From: Bartlomiej Zolnierkiewicz Date: Sun, 27 Apr 2008 13:38:29 +0000 (+0200) Subject: cmd640: always auto-tune PIO X-Git-Tag: v2.6.26-rc1~1029^2~21 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=bdffe5d2717c41945d75b488cfaa401d166cb3dd;p=linux-2.6-omap-h63xx.git cmd640: always auto-tune PIO * Default to tuning PIO0 and disabling prefetch prior to probing devices for CONFIG_BLK_DEV_CMD640_ENHANCED=y case. * Always auto-tune PIO. * Remove no longer used retrieve_drive_counts(). Signed-off-by: Bartlomiej Zolnierkiewicz --- diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c index 6e7a6faa480..812027ddaaf 100644 --- a/drivers/ide/pci/cmd640.c +++ b/drivers/ide/pci/cmd640.c @@ -380,6 +380,7 @@ static void cmd640_dump_regs(void) } #endif +#ifndef CONFIG_BLK_DEV_CMD640_ENHANCED /* * Check whether prefetch is on for a drive, * and initialize the unmask flags for safe operation. @@ -400,9 +401,7 @@ static void __init check_prefetch(ide_drive_t *drive, unsigned int index) drive->no_io_32bit = 0; } } - -#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED - +#else /* * Sets prefetch mode for a drive. */ @@ -458,34 +457,6 @@ static inline u8 pack_nibbles(u8 upper, u8 lower) return ((upper & 0x0f) << 4) | (lower & 0x0f); } -/* - * This routine retrieves the initial drive timings from the chipset. - */ -static void __init retrieve_drive_counts(unsigned int index) -{ - u8 b; - - /* - * Get the internal setup timing, and convert to clock count - */ - b = get_cmd640_reg(arttim_regs[index]) & ~0x3f; - switch (b) { - case 0x00: b = 4; break; - case 0x80: b = 3; break; - case 0x40: b = 2; break; - default: b = 5; break; - } - setup_counts[index] = b; - - /* - * Get the active/recovery counts - */ - b = get_cmd640_reg(drwtim_regs[index]); - active_counts[index] = (b >> 4) ? (b >> 4) : 0x10; - recovery_counts[index] = (b & 0x0f) ? (b & 0x0f) : 0x10; -} - - /* * This routine writes the prepared setup/active/recovery counts * for a drive into the cmd640 chipset registers to active them. @@ -683,7 +654,6 @@ static const struct ide_port_info cmd640_port_info __initdata = { .chipset = ide_cmd640, .host_flags = IDE_HFLAG_SERIALIZE | IDE_HFLAG_NO_DMA | - IDE_HFLAG_NO_AUTOTUNE | IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_ABUSE_FAST_DEVSEL, #ifdef CONFIG_BLK_DEV_CMD640_ENHANCED @@ -866,29 +836,16 @@ static int __init cmd640x_init(void) } #ifdef CONFIG_BLK_DEV_CMD640_ENHANCED - if (drive->autotune || ((index > 1) && second_port_toggled)) { - /* - * Reset timing to the slowest speed and turn off - * prefetch. This way, the drive identify code has - * a better chance. - */ - setup_counts [index] = 4; /* max possible */ - active_counts [index] = 16; /* max possible */ - recovery_counts [index] = 16; /* max possible */ - program_drive_counts(drive, index); - set_prefetch_mode(drive, index, 0); - printk("cmd640: drive%d timings/prefetch cleared\n", index); - } else { - /* - * Record timings/prefetch without changing them. - * This preserves any prior BIOS setup. - */ - retrieve_drive_counts (index); - check_prefetch(drive, index); - printk("cmd640: drive%d timings/prefetch(%s) preserved", - index, drive->no_io_32bit ? "off" : "on"); - display_clocks(index); - } + /* + * Reset timing to the slowest speed and turn off prefetch. + * This way, the drive identify code has a better chance. + */ + setup_counts [index] = 4; /* max possible */ + active_counts [index] = 16; /* max possible */ + recovery_counts [index] = 16; /* max possible */ + program_drive_counts(drive, index); + set_prefetch_mode(drive, index, 0); + printk("cmd640: drive%d timings/prefetch cleared\n", index); #else /* * Set the drive unmask flags to match the prefetch setting