From: Darrick J. Wong Date: Wed, 12 Nov 2008 21:27:04 +0000 (-0800) Subject: ics932s401: new clock generator chip driver X-Git-Tag: v2.6.28-rc5~33 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=a412ae3fb90ab49072b82c8cfa1e3e60d2b27005;p=linux-2.6-omap-h63xx.git ics932s401: new clock generator chip driver The ics932s401 is a clock generator chip. This driver allows users to read the current clock outputs. Signed-off-by: Darrick J. Wong Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- diff --git a/Documentation/ics932s401 b/Documentation/ics932s401 new file mode 100644 index 00000000000..07a739f406d --- /dev/null +++ b/Documentation/ics932s401 @@ -0,0 +1,31 @@ +Kernel driver ics932s401 +====================== + +Supported chips: + * IDT ICS932S401 + Prefix: 'ics932s401' + Addresses scanned: I2C 0x69 + Datasheet: Publically available at the IDT website + +Author: Darrick J. Wong + +Description +----------- + +This driver implements support for the IDT ICS932S401 chip family. + +This chip has 4 clock outputs--a base clock for the CPU (which is likely +multiplied to get the real CPU clock), a system clock, a PCI clock, a USB +clock, and a reference clock. The driver reports selected and actual +frequency. If spread spectrum mode is enabled, the driver also reports by what +percent the clock signal is being spread, which should be between 0 and -0.5%. +All frequencies are reported in KHz. + +The ICS932S401 monitors all inputs continuously. The driver will not read +the registers more often than once every other second. + +Special Features +---------------- + +The clocks could be reprogrammed to increase system speed. I will not help you +do this, as you risk damaging your system! diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index 4494ad27cbf..dcac7ca7693 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -227,6 +227,16 @@ config HP_WMI To compile this driver as a module, choose M here: the module will be called hp-wmi. +config ICS932S401 + tristate "Integrated Circuits ICS932S401" + depends on I2C && EXPERIMENTAL + help + If you say yes here you get support for the Integrated Circuits + ICS932S401 clock control chips. + + This driver can also be built as a module. If so, the module + will be called ics932s401. + config MSI_LAPTOP tristate "MSI Laptop Extras" depends on X86 diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index 909e2468cdc..bb14633d136 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_ATMEL_PWM) += atmel_pwm.o obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o obj-$(CONFIG_HP_WMI) += hp-wmi.o +obj-$(CONFIG_ICS932S401) += ics932s401.o obj-$(CONFIG_TC1100_WMI) += tc1100-wmi.o obj-$(CONFIG_LKDTM) += lkdtm.o obj-$(CONFIG_TIFM_CORE) += tifm_core.o diff --git a/drivers/misc/ics932s401.c b/drivers/misc/ics932s401.c new file mode 100644 index 00000000000..6e43ab4231a --- /dev/null +++ b/drivers/misc/ics932s401.c @@ -0,0 +1,515 @@ +/* + * A driver for the Integrated Circuits ICS932S401 + * Copyright (C) 2008 IBM + * + * Author: Darrick J. Wong + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +/* Addresses to scan */ +static const unsigned short normal_i2c[] = { 0x69, I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(ics932s401); + +/* ICS932S401 registers */ +#define ICS932S401_REG_CFG2 0x01 +#define ICS932S401_CFG1_SPREAD 0x01 +#define ICS932S401_REG_CFG7 0x06 +#define ICS932S401_FS_MASK 0x07 +#define ICS932S401_REG_VENDOR_REV 0x07 +#define ICS932S401_VENDOR 1 +#define ICS932S401_VENDOR_MASK 0x0F +#define ICS932S401_REV 4 +#define ICS932S401_REV_SHIFT 4 +#define ICS932S401_REG_DEVICE 0x09 +#define ICS932S401_DEVICE 11 +#define ICS932S401_REG_CTRL 0x0A +#define ICS932S401_MN_ENABLED 0x80 +#define ICS932S401_CPU_ALT 0x04 +#define ICS932S401_SRC_ALT 0x08 +#define ICS932S401_REG_CPU_M_CTRL 0x0B +#define