Jason Parekh [Fri, 17 Nov 2006 06:05:58 +0000 (01:05 -0500)]
Input: appletouch - verious updates for MacBooks
Change a bit the finger detection method used by the appletouch
driver to reduce touchpad "jumpiness":
- Adjust the method for detecting multiple fingers. Previously, it
recognized a new finger when a low sensor reading is followed by
a high sensor reading. The new method checks for 'humps' in the
sensor readings, so there doesn't necessarily have to be a low
sensor between two high sensors for two fingers to be triggered.
This allows detecting presence of two fingers on the touchpad
even when they touch each other.
- Change absolute coordinate calculation to us to get rid of "jumps".
Instead of using full value from a sensor once it passes the
threshold subtract theshold value from the reading.
- Allow adjusting threshold value via module parameter.
The patch doesn't seem to affect the Powerbooks but does greatly improve
the touchpad behaviour on the MacBooks.
Signed-off-by: Jason Parekh <jasonparekh@gmail.com> Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Anssi Hannula [Sun, 5 Nov 2006 03:49:53 +0000 (22:49 -0500)]
Input: HID - add a quirk for the Logitech USB Receiver
Logitech USB Receiver (046d:c101) has two interfaces. The first one
contains fields from HID_UP_KEYBOARD and HID_UP_LED, and the other one
contains fields from HID_UP_CONSUMER and HID_UP_LOGIVENDOR. This device
is used with multiple wireless Logitech products, including UltraX Media
Remote.
All fields on both interfaces are either keys or leds. All fields in the
first interface are marked as Absolute, while the fields in the second
interface are marked as Relative. Marking the keys as relative causes
hidinput_hid_event() to send release events right after key press
events.
The device has EV_REP set, so the userspace expects the device to send
repeat events if a key is held down. However, as hidinput_hid_event()
sends release events immediately, repeat events are not sent at all. In
fact, the userspace has no way of knowing if a key is being held down.
Fix this by adding a quirk for 046d:c101 which changes relative keys to
absolute ones.
Linus Torvalds [Sat, 4 Nov 2006 21:03:00 +0000 (13:03 -0800)]
Make sure "user->sigpending" count is in sync
The previous commit (45c18b0bb579b5c1b89f8c99f1b6ffa4c586ba08, aka "Fix
unlikely (but possible) race condition on task->user access") fixed a
potential oops due to __sigqueue_alloc() getting its "user" pointer out
of sync with switch_user(), and accessing a user pointer that had been
de-allocated on another CPU.
It still left another (much less serious) problem, where a concurrent
__sigqueue_alloc and swich_user could cause sigqueue_alloc to do signal
pending reference counting for a _different_ user than the one it then
actually ended up using. No oops, but we'd end up with the wrong signal
accounting.
Another case of Oleg's eagle-eyes picking up the problem.
This is trivially fixed by just making sure we load whichever "user"
structure we decide to use (it doesn't matter _which_ one we pick, we
just need to pick one) just once.
Linus Torvalds [Sat, 4 Nov 2006 18:06:02 +0000 (10:06 -0800)]
Fix unlikely (but possible) race condition on task->user access
There's a possible race condition when doing a "switch_uid()" from one
user to another, which could race with another thread doing a signal
allocation and looking at the old thread ->user pointer as it is freed.
This explains an oops reported by Lukasz Trabinski:
http://permalink.gmane.org/gmane.linux.kernel/462241
We fix this by delaying the (reference-counted) freeing of the user
structure until the thread signal handler lock has been released, so
that we know that the signal allocation has either seen the new value or
has properly incremented the reference count of the old one.
Linus Torvalds [Sat, 4 Nov 2006 17:55:00 +0000 (09:55 -0800)]
Revert unintentional "volatile" changes in ipc/msg.c
Commit 5a06a363ef48444186f18095ae1b932dddbbfa89 ("[PATCH] ipc/msg.c:
clean up coding style") breaks fakeroot on Alpha (variously hangs or
oopses), according to a report by Falk Hueffner.
