From: Yaniv Rosner Date: Wed, 13 Aug 2008 22:56:17 +0000 (-0700) Subject: bnx2x: Pause settings X-Git-Tag: v2.6.27-rc4~103^2~9 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=8c99e7b0436473593a68e740d1032909bc5335a1;p=linux-2.6-omap-h63xx.git bnx2x: Pause settings Pause settings - 1G pause was not working due to missing write to the emac block (TX_MODE_FLOW_EN) - The flow control should use the negotiated result (after autoneg) so we should save both the requested autoneg and the result - The HW credits with flow control at 1G speed were not optimized and caused low throughput - It is recommended to turn off flow control if the MTU is bigger than 5000B due to internal buffers size Signed-off-by: Yaniv Rosner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index 3b63c8ce952..36fa356c74f 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -38,7 +38,6 @@ #define ETH_MAX_JUMBO_PACKET_SIZE 9600 #define MDIO_ACCESS_TIMEOUT 1000 #define BMAC_CONTROL_RX_ENABLE 2 -#define MAX_MTU_SIZE 5000 /***********************************************************/ /* Shortcut definitions */ @@ -298,11 +297,13 @@ static u8 bnx2x_emac_enable(struct link_params *params, EMAC_RX_MODE_FLOW_EN); bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_EXT_PAUSE_EN); + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); if (vars->flow_ctrl & FLOW_CTRL_TX) bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_EXT_PAUSE_EN); + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); } /* KEEP_VLAN_TAG, promiscuous */ @@ -591,9 +592,9 @@ void bnx2x_link_status_update(struct link_params *params, vars->flow_ctrl &= ~FLOW_CTRL_RX; if (vars->phy_flags & PHY_XGXS_FLAG) { - if (params->req_line_speed && - ((params->req_line_speed == SPEED_10) || - (params->req_line_speed == SPEED_100))) { + if (vars->line_speed && + ((vars->line_speed == SPEED_10) || + (vars->line_speed == SPEED_100))) { vars->phy_flags |= PHY_SGMII_FLAG; } else { vars->phy_flags &= ~PHY_SGMII_FLAG; @@ -670,7 +671,6 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, u8 port = params->port; u32 init_crd, crd; u32 count = 1000; - u32 pause = 0; /* disable port */ REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1); @@ -693,33 +693,25 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, return -EINVAL; } - if (flow_ctrl & FLOW_CTRL_RX) - pause = 1; - REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, pause); - if (pause) { + if (flow_ctrl & FLOW_CTRL_RX || + line_speed == SPEED_10 || + line_speed == SPEED_100 || + line_speed == SPEED_1000 || + line_speed == SPEED_2500) { + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1); /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0); /* update init credit */ - init_crd = 778; /* (800-18-4) */ + init_crd = 778; /* (800-18-4) */ } else { u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)/16; - + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0); /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh); /* update init credit */ switch (line_speed) { - case SPEED_10: - case SPEED_100: - case SPEED_1000: - init_crd = thresh + 55 - 22; - break; - - case SPEED_2500: - init_crd = thresh + 138 - 22; - break; - case SPEED_10000: init_crd = thresh + 553 - 22; break; @@ -1114,7 +1106,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); /* CL37 Autoneg Enabled */ - if (params->req_line_speed == SPEED_AUTO_NEG) + if (vars->line_speed == SPEED_AUTO_NEG) reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN; else /* CL37 Autoneg Disabled */ reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | @@ -1132,7 +1124,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN; - if (params->req_line_speed == SPEED_AUTO_NEG) + if (vars->line_speed == SPEED_AUTO_NEG) reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; else reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; @@ -1148,7 +1140,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_REG_BANK_BAM_NEXT_PAGE, MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, ®_val); - if (params->req_line_speed == SPEED_AUTO_NEG) { + if (vars->line_speed == SPEED_AUTO_NEG) { /* Enable BAM aneg Mode and TetonII aneg Mode */ reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); @@ -1164,7 +1156,7 @@ static void bnx2x_set_autoneg(struct link_params *params, reg_val); /* Enable Clause 73 Aneg */ - if ((params->req_line_speed == SPEED_AUTO_NEG) && + if ((vars->line_speed == SPEED_AUTO_NEG) && (SUPPORT_CL73)) { /* Enable BAM Station Manager */ @@ -1226,7 +1218,8 @@ static void bnx2x_set_autoneg(struct link_params *params, } /* program SerDes, forced speed */ -static void bnx2x_program_serdes(struct link_params *params) +static void bnx2x_program_serdes(struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 reg_val; @@ -1248,28 +1241,35 @@ static void bnx2x_program_serdes(struct link_params *params) /* program speed - needed only if the speed is greater than 1G (2.5G or 10G) */ - if (!((params->req_line_speed == SPEED_1000) || - (params->req_line_speed == SPEED_100) || - (params->req_line_speed == SPEED_10))) { - CL45_RD_OVER_CL22(bp, params->port, + CL45_RD_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_MISC1, ®_val); - /* clearing the speed value before setting the right speed */ - reg_val &= ~MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK; + /* clearing the speed value before setting the right speed */ + DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val); + + reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK | + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); + + if (!((vars->line_speed == SPEED_1000) || + (vars->line_speed == SPEED_100) || + (vars->line_speed == SPEED_10))) { + reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M | MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); - if (params->req_line_speed == SPEED_10000) + if (vars->line_speed == SPEED_10000) reg_val |= MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4; - if (params->req_line_speed == SPEED_13000) + if (vars->line_speed == SPEED_13000) reg_val |= MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G; - CL45_WR_OVER_CL22(bp, params->port, + } + + CL45_WR_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_MISC1, reg_val); - } + } static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) @@ -1295,48 +1295,49 @@ static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) MDIO_OVER_1G_UP3, 0); } -static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, - u32 *ieee_fc) +static void bnx2x_calc_ieee_aneg_adv(struct link_params *params, u32 *ieee_fc) { - struct bnx2x *bp = params->bp; - /* for AN, we are always publishing full duplex */ - u16 an_adv = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; - + *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; /* resolve pause mode and advertisement * Please refer to Table 28B-3 of the 802.3ab-1999 spec */ switch (params->req_flow_ctrl) { case FLOW_CTRL_AUTO: - if (params->mtu <= MAX_MTU_SIZE) { - an_adv |= + if (params->req_fc_auto_adv == FLOW_CTRL_BOTH) { + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; } else { - an_adv |= + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; } break; case FLOW_CTRL_TX: - an_adv |= + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; break; case FLOW_CTRL_RX: case FLOW_CTRL_BOTH: - an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; break; case FLOW_CTRL_NONE: default: - an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; break; } +} - *ieee_fc = an_adv; +static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, + u32 ieee_fc) +{ + struct bnx2x *bp = params->bp; + /* for AN, we are always publishing full duplex */ CL45_WR_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_AUTO_NEG_ADV, an_adv); + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, (u16)ieee_fc); } static void bnx2x_restart_autoneg(struct link_params *params) @@ -1382,7 +1383,8 @@ static void bnx2x_restart_autoneg(struct link_params *params) } } -static void bnx2x_initialize_sgmii_process(struct link_params *params) +static void bnx2x_initialize_sgmii_process(struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 control1; @@ -1406,7 +1408,7 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) control1); /* if forced speed */ - if (!