From: Ivo van Doorn Date: Tue, 2 Dec 2008 17:20:42 +0000 (+0100) Subject: rt2x00: Implement HW encryption (rt2500usb) X-Git-Tag: v2.6.29-rc1~581^2~305^2~19 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=dddfb478b26e29a2b47f655ec219e743b8111015;p=linux-2.6-omap-h63xx.git rt2x00: Implement HW encryption (rt2500usb) rt2500usb supports hardware encryption. rt2500usb supports up to 4 shared and pairwise keys. Signed-off-by: Ivo van Doorn Signed-off-by: John W. Linville --- diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig index 95511ac2247..178b313293b 100644 --- a/drivers/net/wireless/rt2x00/Kconfig +++ b/drivers/net/wireless/rt2x00/Kconfig @@ -57,6 +57,7 @@ config RT2500USB tristate "Ralink rt2500 (USB) support" depends on USB select RT2X00_LIB_USB + select RT2X00_LIB_CRYPTO ---help--- This adds support for rt2500 wireless chipset family. Supported chips: RT2571 & RT2572. diff --git a/drivers/net/wireless/rt2x00/rt2500usb.c b/drivers/net/wireless/rt2x00/rt2500usb.c index 0447e93306a..90bf0b96caa 100644 --- a/drivers/net/wireless/rt2x00/rt2500usb.c +++ b/drivers/net/wireless/rt2x00/rt2500usb.c @@ -35,6 +35,13 @@ #include "rt2x00usb.h" #include "rt2500usb.h" +/* + * Allow hardware encryption to be disabled. + */ +static int modparam_nohwcrypt = 1; +module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO); +MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); + /* * Register access. * All access to the CSR registers will go through the methods @@ -323,6 +330,82 @@ static void rt2500usb_init_led(struct rt2x00_dev *rt2x00dev, /* * Configuration handlers. */ + +/* + * rt2500usb does not differentiate between shared and pairwise + * keys, so we should use the same function for both key types. + */ +static int rt2500usb_config_key(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key) +{ + int timeout; + u32 mask; + u16 reg; + + if (crypto->cmd == SET_KEY) { + /* + * Pairwise key will always be entry 0, but this + * could collide with a shared key on the same + * position... + */ + mask = TXRX_CSR0_KEY_ID.bit_mask; + + rt2500usb_register_read(rt2x00dev, TXRX_CSR0, ®); + reg &= mask; + + if (reg && reg == mask) + return -ENOSPC; + + reg = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID); + + key->hw_key_idx += reg ? ffz(reg) : 0; + + /* + * The encryption key doesn't fit within the CSR cache, + * this means we should allocate it seperately and use + * rt2x00usb_vendor_request() to send the key to the hardware. + */ + reg = KEY_ENTRY(key->hw_key_idx); + timeout = REGISTER_TIMEOUT32(sizeof(crypto->key)); + rt2x00usb_vendor_request_large_buff(rt2x00dev, USB_MULTI_WRITE, + USB_VENDOR_REQUEST_OUT, reg, + crypto->key, + sizeof(crypto->key), + timeout); + + /* + * The driver does not support the IV/EIV generation + * in hardware. However it doesn't support the IV/EIV + * inside the ieee80211 frame either, but requires it + * to be provided seperately for the descriptor. + * rt2x00lib will cut the IV/EIV data out of all frames + * given to us by mac80211, but we must tell mac80211 + * to generate the IV/EIV data. + */ + key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; + key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; + } + + /* + * TXRX_CSR0_KEY_ID contains only single-bit fields to indicate + * a particular key is valid. + */ + rt2500usb_register_read(rt2x00dev, TXRX_CSR0, ®); + rt2x00_set_field16(®, TXRX_CSR0_ALGORITHM, crypto->cipher); + rt2x00_set_field16(®, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER); + + mask = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID); + if (crypto->cmd == SET_KEY) + mask |= 1 << key->hw_key_idx; + else if (crypto->cmd == DISABLE_KEY) + mask &= ~(1 << key->hw_key_idx); + rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, mask); + rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg); + + return 0; +} + static void rt2500usb_config_filter(struct rt2x00_dev *rt2x00dev, const unsigned int filter_flags) { @@ -844,7 +927,7 @@ static int rt2500usb_init_registers(struct rt2x00_dev *rt2x00dev) rt2500usb_register_read(rt2x00dev, TXRX_CSR0, ®); rt2x00_set_field16(®, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER); - rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, 0xff); + rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, 0); rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg); rt2500usb_register_read(rt2x00dev, MAC_CSR18, ®); @@ -1066,7 +1149,7 @@ static void rt2500usb_write_tx_desc(struct rt2x00_dev *rt2x00dev, * Start writing the descriptor words. */ rt2x00_desc_read(txd, 1, &word); - rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, IEEE80211_HEADER); + rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset); rt2x00_set_field32(&word, TXD_W1_AIFS, txdesc->aifs); rt2x00_set_field32(&word, TXD_W1_CWMIN, txdesc->cw_min); rt2x00_set_field32(&word, TXD_W1_CWMAX, txdesc->cw_max); @@ -1079,6 +1162,11 @@ static void rt2500usb_write_tx_desc(struct rt2x00_dev *rt2x00dev, rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH, txdesc->length_high); rt2x00_desc_write(txd, 2, word); + if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) { + _rt2x00_desc_write(txd, 3, skbdesc->iv[0]); + _rt2x00_desc_write(txd, 4, skbdesc->iv[1]); + } + rt2x00_desc_read(txd, 0, &word); rt2x00_set_field32(&word, TXD_W0_RETRY_LIMIT, txdesc->retry_limit); rt2x00_set_field32(&word, TXD_W0_MORE_FRAG, @@ -1093,7 +1181,8 @@ static void rt2500usb_write_tx_desc(struct rt2x00_dev *rt2x00dev, test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags)); rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->ifs); rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, skb->len); - rt2x00_set_field32(&word, TXD_W0_CIPHER, CIPHER_NONE); + rt2x00_set_field32(&word, TXD_W0_CIPHER, txdesc->cipher); + rt2x00_set_field32(&word, TXD_W0_KEY_ID, txdesc->key_idx); rt2x00_desc_write(txd, 0, word); } @@ -1204,6 +1293,7 @@ static void rt2500usb_kick_tx_queue(struct rt2x00_dev *rt2x00dev, static void rt2500usb_fill_rxdone(struct queue_entry *entry, struct rxdone_entry_desc *rxdesc) { + struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; struct queue_entry_priv_usb *entry_priv = entry->priv_data; struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); __le32 *rxd = @@ -1231,6 +1321,31 @@ static void rt2500usb_fill_rxdone(struct queue_entry *entry, if (rt2x00_get_field32(word0, RXD_W0_PHYSICAL_ERROR)) rxdesc->flags |= RX_FLAG_FAILED_PLCP_CRC; + if (test_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags)) { + rxdesc->cipher = rt2x00_get_field32(word0, RXD_W0_CIPHER); + if (rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR)) + rxdesc->cipher_status = RX_CRYPTO_FAIL_KEY; + } + + if (rxdesc->cipher != CIPHER_NONE) { + _rt2x00_desc_read(rxd, 2, &rxdesc->iv[0]); + _rt2x00_desc_read(rxd, 3, &rxdesc->iv[1]); + /* ICV is located at the end of frame */ + + /* + * Hardware has stripped IV/EIV data from 802.11 frame during + * decryption. It has provided the data seperately but rt2x00lib + * should decide if it should be reinserted. + */ + rxdesc->flags |= RX_FLAG_IV_STRIPPED; + if (rxdesc->cipher != CIPHER_TKIP) + rxdesc->flags |= RX_FLAG_MMIC_STRIPPED; + if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS) + rxdesc->flags |= RX_FLAG_DECRYPTED; + else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC) + rxdesc->flags |= RX_FLAG_MMIC_ERROR; + } + /* * Obtain the status about this packet. * When frame was received with an OFDM bitrate, @@ -1238,8 +1353,8 @@ static void rt2500usb_fill_rxdone(struct queue_entry *entry, * a CCK bitrate the signal is the rate in 100kbit/s. */ rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL); - rxdesc->rssi = rt2x00_get_field32(word1, RXD_W1_RSSI) - - entry->queue->rt2x00dev->rssi_offset; + rxdesc->rssi = + rt2x00_get_field32(word1, RXD_W1_RSSI) - rt2x00dev->rssi_offset; rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT); if (rt2x00_get_field32(word0, RXD_W0_OFDM)) @@ -1727,6 +1842,10 @@ static int rt2500usb_probe_hw(struct rt2x00_dev *rt2x00dev) __set_bit(DRIVER_REQUIRE_ATIM_QUEUE, &rt2x00dev->flags); __set_bit(DRIVER_REQUIRE_BEACON_GUARD, &rt2x00dev->flags); __set_bit(DRIVER_REQUIRE_SCHEDULED, &rt2x00dev->flags); + if (!modparam_nohwcrypt) { + __set_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags); + __set_bit(CONFIG_CRYPTO_COPY_IV, &rt2x00dev->flags); + } __set_bit(CONFIG_DISABLE_LINK_TUNING, &rt2x00dev->flags); /* @@ -1746,6 +1865,7 @@ static const struct ieee80211_ops rt2500usb_mac80211_ops = { .config = rt2x00mac_config, .config_interface = rt2x00mac_config_interface, .configure_filter = rt2x00mac_configure_filter, + .set_key = rt2x00mac_set_key, .get_stats = rt2x00mac_get_stats, .bss_info_changed = rt2x00mac_bss_info_changed, .conf_tx = rt2x00mac_conf_tx, @@ -1767,6 +1887,8 @@ static const struct rt2x00lib_ops rt2500usb_rt2x00_ops = { .get_tx_data_len = rt2500usb_get_tx_data_len, .kick_tx_queue = rt2500usb_kick_tx_queue, .fill_rxdone = rt2500usb_fill_rxdone, + .config_shared_key = rt2500usb_config_key, + .config_pairwise_key = rt2500usb_config_key, .config_filter = rt2500usb_config_filter, .config_intf = rt2500usb_config_intf, .config_erp = rt2500usb_config_erp, diff --git a/drivers/net/wireless/rt2x00/rt2500usb.h b/drivers/net/wireless/rt2x00/rt2500usb.h index dbb5d689e23..4347dfdabcd 100644 --- a/drivers/net/wireless/rt2x00/rt2500usb.h +++ b/drivers/net/wireless/rt2x00/rt2500usb.h @@ -447,6 +447,9 @@ #define SEC_CSR30 0x04bc #define SEC_CSR31 0x04be +#define KEY_ENTRY(__idx) \ + ( SEC_CSR0 + ((__idx) * 16) ) + /* * PHY control registers. */ diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h index e7ed56dcf68..03d34bb6618 100644 --- a/drivers/net/wireless/rt2x00/rt2x00.h +++ b/drivers/net/wireless/rt2x00/rt2x00.h @@ -653,6 +653,7 @@ enum rt2x00_flags { CONFIG_EXTERNAL_LNA_BG, CONFIG_DOUBLE_ANTENNA, CONFIG_DISABLE_LINK_TUNING, + CONFIG_CRYPTO_COPY_IV, }; /* diff --git a/drivers/net/wireless/rt2x00/rt2x00crypto.c b/drivers/net/wireless/rt2x00/rt2x00crypto.c