From: Mauro Carvalho Chehab Date: Wed, 30 Aug 2006 01:07:03 +0000 (-0300) Subject: V4L/DVB (4553): Add support for saa7111 and partial support for saa7118 X-Git-Tag: v2.6.19-rc1~643^2~46 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=89f75ffc7e97d96ea76556671446d57d77c46beb;p=linux-2.6-omap-h63xx.git V4L/DVB (4553): Add support for saa7111 and partial support for saa7118 Signed-off-by: Mauro Carvalho Chehab --- diff --git a/drivers/media/video/saa7115.c b/drivers/media/video/saa7115.c index d5052dbd074..900c65772fa 100644 --- a/drivers/media/video/saa7115.c +++ b/drivers/media/video/saa7115.c @@ -1,4 +1,6 @@ -/* saa7115 - Philips SAA7113/SAA7114/SAA7115 video decoder driver +/* saa711x - Philips SAA711x video decoder driver + * This driver can work with saa7111, saa7111a, saa7113, saa7114, + * saa7115 and saa7118. * * Based on saa7114 driver by Maxim Yevtyushkin, which is based on * the saa7111 driver by Dave Perks. @@ -16,7 +18,9 @@ * (2/17/2003) * * VBI support (2004) and cleanups (2005) by Hans Verkuil - * SAA7113 support by Mauro Carvalho Chehab + * + * Copyright (c) 2005-2006 Mauro Carvalho Chehab + * SAA7111, SAA7113 and SAA7118 support * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -44,7 +48,7 @@ #include #include -MODULE_DESCRIPTION("Philips SAA7113/SAA7114/SAA7115 video decoder driver"); +MODULE_DESCRIPTION("Philips SAA7111/SAA7113/SAA7114/SAA7115/SAA7118 video decoder driver"); MODULE_AUTHOR( "Maxim Yevtyushkin, Kevin Thayer, Chris Kennedy, " "Hans Verkuil, Mauro Carvalho Chehab"); MODULE_LICENSE("GPL"); @@ -55,8 +59,8 @@ module_param(debug, bool, 0644); MODULE_PARM_DESC(debug, "Debug level (0-1)"); static unsigned short normal_i2c[] = { - 0x4a >> 1, 0x48 >> 1, /* SAA7113 */ - 0x42 >> 1, 0x40 >> 1, /* SAA7114 and SAA7115 */ + 0x4a >> 1, 0x48 >> 1, /* SAA7111, SAA7111A and SAA7113 */ + 0x42 >> 1, 0x40 >> 1, /* SAA7114, SAA7115 and SAA7118 */ I2C_CLIENT_END }; @@ -86,15 +90,58 @@ static inline int saa7115_write(struct i2c_client *client, u8 reg, u8 value) return i2c_smbus_write_byte_data(client, reg, value); } +/* Sanity routine to check if a register is present */ +static int saa711x_has_reg(const int id, const u8 reg) +{ + switch (id) { + case V4L2_IDENT_SAA7111: + if (reg>0x1f || reg==1 || reg==0x0f || reg==0x14 || reg==0x18 + || reg==0x19 || reg==0x1d || reg==0x1e) + return 0; + case V4L2_IDENT_SAA7113: + if (reg>0x62 || reg==0x14 || (reg>=0x18 && reg<=0x1e) || + (reg>=0x20 && reg<=0x3f) ||reg==0x5f ) + return 0; + case V4L2_IDENT_SAA7114: + if (reg>=0xf0 || (reg>=0x1a && reg<=0x1e) || + (reg>=0x20 && reg<=0x2f) || + (reg>=0x63 && reg<=0x7f) ) + return 0; + case V4L2_IDENT_SAA7115: + if ((reg>=0x20 && reg<=0x2f) || (reg==0x5c) || + (reg>=0xfc && reg<=0xfe) ) + return 0; + case V4L2_IDENT_SAA7118: + if (reg>=0xf0 || (reg>=0x1a && reg<=0x1d) || + (reg>=0x63 && reg<=0x6f) ) + return 0; + } + + /* Those registers are reserved for all family */ + if (unlikely((reg>=0x20 && reg<=0x22) || + (reg>=0x26 && reg<=0x28) || + (reg>=0x3b && reg<=0x3f) || (reg==0x5f) || + (reg>=0x63 && reg<=0x6f) ) ) + return 0; + + return 1; +} + static int saa7115_writeregs(struct i2c_client *client, const unsigned char *regs) { + struct saa7115_state *state = i2c_get_clientdata(client); unsigned char reg, data; while (*regs != 0x00) { reg = *(regs++); data = *(regs++); - if (saa7115_write(client, reg, data) < 0) - return -1; + + /* According with datasheets, reserved regs should be + filled with 0 - seems better not to touch on they */ + if (saa711x_has_reg(state->ident,reg)) { + if (saa7115_write(client, reg, data) < 0) + return -1; + } } return 0; } @@ -106,10 +153,80 @@ static inline int saa7115_read(struct i2c_client *client, u8 reg) /* ----------------------------------------------------------------------- */ +/* SAA7111 initialization table */ +static const unsigned char saa7111_init_auto_input[] = { + R_01_INC_DELAY, 0x00, /* reserved */ + + /*front end */ + R_02_INPUT_CNTL_1, 0xd0, /* FUSE=3, GUDL=2, MODE=0 */ + R_03_INPUT_CNTL_2, 0x23, /* HLNRS=0, VBSL=1, WPOFF=0, HOLDG=0, + * GAFIX=0, GAI1=256, GAI2=256 */ + R_04_INPUT_CNTL_3, 0x00, /* GAI1=256 */ + R_05_INPUT_CNTL_4, 0x00, /* GAI2=256 */ + + /* decoder */ + R_06_H_SYNC_START, 0xf3, /* HSB at 13(50Hz) / 17(60Hz) + * pixels after end of last line */ + R_07_H_SYNC_STOP, 0xe8, /* HSS seems to be needed to + * work with NTSC, too */ + R_08_SYNC_CNTL, 0xc8, /* AUFD=1, FSEL=1, EXFIL=0, + * VTRC=1, HPLL=0, VNOI=0 */ + R_09_LUMA_CNTL, 0x01, /* BYPS=0, PREF=0, BPSS=0, + * VBLB=0, UPTCV=0, APER=1 */ + R_0A_LUMA_BRIGHT_CNTL, 0x80, + R_0B_LUMA_CONTRAST_CNTL, 0x47, /* 0b - CONT=1.109 */ + R_0C_CHROMA_SAT_CNTL, 0x40, + R_0D_CHROMA_HUE_CNTL, 0x00, + R_0E_CHROMA_CNTL_1, 0x01, /* 0e - CDTO=0, CSTD=0, DCCF=0, + * FCTC=0, CHBW=1 */ + R_0F_CHROMA_GAIN_CNTL, 0x00, /* reserved */ + R_10_CHROMA_CNTL_2, 0x48, /* 10 - OFTS=1, HDEL=0, VRLN=1, YDEL=0 */ + R_11_MODE_DELAY_CNTL, 0x1c, /* 11 - GPSW=0, CM99=0, FECO=0, COMPO=1, + * OEYC=1, OEHV=1, VIPB=0, COLO=0 */ + R_12_RT_SIGNAL_CNTL, 0x00, /* 12 - output control 2 */ + R_13_RT_X_PORT_OUT_CNTL, 0x00, /* 13 - output control 3 */ + R_14_ANAL_ADC_COMPAT_CNTL, 0x00, + R_15_VGATE_START_FID_CHG, 0x00, + R_16_VGATE_STOP, 0x00, + R_17_MISC_VGATE_CONF_AND_MSB, 