ICS932S401_M_MASK 0x3F +#define ICS932S401_REG_CPU_N_CTRL 0x0C +#define ICS932S401_REG_CPU_SPREAD1 0x0D +#define ICS932S401_REG_CPU_SPREAD2 0x0E +#define ICS932S401_SPREAD_MASK 0x7FFF +#define ICS932S401_REG_SRC_M_CTRL 0x0F +#define ICS932S401_REG_SRC_N_CTRL 0x10 +#define ICS932S401_REG_SRC_SPREAD1 0x11 +#define ICS932S401_REG_SRC_SPREAD2 0x12 +#define ICS932S401_REG_CPU_DIVISOR 0x13 +#define ICS932S401_CPU_DIVISOR_SHIFT 4 +#define ICS932S401_REG_PCISRC_DIVISOR 0x14 +#define ICS932S401_SRC_DIVISOR_MASK 0x0F +#define ICS932S401_PCI_DIVISOR_SHIFT 4 + +/* Base clock is 14.318MHz */ +#define BASE_CLOCK 14318 + +#define NUM_REGS 21 +#define NUM_MIRRORED_REGS 15 + +static int regs_to_copy[NUM_MIRRORED_REGS] = { + ICS932S401_REG_CFG2, + ICS932S401_REG_CFG7, + ICS932S401_REG_VENDOR_REV, + ICS932S401_REG_DEVICE, + ICS932S401_REG_CTRL, + ICS932S401_REG_CPU_M_CTRL, + ICS932S401_REG_CPU_N_CTRL, + ICS932S401_REG_CPU_SPREAD1, + ICS932S401_REG_CPU_SPREAD2, + ICS932S401_REG_SRC_M_CTRL, + ICS932S401_REG_SRC_N_CTRL, + ICS932S401_REG_SRC_SPREAD1, + ICS932S401_REG_SRC_SPREAD2, + ICS932S401_REG_CPU_DIVISOR, + ICS932S401_REG_PCISRC_DIVISOR, +}; + +/* How often do we reread sensors values? (In jiffies) */ +#define SENSOR_REFRESH_INTERVAL (2 * HZ) + +/* How often do we reread sensor limit values? (In jiffies) */ +#define LIMIT_REFRESH_INTERVAL (60 * HZ) + +struct ics932s401_data { + struct attribute_group attrs; + struct mutex lock; + char sensors_valid; + unsigned long sensors_last_updated; /* In jiffies */ + + u8 regs[NUM_REGS]; +}; + +static int ics932s401_probe(struct i2c_client *client, + const struct i2c_device_id *id); +static int ics932s401_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info); +static int ics932s401_remove(struct i2c_client *client); + +static const struct i2c_device_id ics932s401_id[] = { + { "ics932s401", ics932s401 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ics932s401_id); + +static struct i2c_driver ics932s401_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "ics932s401", + }, + .probe = ics932s401_probe, + .remove = ics932s401_remove, + .id_table = ics932s401_id, + .detect = ics932s401_detect, + .address_data = &addr_data, +}; + +static struct ics932s401_data *ics932s401_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct ics932s401_data *data = i2c_get_clientdata(client); + unsigned long local_jiffies = jiffies; + int i, temp; + + mutex_lock(&data->lock); + if (time_before(local_jiffies, data->sensors_last_updated + + SENSOR_REFRESH_INTERVAL) + && data->sensors_valid) + goto out; + + /* + * Each register must be read as a word and then right shifted 8 bits. + * Not really sure why this is; setting the "byte count programming" + * register to 1 does not fix this problem. + */ + for (i = 0; i < NUM_MIRRORED_REGS; i++) { + temp = i2c_smbus_read_word_data(client, regs_to_copy[i]); + data->regs[regs_to_copy[i]] = temp >> 8; + } + + data->sensors_last_updated = local_jiffies; + data->sensors_valid = 1; + +out: + mutex_unlock(&data->lock); + return data; +} + +static ssize_t show_spread_enabled(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + + if (data->regs[ICS932S401_REG_CFG2] & ICS932S401_CFG1_SPREAD) + return sprintf(buf, "1\n"); + + return sprintf(buf, "0\n"); +} + +/* bit to cpu khz map */ +static const int fs_speeds[] = { + 266666, + 133333, + 200000, + 166666, + 333333, + 100000, + 400000, + 0, +}; + +/* clock divisor map */ +static const int divisors[] = {2, 3, 5, 15, 4, 6, 10, 30, 8, 12, 20, 60, 16, + 24, 40, 120}; + +/* Calculate CPU frequency from the M/N registers. */ +static int calculate_cpu_freq(struct ics932s401_data *data) +{ + int m, n, freq; + + m = data->regs[ICS932S401_REG_CPU_M_CTRL] & ICS932S401_M_MASK; + n = data->regs[ICS932S401_REG_CPU_N_CTRL]; + + /* Pull in bits 8 & 9 from the M register */ + n |= ((int)data->regs[ICS932S401_REG_CPU_M_CTRL] & 0x80) << 1; + n |= ((int)data->regs[ICS932S401_REG_CPU_M_CTRL] & 0x40) << 3; + + freq = BASE_CLOCK * (n + 8) / (m + 2); + freq /= divisors[data->regs[ICS932S401_REG_CPU_DIVISOR] >> + ICS932S401_CPU_DIVISOR_SHIFT]; + + return freq; +} + +static ssize_t show_cpu_clock(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + + return sprintf(buf, "%d\n", calculate_cpu_freq(data)); +} + +static ssize_t show_cpu_clock_sel(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + int freq; + + if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_MN_ENABLED) + freq = calculate_cpu_freq(data); + else { + /* Freq is neatly wrapped up for us */ + int fid = data->regs[ICS932S401_REG_CFG7] & ICS932S401_FS_MASK; + freq = fs_speeds[fid]; + if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_CPU_ALT) { + switch (freq) { + case 166666: + freq = 160000; + break; + case 333333: + freq = 320000; + break; + } + } + } + + return sprintf(buf, "%d\n", freq); +} + +/* Calculate SRC frequency from the M/N registers. */ +static int calculate_src_freq(struct ics932s401_data *data) +{ + int m, n, freq; + + m = data->regs[ICS932S401_REG_SRC_M_CTRL] & ICS932S401_M_MASK; + n = data->regs[ICS932S401_REG_SRC_N_CTRL]; + + /* Pull in bits 8 & 9 from the M register */ + n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x80) << 1; + n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x40) << 3; + + freq = BASE_CLOCK * (n + 8) / (m + 2); + freq /= divisors[data->regs[ICS932S401_REG_PCISRC_DIVISOR] & + ICS932S401_SRC_DIVISOR_MASK]; + + return freq; +} + +static ssize_t show_src_clock(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + + return sprintf(buf, "%d\n", calculate_src_freq(data)); +} + +static ssize_t show_src_clock_sel(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + int freq; + + if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_MN_ENABLED) + freq = calculate_src_freq(data); + else + /* Freq is neatly wrapped up for us */ + if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_CPU_ALT && + data->regs[ICS932S401_REG_CTRL] & ICS932S401_SRC_ALT) + freq = 96000; + else + freq = 100000; + + return sprintf(buf, "%d\n", freq); +} + +/* Calculate PCI frequency from the SRC M/N registers. */ +static int calculate_pci_freq(struct ics932s401_data *data) +{ + int m, n, freq; + + m = data->regs[ICS932S401_REG_SRC_M_CTRL] & ICS932S401_M_MASK; + n = data->regs[ICS932S401_REG_SRC_N_CTRL]; + + /* Pull in bits 8 & 9 from the M register */ + n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x80) << 1; + n |= ((int)data->regs[ICS932S401_REG_SRC_M_CTRL] & 0x40) << 3; + + freq = BASE_CLOCK * (n + 8) / (m + 2); + freq /= divisors[data->regs[ICS932S401_REG_PCISRC_DIVISOR] >> + ICS932S401_PCI_DIVISOR_SHIFT]; + + return freq; +} + +static ssize_t show_pci_clock(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + + return sprintf(buf, "%d\n", calculate_pci_freq(data)); +} + +static ssize_t show_pci_clock_sel(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + int freq; + + if (data->regs[ICS932S401_REG_CTRL] & ICS932S401_MN_ENABLED) + freq = calculate_pci_freq(data); + else + freq = 33333; + + return sprintf(buf, "%d\n", freq); +} + +static ssize_t show_value(struct device *dev, + struct device_attribute *devattr, + char *buf); + +static ssize_t show_spread(struct device *dev, + struct device_attribute *devattr, + char *buf); + +static DEVICE_ATTR(spread_enabled, S_IRUGO, show_spread_enabled, NULL); +static DEVICE_ATTR(cpu_clock_selection, S_IRUGO, show_cpu_clock_sel, NULL); +static DEVICE_ATTR(cpu_clock, S_IRUGO, show_cpu_clock, NULL); +static DEVICE_ATTR(src_clock_selection, S_IRUGO, show_src_clock_sel, NULL); +static DEVICE_ATTR(src_clock, S_IRUGO, show_src_clock, NULL); +static