index e0fc7c19304..c6709b39216 100644 --- a/drivers/net/wireless/rt2x00/rt2x00crypto.c +++ b/drivers/net/wireless/rt2x00/rt2x00crypto.c @@ -69,6 +69,18 @@ unsigned int rt2x00crypto_tx_overhead(struct ieee80211_tx_info *tx_info) return overhead; } +void rt2x00crypto_tx_copy_iv(struct sk_buff *skb, unsigned int iv_len) +{ + struct skb_frame_desc *skbdesc = get_skb_frame_desc(skb); + unsigned int header_length = ieee80211_get_hdrlen_from_skb(skb); + + if (unlikely(!iv_len)) + return; + + /* Copy IV/EIV data */ + memcpy(skbdesc->iv, skb->data + header_length, iv_len); +} + void rt2x00crypto_tx_remove_iv(struct sk_buff *skb, unsigned int iv_len) { struct skb_frame_desc *skbdesc = get_skb_frame_desc(skb); diff --git a/drivers/net/wireless/rt2x00/rt2x00lib.h b/drivers/net/wireless/rt2x00/rt2x00lib.h index 93997333d46..1e1893772b6 100644 --- a/drivers/net/wireless/rt2x00/rt2x00lib.h +++ b/drivers/net/wireless/rt2x00/rt2x00lib.h @@ -219,6 +219,7 @@ static inline void rt2x00debug_update_crypto(struct rt2x00_dev *rt2x00dev, #ifdef CONFIG_RT2X00_LIB_CRYPTO enum cipher rt2x00crypto_key_to_cipher(struct ieee80211_key_conf *key); unsigned int rt2x00crypto_tx_overhead(struct ieee80211_tx_info *tx_info); +void rt2x00crypto_tx_copy_iv(struct sk_buff *skb, unsigned int iv_len); void rt2x00crypto_tx_remove_iv(struct sk_buff *skb, unsigned int iv_len); void rt2x00crypto_tx_insert_iv(struct sk_buff *skb); void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, unsigned int align, @@ -235,6 +236,11 @@ static inline unsigned int rt2x00crypto_tx_overhead(struct ieee80211_tx_info *tx return 0; } +static inline void rt2x00crypto_tx_copy_iv(struct sk_buff *skb, + unsigned int iv_len) +{ +} + static inline void rt2x00crypto_tx_remove_iv(struct sk_buff *skb, unsigned int iv_len) { diff --git a/drivers/net/wireless/rt2x00/rt2x00mac.c b/drivers/net/wireless/rt2x00/rt2x00mac.c index 4c039572906..fa91ca5cd0e 100644 --- a/drivers/net/wireless/rt2x00/rt2x00mac.c +++ b/drivers/net/wireless/rt2x00/rt2x00mac.c @@ -79,10 +79,8 @@ static int rt2x00mac_tx_rts_cts(struct rt2x00_dev *rt2x00dev, * RTS/CTS frame should use the length of the frame plus any * encryption overhead that will be added by the hardware. */ -#ifdef CONFIG_RT2X00_LIB_CRYPTO if (!frag_skb->do_not_encrypt) data_length += rt2x00crypto_tx_overhead(tx_info); -#endif /* CONFIG_RT2X00_LIB_CRYPTO */ if (tx_info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) ieee80211_ctstoself_get(rt2x00dev->hw, tx_info->control.vif, diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.c b/drivers/net/wireless/rt2x00/rt2x00queue.c index 7f908a17e36..e4a1dbeb18f 100644 --- a/drivers/net/wireless/rt2x00/rt2x00queue.c +++ b/drivers/net/wireless/rt2x00/rt2x00queue.c @@ -420,8 +420,12 @@ int rt2x00queue_write_tx_frame(struct data_queue *queue, struct sk_buff *skb) * the frame so we can provide it to the driver seperately. */ if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc.flags) && - !test_bit(ENTRY_TXD_ENCRYPT_IV, &txdesc.flags)) - rt2x00crypto_tx_remove_iv(skb, iv_len); + !test_bit(ENTRY_TXD_ENCRYPT_IV, &txdesc.flags)) { + if (test_bit(CONFIG_CRYPTO_COPY_IV, &queue->rt2x00dev->flags)) + rt2x00crypto_tx_copy_iv(skb, iv_len); + else + rt2x00crypto_tx_remove_iv(skb, iv_len); + } /* * It could be possible that the queue was corrupted and this