The fact that the code seems to rely on compiler access ordering through
the use of "volatile" is a pretty certain sign that the code has locking
problems, and we should fix those properly and then remove the whole
"volatile" entirely.
But in the meantime, the movement of "volatile" was unintentional, and
should be reverted.
Jens Axboe [Sat, 4 Nov 2006 11:49:32 +0000 (12:49 +0100)]
[PATCH] splice: fix problem introduced with inode diet
After the inode slimming patch that unionised i_pipe/i_bdev/i_cdev, it's
no longer enough to check for existance of ->i_pipe to verify that this
is a pipe.
Original patch from Eric Dumazet <dada1@cosmosbay.com>
Final solution suggested by Linus.
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: use MII hooks only if CONFIG_MII is enabled
USB Storage: unusual_devs.h entry for Sony Ericsson P990i
USB: xpad: additional USB id's added
USB: fix compiler issues with newer gcc versions
USB: HID: add blacklist AIRcable USB, little beautification
USB: usblp: fix system suspend for some systems
USB: failure in usblp's error path
usbtouchscreen: use endpoint address from endpoint descriptor
USB: sierra: Fix id for Sierra Wireless MC8755 in new table
USB: new VID/PID-combos for cp2101
hid-core: big-endian fix fix
USB: usb-storage: Unusual_dev update
USB: add another sierra wireless device id
[PATCH] Fix user.* xattr permission check for sticky dirs
The user.* extended attributes are only allowed on regular files and
directories. Sticky directories further restrict write access to the owner
and privileged users. (See the attr(5) man page for an explanation.)
The original check in ext2/ext3 when user.* xattrs were merged was more
restrictive than intended, and when the xattr permission checks were moved
into the VFS, read access to user.* attributes on sticky directores ended
up being denied in addition.
Originally-from: Gerard Neil <xyzzy@devferret.org> Signed-off-by: Andreas Gruenbacher <agruen@suse.de> Cc: Dave Kleikamp <shaggy@austin.ibm.com> Cc: Jan Engelhardt <jengelh@linux01.gwdg.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Fix sys_move_pages when a NULL node list is passed
sys_move_pages() uses vmalloc() to allocate an array of structures that is
fills with information passed from user mode and then passes to
do_stat_pages() (in the case the node list is NULL). do_stat_pages()
depends on a marker in the node field of the structure to decide how large
the array is and this marker is correctly inserted into the last element of
the array. However, vmalloc() doesn't zero the memory it allocates and if
the user passes NULL for the node list, then the node fields are not filled
in (except for the end marker). If the memory the vmalloc() returned
happend to have a word with the marker value in it in just the right place,
do_pages_stat will fail to fill the status field of part of the array and
we will return (random) kernel data to user mode.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Fri, 3 Nov 2006 06:07:23 +0000 (22:07 -0800)]
[PATCH] uml: include tidying
In order to get the __NR_* constants, we need sys/syscall.h.
linux/unistd.h works as well since it includes syscall.h, however syscall.h
is more parsimonious. We were inconsistent in this, and this patch adds
syscall.h includes where necessary and removes linux/unistd.h includes
where they are not needed.
asm/unistd.h also includes the __NR_* constants, but these are not the
glibc-sanctioned ones, so this also removes one such inclusion.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Fri, 3 Nov 2006 06:07:22 +0000 (22:07 -0800)]
[PATCH] uml: fix I/O hang
Fix a UML hang in which everything would just stop until some I/O happened
- a ping, someone whacking the keyboard - at which point everything would
start up again as though nothing had happened.
The cause was gcc reordering some code which absolutely needed to be
executed in the order in the source. When unblock_signals switches signals
from off to on, it needs to see if any interrupts had happened in the
critical section. The interrupt handlers check signals_enabled - if it is
zero, then the handler adds a bit to the "pending" bitmask and returns.
unblock_signals checks this mask to see if any signals need to be
delivered.
The crucial part is this:
signals_enabled = 1;
save_pending = pending;
if(save_pending == 0)
return;
pending = 0;
In order to avoid an interrupt arriving between reading pending and setting
it to zero, in which case, the record of the interrupt would be erased,
signals are enabled.
