From: NeilBrown Date: Mon, 27 Mar 2006 09:18:09 +0000 (-0800) Subject: [PATCH] md: Core of raid5 resize process X-Git-Tag: v2.6.17-rc1~290 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=ccfcc3c10b2a5cb8fd3c918199a4ff904fc6fb3e;p=linux-2.6-omap-h63xx.git [PATCH] md: Core of raid5 resize process This patch provides the core of the resize/expand process. sync_request notices if a 'reshape' is happening and acts accordingly. It allocated new stripe_heads for the next chunk-wide-stripe in the target geometry, marking them STRIPE_EXPANDING. Then it finds which stripe heads in the old geometry can provide data needed by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to read all blocks on those stripes. Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then is written out and released. Signed-off-by: Neil Brown Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- diff --git a/drivers/md/md.c b/drivers/md/md.c index c7b7656f9aa..8e65986bc63 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -2165,7 +2165,9 @@ action_show(mddev_t *mddev, char *page) char *type = "idle"; if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery) || test_bit(MD_RECOVERY_NEEDED, &mddev->recovery)) { - if (test_bit(MD_RECOVERY_SYNC, &mddev->recovery)) { + if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery)) + type = "reshape"; + else if (test_bit(MD_RECOVERY_SYNC, &mddev->recovery)) { if (!test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery)) type = "resync"; else if (test_bit(MD_RECOVERY_CHECK, &mddev->recovery)) @@ -4088,8 +4090,10 @@ static void status_resync(struct seq_file *seq, mddev_t * mddev) seq_printf(seq, "] "); } seq_printf(seq, " %s =%3u.%u%% (%llu/%llu)", + (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery)? + "reshape" : (test_bit(MD_RECOVERY_SYNC, &mddev->recovery) ? - "resync" : "recovery"), + "resync" : "recovery")), per_milli/10, per_milli % 10, (unsigned long long) resync, (unsigned long long) max_blocks); @@ -4543,7 +4547,9 @@ static void md_do_sync(mddev_t *mddev) */ max_sectors = mddev->resync_max_sectors; mddev->resync_mismatches = 0; - } else + } else if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery)) + max_sectors = mddev->size << 1; + else /* recovery follows the physical size of devices */ max_sectors = mddev->size << 1; @@ -4679,6 +4685,8 @@ static void md_do_sync(mddev_t *mddev) mddev->pers->sync_request(mddev, max_sectors, &skipped, 1); if (!test_bit(MD_RECOVERY_ERR, &mddev->recovery) && + test_bit(MD_RECOVERY_SYNC, &mddev->recovery) && + !test_bit(MD_RECOVERY_CHECK, &mddev->recovery) && mddev->curr_resync > 2 && mddev->curr_resync >= mddev->recovery_cp) { if (test_bit(MD_RECOVERY_INTR, &mddev->recovery)) { diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 7a6df515b00..56cba8d3e39 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -93,11 +93,11 @@ static void __release_stripe(raid5_conf_t *conf, struct stripe_head *sh) if (atomic_read(&conf->preread_active_stripes) < IO_THRESHOLD) md_wakeup_thread(conf->mddev->thread); } - list_add_tail(&sh->lru, &conf->inactive_list); atomic_dec(&conf->active_stripes); - if (!conf->inactive_blocked || - atomic_read(&conf->active_stripes) < (conf->max_nr_stripes*3/4)) + if (!test_bit(STRIPE_EXPANDING, &sh->state)) { + list_add_tail(&sh->lru, &conf->inactive_list); wake_up(&conf->wait_for_stripe); + } } } } @@ -273,9 +273,8 @@ static struct stripe_head *get_active_stripe(raid5_conf_t *conf, sector_t sector } else { if (!test_bit(STRIPE_HANDLE, &sh->state)) atomic_inc(&conf->active_stripes); - if (list_empty(&sh->lru)) - BUG(); - list_del_init(&sh->lru); + if (!list_empty(&sh->lru)) + list_del_init(&sh->lru); } } } while (sh == NULL); @@ -1035,6 +1034,18 @@ static int add_stripe_bio(struct stripe_head *sh, struct bio *bi, int dd_idx, in return 0; } +static int stripe_to_pdidx(sector_t stripe, raid5_conf_t *conf, int disks) +{ + int sectors_per_chunk = conf->chunk_size >> 9; + sector_t x = stripe; + int pd_idx, dd_idx; + int chunk_offset = sector_div(x, sectors_per_chunk); + stripe = x; + raid5_compute_sector(stripe*(disks-1)*sectors_per_chunk + + chunk_offset, disks, disks-1, &dd_idx, &pd_idx, conf); + return pd_idx; +} + /* * handle_stripe - do things to a stripe. @@ -1061,7 +1072,7 @@ static void handle_stripe(struct stripe_head *sh) struct bio *return_bi= NULL; struct bio *bi; int i; - int syncing; + int syncing, expanding, expanded; int locked=0, uptodate=0, to_read=0, to_write=0, failed=0, written=0; int non_overwrite = 0; int failed_num=0; @@ -1076,6 +1087,8 @@ static void handle_stripe(struct stripe_head *sh) clear_bit(STRIPE_DELAYED, &sh->state); syncing = test_bit(STRIPE_SYNCING, &sh->state); + expanding = test_bit(STRIPE_EXPAND_SOURCE, &sh->state); + expanded = test_bit(STRIPE_EXPAND_READY, &sh->state); /* Now to look around and see what can be done */ rcu_read_lock(); @@ -1268,13 +1281,14 @@ static void handle_stripe(struct stripe_head *sh) * parity, or to satisfy requests * or to load a block that is being partially written. */ - if (to_read || non_overwrite || (syncing && (uptodate < disks))) { + if (to_read || non_overwrite || (syncing && (uptodate < disks)) || expanding) { for (i=disks; i--;) { dev = &sh->dev[i]; if (!test_bit(R5_LOCKED, &dev->flags) && !test_bit(R5_UPTODATE, &dev->flags) && (dev->toread || (dev->towrite && !test_bit(R5_OVERWRITE, &dev->flags)) || syncing || + expanding || (failed && (sh->dev[failed_num].toread || (sh->dev[failed_num].towrite && !test_bit(R5_OVERWRITE, &sh->dev[failed_num].flags)))) ) @@ -1464,13 +1478,76 @@ static void handle_stripe(struct stripe_head *sh) set_bit(R5_Wantwrite, &dev->flags); set_bit(R5_ReWrite, &dev->flags); set_bit(R5_LOCKED, &dev->flags); + locked++; } else { /* let's read it back */ set_bit(R5_Wantread, &dev->flags); set_bit(R5_LOCKED, &dev->flags); + locked++; } } + if (expanded && test_bit(STRIPE_EXPANDING, &sh->state)) { + /* Need to write out all blocks after computing parity */ + sh->disks = conf->raid_disks; + sh->pd_idx = stripe_to_pdidx(sh->sector, conf, conf->raid_disks); + compute_parity(sh, RECONSTRUCT_WRITE); + for (i= conf->raid_disks; i--;) { + set_bit(R5_LOCKED, &sh->dev[i].flags); + locked++; + set_bit(R5_Wantwrite, &sh->dev[i].flags); + } + clear_bit(STRIPE_EXPANDING, &sh->state); + } else if (expanded) { + clear_bit(STRIPE_EXPAND_READY, &sh->state); + wake_up(&conf->wait_for_overlap); + md_done_sync(conf->mddev, STRIPE_SECTORS, 1); + } + + if (expanding && locked == 0) { + /* We have read all the blocks in this stripe and now we need to + * copy some of them into a target stripe for expand. + */ + clear_bit(STRIPE_EXPAND_SOURCE, &sh->state); + for (i=0; i< sh->disks; i++) + if (i != sh->pd_idx) { + int dd_idx, pd_idx, j; + struct stripe_head *sh2; + + sector_t bn = compute_blocknr(sh, i); + sector_t s = raid5_compute_sector(bn, conf->raid_disks, + conf->raid_disks-1, + &dd_idx, &pd_idx, conf); + sh2 = get_active_stripe(conf, s, conf->raid_disks, pd_idx, 1); + if (sh2 == NULL) + /* so far only the early blocks of this stripe + * have been requested. When later blocks + * get requested, we will try again + */ + continue; + if(!test_bit(STRIPE_EXPANDING, &sh2->state) || + test_bit(R5_Expanded, &sh2->dev[dd_idx].flags)) { + /* must have already done this block */ + release_stripe(sh2); + continue; + } + memcpy(page_address(sh2->dev[dd_idx].page), + page_address(sh->dev[i].page), + STRIPE_SIZE); + set_bit(R5_Expanded, &sh2->dev[dd_idx].flags); + set_bit(R5_UPTODATE, &sh2->dev[dd_idx].flags); + for (j=0; jraid_disks; j++) + if (j != sh2->pd_idx && + !test_bit(R5_Expanded, &sh2->dev[j].flags)) + break; + if (j == conf->raid_disks) { + set_bit(STRIPE_EXPAND_READY, &sh2->state); + set_bit(STRIPE_HANDLE, &sh2->state); + } + release_stripe(sh2); + } + } + spin_unlock(&sh->lock); while ((bi=return_bi)) { @@ -1509,7 +1586,7 @@ static void handle_stripe(struct stripe_head *sh) rcu_read_unlock(); if (rdev) { - if (syncing) + if (syncing || expanding || expanded) md_sync_acct(rdev->bdev, STRIPE_SECTORS); bi->bi_bdev = rdev->bdev; @@ -1757,12 +1834,8 @@ static sector_t sync_request(mddev_t *mddev, sector_t sector_nr, int *skipped, i { raid5_conf_t *conf = (raid5_conf_t *) mddev->private; struct stripe_head *sh; - int sectors_per_chunk = conf->chunk_size >> 9; - sector_t x; - unsigned long stripe; - int chunk_offset; - int dd_idx, pd_idx; - sector_t first_sector; + int pd_idx; + sector_t first_sector, last_sector; int raid_disks = conf->raid_disks; int data_disks = raid_disks-1; sector_t max_sector = mddev->size << 1; @@ -1781,6 +1854,80 @@ static sector_t sync_request(mddev_t *mddev, sector_t sector_nr, int *skipped, i return 0; } + + if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery)) { + /* reshaping is quite different to recovery/resync so it is + * handled quite separately ... here. + * + * On each call to sync_request, we gather one chunk worth of + * destination stripes and flag them as expanding. + * Then we find all the source stripes and request reads. + * As the reads complete, handle_stripe will copy the data + * into the destination stripe and release that stripe. + */ + int i; + int dd_idx; + for (i=0; i < conf->chunk_size/512; i+= STRIPE_SECTORS) { + int j; + int skipped = 0; + pd_idx = stripe_to_pdidx(sector_nr+i, conf, conf->raid_disks); + sh = get_active_stripe(conf, sector_nr+i, + conf->raid_disks, pd_idx, 0); + set_bit(STRIPE_EXPANDING, &sh->state); + /* If any of this stripe is beyond the end of the old + * array, then we need to zero those blocks + */ + for (j=sh->disks; j--;) { + sector_t s; + if (j == sh->pd_idx) + continue; + s = compute_blocknr(sh, j); + if (s < (mddev->array_size<<1)) { + skipped = 1; + continue; + } + memset(page_address(sh->dev[j].page), 0, STRIPE_SIZE); + set_bit(R5_Expanded, &sh->dev[j].flags); + set_bit(R5_UPTODATE, &sh->dev[j].flags); + } + if (!skipped) { + set_bit(STRIPE_EXPAND_READY, &sh->state); + set_bit(STRIPE_HANDLE, &sh->state); + } + release_stripe(sh); + } + spin_lock_irq(&conf->device_lock); + conf->expand_progress = (sector_nr + i)*(conf->raid_disks-1); + spin_unlock_irq(&conf->device_lock); + /* Ok, those stripe are ready. We can start scheduling + * reads on the source stripes. + * The source stripes are determined by mapping the first and last + * block on the destination stripes. + */ + raid_disks = conf->previous_raid_disks; + data_disks = raid_disks - 1; + first_sector = + raid5_compute_sector(sector_nr*(conf->raid_disks-1), + raid_disks, data_disks, + &dd_idx, &pd_idx, conf); + last_sector = + raid5_compute_sector((sector_nr+conf->chunk_size/512) + *(conf->raid_disks-1) -1, + raid_disks, data_disks, + &dd_idx, &pd_idx, conf); + if (last_sector >= (mddev->size<<1)) + last_sector = (mddev->size<<1)-1; + while (first_sector <= last_sector) { + pd_idx = stripe_to_pdidx(first_sector, conf, conf->previous_raid_disks); + sh = get_active_stripe(conf, first_sector, + conf->previous_raid_disks, pd_idx, 0); + set_bit(STRIPE_EXPAND_SOURCE, &sh->state); + set_bit(STRIPE_HANDLE, &sh->state); + release_stripe(sh); + first_sector += STRIPE_SECTORS; + } + return conf->chunk_size>>9; + } /* if there is 1 or more failed drives and we are trying * to resync, then assert that we are finished, because there is * nothing we can do. @@ -1799,13 +1946,7 @@ static sector_t sync_request(mddev_t *mddev, sector_t sector_nr, int *skipped, i return sync_blocks * STRIPE_SECTORS; /* keep things rounded to whole stripes */ } - x = sector_nr; - chunk_offset = sector_div(x, sectors_per_chunk); - stripe = x; - BUG_ON(x != stripe); - - first_sector = raid5_compute_sector((sector_t)stripe*data_disks*sectors_per_chunk - + chunk_offset, raid_disks, data_disks, &dd_idx, &pd_idx, conf); + pd_idx = stripe_to_pdidx(sector_nr, conf, raid_disks); sh = get_active_stripe(conf, sector_nr, raid_disks, pd_idx, 1); if (sh == NULL) { sh = get_active_stripe(conf, sector_nr, raid_disks, pd_idx, 0); diff --git a/include/linux/raid/md_k.h b/include/linux/raid/md_k.h index 617b9506c76..4e26ef2cacc 100644 --- a/include/linux/raid/md_k.h +++ b/include/linux/raid/md_k.h @@ -157,6 +157,9 @@ struct mddev_s * DONE: thread is done and is waiting to be reaped * REQUEST: user-space has requested a sync (used with SYNC) * CHECK: user-space request for for check-only, no repair + * RESHAPE: A reshape is happening + * + * If neither SYNC or RESHAPE are set, then it is a recovery. */ #define MD_RECOVERY_RUNNING 0 #define MD_RECOVERY_SYNC 1 @@ -166,6 +169,7 @@ struct mddev_s #define MD_RECOVERY_NEEDED 5 #define MD_RECOVERY_REQUESTED 6 #define MD_RECOVERY_CHECK 7 +#define MD_RECOVERY_RESHAPE 8 unsigned long recovery; int in_sync; /* know to not need resync */ diff --git a/include/linux/raid/raid5.h b/include/linux/raid/raid5.h index 6fa274aea2a..55c738d5050 100644 --- a/include/linux/raid/raid5.h +++ b/include/linux/raid/raid5.h @@ -157,6 +157,7 @@ struct stripe_head { #define R5_ReadError 8 /* seen a read error here recently */ #define R5_ReWrite 9 /* have tried to over-write the readerror */ +#define R5_Expanded 10 /* This block now has post-expand data */ /* * Write method */ @@ -176,7 +177,8 @@ struct stripe_head { #define STRIPE_DEGRADED 7 #define STRIPE_BIT_DELAY 8 #define STRIPE_EXPANDING 9 - +#define STRIPE_EXPAND_SOURCE 10 +#define STRIPE_EXPAND_READY 11 /* * Plugging: *