(params->req_line_speed == SPEED_AUTO_NEG)) { + if (!(vars->line_speed == SPEED_AUTO_NEG)) { /* set speed, disable autoneg */ u16 mii_control; @@ -1419,7 +1421,7 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK| MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX); - switch (params->req_line_speed) { + switch (vars->line_speed) { case SPEED_100: mii_control |= MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100; @@ -1433,8 +1435,8 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) break; default: /* invalid speed for SGMII */ - DP(NETIF_MSG_LINK, "Invalid req_line_speed 0x%x\n", - params->req_line_speed); + DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", + vars->line_speed); break; } @@ -1460,20 +1462,20 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) */ static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result) -{ - switch (pause_result) { /* ASYM P ASYM P */ - case 0xb: /* 1 0 1 1 */ +{ /* LD LP */ + switch (pause_result) { /* ASYM P ASYM P */ + case 0xb: /* 1 0 1 1 */ vars->flow_ctrl = FLOW_CTRL_TX; break; - case 0xe: /* 1 1 1 0 */ + case 0xe: /* 1 1 1 0 */ vars->flow_ctrl = FLOW_CTRL_RX; break; - case 0x5: /* 0 1 0 1 */ - case 0x7: /* 0 1 1 1 */ - case 0xd: /* 1 1 0 1 */ - case 0xf: /* 1 1 1 1 */ + case 0x5: /* 0 1 0 1 */ + case 0x7: /* 0 1 1 1 */ + case 0xd: /* 1 1 0 1 */ + case 0xf: /* 1 1 1 1 */ vars->flow_ctrl = FLOW_CTRL_BOTH; break; @@ -1487,8 +1489,8 @@ static u8 bnx2x_ext_phy_resove_fc(struct link_params *params, { struct bnx2x *bp = params->bp; u8 ext_phy_addr; - u16 ld_pause; /* local */ - u16 lp_pause; /* link partner */ + u16 ld_pause; /* local */ + u16 lp_pause; /* link partner */ u16 an_complete; /* AN complete */ u16 pause_result; u8 ret = 0; @@ -1531,6 +1533,28 @@ static u8 bnx2x_ext_phy_resove_fc(struct link_params *params, DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x \n", pause_result); bnx2x_pause_resolve(vars, pause_result); + if (vars->flow_ctrl == FLOW_CTRL_NONE && + ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &ld_pause); + + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LP, &lp_pause); + pause_result = (ld_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5; + pause_result |= (lp_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7; + + bnx2x_pause_resolve(vars, pause_result); + DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x \n", + pause_result); + } } return ret; } @@ -1573,13 +1597,10 @@ static void bnx2x_flow_ctrl_resolve(struct link_params *params, (bnx2x_ext_phy_resove_fc(params, vars))) { return; } else { - vars->flow_ctrl = params->req_flow_ctrl; - if (vars->flow_ctrl == FLOW_CTRL_AUTO) { - if (params->mtu <= MAX_MTU_SIZE) - vars->flow_ctrl = FLOW_CTRL_BOTH; - else - vars->flow_ctrl = FLOW_CTRL_TX; - } + if (params->req_flow_ctrl == FLOW_CTRL_AUTO) + vars->flow_ctrl = params->req_fc_auto_adv; + else + vars->flow_ctrl = params->req_flow_ctrl; } DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl); } @@ -1709,12 +1730,12 @@ static u8 bnx2x_link_settings_status(struct link_params *params, } if (vars->flow_ctrl & FLOW_CTRL_TX) - vars->link_status |= - LINK_STATUS_TX_FLOW_CONTROL_ENABLED; + vars->link_status |= + LINK_STATUS_TX_FLOW_CONTROL_ENABLED; if (vars->flow_ctrl & FLOW_CTRL_RX) - vars->link_status |= - LINK_STATUS_RX_FLOW_CONTROL_ENABLED; + vars->link_status |= + LINK_STATUS_RX_FLOW_CONTROL_ENABLED; } else { /* link_down */ DP(NETIF_MSG_LINK, "phy link down\n"); @@ -2286,13 +2307,16 @@ static void bnx2x_ext_phy_set_pause(struct link_params *params, MDIO_AN_REG_ADV_PAUSE, &val); val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH; + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ - if (vars->ieee_fc & + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; } - if (vars->ieee_fc & + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { val |= MDIO_AN_REG_ADV_PAUSE_PAUSE; @@ -2339,7 +2363,7 @@ static void bnx2x_init_internal_phy(struct link_params *params, bnx2x_set_autoneg(params, vars); /* program speed and duplex */ - bnx2x_program_serdes(params); + bnx2x_program_serdes(params, vars); } else { /* AN_mode */ DP(NETIF_MSG_LINK, "not SGMII, AN\n"); @@ -2349,7 +2373,7 @@ static void bnx2x_init_internal_phy(struct link_params *params, /* program duplex & pause advertisement (for aneg) */ bnx2x_set_ieee_aneg_advertisment(params, - &vars->ieee_fc); + vars->ieee_fc); /* enable autoneg */ bnx2x_set_autoneg(params, vars); @@ -2361,7 +2385,7 @@ static void bnx2x_init_internal_phy(struct link_params *params, } else { /* SGMII mode */ DP(NETIF_MSG_LINK, "SGMII\n"); - bnx2x_initialize_sgmii_process(params); + bnx2x_initialize_sgmii_process(params, vars); } } @@ -2481,7 +2505,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FD, + MDIO_AN_REG_CL37_FC_LP, 0x0020); /* Enable CL37 AN */ bnx2x_cl45_write(bp, params->port, @@ -2657,13 +2681,13 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_CL73, 0x040c); + MDIO_AN_REG_CL37_FC_LD, 0x040c); /* Add support for CL37 (passive mode) II */ bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FD, 0x20); + MDIO_AN_REG_CL37_FC_LD, 0x20); /* Add support for CL37 (passive mode) III */ bnx2x_cl45_write(bp, params->port, ext_phy_type, @@ -2785,7 +2809,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; u32 ext_phy_type; @@ -2826,6 +2850,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_REG_RX_SD, &rx_sd); DP(NETIF_MSG_LINK, "8705 rx_sd 0x%x\n", rx_sd); ext_phy_link_up = (rx_sd & 0x1); + if (ext_phy_link_up) + vars->line_speed = SPEED_10000; break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: @@ -3734,7 +3760,7 @@ static u8 bnx2x_link_initialize(struct link_params *params, req_line_speed*/ vars->line_speed = params->req_line_speed; - bnx2x_set_ieee_aneg_advertisment(params, &vars->ieee_fc); + bnx2x_calc_ieee_aneg_adv(params, &vars->ieee_fc); /* init ext phy and enable link state int */ non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || diff --git a/drivers/net/bnx2x_link.h b/drivers/net/bnx2x_link.h index 714d37ac95d..b222552b868 100644 --- a/drivers/net/bnx2x_link.h +++ b/drivers/net/bnx2x_link.h @@ -58,11 +58,13 @@ struct link_params { u16 req_duplex; u16 req_flow_ctrl; + u16 req_fc_auto_adv; /* Should be set to TX / BOTH when + req_flow_ctrl is set to AUTO */ u16 req_line_speed; /* Also determine AutoNeg */ /* Device parameters */ u8 mac_addr[6]; - u16 mtu; + /* shmem parameters */ diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index d29f22763fe..a37549b5bc1 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1946,7 +1946,14 @@ static u8 bnx2x_initial_phy_init(struct bnx2x *bp) u8 rc; /* Initialize link parameters structure variables */ - bp->link_params.mtu = bp->dev->mtu; + /* It is recommended to turn off RX FC for jumbo frames + for better performance */ + if (IS_E1HMF(bp)) + bp->link_params.req_fc_auto_adv = FLOW_CTRL_BOTH; + else if (bp->dev->mtu > 5000) + bp->link_params.req_fc_auto_adv = FLOW_CTRL_TX; + else + bp->link_params.req_fc_auto_adv = FLOW_CTRL_BOTH; bnx2x_acquire_phy_lock(bp); rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 58fbeb1cf78..5029d1e466f 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -4966,6 +4966,7 @@ #define EMAC_RX_MODE_PROMISCUOUS (1L<<8) #define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31) #define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3) +#define EMAC_TX_MODE_FLOW_EN (1L<<4) #define MISC_REGISTERS_GPIO_0 0 #define MISC_REGISTERS_GPIO_1 1 #define MISC_REGISTERS_GPIO_2 2 @@ -5615,7 +5616,8 @@ Theotherbitsarereservedandshouldbezero*/ #define MDIO_AN_REG_LINK_STATUS 0x8304 #define MDIO_AN_REG_CL37_CL73 0x8370 #define MDIO_AN_REG_CL37_AN 0xffe0 -#define MDIO_AN_REG_CL37_FD 0xffe4 +#define MDIO_AN_REG_CL37_FC_LD 0xffe4 +#define MDIO_AN_REG_CL37_FC_LP 0xffe5 #define IGU_FUNC_BASE 0x0400