What happened was that gcc reordered this so that 'save_pending = pending'
came before 'signals_enabled = 1', creating a one-instruction window within
which an interrupt could arrive, set its bit in pending, and have it be
immediately erased.
When the I/O workload is purely disk-based, the loss of a block device
interrupt stops the entire I/O system because the next block request will
wait for the current one to finish. Thus the system hangs until something
else causes some I/O to arrive, such as a network packet or console input.
The fix to this particular problem is a memory barrier between enabling
signals and reading the pending signal mask. An xchg would also probably
work.
Looking over this code for similar problems led me to do a few more
things:
- make signals_enabled and pending volatile so that they don't get cached
in registers
- add an mb() to the return paths of block_signals and unblock_signals so
that the modification of signals_enabled doesn't get shuffled into the
caller in the event that these are inlined in the future.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Mahoney [Fri, 3 Nov 2006 06:07:20 +0000 (22:07 -0800)]
[PATCH] reiserfs: reset errval after initializing bitmap cache
Callers after reiserfs_init_bitmap_cache() expect errval to contain -EINVAL
until much later. If a condition fails before errval is reset later,
reiserfs_fill_super() will mistakenly return 0, causing an Oops in
do_add_mount(). This patch resets errval to -EINVAL after the call.
I view this as a temporary fix and real error codes should be used
throughout reiserfs_fill_super().
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Fri, 3 Nov 2006 06:07:20 +0000 (22:07 -0800)]
[PATCH] spi section fix
WARNING: vmlinux - Section mismatch: reference to .init.text:spi_register_board_info from __ksymtab_gpl between '__ksymtab_spi_register_board_info' (at offset 0xc032f7d0) and '__ksymtab_spi_alloc_master'
Fix this by removing the export.
Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a swsusp debugging mode. This does everything that's needed for a suspend
except for actually suspending. So we can look in the log messages and work
out a) what code is being slow and b) which drivers are misbehaving.
Andrew Morton [Fri, 3 Nov 2006 06:07:18 +0000 (22:07 -0800)]
[PATCH] acpi_noirq section fix
WARNING: vmlinux - Section mismatch: reference to .init.data:acpi_noirq from .text between 'pcibios_penalize_isa_irq' (at offset 0xc026ffa1) and 'pirq_serverworks_get'
Daniel Yeisley [Fri, 3 Nov 2006 06:07:14 +0000 (22:07 -0800)]
[PATCH] init_reap_node() initialization fix
It looks like there is a bug in init_reap_node() in slab.c that can cause
multiple oops's on certain ES7000 configurations. The variable reap_node
is defined per cpu, but only initialized on a single CPU. This causes an
oops in next_reap_node() when __get_cpu_var(reap_node) returns the wrong
value. Fix is below.
Signed-off-by: Dan Yeisley <dan.yeisley@unisys.com> Cc: Andi Kleen <ak@suse.de> Acked-by: Christoph Lameter <clameter@engr.sgi.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Yvan Seth [Fri, 3 Nov 2006 06:07:13 +0000 (22:07 -0800)]
[PATCH] ipmi_si_intf.c sets bad class_mask with PCI_DEVICE_CLASS
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7439
It looks like device registration in drivers/char/ipmi/ipmi_si_intf.c was
cleaned up and a small error was made when setting the class_mask. The fix
is simple as the correct mask value is defined in the code but is not used.
Srinivasa Ds [Fri, 3 Nov 2006 06:07:12 +0000 (22:07 -0800)]
[PATCH] NFS4: fix for recursive locking problem
When I was performing some operations on NFS, I got below error on server
side.