DEVICE_ATTR(pci_clock_selection, S_IRUGO, show_pci_clock_sel, NULL); +static DEVICE_ATTR(pci_clock, S_IRUGO, show_pci_clock, NULL); +static DEVICE_ATTR(usb_clock, S_IRUGO, show_value, NULL); +static DEVICE_ATTR(ref_clock, S_IRUGO, show_value, NULL); +static DEVICE_ATTR(cpu_spread, S_IRUGO, show_spread, NULL); +static DEVICE_ATTR(src_spread, S_IRUGO, show_spread, NULL); + +static struct attribute *ics932s401_attr[] = +{ + &dev_attr_spread_enabled.attr, + &dev_attr_cpu_clock_selection.attr, + &dev_attr_cpu_clock.attr, + &dev_attr_src_clock_selection.attr, + &dev_attr_src_clock.attr, + &dev_attr_pci_clock_selection.attr, + &dev_attr_pci_clock.attr, + &dev_attr_usb_clock.attr, + &dev_attr_ref_clock.attr, + &dev_attr_cpu_spread.attr, + &dev_attr_src_spread.attr, + NULL +}; + +static ssize_t show_value(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + int x; + + if (devattr == &dev_attr_usb_clock) + x = 48000; + else if (devattr == &dev_attr_ref_clock) + x = BASE_CLOCK; + else + BUG(); + + return sprintf(buf, "%d\n", x); +} + +static ssize_t show_spread(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct ics932s401_data *data = ics932s401_update_device(dev); + int reg; + unsigned long val; + + if (!(data->regs[ICS932S401_REG_CFG2] & ICS932S401_CFG1_SPREAD)) + return sprintf(buf, "0%%\n"); + + if (devattr == &dev_attr_src_spread) + reg = ICS932S401_REG_SRC_SPREAD1; + else if (devattr == &dev_attr_cpu_spread) + reg = ICS932S401_REG_CPU_SPREAD1; + else + BUG(); + + val = data->regs[reg] | (data->regs[reg + 1] << 8); + val &= ICS932S401_SPREAD_MASK; + + /* Scale 0..2^14 to -0.5. */ + val = 500000 * val / 16384; + return sprintf(buf, "-0.%lu%%\n", val); +} + +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int ics932s401_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = client->adapter; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + if (kind <= 0) { + int vendor, device, revision; + + vendor = i2c_smbus_read_word_data(client, + ICS932S401_REG_VENDOR_REV); + vendor >>= 8; + revision = vendor >> ICS932S401_REV_SHIFT; + vendor &= ICS932S401_VENDOR_MASK; + if (vendor != ICS932S401_VENDOR) + return -ENODEV; + + device = i2c_smbus_read_word_data(client, + ICS932S401_REG_DEVICE); + device >>= 8; + if (device != ICS932S401_DEVICE) + return -ENODEV; + + if (revision != ICS932S401_REV) + dev_info(&adapter->dev, "Unknown revision %d\n", + revision); + } else + dev_dbg(&adapter->dev, "detection forced\n"); + + strlcpy(info->type, "ics932s401", I2C_NAME_SIZE); + + return 0; +} + +static int ics932s401_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ics932s401_data *data; + int err; + + data = kzalloc(sizeof(struct ics932s401_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + mutex_init(&data->lock); + + dev_info(&client->dev, "%s chip found\n", client->name); + + /* Register sysfs hooks */ + data->attrs.attrs = ics932s401_attr; + err = sysfs_create_group(&client->dev.kobj, &data->attrs); + if (err) + goto exit_free; + + return 0; + +exit_free: + kfree(data); +exit: + return err; +} + +static int ics932s401_remove(struct i2c_client *client) +{ + struct ics932s401_data *data = i2c_get_clientdata(client); + + sysfs_remove_group(&client->dev.kobj, &data->attrs); + kfree(data); + return 0; +} + +static int __init ics932s401_init(void) +{ + return i2c_add_driver(&ics932s401_driver); +} + +static void __exit ics932s401_exit(void) +{ + i2c_del_driver(&ics932s401_driver); +} + +MODULE_AUTHOR("Darrick J. Wong "); +MODULE_DESCRIPTION("ICS932S401 driver"); +MODULE_LICENSE("GPL"); + +module_init(ics932s401_init); +module_exit(ics932s401_exit); + +/* IBM IntelliStation Z30 */ +MODULE_ALIAS("dmi:bvnIBM:*:rn9228:*"); +MODULE_ALIAS("dmi:bvnIBM:*:rn9232:*"); + +/* IBM x3650/x3550 */ +MODULE_ALIAS("dmi:bvnIBM:*:pnIBMSystemx3650*"); +MODULE_ALIAS("dmi:bvnIBM:*:pnIBMSystemx3550*");