From: Florian Fainelli Date: Fri, 2 Mar 2007 21:07:48 +0000 (+0100) Subject: [MIPS] MTX1: add idsel cardbus ressources X-Git-Tag: v2.6.21-rc3~103^2~1 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=baa545fddd752f46ced034bc3d95778649b67c2d;p=linux-2.6-omap-h63xx.git [MIPS] MTX1: add idsel cardbus ressources Adds cardbus ressources for MTX1 boards which have a PCMCIA controller. Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- diff --git a/arch/mips/au1000/mtx-1/board_setup.c b/arch/mips/au1000/mtx-1/board_setup.c index 7a3cf72c51a..7bc5af8917d 100644 --- a/arch/mips/au1000/mtx-1/board_setup.c +++ b/arch/mips/au1000/mtx-1/board_setup.c @@ -43,6 +43,9 @@ #include #include +extern int (*board_pci_idsel)(unsigned int devsel, int assert); +int mtx1_pci_idsel(unsigned int devsel, int assert); + void board_reset (void) { /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */ @@ -72,11 +75,37 @@ void __init board_setup(void) au_writel( 0xFFFFFFFF, SYS_TRIOUTCLR ); au_writel( 0x00000001, SYS_OUTPUTCLR ); // set M66EN (PCI 66MHz) to OFF au_writel( 0x00000008, SYS_OUTPUTSET ); // set PCI CLKRUN# to OFF + au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON au_writel( 0x00000020, SYS_OUTPUTCLR ); // set eth PHY TX_ER to OFF // enable LED and set it to green au_writel( au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR ); au_writel( 0x18000800, GPIO2_OUTPUT ); + board_pci_idsel = mtx1_pci_idsel; + printk("4G Systems MTX-1 Board\n"); } + +int +mtx1_pci_idsel(unsigned int devsel, int assert) +{ +#define MTX_IDSEL_ONLY_0_AND_3 0 +#if MTX_IDSEL_ONLY_0_AND_3 + if (devsel != 0 && devsel != 3) { + printk("*** not 0 or 3\n"); + return 0; + } +#endif + + if (assert && devsel != 0) { + // supress signal to cardbus + au_writel( 0x00000002, SYS_OUTPUTCLR ); // set EXT_IO3 OFF + } + else { + au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON + } + au_sync_udelay(1); + return 1; +} + diff --git a/arch/mips/au1000/mtx-1/irqmap.c b/arch/mips/au1000/mtx-1/irqmap.c index 4693a4eb2b8..a4fa0f227e4 100644 --- a/arch/mips/au1000/mtx-1/irqmap.c +++ b/arch/mips/au1000/mtx-1/irqmap.c @@ -48,7 +48,7 @@ #include char irq_tab_alchemy[][5] __initdata = { - [0] = { -1, INTA, INTB, INTX, INTX}, /* IDSEL 00 - AdapterA-Slot0 (top) */ + [0] = { -1, INTA, INTA, INTX, INTX}, /* IDSEL 00 - AdapterA-Slot0 (top) */ [1] = { -1, INTB, INTA, INTX, INTX}, /* IDSEL 01 - AdapterA-Slot1 (bottom) */ [2] = { -1, INTC, INTD, INTX, INTX}, /* IDSEL 02 - AdapterB-Slot0 (top) */ [3] = { -1, INTD, INTC, INTX, INTX}, /* IDSEL 03 - AdapterB-Slot1 (bottom) */