=============================================
[ INFO: possible recursive locking detected ]
2.6.19-prep #1
---------------------------------------------
nfsd4/3525 is trying to acquire lock:
(&inode->i_mutex){--..}, at: [<c0611e5a>] mutex_lock+0x21/0x24
but task is already holding lock:
(&inode->i_mutex){--..}, at: [<c0611e5a>] mutex_lock+0x21/0x24
other info that might help us debug this:
2 locks held by nfsd4/3525:
#0: (client_mutex){--..}, at: [<c0611e5a>] mutex_lock+0x21/0x24
#1: (&inode->i_mutex){--..}, at: [<c0611e5a>] mutex_lock+0x21/0x24
Cause for this problem was,2 successive mutex_lock calls on 2 diffrent inodes ,as shown below
static int
nfsd4_clear_clid_dir(struct dentry *dir, struct dentry *dentry)
{
int status;
/* For now this directory should already be empty, but we empty it of
* any regular files anyway, just in case the directory was created by
* a kernel from the future.... */
nfsd4_list_rec_dir(dentry, nfsd4_remove_clid_file);
mutex_lock(&dir->d_inode->i_mutex);
status = vfs_rmdir(dir->d_inode, dentry);
...
int vfs_rmdir(struct inode *dir, struct dentry *dentry)
{
int error = may_delete(dir, dentry, 1);
if (error)
return error;
if (!dir->i_op || !dir->i_op->rmdir)
return -EPERM;
DQUOT_INIT(dir);
mutex_lock(&dentry->d_inode->i_mutex);
...
So I have developed the patch to overcome this problem.
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com> Cc: Neil Brown <neilb@suse.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
OGAWA Hirofumi [Fri, 3 Nov 2006 06:07:06 +0000 (22:07 -0800)]
[PATCH] Cleanup read_pages()
Current read_pages() assume ->readpages() frees the passed pages.
This patch free the pages in ->read_pages(), if those were remaining in the
pages_list. So, readpages() just can ignore the remaining pages in
pages_list.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: Steven French <sfrench@us.ibm.com> Cc: Miklos Szeredi <miklos@szeredi.hu> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy Dunlap [Fri, 3 Nov 2006 06:07:06 +0000 (22:07 -0800)]
[PATCH] lkdtm: cleanup headers and module_param/MODULE_PARM_DESC
Fix module_param/sysfs file permission typo.
Clean up MODULE_PARM_DESC strings to avoid fancy (and incorrect)
formatting.
Fix header includes for lkdtm; add some needed ones, remove unused ones;
and fix this gcc warning:
drivers/misc/lkdtm.c:150: warning: 'struct buffer_head' declared inside parameter list
drivers/misc/lkdtm.c:150: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Ankita Garg <ankita@in.ibm.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eric Sandeen [Fri, 3 Nov 2006 06:07:05 +0000 (22:07 -0800)]
[PATCH] fix UFS superblock alignment issues
ufs2 fails to mount on x86_64, claiming bad magic. This is because
ufs_super_block_third's fs_un1 member is padded out by 4 bytes for 8-byte
alignment, pushing down the rest of the struct.
Forcing this to be packed solves it. I took a quick look over other
on-disk structures and didn't immediately find other problems. I was able
to mount & ls a populated ufs2 filesystem w/ this change.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Cc: Evgeniy Dushistov <dushistov@mail.ru> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Emelianov [Fri, 3 Nov 2006 06:07:03 +0000 (22:07 -0800)]
[PATCH] Fix ipc entries removal
Fix two issuses related to ipc_ids->entries freeing.
1. When freeing ipc namespace we need to free entries allocated
with ipc_init_ids().
2. When removing old entries in grow_ary() ipc_rcu_putref()
may be called on entries set to &ids->nullentry earlier in
ipc_init_ids().
This is almost impossible without namespaces, but with
them this situation becomes possible.
Found during OpenVZ testing after obvious leaks in beancounters.
Signed-off-by: Pavel Emelianov <xemul@openvz.org> Cc: Kirill Korotaev <dev@openvz.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Heiko Carstens [Fri, 3 Nov 2006 06:06:58 +0000 (22:06 -0800)]
[PATCH] sys_pselect7 vs compat_sys_pselect7 uaccess error handling
758333458aa719bfc26ec16eafd4ad3a9e96014d fixes the not checked copy_to_user
return value of compat_sys_pselect7. I ran into this too because of an old
source tree, but my fix would look quite a bit different to Andi's fix.
