From: Oliver McFadden Date: Wed, 11 Jul 2007 02:24:10 +0000 (+1000) Subject: r300: updates register header X-Git-Tag: v2.6.23-rc1~774^2~11 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=c6c656b4b6ddfc964f1a43394bf86bc76c5e8119;p=linux-2.6-omap-h63xx.git r300: updates register header This updates the R300 register names and allows the VAP_PVS_WAITIDLE register to be written. Signed-off-by: Dave Airlie --- diff --git a/drivers/char/drm/r300_cmdbuf.c b/drivers/char/drm/r300_cmdbuf.c index 032a022ec6a..28fbf3dda28 100644 --- a/drivers/char/drm/r300_cmdbuf.c +++ b/drivers/char/drm/r300_cmdbuf.c @@ -148,15 +148,16 @@ void r300_init_reg_flags(void) /* these match cmducs() command in r300_driver/r300/r300_cmdbuf.c */ ADD_RANGE(R300_SE_VPORT_XSCALE, 6); - ADD_RANGE(0x2080, 1); + ADD_RANGE(R300_VAP_CNTL, 1); ADD_RANGE(R300_SE_VTE_CNTL, 2); ADD_RANGE(0x2134, 2); - ADD_RANGE(0x2140, 1); + ADD_RANGE(R300_VAP_CNTL_STATUS, 1); ADD_RANGE(R300_VAP_INPUT_CNTL_0, 2); ADD_RANGE(0x21DC, 1); - ADD_RANGE(0x221C, 1); - ADD_RANGE(0x2220, 4); - ADD_RANGE(0x2288, 1); + ADD_RANGE(R300_VAP_UNKNOWN_221C, 1); + ADD_RANGE(R300_VAP_CLIP_X_0, 4); + ADD_RANGE(R300_VAP_PVS_WAITIDLE, 1); + ADD_RANGE(R300_VAP_UNKNOWN_2288, 1); ADD_RANGE(R300_VAP_OUTPUT_VTX_FMT_0, 2); ADD_RANGE(R300_VAP_PVS_CNTL_1, 3); ADD_RANGE(R300_GB_ENABLE, 1); @@ -168,13 +169,13 @@ void r300_init_reg_flags(void) ADD_RANGE(R300_RE_POINTSIZE, 1); ADD_RANGE(0x4230, 3); ADD_RANGE(R300_RE_LINE_CNT, 1); - ADD_RANGE(0x4238, 1); + ADD_RANGE(R300_RE_UNK4238, 1); ADD_RANGE(0x4260, 3); - ADD_RANGE(0x4274, 4); - ADD_RANGE(0x4288, 5); - ADD_RANGE(0x42A0, 1); + ADD_RANGE(R300_RE_SHADE, 4); + ADD_RANGE(R300_RE_POLYGON_MODE, 5); + ADD_RANGE(R300_RE_ZBIAS_CNTL, 1); ADD_RANGE(R300_RE_ZBIAS_T_FACTOR, 4); - ADD_RANGE(0x42B4, 1); + ADD_RANGE(R300_RE_OCCLUSION_CNTL, 1); ADD_RANGE(R300_RE_CULL_CNTL, 1); ADD_RANGE(0x42C0, 2); ADD_RANGE(R300_RS_CNTL_0, 2); @@ -190,22 +191,22 @@ void r300_init_reg_flags(void) ADD_RANGE(R300_PFS_INSTR1_0, 64); ADD_RANGE(R300_PFS_INSTR2_0, 64); ADD_RANGE(R300_PFS_INSTR3_0, 64); - ADD_RANGE(0x4BC0, 1); - ADD_RANGE(0x4BC8, 3); + ADD_RANGE(R300_RE_FOG_STATE, 1); + ADD_RANGE(R300_FOG_COLOR_R, 3); ADD_RANGE(R300_PP_ALPHA_TEST, 2); ADD_RANGE(0x4BD8, 1); ADD_RANGE(R300_PFS_PARAM_0_X, 64); ADD_RANGE(0x4E00, 1); ADD_RANGE(R300_RB3D_CBLEND, 2); ADD_RANGE(R300_RB3D_COLORMASK, 1); - ADD_RANGE(0x4E10, 3); + ADD_RANGE(R300_RB3D_BLEND_COLOR, 3); ADD_RANGE_MARK(R300_RB3D_COLOROFFSET0, 1, MARK_CHECK_OFFSET); /* check offset */ ADD_RANGE(R300_RB3D_COLORPITCH0, 1); ADD_RANGE(0x4E50, 9); ADD_RANGE(0x4E88, 1); ADD_RANGE(0x4EA0, 2); ADD_RANGE(R300_RB3D_ZSTENCIL_CNTL_0, 3); - ADD_RANGE(0x4F10, 4); + ADD_RANGE(R300_RB3D_ZSTENCIL_FORMAT, 4); ADD_RANGE_MARK(R300_RB3D_DEPTHOFFSET, 1, MARK_CHECK_OFFSET); /* check offset */ ADD_RANGE(R300_RB3D_DEPTHPITCH, 1); ADD_RANGE(0x4F28, 1); @@ -224,7 +225,7 @@ void r300_init_reg_flags(void) ADD_RANGE(R300_TX_BORDER_COLOR_0, 16); /* Sporadic registers used as primitives are emitted */ - ADD_RANGE(0x4f18, 1); + ADD_RANGE(R300_RB3D_ZCACHE_CTLSTAT, 1); ADD_RANGE(R300_RB3D_DSTCACHE_CTLSTAT, 1); ADD_RANGE(R300_VAP_INPUT_ROUTE_0_0, 8); ADD_RANGE(R300_VAP_INPUT_ROUTE_1_0, 8); @@ -692,9 +693,9 @@ static __inline__ void r300_pacify(drm_radeon_private_t *dev_priv) BEGIN_RING(6); OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); - OUT_RING(0xa); - OUT_RING(CP_PACKET0(0x4f18, 0)); - OUT_RING(0x3); + OUT_RING(R300_RB3D_DSTCACHE_UNKNOWN_0A); + OUT_RING(CP_PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0)); + OUT_RING(R300_RB3D_ZCACHE_UNKNOWN_03); OUT_RING(CP_PACKET3(RADEON_CP_NOP, 0)); OUT_RING(0x0); ADVANCE_RING(); @@ -766,8 +767,8 @@ static int r300_scratch(drm_radeon_private_t *dev_priv, } BEGIN_RING(2); - OUT_RING(CP_PACKET0(RADEON_SCRATCH_REG0 + header.scratch.reg * 4, 0)); - OUT_RING(dev_priv->scratch_ages[header.scratch.reg]); + OUT_RING( CP_PACKET0( RADEON_SCRATCH_REG0 + header.scratch.reg * 4, 0 ) ); + OUT_RING( dev_priv->scratch_ages[header.scratch.reg] ); ADVANCE_RING(); return 0; diff --git a/drivers/char/drm/r300_reg.h b/drivers/char/drm/r300_reg.h index ecda760ae8c..3ae57ecc7af 100644 --- a/drivers/char/drm/r300_reg.h +++ b/drivers/char/drm/r300_reg.h @@ -47,12 +47,12 @@ USE OR OTHER DEALINGS IN THE SOFTWARE. # define R300_MC_MISC__MC_GLOBW_FULL_LAT_SHIFT 28 /* -This file contains registers and constants for the R300. They have been -found mostly by examining command buffers captured using glxtest, as well -as by extrapolating some known registers and constants from the R200. - -I am fairly certain that they are correct unless stated otherwise in comments. -*/ + * This file contains registers and constants for the R300. They have been + * found mostly by examining command buffers captured using glxtest, as well + * as by extrapolating some known registers and constants from the R200. + * I am fairly certain that they are correct unless stated otherwise + * in comments. + */ #define R300_SE_VPORT_XSCALE 0x1D98 #define R300_SE_VPORT_XOFFSET 0x1D9C @@ -61,49 +61,60 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_SE_VPORT_ZSCALE 0x1DA8 #define R300_SE_VPORT_ZOFFSET 0x1DAC -/* This register is written directly and also starts data section in many 3d CP_PACKET3's */ -#define R300_VAP_VF_CNTL 0x2084 -# define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0 -# define R300_VAP_VF_CNTL__PRIM_NONE (0<<0) -# define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0) -# define R300_VAP_VF_CNTL__PRIM_LINES (2<<0) -# define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0) -# define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0) -# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0) -# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0) -# define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0) -# define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0) -# define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0) -# define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0) - -# define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4 - /* State based - direct writes to registers trigger vertex generation */ -# define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4) -# define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4) -# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4) -# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4) - - /* I don't think I saw these three used.. */ -# define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6 -# define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9 -# define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10 - - /* index size - when not set the indices are assumed to be 16 bit */ -# define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11) - /* number of vertices */ -# define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16 +/* + * Vertex Array Processing (VAP) Control + * Stolen from r200 code from Christoph Brill (It's a guess!) + */ +#define R300_VAP_CNTL 0x2080 + +/* This register is written directly and also starts data section + * in many 3d CP_PACKET3's + */ +#define R300_VAP_VF_CNTL 0x2084 +# define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0 +# define R300_VAP_VF_CNTL__PRIM_NONE (0<<0) +# define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0) +# define R300_VAP_VF_CNTL__PRIM_LINES (2<<0) +# define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0) +# define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0) +# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0) +# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0) +# define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0) +# define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0) +# define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0) +# define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0) + +# define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4 + /* State based - direct writes to registers trigger vertex + generation */ +# define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4) +# define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4) +# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4) +# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4) + + /* I