From: Stefan Richter Date: Sat, 24 Jan 2009 18:41:46 +0000 (+0100) Subject: firewire: sbp2: fix payload limit at S1600 and S3200 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=a08e100aece16e33a45b82924ad85f4066c4ed1c;p=linux-2.6-omap-h63xx.git firewire: sbp2: fix payload limit at S1600 and S3200 1394-2008 clause 16.3.4.1 (1394b-2002 clause 16.3.1.1) defines tighter limits than 1394-2008 clause 6.2.2.3 (1394a-2000 clause 6.2.2.3). Our previously too large limit doesn't matter though if the controller reports its max_receive correctly. Signed-off-by: Stefan Richter --- diff --git a/drivers/firewire/fw-sbp2.c b/drivers/firewire/fw-sbp2.c index e88d5067448..ac803843158 100644 --- a/drivers/firewire/fw-sbp2.c +++ b/drivers/firewire/fw-sbp2.c @@ -168,6 +168,7 @@ struct sbp2_target { int address_high; unsigned int workarounds; unsigned int mgt_orb_timeout; + unsigned int max_payload; int dont_block; /* counter for each logical unit */ int blocked; /* ditto */ @@ -1156,6 +1157,15 @@ static int sbp2_probe(struct device *dev) sbp2_init_workarounds(tgt, model, firmware_revision); + /* + * At S100 we can do 512 bytes per packet, at S200 1024 bytes, + * and so on up to 4096 bytes. The SBP-2 max_payload field + * specifies the max payload size as 2 ^ (max_payload + 2), so + * if we set this to max_speed + 7, we get the right value. + */ + tgt->max_payload = min(device->max_speed + 7, 10U); + tgt->max_payload = min(tgt->max_payload, device->card->max_receive - 1); + /* Do the login in a workqueue so we can easily reschedule retries. */ list_for_each_entry(lu, &tgt->lu_list, link) sbp2_queue_work(lu, DIV_ROUND_UP(HZ, 5)); @@ -1434,7 +1444,6 @@ static int sbp2_scsi_queuecommand(struct scsi_cmnd *cmd, scsi_done_fn_t done) struct sbp2_logical_unit *lu = cmd->device->hostdata; struct fw_device *device = fw_device(lu->tgt->unit->device.parent); struct sbp2_command_orb *orb; - unsigned int max_payload; int generation, retval = SCSI_MLQUEUE_HOST_BUSY; /* @@ -1462,17 +1471,9 @@ static int sbp2_scsi_queuecommand(struct scsi_cmnd *cmd, scsi_done_fn_t done) orb->done = done; orb->cmd = cmd; - orb->request.next.high = cpu_to_be32(SBP2_ORB_NULL); - /* - * At speed 100 we can do 512 bytes per packet, at speed 200, - * 1024 bytes per packet etc. The SBP-2 max_payload field - * specifies the max payload size as 2 ^ (max_payload + 2), so - * if we set this to max_speed + 7, we get the right value. - */ - max_payload = min(device->max_speed + 7, - device->card->max_receive - 1); + orb->request.next.high = cpu_to_be32(SBP2_ORB_NULL); orb->request.misc = cpu_to_be32( - COMMAND_ORB_MAX_PAYLOAD(max_payload) | + COMMAND_ORB_MAX_PAYLOAD(lu->tgt->max_payload) | COMMAND_ORB_SPEED(device->max_speed) | COMMAND_ORB_NOTIFY);