setup_str_ide_generic_all_on causes a
> +section type conflict
[ Also reported by Martijn Uffing <mp3project@sarijopen.student.utwente.nl>. ]
This patch workarounds the problem in a bit hackish way but without
removing const from generic_chipsets[] (it adds const to __setup() so
__setup_str_ide_generic_all becomes const).
Now all __{dev}initdata data in generic IDE PCI host driver are read-only
so it builds again (driver's .init.data section gets marked as READONLY).
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279a2521075250fad682ca0acc10d4fd7
>
> Bisected to:
> 8562043606430185cad26d085d46adcc7ad67fd1 is first bad commit
> commit 8562043606430185cad26d085d46adcc7ad67fd1
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that hpt366 host driver is also affected by the same issue:
> drivers/ide/pci/hpt366.c:1428: error: hpt366_chipsets causes a section type
> conflict
This patch workarounds the problem by making static struct hpt_info instances
const. Now all __devinitdata data in hpt366 host driver are read-only so it
builds again (driver's .init.data section gets marked as READONLY).
While at it:
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: "Avuton Olrich" <avuton@gmail.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279a2521075250fad682ca0acc10d4fd7
>
> Bisected to:
> 8562043606430185cad26d085d46adcc7ad67fd1 is first bad commit
> commit 8562043606430185cad26d085d46adcc7ad67fd1
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently.
This patch workarounds the problem by removing __devinitdata tag from 'primary'
variable (which makes 'primary' to be moved from .init.data to .bss section).
Now all __devinitdata data in cy82c693 host driver are read-only so it builds
again (driver's .init.data section gets marked as READONLY).
While at it:
* Move 'primary' variable to its only user, init_iops_cy82c693().
1) Patch doesn't change any code here, so gcc is already smart enough
to "feel" constness in such simple functions.
2) There is no such thing as const task_struct. Anyone who think
otherwise deserves compiler warning.
Paul Moore [Fri, 26 Oct 2007 11:29:08 +0000 (04:29 -0700)]
[NetLabel]: correct usage of RCU locking
This fixes some awkward, and perhaps even problematic, RCU lock usage in the
NetLabel code as well as some other related trivial cleanups found when
looking through the RCU locking. Most of the changes involve removing the
redundant RCU read locks wrapping spinlocks in the case of a RCU writer.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ryousei Takano [Fri, 26 Oct 2007 11:27:59 +0000 (04:27 -0700)]
[TCP]: fix D-SACK cwnd handling
In the current net-2.6 kernel, handling FLAG_DSACKING_ACK is broken.
The flag is cleared to 1 just after FLAG_DSACKING_ACK is set.
if (found_dup_sack)
flag |= FLAG_DSACKING_ACK;
:
flag = 1;
To fix it, this patch introduces a part of the tcp_sacktag_state patch:
http://marc.info/?l=linux-netdev&m=119210560431519&w=2
Signed-off-by: Ryousei Takano <takano-ryousei@aist.go.jp> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
[NET] napi: use non-interruptible sleep in napi_disable
The current napi_disable() uses msleep_interruptible() but doesn't
(and can't) exit in case there's a signal, thus ending up doing a
hot spin without a cpu_relax. Use uninterruptible sleep instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Fri, 26 Oct 2007 10:55:44 +0000 (03:55 -0700)]
[NET] fs/proc/proc_net.c: make a struct static
Struct proc_net_ns_ops can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[NET] dev_change_name: ignore changes to same name
Prevent error/backtrace from dev_rename() when changing
name of network device to the same name. This is a common
situation with udev and other scripts that bind addr to device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Fri, 26 Oct 2007 09:49:09 +0000 (02:49 -0700)]
[NET]: Document some simple rules for actions
This patch adds documentation on what is expected of an
action which branches away from the action-graph or when it
needs to trample on actins. It also describes what is expected of
users of such actions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Fri, 26 Oct 2007 09:47:23 +0000 (02:47 -0700)]
[NET_CLS_ACT]: Introduce skb_act_clone
Reworked skb_clone looks uglier with the single ifdef
CONFIG_NET_CLS_ACT This patch introduces skb_act_clone which will
replace skb_clone in tc actions
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log