don't think I saw these three used.. */ +# define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6 +# define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9 +# define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10 + + /* index size - when not set the indices are assumed to be 16 bit */ +# define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11) + /* number of vertices */ +# define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16 /* BEGIN: Wild guesses */ #define R300_VAP_OUTPUT_VTX_FMT_0 0x2090 # define R300_VAP_OUTPUT_VTX_FMT_0__POS_PRESENT (1<<0) # define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_PRESENT (1<<1) -# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */ -# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */ -# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */ -# define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */ #define R300_VAP_OUTPUT_VTX_FMT_1 0x2094 + /* each of the following is 3 bits wide, specifies number + of components */ # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6 @@ -112,7 +123,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21 -/* END */ +/* END: Wild guesses */ #define R300_SE_VTE_CNTL 0x20b0 # define R300_VPORT_X_SCALE_ENA 0x00000001 @@ -128,43 +139,54 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_VTX_ST_DENORMALIZED 0x00001000 /* BEGIN: Vertex data assembly - lots of uncertainties */ + +/* gap */ + +#define R300_VAP_CNTL_STATUS 0x2140 +# define R300_VC_NO_SWAP (0 << 0) +# define R300_VC_16BIT_SWAP (1 << 0) +# define R300_VC_32BIT_SWAP (2 << 0) +# define R300_VAP_TCL_BYPASS (1 << 8) + /* gap */ + /* Where do we get our vertex data? -// -// Vertex data either comes either from immediate mode registers or from -// vertex arrays. -// There appears to be no mixed mode (though we can force the pitch of -// vertex arrays to 0, effectively reusing the same element over and over -// again). -// -// Immediate mode is controlled by the INPUT_CNTL registers. I am not sure -// if these registers influence vertex array processing. -// -// Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3. -// -// In both cases, vertex attributes are then passed through INPUT_ROUTE. - -// Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data -// into the vertex processor's input registers. -// The first word routes the first input, the second word the second, etc. -// The corresponding input is routed into the register with the given index. -// The list is ended by a word with INPUT_ROUTE_END set. -// -// Always set COMPONENTS_4 in immediate mode. */ + * + * Vertex data either comes either from immediate mode registers or from + * vertex arrays. + * There appears to be no mixed mode (though we can force the pitch of + * vertex arrays to 0, effectively reusing the same element over and over + * again). + * + * Immediate mode is controlled by the INPUT_CNTL registers. I am not sure + * if these registers influence vertex array processing. + * + * Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3. + * + * In both cases, vertex attributes are then passed through INPUT_ROUTE. + * + * Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data + * into the vertex processor's input registers. + * The first word routes the first input, the second word the second, etc. + * The corresponding input is routed into the register with the given index. + * The list is ended by a word with INPUT_ROUTE_END set. + * + * Always set COMPONENTS_4 in immediate mode. + */ #define R300_VAP_INPUT_ROUTE_0_0 0x2150 # define R300_INPUT_ROUTE_COMPONENTS_1 (0 << 0) # define R300_INPUT_ROUTE_COMPONENTS_2 (1 << 0) # define R300_INPUT_ROUTE_COMPONENTS_3 (2 << 0) # define R300_INPUT_ROUTE_COMPONENTS_4 (3 << 0) -# define R300_INPUT_ROUTE_COMPONENTS_RGBA (4 << 0) /* GUESS */ +# define R300_INPUT_ROUTE_COMPONENTS_RGBA (4 << 0) /* GUESS */ # define R300_VAP_INPUT_ROUTE_IDX_SHIFT 8 -# define R300_VAP_INPUT_ROUTE_IDX_MASK (31 << 8) /* GUESS */ +# define R300_VAP_INPUT_ROUTE_IDX_MASK (31 << 8) /* GUESS */ # define R300_VAP_INPUT_ROUTE_END (1 << 13) -# define R300_INPUT_ROUTE_IMMEDIATE_MODE (0 << 14) /* GUESS */ -# define R300_INPUT_ROUTE_FLOAT (1 << 14) /* GUESS */ -# define R300_INPUT_ROUTE_UNSIGNED_BYTE (2 << 14) /* GUESS */ -# define R300_INPUT_ROUTE_FLOAT_COLOR (3 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_IMMEDIATE_MODE (0 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_FLOAT (1 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_UNSIGNED_BYTE (2 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_FLOAT_COLOR (3 << 14) /* GUESS */ #define R300_VAP_INPUT_ROUTE_0_1 0x2154 #define R300_VAP_INPUT_ROUTE_0_2 0x2158 #define R300_VAP_INPUT_ROUTE_0_3 0x215C @@ -174,10 +196,12 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_VAP_INPUT_ROUTE_0_7 0x216C /* gap */ + /* Notes: -// - always set up to produce at least two attributes: -// if vertex program uses only position, fglrx will set normal, too -// - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal */ + * - always set up to produce at least two attributes: + * if vertex program uses only position, fglrx will set normal, too + * - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal. + */ #define R300_VAP_INPUT_CNTL_0 0x2180 # define R300_INPUT_CNTL_0_COLOR 0x00000001 #define R300_VAP_INPUT_CNTL_1 0x2184 @@ -186,20 +210,22 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_INPUT_CNTL_COLOR 0x00000004 # define R300_INPUT_CNTL_TC0 0x00000400 # define R300_INPUT_CNTL_TC1 0x00000800 -# define R300_INPUT_CNTL_TC2 0x00001000 /* GUESS */ -# define R300_INPUT_CNTL_TC3 0x00002000 /* GUESS */ -# define R300_INPUT_CNTL_TC4 0x00004000 /* GUESS */ -# define R300_INPUT_CNTL_TC5 0x00008000 /* GUESS */ -# define R300_INPUT_CNTL_TC6 0x00010000 /* GUESS */ -# define R300_INPUT_CNTL_TC7 0x00020000 /* GUESS */ +# define R300_INPUT_CNTL_TC2 0x00001000 /* GUESS */ +# define R300_INPUT_CNTL_TC3 0x00002000 /* GUESS */ +# define R300_INPUT_CNTL_TC4 0x00004000 /* GUESS */ +# define R300_INPUT_CNTL_TC5 0x00008000 /* GUESS */ +# define R300_INPUT_CNTL_TC6 0x00010000 /* GUESS */ +# define R300_INPUT_CNTL_TC7 0x00020000 /* GUESS */ /* gap */ + /* Words parallel to INPUT_ROUTE_0; All words that are active in INPUT_ROUTE_0 -// are set to a swizzling bit pattern, other words are 0. -// -// In immediate mode, the pattern is always set to xyzw. In vertex array -// mode, the swizzling pattern is e.g. used to set zw components in texture -// coordinates with only tweo components. */ + * are set to a swizzling bit pattern, other words are 0. + * + * In immediate mode, the pattern is always set to xyzw. In vertex array + * mode, the swizzling pattern is e.g. used to set zw components in texture + * coordinates with only tweo components. + */ #define R300_VAP_INPUT_ROUTE_1_0 0x21E0 # define R300_INPUT_ROUTE_SELECT_X 0 # define R300_INPUT_ROUTE_SELECT_Y 1 @@ -208,11 +234,11 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_INPUT_ROUTE_SELECT_ZERO 4 # define R300_INPUT_ROUTE_SELECT_ONE 5 # define R300_INPUT_ROUTE_SELECT_MASK 7 -# define R300_INPUT_ROUTE_X_SHIFT 0 -# define R300_INPUT_ROUTE_Y_SHIFT 3 -# define R300_INPUT_ROUTE_Z_SHIFT 6 -# define R300_INPUT_ROUTE_W_SHIFT 9 -# define R300_INPUT_ROUTE_ENABLE (15 << 12) +# define R300_INPUT_ROUTE_X_SHIFT 0 +# define R300_INPUT_ROUTE_Y_SHIFT 3 +# define R300_INPUT_ROUTE_Z_SHIFT 6 +# define R300_INPUT_ROUTE_W_SHIFT 9 +# define R300_INPUT_ROUTE_ENABLE (15 << 12) #define R300_VAP_INPUT_ROUTE_1_1 0x21E4 #define R300_VAP_INPUT_ROUTE_1_2 0x21E8 #define R300_VAP_INPUT_ROUTE_1_3 0x21EC @@ -221,79 +247,107 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_VAP_INPUT_ROUTE_1_6 0x21F8 #define R300_VAP_INPUT_ROUTE_1_7 0x21FC -/* END */ +/* END: Vertex data assembly */ /* gap */ -/* BEGIN: Upload vertex program and data -// The programmable vertex shader unit has a memory bank of unknown size -// that can be written to in 16 byte units by writing the address into -// UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs). -// -// Pointers into the memory bank are always