From: Mark Brown Date: Wed, 31 Dec 2008 12:52:42 +0000 (+0000) Subject: regulator: Add missing kerneldoc X-Git-Tag: v2.6.29-rc1~44^2~4 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=c8e7e4640facbe99d10a6e262523b25be129b9b9;p=linux-2.6-omap-h63xx.git regulator: Add missing kerneldoc This is only the documentation that the kerneldoc system warns about. Signed-off-by: Mark Brown Signed-off-by: Liam Girdwood --- diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index ea12c68c327..fda44009024 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -656,6 +656,7 @@ static void print_constraints(struct regulator_dev *rdev) /** * set_machine_constraints - sets regulator constraints * @rdev: regulator source + * @constraints: constraints to apply * * Allows platform initialisation code to define and constrain * regulator circuits e.g. valid voltage/current ranges, etc. NOTE: diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index e37d8056198..84c3737c2d2 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -24,7 +24,37 @@ struct regulator_init_data; /** * struct regulator_ops - regulator operations. * - * This struct describes regulator operations. + * This struct describes regulator operations which can be implemented by + * regulator chip drivers. + * + * @enable: Enable the regulator. + * @disable: Disable the regulator. + * @is_enabled: Return 1 if the reguator is enabled, 0 otherwise. + * + * @set_voltage: Set the voltage for the regulator within the range specified. + * The driver should select the voltage closest to min_uV. + * @get_voltage: Return the currently configured voltage for the regulator. + * + * @set_current: Set the current for the regulator within the range specified. + * The driver should select the current closest to min_uA. + * @get_current: Return the currently configured current for the regulator. + * + * @set_current_limit: Configure a limit for a current-limited regulator. + * @get_current_limit: Get the limit for a current-limited regulator. + * + * @set_mode: Set the operating mode for the regulator. + * @get_mode: Get the current operating mode for the regulator. + * @get_optimum_mode: Get the most efficient operating mode for the regulator + * when running with the specified parameters. + * + * @set_suspend_voltage: Set the voltage for the regulator when the system + * is suspended. + * @set_suspend_enable: Mark the regulator as enabled when the system is + * suspended. + * @set_suspend_disable: Mark the regulator as disabled when the system is + * suspended. + * @set_suspend_mode: Set the operating mode for the regulator when the + * system is suspended. */ struct regulator_ops { @@ -75,6 +105,14 @@ enum regulator_type { /** * struct regulator_desc - Regulator descriptor * + * Each regulator registered with the core is described with a structure of + * this type. + * + * @name: Identifying name for the regulator. + * @id: Numerical identifier for the regulator. + * @ops: Regulator operations table. + * @type: Indicates if the regulator is a voltage or current regulator. + * @owner: Module providing the regulator, used for refcounting. */ struct regulator_desc { const char *name; diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index c6d69331a81..3794773b23d 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -44,6 +44,10 @@ struct regulator; * struct regulator_state - regulator state during low power syatem states * * This describes a regulators state during a system wide low power state. + * + * @uV: Operating voltage during suspend. + * @mode: Operating mode during suspend. + * @enabled: Enabled during suspend. */ struct regulator_state { int uV; /* suspend voltage */ @@ -55,6 +59,30 @@ struct regulator_state { * struct regulation_constraints - regulator operating constraints. * * This struct describes regulator and board/machine specific constraints. + * + * @name: Descriptive name for the constraints, used for display purposes. + * + * @min_uV: Smallest voltage consumers may set. + * @max_uV: Largest voltage consumers may set. + * + * @min_uA: Smallest consumers consumers may set. + * @max_uA: Largest current consumers may set. + * + * @valid_modes_mask: Mask of modes which may be configured by consumers. + * @valid_ops_mask: Operations which may be performed by consumers. + * + * @always_on: Set if the regulator should never be disabled. + * @boot_on: Set if the regulator is enabled when the system is initially + * started. + * @apply_uV: Apply the voltage constraint when initialising. + * + * @input_uV: Input voltage for regulator when supplied by another regulator. + * + * @state_disk: State for regulator when system is suspended in disk mode. + * @state_mem: State for regulator when system is suspended in mem mode. + * @state_standby: State for regulator when system is suspended in standby + * mode. + * @initial_state: Suspend state to set by default. */ struct regulation_constraints { @@ -93,6 +121,9 @@ struct regulation_constraints { * struct regulator_consumer_supply - supply -> device mapping * * This maps a supply name to a device. + * + * @dev: Device structure for the consumer. + * @supply: Name for the supply. */ struct regulator_consumer_supply { struct device *dev; /* consumer */ @@ -103,6 +134,16 @@ struct regulator_consumer_supply { * struct regulator_init_data - regulator platform initialisation data. * * Initialisation constraints, our supply and consumers supplies. + * + * @supply_regulator_dev: Parent regulator (if any). + * + * @constraints: Constraints. These must be specified for the regulator to + * be usable. + * @num_consumer_supplies: Number of consumer device supplies. + * @consumer_supplies: Consumer device supply configuration. + * + * @regulator_init: Callback invoked when the regulator has been registered. + * @driver_data: Data passed to regulator_init. */ struct regulator_init_data { struct device *supply_regulator_dev; /* or NULL for LINE */