The reason is that the compat function IMHO should behave the very same as
the non-compat function if possible. Since sys_pselect7 does not return
-EFAULT in this specific case, change the compat code so it behaves like
sys_pselect7.
Cc: David Woodhouse <dwmw2@infradead.org> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell [Thu, 2 Nov 2006 20:29:12 +0000 (12:29 -0800)]
USB: use MII hooks only if CONFIG_MII is enabled
Fix mcs7830 patch
The recent mcs7830 update to make the MII support sharable goofed various
pre-existing configurations in two ways:
- it made the usbnet infrastructure reference MII symbols even
when they're not needed in the kernel being built
- it didn't enable MII along with the mcs7830 minidriver
This patch fixes these two problems.
However, there does seem to be a Kconfig reverse dependency bug in that MII
gets wrongly enabled in some cases (like USBNET=y and USBNET_MII=n); I think
I've noticed that same problem in other situations too. So the result can
mean kernels being bloated by stuff that's needlessly enabled ... better
than wrongly being disabled, but contributing to bloat.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: HID: add blacklist AIRcable USB, little beautification
This patch add AIRcable USBto USB-HID blacklist, makes some little
changes things in the Kconfig to make AIRcable USB look as all the rest
of drivers. And it removes the readme part that was on
Documentation/usb/usb-serial.txt because it is not needed anymore.
Signed-off-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Ritz [Fri, 27 Oct 2006 20:46:03 +0000 (22:46 +0200)]
usbtouchscreen: use endpoint address from endpoint descriptor
use the endpoint address from the endpoint descriptor instead of the hardcoding
it to 0x81. at least some ITM based screen use a different address and don't work
without this.
Jan Luebbe [Fri, 27 Oct 2006 16:59:24 +0000 (18:59 +0200)]
USB: sierra: Fix id for Sierra Wireless MC8755 in new table
The new version of sierra.c has introduced tables for the 1 port and 3
port variants. The device id i added in my last patch needs to be added
to the 3 port table.
Signed-off-by: Jan Luebbe <jluebbe@lasnet.de> Cc: Kevin Lloyd <linux@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bjorn Schneider [Sat, 28 Oct 2006 10:42:04 +0000 (12:42 +0200)]
USB: new VID/PID-combos for cp2101
3 new VID/PID combinations (registered with Silicon Laboratories Inc.)
added for devices made by Lipowsky Industrie Elektronik GmbH all using
the CP2102 usb-to-serial converter (Baby-JTAG, Baby-LIN, HARP-1).
Grant Grundler [Thu, 19 Oct 2006 22:09:51 +0000 (15:09 -0700)]
hid-core: big-endian fix fix
Adam Kropelin had posted 32-bit fix in June 2005 about two weeks after I
originally had posted my fixes for big endian support. Adam has a UPS
device which reports LINEV using 32-bits.
Added comments to describe the limitations of the code.
extract() is the same version I posted earlier and tested in user space.
Made similar changes to implement() routine. I've written (and will
shortly post) a test for implement(). Code tested on C3600 (parisc) with
USB keyboard/mouse attached.
I've dropped test_implement.c and a few other user space test programs on
http://iou.parisc-linux.org/~grundler/tests/
Phil Dibowitz [Thu, 19 Oct 2006 07:11:17 +0000 (00:11 -0700)]
USB: usb-storage: Unusual_dev update
The protocol in this entry is needed for some versions of the device but
not others. This adds the NEED_OVERRIDE flag to prevent it complaining
to users who don't need it.
Adrian Bunk [Fri, 27 Oct 2006 23:12:30 +0000 (16:12 -0700)]
PCI: Let PCI_MULTITHREAD_PROBE depend on BROKEN
PCI_MULTITHREAD_PROBE is an interesting feature, but in its current state
it seems to be more of a trap for users who accidentally enable it.
This patch lets PCI_MULTITHREAD_PROBE depend on BROKEN for 2.6.19.
The intention is to get this patch reversed in -mm as soon as it's in
Linus' tree, and reverse it for 2.6.20 or 2.6.21 after the fallout of
in-kernel problems PCI_MULTITHREAD_PROBE causes got fixed.