in multiples of 16 bytes. -// -// The memory bank is divided into areas with fixed meaning. -// -// Starting at address UPLOAD_PROGRAM: Vertex program instructions. -// Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB), -// whereas the difference between known addresses suggests size 512. -// -// Starting at address UPLOAD_PARAMETERS: Vertex program parameters. -// Native reported limits and the VPI layout suggest size 256, whereas -// difference between known addresses suggests size 512. -// -// At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the -// floating point pointsize. The exact purpose of this state is uncertain, -// as there is also the R300_RE_POINTSIZE register. -// -// Multiple vertex programs and parameter sets can be loaded at once, -// which could explain the size discrepancy. */ + +/* BEGIN: Upload vertex program and data */ + +/* + * The programmable vertex shader unit has a memory bank of unknown size + * that can be written to in 16 byte units by writing the address into + * UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs). + * + * Pointers into the memory bank are always in multiples of 16 bytes. + * + * The memory bank is divided into areas with fixed meaning. + * + * Starting at address UPLOAD_PROGRAM: Vertex program instructions. + * Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB), + * whereas the difference between known addresses suggests size 512. + * + * Starting at address UPLOAD_PARAMETERS: Vertex program parameters. + * Native reported limits and the VPI layout suggest size 256, whereas + * difference between known addresses suggests size 512. + * + * At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the + * floating point pointsize. The exact purpose of this state is uncertain, + * as there is also the R300_RE_POINTSIZE register. + * + * Multiple vertex programs and parameter sets can be loaded at once, + * which could explain the size discrepancy. + */ #define R300_VAP_PVS_UPLOAD_ADDRESS 0x2200 # define R300_PVS_UPLOAD_PROGRAM 0x00000000 # define R300_PVS_UPLOAD_PARAMETERS 0x00000200 # define R300_PVS_UPLOAD_POINTSIZE 0x00000406 + /* gap */ + #define R300_VAP_PVS_UPLOAD_DATA 0x2208 -/* END */ + +/* END: Upload vertex program and data */ /* gap */ + /* I do not know the purpose of this register. However, I do know that -// it is set to 221C_CLEAR for clear operations and to 221C_NORMAL -// for normal rendering. */ + * it is set to 221C_CLEAR for clear operations and to 221C_NORMAL + * for normal rendering. + */ #define R300_VAP_UNKNOWN_221C 0x221C # define R300_221C_NORMAL 0x00000000 # define R300_221C_CLEAR 0x0001C000 +/* These seem to be per-pixel and per-vertex X and Y clipping planes. The first + * plane is per-pixel and the second plane is per-vertex. + * + * This was determined by experimentation alone but I believe it is correct. + * + * These registers are called X_QUAD0_1_FL to X_QUAD0_4_FL by glxtest. + */ +#define R300_VAP_CLIP_X_0 0x2220 +#define R300_VAP_CLIP_X_1 0x2224 +#define R300_VAP_CLIP_Y_0 0x2228 +#define R300_VAP_CLIP_Y_1 0x2230 + /* gap */ + /* Sometimes, END_OF_PKT and 0x2284=0 are the only commands sent between -// rendering commands and overwriting vertex program parameters. -// Therefore, I suspect writing zero to 0x2284 synchronizes the engine and -// avoids bugs caused by still running shaders reading bad data from memory. */ -#define R300_VAP_PVS_WAITIDLE 0x2284 /* GUESS */ + * rendering commands and overwriting vertex program parameters. + * Therefore, I suspect writing zero to 0x2284 synchronizes the engine and + * avoids bugs caused by still running shaders reading bad data from memory. + */ +#define R300_VAP_PVS_WAITIDLE 0x2284 /* GUESS */ /* Absolutely no clue what this register is about. */ #define R300_VAP_UNKNOWN_2288 0x2288 -# define R300_2288_R300 0x00750000 /* -- nh */ -# define R300_2288_RV350 0x0000FFFF /* -- Vladimir */ +# define R300_2288_R300 0x00750000 /* -- nh */ +# define R300_2288_RV350 0x0000FFFF /* -- Vladimir */ /* gap */ + /* Addresses are relative to the vertex program instruction area of the -// memory bank. PROGRAM_END points to the last instruction of the active -// program -// -// The meaning of the two UNKNOWN fields is obviously not known. However, -// experiments so far have shown that both *must* point to an instruction -// inside the vertex program, otherwise the GPU locks up. -// fglrx usually sets CNTL_3_UNKNOWN to the end of the program and -// CNTL_1_UNKNOWN points to instruction where last write to position takes place. -// Most likely this is used to ignore rest of the program in cases where group of verts arent visible. -// For some reason this "section" is sometimes accepted other instruction that have -// no relationship with position calculations. -*/ + * memory bank. PROGRAM_END points to the last instruction of the active + * program + * + * The meaning of the two UNKNOWN fields is obviously not known. However, + * experiments so far have shown that both *must* point to an instruction + * inside the vertex program, otherwise the GPU locks up. + * + * fglrx usually sets CNTL_3_UNKNOWN to the end of the program and + * R300_PVS_CNTL_1_POS_END_SHIFT points to instruction where last write to + * position takes place. + * + * Most likely this is used to ignore rest of the program in cases + * where group of verts arent visible. For some reason this "section" + * is sometimes accepted other instruction that have no relationship with + * position calculations. + */ #define R300_VAP_PVS_CNTL_1 0x22D0 # define R300_PVS_CNTL_1_PROGRAM_START_SHIFT 0 # define R300_PVS_CNTL_1_POS_END_SHIFT 10 # define R300_PVS_CNTL_1_PROGRAM_END_SHIFT 20 -/* Addresses are relative to the vertex program parameters area. */ +/* Addresses are relative the the vertex program parameters area. */ #define R300_VAP_PVS_CNTL_2 0x22D4 # define R300_PVS_CNTL_2_PARAM_OFFSET_SHIFT 0 # define R300_PVS_CNTL_2_PARAM_COUNT_SHIFT 16 @@ -302,23 +356,26 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_PVS_CNTL_3_PROGRAM_UNKNOWN2_SHIFT 0 /* The entire range from 0x2300 to 0x2AC inclusive seems to be used for -// immediate vertices */ + * immediate vertices + */ #define R300_VAP_VTX_COLOR_R 0x2464 #define R300_VAP_VTX_COLOR_G 0x2468 #define R300_VAP_VTX_COLOR_B 0x246C -#define R300_VAP_VTX_POS_0_X_1 0x2490 /* used for glVertex2*() */ +#define R300_VAP_VTX_POS_0_X_1 0x2490 /* used for glVertex2*() */ #define R300_VAP_VTX_POS_0_Y_1 0x2494 -#define R300_VAP_VTX_COLOR_PKD 0x249C /* RGBA */ -#define R300_VAP_VTX_POS_0_X_2 0x24A0 /* used for glVertex3*() */ +#define R300_VAP_VTX_COLOR_PKD 0x249C /* RGBA */ +#define R300_VAP_VTX_POS_0_X_2 0x24A0 /* used for glVertex3*() */ #define R300_VAP_VTX_POS_0_Y_2 0x24A4 #define R300_VAP_VTX_POS_0_Z_2 0x24A8 -#define R300_VAP_VTX_END_OF_PKT 0x24AC /* write 0 to indicate end of packet? */ +/* write 0 to indicate end of packet? */ +#define R300_VAP_VTX_END_OF_PKT 0x24AC /* gap */ /* These are values from r300_reg/r300_reg.h - they are known to be correct - and are here so we can use one register file instead of several - - Vladimir */ + * and are here so we can use one register file instead of several + * - Vladimir + */ #define R300_GB_VAP_RASTER_VTX_FMT_0 0x4000 # define R300_GB_VAP_RASTER_VTX_FMT_0__POS_PRESENT (1<<0) # define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_0_PRESENT (1<<1) @@ -341,14 +398,16 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21 /* UNK30 seems to enables point to quad transformation on textures - (or something closely related to that). - This bit is rather fatal at the time being due to lackings at pixel shader side */ + * (or something closely related to that). + * This bit is rather fatal at the time being due to lackings at pixel + * shader side + */ #define R300_GB_ENABLE 0x4008 # define R300_GB_POINT_STUFF_ENABLE (1<<0) # define R300_GB_LINE_STUFF_ENABLE (1<<1) # define R300_GB_TRIANGLE_STUFF_ENABLE (1<<2) # define R300_GB_STENCIL_AUTO_ENABLE (1<<4) -# define R300_GB_UNK30 (1<<30) +# define R300_GB_UNK31 (1<<31) /* each of the following is 2 bits wide */ #define R300_GB_TEX_REPLICATE 0 #define R300_GB_TEX_ST 1 @@ -383,11 +442,13 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_GB_MSPOS1__MS_Y5_SHIFT 20 # define R300_GB_MSPOS1__MSBD1 24 + #define R300_GB_TILE_CONFIG 0x4018 # define R300_GB_TILE_ENABLE (1<<0) # define R300_GB_TILE_PIPE_COUNT_RV300 0 # define R300_GB_TILE_PIPE_COUNT_R300 (3<<1) # define R300_GB_TILE_PIPE_COUNT_R420 (7<<1) +# define R300_GB_TILE_PIPE_COUNT_RV410 (3<<1) # define R300_GB_TILE_SIZE_8 0 # define R300_GB_TILE_SIZE_16 (1<<4) # define R300_GB_TILE_SIZE_32 (2<<4) @@ -442,17 +503,18 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_GB_W_SELECT_1 (1<<4) #define R300_GB_AA_CONFIG 0x4020 +# define R300_AA_DISABLE 0x00 # define R300_AA_ENABLE 0x01 # define R300_AA_SUBSAMPLES_2 0 # define R300_AA_SUBSAMPLES_3 (1<<1) # define R300_AA_SUBSAMPLES_4 (2<<1) # define R300_AA_SUBSAMPLES_6 (3<<1) -/* END */ - /* gap */ + /* Zero to flush caches. */ #define R300_TX_CNTL 0x4100 +#define R300_TX_FLUSH 0x0 /* The upper enable bits are guessed, based on fglrx reported limits. */ #define R300_TX_ENABLE 0x4104 @@ -474,24 +536,25 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_TX_ENABLE_15 (1 << 15) /* The pointsize is given in multiples of 6. The pointsize can be -// enormous: Clear() renders a single point that fills the entire -// framebuffer. */ + * enormous: Clear() renders a single point that fills the entire + * framebuffer. + */ #define R300_RE_POINTSIZE 0x421C # define R300_POINTSIZE_Y_SHIFT 0 -# define R300_POINTSIZE_Y_MASK (0xFFFF << 0) /* GUESS */ +# define R300_POINTSIZE_Y_MASK (0xFFFF << 0) /* GUESS */ # define R300_POINTSIZE_X_SHIFT 16 -# define R300_POINTSIZE_X_MASK (0xFFFF << 16) /* GUESS */ +# define R300_POINTSIZE_X_MASK (0xFFFF << 16) /* GUESS */ # define R300_POINTSIZE_MAX (R300_POINTSIZE_Y_MASK / 6) /* The line width is given in multiples of 6. - In default mode lines are classified as vertical lines. - HO: horizontal - VE: vertical or horizontal - HO & VE: no classification -*/ + * In default mode lines are classified as vertical lines. + * HO: horizontal + * VE: vertical or horizontal + * HO & VE: no classification + */ #define R300_RE_LINE_CNT 0x4234 # define R300_LINESIZE_SHIFT 0 -# define R300_LINESIZE_MASK (0xFFFF << 0) /* GUESS */ +# define R300_LINESIZE_MASK (0xFFFF << 0) /* GUESS */ # define R300_LINESIZE_MAX (R300_LINESIZE_MASK / 6) # define R300_LINE_CNT_HO (1 << 16) # define R300_LINE_CNT_VE (1 << 17) @@ -499,6 +562,9 @@ I am fairly certain that they are correct unless stated otherwise in comments. /* Some sort of scale or clamp value for texcoordless textures. */ #define R300_RE_UNK4238 0x4238 +/* Something shade related */ +#define R300_RE_SHADE 0x4274 + #define R300_RE_SHADE_MODEL 0x4278 # define R300_RE_SHADE_MODEL_SMOOTH 0x3aaaa # define R300_RE_SHADE_MODEL_FLAT 0x39595 @@ -513,24 +579,31 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_PM_BACK_LINE (1 << 7) # define R300_PM_BACK_FILL (1 << 8) +/* Fog parameters */ +#define R300_RE_FOG_SCALE 0x4294 +#define R300_RE_FOG_START 0x4298 + /* Not sure why there are duplicate of factor and constant values. - My best guess so far is that there are seperate zbiases for test and write. - Ordering might be wrong. - Some of the tests indicate that fgl has a fallback implementation of zbias - via pixel shaders. */ + * My best guess so far is that there are seperate zbiases for test and write. + * Ordering might be wrong. + * Some of the tests indicate that fgl has a fallback implementation of zbias + * via pixel shaders. + */ +#define R300_RE_ZBIAS_CNTL 0x42A0 /* GUESS */ #define R300_RE_ZBIAS_T_FACTOR 0x42A4 #define R300_RE_ZBIAS_T_CONSTANT 0x42A8 #define R300_RE_ZBIAS_W_FACTOR 0x42AC #define R300_RE_ZBIAS_W_CONSTANT 0x42B0 /* This register needs to be set to (1<<1) for RV350 to correctly - perform depth test (see --vb-triangles in r300_demo) - Don't know about other chips. - Vladimir - This is set to 3 when GL_POLYGON_OFFSET_FILL is on. - My guess is that there are two bits for each zbias primitive (FILL, LINE, POINT). - One to enable depth test and one for depth write. - Yet this doesnt explain why depth writes work ... - */ + * perform depth test (see --vb-triangles in r300_demo) + * Don't know about other chips. - Vladimir + * This is set to 3 when GL_POLYGON_OFFSET_FILL is on. + * My guess is that there are two bits for each zbias primitive + * (FILL, LINE, POINT). + * One to enable depth test and one for depth write. + * Yet this doesnt explain why depth writes work ... + */ #define R300_RE_OCCLUSION_CNTL 0x42B4 # define R300_OCCLUSION_ON (1<<1) @@ -540,30 +613,38 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FRONT_FACE_CCW (0 << 2) # define R300_FRONT_FACE_CW (1 << 2) -/* BEGIN: Rasterization / Interpolators - many guesses -// 0_UNKNOWN_18 has always been set except for clear operations. -// TC_CNT is the number of incoming texture coordinate sets (i.e. it depends -// on the vertex program, *not* the fragment program) */ + +/* BEGIN: Rasterization / Interpolators - many guesses */ + +/* 0_UNKNOWN_18 has always been set except for clear operations. + * TC_CNT is the number of incoming texture coordinate sets (i.e. it depends + * on the vertex program, *not* the fragment program) + */ #define R300_RS_CNTL_0 0x4300 # define R300_RS_CNTL_TC_CNT_SHIFT 2 # define R300_RS_CNTL_TC_CNT_MASK (7 << 2) -# define R300_RS_CNTL_CI_CNT_SHIFT 7 /* number of color interpolators used */ + /* number of color interpolators used */ +# define R300_RS_CNTL_CI_CNT_SHIFT 7 # define R300_RS_CNTL_0_UNKNOWN_18 (1 << 18) -/* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n register. */ + /* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n + register. */ #define R300_RS_CNTL_1 0x4304 /* gap */ + /* Only used for texture coordinates. -// Use the source field to route texture coordinate input from the vertex program -// to the desired interpolator. Note that the source field is relative to the -// outputs the vertex program *actually* writes. If a vertex program only writes -// texcoord[1], this will be source index 0. -// Set INTERP_USED on all interpolators that produce data used by the -// fragment program. INTERP_USED looks like a swizzling mask, but -// I haven't seen it used that way. -// -// Note: The _UNKNOWN constants are always set in their respective register. -// I don't know if this is necessary. */ + * Use the source field to route texture coordinate input from the + * vertex program to the desired interpolator. Note that the source + * field is relative to the outputs the vertex program *actually* + * writes. If a vertex program only writes texcoord[1], this will + * be source index 0. + * Set INTERP_USED on all interpolators that produce data used by + * the fragment program. INTERP_USED looks like a swizzling mask, + * but I haven't seen it used that way. + * + * Note: The _UNKNOWN constants are always set in their respective + * register. I don't know if this is necessary. + */ #define R300_RS_INTERP_0 0x4310 #define R300_RS_INTERP_1 0x4314 # define R300_RS_INTERP_1_UNKNOWN 0x40 @@ -580,54 +661,63 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_RS_INTERP_USED 0x00D10000 /* These DWORDs control how vertex data is routed into fragment program -// registers, after interpolators. */ + * registers, after interpolators. + */ #define R300_RS_ROUTE_0 0x4330 #define R300_RS_ROUTE_1 0x4334 #define R300_RS_ROUTE_2 0x4338 -#define R300_RS_ROUTE_3 0x433C /* GUESS */ -#define R300_RS_ROUTE_4 0x4340 /* GUESS */ -#define R300_RS_ROUTE_5 0x4344 /* GUESS */ -#define R300_RS_ROUTE_6 0x4348 /* GUESS */ -#define R300_RS_ROUTE_7 0x434C /* GUESS */ +#define R300_RS_ROUTE_3 0x433C /* GUESS */ +#define R300_RS_ROUTE_4 0x4340 /* GUESS */ +#define R300_RS_ROUTE_5 0x4344 /* GUESS */ +#define R300_RS_ROUTE_6 0x4348 /* GUESS */ +#define R300_RS_ROUTE_7 0x434C /* GUESS */ # define R300_RS_ROUTE_SOURCE_INTERP_0 0 # define R300_RS_ROUTE_SOURCE_INTERP_1 1 # define R300_RS_ROUTE_SOURCE_INTERP_2 2 # define R300_RS_ROUTE_SOURCE_INTERP_3 3 # define R300_RS_ROUTE_SOURCE_INTERP_4 4 -# define R300_RS_ROUTE_SOURCE_INTERP_5 5 /* GUESS */ -# define R300_RS_ROUTE_SOURCE_INTERP_6 6 /* GUESS */ -# define R300_RS_ROUTE_SOURCE_INTERP_7 7 /* GUESS */ -# define