(akpm: I get enough bug reports already)
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dmitry Torokhov [Fri, 3 Nov 2006 04:27:49 +0000 (23:27 -0500)]
Input: i8042 - remove unneeded call to i8042_interrupt()
Remove call to i8042_interrupt() from i8042_aux_write(). According
to Vojtech it may cause problems with older controllers if it is
called right after real interrupt. Also it is not needed anymore
since we register IRQs early and not waiting for serio ports to
be opened.
This adds another DMI detected touchscreen. It is exactly the same
driver as the existing ones, but this allows it to be detected on the
Hitachi Flora-IE 55mi tablet. The original Midori drivers are "abeo
antiquus". This should allow new life for these machines.
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] report rename failure when target file is locked by Windows
[CIFS] Allow null user connections
[CIFS] Fix readdir breakage when blocksize set too small
Linus Torvalds [Thu, 2 Nov 2006 22:36:05 +0000 (14:36 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/addr: Use client registration to fix module unload race
IB/mthca: Fix MAD extended header format for MAD_IFC firmware command
IB/uverbs: Return sq_draining value in query_qp response
IB/amso1100: Fix incorrect pr_debug()
IB/amso1100: Use dma_alloc_coherent() instead of kmalloc/dma_map_single
IB/ehca: Fix eHCA driver compilation for uniprocessor
RDMA/cma: rdma_bind_addr() leaks a cma_dev reference count
IB/iser: Start connection after enabling iSER
Linus Torvalds [Thu, 2 Nov 2006 18:14:37 +0000 (10:14 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Do not use -msym32 option for modules.
[MIPS] Don't use R10000 llsc workaround version for all llsc-full processors.
[MIPS] Ocelot G: Fix : "CURRENTLY_UNUSED" is not defined warning.
[MIPS] Fix warning about init_initrd() call if !CONFIG_BLK_DEV_INITRD.
[MIPS] IP27: Allow SMP ;-) Another changeset messed up by patch.
[MIPS] Fix merge screwup by patch(1)
Revert "[MIPS] Make SPARSEMEM selectable on QEMU."
Ralf Baechle [Mon, 30 Oct 2006 12:48:04 +0000 (12:48 +0000)]
[MIPS] Ocelot G: Fix : "CURRENTLY_UNUSED" is not defined warning.
CC arch/mips/momentum/ocelot_g/gt-irq.o
arch/mips/momentum/ocelot_g/gt-irq.c:30:5: warning: "CURRENTLY_UNUSED" is not defined
arch/mips/momentum/ocelot_g/gt-irq.c:199:5: warning: "CURRENTLY_UNUSED" is not defined
Another amazing example of patch(1) messing up - lmo changeset 66e8560d11d02bcadc261498471831a6375ad046 was merged twice to kernel.org
and ended up doing this rubbish job.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: silence a warning in ebtables
[IPV6]: File the fingerprints off ah6->spi/esp6->spi
[TCP]: Set default congestion control when no sysctl.
[TIPC] net/tipc/port.c: fix NULL dereference
Dave Kleikamp [Thu, 2 Nov 2006 16:50:40 +0000 (10:50 -0600)]
JFS: Remove redundant xattr permission checking
The vfs handles most permissions for setting and retrieving xattrs.
This patch removes a redundant and wrong check so that it won't override
the correct behavior which is being fixed in the vfs.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Meelis Roos [Thu, 2 Nov 2006 02:07:27 +0000 (18:07 -0800)]
[NETFILTER]: silence a warning in ebtables
net/bridge/netfilter/ebtables.c: In function 'ebt_dev_check':
net/bridge/netfilter/ebtables.c:89: warning: initialization discards qualifiers from pointer target type
So make the char* a const char * and the warning is gone.
Signed-off-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
I copied the logic from ll/sc arch implementations, but that
was wrong and makes no sense at all. Just do a straight
compare-exchange instruction, just like x86.
Based upon bug reports from Dennis Gilmore and Fabio Massimo.
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log