R300_RS_ROUTE_ENABLE (1 << 3) /* GUESS */ +# define R300_RS_ROUTE_SOURCE_INTERP_5 5 /* GUESS */ +# define R300_RS_ROUTE_SOURCE_INTERP_6 6 /* GUESS */ +# define R300_RS_ROUTE_SOURCE_INTERP_7 7 /* GUESS */ +# define R300_RS_ROUTE_ENABLE (1 << 3) /* GUESS */ # define R300_RS_ROUTE_DEST_SHIFT 6 -# define R300_RS_ROUTE_DEST_MASK (31 << 6) /* GUESS */ +# define R300_RS_ROUTE_DEST_MASK (31 << 6) /* GUESS */ /* Special handling for color: When the fragment program uses color, -// the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the -// color register index. */ + * the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the + * color register index. + * + * Apperently you may set the R300_RS_ROUTE_0_COLOR bit, but not provide any + * R300_RS_ROUTE_0_COLOR_DEST value; this setup is used for clearing the state. + * See r300_ioctl.c:r300EmitClearState. I'm not sure if this setup is strictly + * correct or not. - Oliver. + */ # define R300_RS_ROUTE_0_COLOR (1 << 14) # define R300_RS_ROUTE_0_COLOR_DEST_SHIFT 17 -# define R300_RS_ROUTE_0_COLOR_DEST_MASK (31 << 17) /* GUESS */ +# define R300_RS_ROUTE_0_COLOR_DEST_MASK (31 << 17) /* GUESS */ /* As above, but for secondary color */ # define R300_RS_ROUTE_1_COLOR1 (1 << 14) # define R300_RS_ROUTE_1_COLOR1_DEST_SHIFT 17 # define R300_RS_ROUTE_1_COLOR1_DEST_MASK (31 << 17) # define R300_RS_ROUTE_1_UNKNOWN11 (1 << 11) -/* END */ - -/* BEGIN: Scissors and cliprects -// There are four clipping rectangles. Their corner coordinates are inclusive. -// Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending -// on whether the pixel is inside cliprects 0-3, respectively. For example, -// if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned -// the number 3 (binary 0011). -// Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set, -// the pixel is rasterized. -// -// In addition to this, there is a scissors rectangle. Only pixels inside the -// scissors rectangle are drawn. (coordinates are inclusive) -// -// For some reason, the top-left corner of the framebuffer is at (1440, 1440) -// for the purpose of clipping and scissors. */ +/* END: Rasterization / Interpolators - many guesses */ + +/* BEGIN: Scissors and cliprects */ + +/* There are four clipping rectangles. Their corner coordinates are inclusive. + * Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending + * on whether the pixel is inside cliprects 0-3, respectively. For example, + * if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned + * the number 3 (binary 0011). + * Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set, + * the pixel is rasterized. + * + * In addition to this, there is a scissors rectangle. Only pixels inside the + * scissors rectangle are drawn. (coordinates are inclusive) + * + * For some reason, the top-left corner of the framebuffer is at (1440, 1440) + * for the purpose of clipping and scissors. + */ #define R300_RE_CLIPRECT_TL_0 0x43B0 #define R300_RE_CLIPRECT_BR_0 0x43B4 #define R300_RE_CLIPRECT_TL_1 0x43B8 @@ -661,6 +751,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_CLIP_3210 (1 << 15) /* gap */ + #define R300_RE_SCISSORS_TL 0x43E0 #define R300_RE_SCISSORS_BR 0x43E4 # define R300_SCISSORS_OFFSET 1440 @@ -668,12 +759,15 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_SCISSORS_X_MASK (0x1FFF << 0) # define R300_SCISSORS_Y_SHIFT 13 # define R300_SCISSORS_Y_MASK (0x1FFF << 13) -/* END */ +/* END: Scissors and cliprects */ -/* BEGIN: Texture specification -// The texture specification dwords are grouped by meaning and not by texture unit. -// This means that e.g. the offset for texture image unit N is found in register -// TX_OFFSET_0 + (4*N) */ +/* BEGIN: Texture specification */ + +/* + * The texture specification dwords are grouped by meaning and not by texture + * unit. This means that e.g. the offset for texture image unit N is found in + * register TX_OFFSET_0 + (4*N) + */ #define R300_TX_FILTER_0 0x4400 # define R300_TX_REPEAT 0 # define R300_TX_MIRRORED 1 @@ -697,13 +791,14 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_TX_MIN_FILTER_LINEAR_MIP_LINEAR (10 << 11) /* NOTE: NEAREST doesnt seem to exist. - Im not seting MAG_FILTER_MASK and (3 << 11) on for all - anisotropy modes because that would void selected mag filter */ -# define R300_TX_MIN_FILTER_ANISO_NEAREST ((0 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) -# define R300_TX_MIN_FILTER_ANISO_LINEAR ((0 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) -# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST ((1 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) -# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR ((2 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) -# define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) ) + * Im not seting MAG_FILTER_MASK and (3 << 11) on for all + * anisotropy modes because that would void selected mag filter + */ +# define R300_TX_MIN_FILTER_ANISO_NEAREST (0 << 13) +# define R300_TX_MIN_FILTER_ANISO_LINEAR (0 << 13) +# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST (1 << 13) +# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR (2 << 13) +# define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) ) # define R300_TX_MAX_ANISO_1_TO_1 (0 << 21) # define R300_TX_MAX_ANISO_2_TO_1 (2 << 21) # define R300_TX_MAX_ANISO_4_TO_1 (4 << 21) @@ -734,10 +829,10 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_TX_HEIGHTMASK_SHIFT 11 # define R300_TX_HEIGHTMASK_MASK (2047 << 11) # define R300_TX_UNK23 (1 << 23) -# define R300_TX_SIZE_SHIFT 26 /* largest of width, height */ -# define R300_TX_SIZE_MASK (15 << 26) -# define R300_TX_SIZE_PROJECTED (1<<30) -# define R300_TX_SIZE_TXPITCH_EN (1<<31) +# define R300_TX_MAX_MIP_LEVEL_SHIFT 26 +# define R300_TX_MAX_MIP_LEVEL_MASK (0xf << 26) +# define R300_TX_SIZE_PROJECTED (1<<30) +# define R300_TX_SIZE_TXPITCH_EN (1<<31) #define R300_TX_FORMAT_0 0x44C0 /* The interpretation of the format word by Wladimir van der Laan */ /* The X, Y, Z and W refer to the layout of the components. @@ -761,11 +856,11 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_TX_FORMAT_DXT1 0xF # define R300_TX_FORMAT_DXT3 0x10 # define R300_TX_FORMAT_DXT5 0x11 -# define R300_TX_FORMAT_D3DMFT_CxV8U8 0x12 /* no swizzle */ -# define R300_TX_FORMAT_A8R8G8B8 0x13 /* no swizzle */ -# define R300_TX_FORMAT_B8G8_B8G8 0x14 /* no swizzle */ -# define R300_TX_FORMAT_G8R8_G8B8 0x15 /* no swizzle */ - /* 0x16 - some 16 bit green format.. ?? */ +# define R300_TX_FORMAT_D3DMFT_CxV8U8 0x12 /* no swizzle */ +# define R300_TX_FORMAT_A8R8G8B8 0x13 /* no swizzle */ +# define R300_TX_FORMAT_B8G8_B8G8 0x14 /* no swizzle */ +# define R300_TX_FORMAT_G8R8_G8B8 0x15 /* no swizzle */ + /* 0x16 - some 16 bit green format.. ?? */ # define R300_TX_FORMAT_UNK25 (1 << 25) /* no swizzle */ # define R300_TX_FORMAT_CUBIC_MAP (1 << 26) @@ -793,23 +888,26 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_TX_FORMAT_W 3 # define R300_TX_FORMAT_ZERO 4 # define R300_TX_FORMAT_ONE 5 -# define R300_TX_FORMAT_CUT_Z 6 /* 2.0*Z, everything above 1.0 is set to 0.0 */ -# define R300_TX_FORMAT_CUT_W 7 /* 2.0*W, everything above 1.0 is set to 0.0 */ + /* 2.0*Z, everything above 1.0 is set to 0.0 */ +# define R300_TX_FORMAT_CUT_Z 6 + /* 2.0*W, everything above 1.0 is set to 0.0 */ +# define R300_TX_FORMAT_CUT_W 7 # define R300_TX_FORMAT_B_SHIFT 18 # define R300_TX_FORMAT_G_SHIFT 15 # define R300_TX_FORMAT_R_SHIFT 12 # define R300_TX_FORMAT_A_SHIFT 9 /* Convenience macro to take care of layout and swizzling */ -# define R300_EASY_TX_FORMAT(B, G, R, A, FMT) (\ - ((R300_TX_FORMAT_##B)< 0.5, return ARG0, else return ARG1 + * - CMP: If ARG2 < 0, return ARG1, else return ARG0 + * - FLR: use FRC+MAD + * - XPD: use MAD+MAD + * - SGE, SLT: use MAD+CMP + * - RSQ: use ABS modifier for argument + * - Use OUTC_REPL_ALPHA to write results of an alpha-only operation + * (e.g. RCP) into color register + * - apparently, there's no quick DST operation + * - fglrx set FPI2_UNKNOWN_31 on a "MAD fragment.color, tmp0, tmp1, tmp2" + * - fglrx set FPI2_UNKNOWN_31 on a "MAX r2, r1, c0" + * - fglrx once set FPI0_UNKNOWN_31 on a "FRC r1, r1" + * + * Operand selection + * First stage selects three sources from the available registers and + * constant parameters. This is defined in INSTR1 (color) and INSTR3 (alpha). + * fglrx sorts the three source fields: Registers before constants, + * lower indices before higher indices; I do not know whether this is + * necessary. + * + * fglrx fills unused sources with "read constant 0" + * According to specs, you cannot select more than two different constants. + * + * Second stage selects the operands from the sources. This is defined in + * INSTR0 (color) and INSTR2 (alpha). You can also select the special constants + * zero and one. + * Swizzling and negation happens in this stage, as well. + * + * Important: Color and alpha seem to be mostly separate, i.e. their sources + * selection appears to be fully independent (the register storage is probably + * physically split into a color and an alpha section). + * However (because of the apparent physical split), there is some interaction + * WRT swizzling. If, for example, you want to load an R component into an + * Alpha operand, this R component is taken from a *color* source, not from + * an alpha source. The corresponding register doesn't even have to appear in + * the alpha sources list. (I hope this all makes sense to you) + * + * Destination selection + * The destination register index is in FPI1 (color) and FPI3 (alpha) + * together with enable bits. + * There are separate enable bits for writing into temporary registers + * (DSTC_REG_* /DSTA_REG) and and program output registers (DSTC_OUTPUT_* + * /DSTA_OUTPUT). You can write to both at once, or not write at all (the + * same index must be used for both). + * + * Note: There is a special form for LRP + * - Argument order is the same as in ARB_fragment_program. + * - Operation is MAD + * - ARG1 is set to ARGC_SRC1C_LRP/ARGC_SRC1A_LRP + * - Set FPI0/FPI2_SPECIAL_LRP + * Arbitrary LRP (including support for swizzling) requires vanilla MAD+MAD + */ #define R300_PFS_INSTR1_0 0x46C0 # define R300_FPI1_SRC0C_SHIFT 0 # define R300_FPI1_SRC0C_MASK (31 << 0) @@ -982,6 +1095,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FPI1_SRC2C_SHIFT 12 # define R300_FPI1_SRC2C_MASK (31 << 12) # define R300_FPI1_SRC2C_CONST (1 << 17) +# define R300_FPI1_SRC_MASK 0x0003ffff # define R300_FPI1_DSTC_SHIFT 18 # define R300_FPI1_DSTC_MASK (31 << 18) # define R300_FPI1_DSTC_REG_MASK_SHIFT 23 @@ -1003,6 +1117,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FPI3_SRC2A_SHIFT 12 # define R300_FPI3_SRC2A_MASK (31 << 12) # define R300_FPI3_SRC2A_CONST (1 << 17) +# define R300_FPI3_SRC_MASK 0x0003ffff # define R300_FPI3_DSTA_SHIFT 18 # define R300_FPI3_DSTA_MASK (31 << 18) # define R300_FPI3_DSTA_REG (1 << 23) @@ -1028,7 +1143,8 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FPI0_ARGC_SRC1C_LRP 15 # define R300_FPI0_ARGC_ZERO 20 # define R300_FPI0_ARGC_ONE 21 -# define R300_FPI0_ARGC_HALF 22 /* GUESS */ + /* GUESS */ +# define R300_FPI0_ARGC_HALF 22 # define R300_FPI0_ARGC_SRC0C_YZX 23 # define R300_FPI0_ARGC_SRC1C_YZX 24 # define R300_FPI0_ARGC_SRC2C_YZX 25 @@ -1057,6 +1173,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FPI0_OUTC_DP4 (2 << 23) # define R300_FPI0_OUTC_MIN (4 << 23) # define R300_FPI0_OUTC_MAX (5 << 23) +# define R300_FPI0_OUTC_CMPH (7 << 23) # define R300_FPI0_OUTC_CMP (8 << 23) # define R300_FPI0_OUTC_FRC (9 << 23) # define R300_FPI0_OUTC_REPL_ALPHA (10 << 23) @@ -1079,20 +1196,23 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FPI2_ARGA_SRC1A_LRP 15 # define R300_FPI2_ARGA_ZERO 16 # define R300_FPI2_ARGA_ONE 17 -# define R300_FPI2_ARGA_HALF 18 /* GUESS */ - + /* GUESS */ +# define R300_FPI2_ARGA_HALF 18 # define R300_FPI2_ARG0A_SHIFT 0 # define R300_FPI2_ARG0A_MASK (31 << 0) # define R300_FPI2_ARG0A_NEG (1 << 5) -# define R300_FPI2_ARG0A_ABS (1 << 6) /* GUESS */ + /* GUESS */ +# define R300_FPI2_ARG0A_ABS (1 << 6) # define R300_FPI2_ARG1A_SHIFT 7 # define R300_FPI2_ARG1A_MASK (31 << 7) # define R300_FPI2_ARG1A_NEG (1 << 12) -# define R300_FPI2_ARG1A_ABS (1 << 13) /* GUESS */ + /* GUESS */ +# define R300_FPI2_ARG1A_ABS (1 << 13) # define R300_FPI2_ARG2A_SHIFT 14 # define R300_FPI2_ARG2A_MASK (31 << 14) # define R300_FPI2_ARG2A_NEG (1 << 19) -# define R300_FPI2_ARG2A_ABS (1 << 20) /* GUESS */ + /* GUESS */ +# define R300_FPI2_ARG2A_ABS (1 << 20) # define R300_FPI2_SPECIAL_LRP (1 << 21) # define R300_FPI2_OUTA_MAD (0 << 23) # define R300_FPI2_OUTA_DP4 (1 << 23) @@ -1106,9 +1226,19 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_FPI2_OUTA_RSQ (11 << 23) # define R300_FPI2_OUTA_SAT (1 << 30) # define R300_FPI2_UNKNOWN_31 (1 << 31) -/* END */ +/* END: Fragment program instruction set */ + +/* Fog state and color */ +#define R300_RE_FOG_STATE 0x4BC0 +# define R300_FOG_ENABLE (1 << 0) +# define R300_FOG_MODE_LINEAR (0 << 1) +# define R300_FOG_MODE_EXP (1 << 1) +# define R300_FOG_MODE_EXP2 (2 << 1) +# define R300_FOG_MODE_MASK (3 << 1) +#define R300_FOG_COLOR_R 0x4BC8 +#define R300_FOG_COLOR_G 0x4BCC +#define R300_FOG_COLOR_B 0x4BD0 -/* gap */ #define R300_PP_ALPHA_TEST 0x4BD4 # define R300_REF_ALPHA_MASK 0x000000ff # define R300_ALPHA_TEST_FAIL (0 << 8) @@ -1123,6 +1253,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_ALPHA_TEST_ENABLE (1 << 11) /* gap */ + /* Fragment program parameters in 7.16 floating point */ #define R300_PFS_PARAM_0_X 0x4C00 #define R300_PFS_PARAM_0_Y 0x4C04 @@ -1135,45 +1266,48 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_PFS_PARAM_31_W 0x4DFC /* Notes: -// - AFAIK fglrx always sets BLEND_UNKNOWN when blending is used in the application -// - AFAIK fglrx always sets BLEND_NO_SEPARATE when CBLEND and ABLEND are set to the same -// function (both registers are always set up completely in any case) -// - Most blend flags are simply copied from R200 and not tested yet */ + * - AFAIK fglrx always sets BLEND_UNKNOWN when blending is used in + * the application + * - AFAIK fglrx always sets BLEND_NO_SEPARATE when CBLEND and ABLEND + * are set to the same + * function (both registers are always set up completely in any case) + * - Most blend flags are simply copied from R200 and not tested yet + */ #define R300_RB3D_CBLEND 0x4E04 #define R300_RB3D_ABLEND 0x4E08 - /* the following only appear in CBLEND */ +/* the following only appear in CBLEND */ # define R300_BLEND_ENABLE (1 << 0) # define R300_BLEND_UNKNOWN (3 << 1) # define R300_BLEND_NO_SEPARATE (1 << 3) - /* the following are shared between CBLEND and ABLEND */ +/* the following are shared between CBLEND and ABLEND */ # define R300_FCN_MASK (3 << 12) # define R300_COMB_FCN_ADD_CLAMP (0 << 12) # define R300_COMB_FCN_ADD_NOCLAMP (1 << 12) # define R300_COMB_FCN_SUB_CLAMP (2 << 12) # define R300_COMB_FCN_SUB_NOCLAMP (3 << 12) -# define R300_SRC_BLEND_GL_ZERO (32 << 16) -# define R300_SRC_BLEND_GL_ONE (33 << 16) -# define R300_SRC_BLEND_GL_SRC_COLOR (34 << 16) -# define R300_SRC_BLEND_GL_ONE_MINUS_SRC_COLOR (35 << 16) -# define R300_SRC_BLEND_GL_DST_COLOR (36 << 16) -# define R300_SRC_BLEND_GL_ONE_MINUS_DST_COLOR (37 << 16) -# define R300_SRC_BLEND_GL_SRC_ALPHA (38 << 16) -# define R300_SRC_BLEND_GL_ONE_MINUS_SRC_ALPHA (39 << 16) -# define R300_SRC_BLEND_GL_DST_ALPHA (40 << 16) -# define R300_SRC_BLEND_GL_ONE_MINUS_DST_ALPHA (41 << 16) -# define R300_SRC_BLEND_GL_SRC_ALPHA_SATURATE (42 << 16) -# define R300_SRC_BLEND_MASK (63 << 16) -# define R300_DST_BLEND_GL_ZERO (32 << 24) -# define R300_DST_BLEND_GL_ONE (33 << 24) -# define R300_DST_BLEND_GL_SRC_COLOR (34 << 24) -# define R300_DST_BLEND_GL_ONE_MINUS_SRC_COLOR (35 << 24) -# define R300_DST_BLEND_GL_DST_COLOR (36 << 24) -# define R300_DST_BLEND_GL_ONE_MINUS_DST_COLOR (37 << 24) -# define R300_DST_BLEND_GL_SRC_ALPHA (38 << 24) -# define R300_DST_BLEND_GL_ONE_MINUS_SRC_ALPHA (39 << 24) -# define R300_DST_BLEND_GL_DST_ALPHA (40 << 24) -# define R300_DST_BLEND_GL_ONE_MINUS_DST_ALPHA (41 << 24) -# define R300_DST_BLEND_MASK (63 << 24) +# define R300_COMB_FCN_MIN (4 << 12) +# define R300_COMB_FCN_MAX (5 << 12) +# define R300_COMB_FCN_RSUB_CLAMP (6 << 12) +# define R300_COMB_FCN_RSUB_NOCLAMP (7 << 12) +# define R300_BLEND_GL_ZERO (32) +# define R300_BLEND_GL_ONE (33) +# define R300_BLEND_GL_SRC_COLOR (34) +# define R300_BLEND_GL_ONE_MINUS_SRC_COLOR (35) +# define R300_BLEND_GL_DST_COLOR (36) +# define R300_BLEND_GL_ONE_MINUS_DST_COLOR (37) +# define R300_BLEND_GL_SRC_ALPHA (38) +# define R300_BLEND_GL_ONE_MINUS_SRC_ALPHA (39) +# define R300_BLEND_GL_DST_ALPHA (40) +# define R300_BLEND_GL_ONE_MINUS_DST_ALPHA (41) +# define R300_BLEND_GL_SRC_ALPHA_SATURATE (42) +# define R300_BLEND_GL_CONST_COLOR (43) +# define R300_BLEND_GL_ONE_MINUS_CONST_COLOR (44) +# define R300_BLEND_GL_CONST_ALPHA (45) +# define R300_BLEND_GL_ONE_MINUS_CONST_ALPHA (46) +# define R300_BLEND_MASK (63) +# define R300_SRC_BLEND_SHIFT (16) +# define R300_DST_BLEND_SHIFT (24) +#define R300_RB3D_BLEND_COLOR 0x4E10 #define R300_RB3D_COLORMASK 0x4E0C # define R300_COLORMASK0_B (1<<0) # define R300_COLORMASK0_G (1<<1) @@ -1181,41 +1315,49 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_COLORMASK0_A (1<<3) /* gap */ + #define R300_RB3D_COLOROFFSET0 0x4E28 -# define R300_COLOROFFSET_MASK 0xFFFFFFF0 /* GUESS */ -#define R300_RB3D_COLOROFFSET1 0x4E2C /* GUESS */ -#define R300_RB3D_COLOROFFSET2 0x4E30 /* GUESS */ -#define R300_RB3D_COLOROFFSET3 0x4E34 /* GUESS */ +# define R300_COLOROFFSET_MASK 0xFFFFFFF0 /* GUESS */ +#define R300_RB3D_COLOROFFSET1 0x4E2C /* GUESS */ +#define R300_RB3D_COLOROFFSET2 0x4E30 /* GUESS */ +#define R300_RB3D_COLOROFFSET3 0x4E34 /* GUESS */ + /* gap */ + /* Bit 16: Larger tiles -// Bit 17: 4x2 tiles -// Bit 18: Extremely weird tile like, but some pixels duplicated? */ + * Bit 17: 4x2 tiles + * Bit 18: Extremely weird tile like, but some pixels duplicated? + */ #define R300_RB3D_COLORPITCH0 0x4E38 -# define R300_COLORPITCH_MASK 0x00001FF8 /* GUESS */ -# define R300_COLOR_TILE_ENABLE (1 << 16) /* GUESS */ -# define R300_COLOR_MICROTILE_ENABLE (1 << 17) /* GUESS */ -# define R300_COLOR_ENDIAN_NO_SWAP (0 << 18) /* GUESS */ -# define R300_COLOR_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */ -# define R300_COLOR_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */ +# define R300_COLORPITCH_MASK 0x00001FF8 /* GUESS */ +# define R300_COLOR_TILE_ENABLE (1 << 16) /* GUESS */ +# define R300_COLOR_MICROTILE_ENABLE (1 << 17) /* GUESS */ +# define R300_COLOR_ENDIAN_NO_SWAP (0 << 18) /* GUESS */ +# define R300_COLOR_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */ +# define R300_COLOR_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */ # define R300_COLOR_FORMAT_RGB565 (2 << 22) # define R300_COLOR_FORMAT_ARGB8888 (3 << 22) -#define R300_RB3D_COLORPITCH1 0x4E3C /* GUESS */ -#define R300_RB3D_COLORPITCH2 0x4E40 /* GUESS */ -#define R300_RB3D_COLORPITCH3 0x4E44 /* GUESS */ +#define R300_RB3D_COLORPITCH1 0x4E3C /* GUESS */ +#define R300_RB3D_COLORPITCH2 0x4E40 /* GUESS */ +#define R300_RB3D_COLORPITCH3 0x4E44 /* GUESS */ /* gap */ + /* Guess by Vladimir. -// Set to 0A before 3D operations, set to 02 afterwards. */ + * Set to 0A before 3D operations, set to 02 afterwards. + */ #define R300_RB3D_DSTCACHE_CTLSTAT 0x4E4C -# define R300_RB3D_DSTCACHE_02 0x00000002 -# define R300_RB3D_DSTCACHE_0A 0x0000000A +# define R300_RB3D_DSTCACHE_UNKNOWN_02 0x00000002 +# define R300_RB3D_DSTCACHE_UNKNOWN_0A 0x0000000A /* gap */ -/* There seems to be no "write only" setting, so use Z-test = ALWAYS for this. */ -/* Bit (1<<8) is the "test" bit. so plain write is 6 - vd */ +/* There seems to be no "write only" setting, so use Z-test = ALWAYS + * for this. + * Bit (1<<8) is the "test" bit. so plain write is 6 - vd + */ #define R300_RB3D_ZSTENCIL_CNTL_0 0x4F00 -# define R300_RB3D_Z_DISABLED_1 0x00000010 /* GUESS */ -# define R300_RB3D_Z_DISABLED_2 0x00000014 /* GUESS */ +# define R300_RB3D_Z_DISABLED_1 0x00000010 +# define R300_RB3D_Z_DISABLED_2 0x00000014 # define R300_RB3D_Z_TEST 0x00000012 # define R300_RB3D_Z_TEST_AND_WRITE 0x00000016 # define R300_RB3D_Z_WRITE_ONLY 0x00000006 @@ -1226,7 +1368,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_RB3D_STENCIL_ENABLE 0x00000001 #define R300_RB3D_ZSTENCIL_CNTL_1 0x4F04 - /* functions */ + /* functions */ # define R300_ZS_NEVER 0 # define R300_ZS_LESS 1 # define R300_ZS_LEQUAL 2 @@ -1236,7 +1378,7 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_ZS_NOTEQUAL 6 # define R300_ZS_ALWAYS 7 # define R300_ZS_MASK 7 - /* operations */ + /* operations */ # define R300_ZS_KEEP 0 # define R300_ZS_ZERO 1 # define R300_ZS_REPLACE 2 @@ -1245,9 +1387,8 @@ I am fairly certain that they are correct unless stated otherwise in comments. # define R300_ZS_INVERT 5 # define R300_ZS_INCR_WRAP 6 # define R300_ZS_DECR_WRAP 7 - - /* front and back refer to operations done for front - and back faces, i.e. separate stencil function support */ + /* front and back refer to operations done for front + and back faces, i.e. separate stencil function support */ # define R300_RB3D_ZS1_DEPTH_FUNC_SHIFT 0 # define R300_RB3D_ZS1_FRONT_FUNC_SHIFT 3 # define R300_RB3D_ZS1_FRONT_FAIL_OP_SHIFT 6 @@ -1269,45 +1410,64 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_RB3D_ZSTENCIL_FORMAT 0x4F10 # define R300_DEPTH_FORMAT_16BIT_INT_Z (0 << 0) # define R300_DEPTH_FORMAT_24BIT_INT_Z (2 << 0) + /* 16 bit format or some aditional bit ? */ +# define R300_DEPTH_FORMAT_UNK32 (32 << 0) + +#define R300_RB3D_EARLY_Z 0x4F14 +# define R300_EARLY_Z_DISABLE (0 << 0) +# define R300_EARLY_Z_ENABLE (1 << 0) + +/* gap */ + +#define R300_RB3D_ZCACHE_CTLSTAT 0x4F18 /* GUESS */ +# define R300_RB3D_ZCACHE_UNKNOWN_01 0x1 +# define R300_RB3D_ZCACHE_UNKNOWN_03 0x3 /* gap */ + #define R300_RB3D_DEPTHOFFSET 0x4F20 #define R300_RB3D_DEPTHPITCH 0x4F24 -# define R300_DEPTHPITCH_MASK 0x00001FF8 /* GUESS */ -# define R300_DEPTH_TILE_ENABLE (1 << 16) /* GUESS */ -# define R300_DEPTH_MICROTILE_ENABLE (1 << 17) /* GUESS */ -# define R300_DEPTH_ENDIAN_NO_SWAP (0 << 18) /* GUESS */ -# define R300_DEPTH_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */ -# define R300_DEPTH_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */ - -/* BEGIN: Vertex program instruction set -// Every instruction is four dwords long: -// DWORD 0: output and opcode -// DWORD 1: first argument -// DWORD 2: second argument -// DWORD 3: third argument -// -// Notes: -// - ABS r, a is implemented as MAX r, a, -a -// - MOV is implemented as ADD to zero -// - XPD is implemented as MUL + MAD -// - FLR is implemented as FRC + ADD -// - apparently, fglrx tries to schedule instructions so that there is at least -// one instruction between the write to a temporary and the first read -// from said temporary; however, violations of this scheduling are allowed -// - register indices seem to be unrelated with OpenGL aliasing to conventional state -// - only one attribute and one parameter can be loaded at a time; however, the -// same attribute/parameter can be used for more than one argument -// - the second software argument for POW is the third hardware argument (no idea why) -// - MAD with only temporaries as input seems to use VPI_OUT_SELECT_MAD_2 -// -// There is some magic surrounding LIT: -// The single argument is replicated across all three inputs, but swizzled: -// First argument: xyzy -// Second argument: xyzx -// Third argument: xyzw -// Whenever the result is used later in the fragment program, fglrx forces x and w -// to be 1.0 in the input selection; I don't know whether this is strictly necessary */ +# define R300_DEPTHPITCH_MASK 0x00001FF8 /* GUESS */ +# define R300_DEPTH_TILE_ENABLE (1 << 16) /* GUESS */ +# define R300_DEPTH_MICROTILE_ENABLE (1 << 17) /* GUESS */ +# define R300_DEPTH_ENDIAN_NO_SWAP (0 << 18) /* GUESS */ +# define R300_DEPTH_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */ +# define R300_DEPTH_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */ + +/* BEGIN: Vertex program instruction set */ + +/* Every instruction is four dwords long: + * DWORD 0: output and opcode + * DWORD 1: first argument + * DWORD 2: second argument + * DWORD 3: third argument + * + * Notes: + * - ABS r, a is implemented as MAX r, a, -a + * - MOV is implemented as ADD to zero + * - XPD is implemented as MUL + MAD + * - FLR is implemented as FRC + ADD + * - apparently, fglrx tries to schedule instructions so that there is at + * least one instruction between the write to a temporary and the first + * read from said temporary; however, violations of this scheduling are + * allowed + * - register indices seem to be unrelated with OpenGL aliasing to + * conventional state + * - only one attribute and one parameter can be loaded at a time; however, + * the same attribute/parameter can be used for more than one argument + * - the second software argument for POW is the third hardware argument + * (no idea why) + * - MAD with only temporaries as input seems to use VPI_OUT_SELECT_MAD_2 + * + * There is some magic surrounding LIT: + * The single argument is replicated across all three inputs, but swizzled: + * First argument: xyzy + * Second argument: xyzx + * Third argument: xyzw + * Whenever the result is used later in the fragment program, fglrx forces + * x and w to be 1.0 in the input selection; I don't know whether this is + * strictly necessary + */ #define R300_VPI_OUT_OP_DOT (1 << 0) #define R300_VPI_OUT_OP_MUL (2 << 0) #define R300_VPI_OUT_OP_ADD (3 << 0) @@ -1318,26 +1478,33 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_VPI_OUT_OP_MIN (8 << 0) #define R300_VPI_OUT_OP_SGE (9 << 0) #define R300_VPI_OUT_OP_SLT (10 << 0) -#define R300_VPI_OUT_OP_UNK12 (12 << 0) /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, vector(scalar, vector) */ + /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, vector(scalar, vector) */ +#define R300_VPI_OUT_OP_UNK12 (12 << 0) +#define R300_VPI_OUT_OP_ARL (13 << 0) #define R300_VPI_OUT_OP_EXP (65 << 0) #define R300_VPI_OUT_OP_LOG (66 << 0) -#define R300_VPI_OUT_OP_UNK67 (67 << 0) /* Used in fog computations, scalar(scalar) */ + /* Used in fog computations, scalar(scalar) */ +#define R300_VPI_OUT_OP_UNK67 (67 << 0) #define R300_VPI_OUT_OP_LIT (68 << 0) #define R300_VPI_OUT_OP_POW (69 << 0) #define R300_VPI_OUT_OP_RCP (70 << 0) #define R300_VPI_OUT_OP_RSQ (72 << 0) -#define R300_VPI_OUT_OP_UNK73 (73 << 0) /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, scalar(scalar) */ + /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, scalar(scalar) */ +#define R300_VPI_OUT_OP_UNK73 (73 << 0) #define R300_VPI_OUT_OP_EX2 (75 << 0) #define R300_VPI_OUT_OP_LG2 (76 << 0) #define R300_VPI_OUT_OP_MAD_2 (128 << 0) -#define R300_VPI_OUT_OP_UNK129 (129 << 0) /* all temps, vector(scalar, vector, vector) */ + /* all temps, vector(scalar, vector, vector) */ +#define R300_VPI_OUT_OP_UNK129 (129 << 0) #define R300_VPI_OUT_REG_CLASS_TEMPORARY (0 << 8) +#define R300_VPI_OUT_REG_CLASS_ADDR (1 << 8) #define R300_VPI_OUT_REG_CLASS_RESULT (2 << 8) #define R300_VPI_OUT_REG_CLASS_MASK (31 << 8) #define R300_VPI_OUT_REG_INDEX_SHIFT 13 -#define R300_VPI_OUT_REG_INDEX_MASK (31 << 13) /* GUESS based on fglrx native limits */ + /* GUESS based on fglrx native limits */ +#define R300_VPI_OUT_REG_INDEX_MASK (31 << 13) #define R300_VPI_OUT_WRITE_X (1 << 20) #define R300_VPI_OUT_WRITE_Y (1 << 21) @@ -1348,14 +1515,16 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_VPI_IN_REG_CLASS_ATTRIBUTE (1 << 0) #define R300_VPI_IN_REG_CLASS_PARAMETER (2 << 0) #define R300_VPI_IN_REG_CLASS_NONE (9 << 0) -#define R300_VPI_IN_REG_CLASS_MASK (31 << 0) /* GUESS */ +#define R300_VPI_IN_REG_CLASS_MASK (31 << 0) #define R300_VPI_IN_REG_INDEX_SHIFT 5 -#define R300_VPI_IN_REG_INDEX_MASK (255 << 5) /* GUESS based on fglrx native limits */ + /* GUESS based on fglrx native limits */ +#define R300_VPI_IN_REG_INDEX_MASK (255 << 5) /* The R300 can select components from the input register arbitrarily. -// Use the following constants, shifted by the component shift you -// want to select */ + * Use the following constants, shifted by the component shift you + * want to select + */ #define R300_VPI_IN_SELECT_X 0 #define R300_VPI_IN_SELECT_Y 1 #define R300_VPI_IN_SELECT_Z 2 @@ -1373,11 +1542,11 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_VPI_IN_NEG_Y (1 << 26) #define R300_VPI_IN_NEG_Z (1 << 27) #define R300_VPI_IN_NEG_W (1 << 28) -/* END */ +/* END: Vertex program instruction set */ -//BEGIN: Packet 3 commands +/* BEGIN: Packet 3 commands */ -// A primitive emission dword. +/* A primitive emission dword. */ #define R300_PRIM_TYPE_NONE (0 << 0) #define R300_PRIM_TYPE_POINT (1 << 0) #define R300_PRIM_TYPE_LINE (2 << 0) @@ -1389,7 +1558,8 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_PRIM_TYPE_RECT_LIST (8 << 0) #define R300_PRIM_TYPE_3VRT_POINT_LIST (9 << 0) #define R300_PRIM_TYPE_3VRT_LINE_LIST (10 << 0) -#define R300_PRIM_TYPE_POINT_SPRITES (11 << 0) // GUESS (based on r200) + /* GUESS (based on r200) */ +#define R300_PRIM_TYPE_POINT_SPRITES (11 << 0) #define R300_PRIM_TYPE_LINE_LOOP (12 << 0) #define R300_PRIM_TYPE_QUADS (13 << 0) #define R300_PRIM_TYPE_QUAD_STRIP (14 << 0) @@ -1399,37 +1569,58 @@ I am fairly certain that they are correct unless stated otherwise in comments. #define R300_PRIM_WALK_LIST (2 << 4) #define R300_PRIM_WALK_RING (3 << 4) #define R300_PRIM_WALK_MASK (3 << 4) -#define R300_PRIM_COLOR_ORDER_BGRA (0 << 6) // GUESS (based on r200) -#define R300_PRIM_COLOR_ORDER_RGBA (1 << 6) // GUESS + /* GUESS (based on r200) */ +#define R300_PRIM_COLOR_ORDER_BGRA (0 << 6) +#define R300_PRIM_COLOR_ORDER_RGBA (1 << 6) #define R300_PRIM_NUM_VERTICES_SHIFT 16 +#define R300_PRIM_NUM_VERTICES_MASK 0xffff -// Draw a primitive from vertex data in arrays loaded via 3D_LOAD_VBPNTR. -// Two parameter dwords: -// 0. The first parameter appears to be always 0 -// 1. The second parameter is a standard primitive emission dword. +/* Draw a primitive from vertex data in arrays loaded via 3D_LOAD_VBPNTR. + * Two parameter dwords: + * 0. The first parameter appears to be always 0 + * 1. The second parameter is a standard primitive emission dword. + */ #define R300_PACKET3_3D_DRAW_VBUF 0x00002800 -// Specify the full set of vertex arrays as (address, stride). -// The first parameter is the number of vertex arrays specified. -// The rest of the command is a variable length list of blocks, where -// each block is three dwords long and specifies two arrays. -// The first dword of a block is split into two words, the lower significant -// word refers to the first array, the more significant word to the second -// array in the block. -// The low byte of each word contains the size of an array entry in dwords, -// the high byte contains the stride of the array. -// The second dword of a block contains the pointer to the first array, -// the third dword of a block contains the pointer to the second array. -// Note that if the total number of arrays is odd, the third dword of -// the last block is omitted. +/* Specify the full set of vertex arrays as (address, stride). + * The first parameter is the number of vertex arrays specified. + * The rest of the command is a variable length list of blocks, where + * each block is three dwords long and specifies two arrays. + * The first dword of a block is split into two words, the lower significant + * word refers to the first array, the more significant word to the second + * array in the block. + * The low byte of each word contains the size of an array entry in dwords, + * the high byte contains the stride of the array. + * The second dword of a block contains the pointer to the first array, + * the third dword of a block contains the pointer to the second array. + * Note that if the total number of arrays is odd, the third dword of + * the last block is omitted. + */ #define R300_PACKET3_3D_LOAD_VBPNTR 0x00002F00 #define R300_PACKET3_INDX_BUFFER 0x00003300 # define R300_EB_UNK1_SHIFT 24 # define R300_EB_UNK1 (0x80<<24) # define R300_EB_UNK2 0x0810 +#define R300_PACKET3_3D_DRAW_VBUF_2 0x00003400 #define R300_PACKET3_3D_DRAW_INDX_2 0x00003600 -//END +/* END: Packet 3 commands */ + + +/* Color formats for 2d packets + */ +#define R300_CP_COLOR_FORMAT_CI8 2 +#define R300_CP_COLOR_FORMAT_ARGB1555 3 +#define R300_CP_COLOR_FORMAT_RGB565 4 +#define R300_CP_COLOR_FORMAT_ARGB8888 6 +#define R300_CP_COLOR_FORMAT_RGB332 7 +#define R300_CP_COLOR_FORMAT_RGB8 9 +#define R300_CP_COLOR_FORMAT_ARGB4444 15 + +/* + * CP type-3 packets + */ +#define R300_CP_CMD_BITBLT_MULTI 0xC0009B00 -#endif /* _R300_REG_H */ +#endif /* _R300_REG_H */