0x00, + + 0x00, 0x00 +}; + +/* SAA7113 init codes */ +static const unsigned char saa7113_init_auto_input[] = { + R_01_INC_DELAY, 0x08, + R_02_INPUT_CNTL_1, 0xc2, + R_03_INPUT_CNTL_2, 0x30, + R_04_INPUT_CNTL_3, 0x00, + R_05_INPUT_CNTL_4, 0x00, + R_06_H_SYNC_START, 0x89, + R_07_H_SYNC_STOP, 0x0d, + R_08_SYNC_CNTL, 0x88, + R_09_LUMA_CNTL, 0x01, + R_0A_LUMA_BRIGHT_CNTL, 0x80, + R_0B_LUMA_CONTRAST_CNTL, 0x47, + R_0C_CHROMA_SAT_CNTL, 0x40, + R_0D_CHROMA_HUE_CNTL, 0x00, + R_0E_CHROMA_CNTL_1, 0x01, + R_0F_CHROMA_GAIN_CNTL, 0x2a, + R_10_CHROMA_CNTL_2, 0x08, + R_11_MODE_DELAY_CNTL, 0x0c, + R_12_RT_SIGNAL_CNTL, 0x07, + R_13_RT_X_PORT_OUT_CNTL, 0x00, + R_14_ANAL_ADC_COMPAT_CNTL, 0x00, + R_15_VGATE_START_FID_CHG, 0x00, + R_16_VGATE_STOP, 0x00, + R_17_MISC_VGATE_CONF_AND_MSB, 0x00, + + 0x00, 0x00 +}; + /* If a value differs from the Hauppauge driver values, then the comment starts with 'was 0xXX' to denote the Hauppauge value. Otherwise the value is identical to what the Hauppauge driver sets. */ +/* SAA7114 and SAA7115 initialization table */ static const unsigned char saa7115_init_auto_input[] = { /* Front-End Part */ R_01_INC_DELAY, 0x48, /* white peak control disabled */ @@ -142,6 +259,7 @@ static const unsigned char saa7115_init_auto_input[] = { 0x00, 0x00 }; +/* Used to reset saa7113, saa7114 and saa7115 */ static const unsigned char saa7115_cfg_reset_scaler[] = { R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x00, /* disable I-port output */ R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0, /* reset scaler */ @@ -152,6 +270,7 @@ static const unsigned char saa7115_cfg_reset_scaler[] = { /* ============== SAA7715 VIDEO templates ============= */ +/* Used on saa7114 and saa7115 */ static const unsigned char saa7115_cfg_60hz_fullres_x[] = { /* hsize = 0x2d0 = 720 */ R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH, 0xd0, @@ -170,6 +289,7 @@ static const unsigned char saa7115_cfg_60hz_fullres_x[] = { 0x00, 0x00 }; +/* Used on saa7114 and saa7115 */ static const unsigned char saa7115_cfg_60hz_fullres_y[] = { /* output window size = 248 (but 60hz is 240?) */ R_CE_B_VERT_OUTPUT_WINDOW_LENGTH, 0xf8, @@ -408,33 +528,6 @@ static const unsigned char saa7115_cfg_vbi_off[] = { 0x00, 0x00 }; -static const unsigned char saa7113_init_auto_input[] = { - R_01_INC_DELAY, 0x08, - R_02_INPUT_CNTL_1, 0xc2, - R_03_INPUT_CNTL_2, 0x30, - R_04_INPUT_CNTL_3, 0x00, - R_05_INPUT_CNTL_4, 0x00, - R_06_H_SYNC_START, 0x89, - R_07_H_SYNC_STOP, 0x0d, - R_08_SYNC_CNTL, 0x88, - R_09_LUMA_CNTL, 0x01, - R_0A_LUMA_BRIGHT_CNTL, 0x80, - R_0B_LUMA_CONTRAST_CNTL, 0x47, - R_0C_CHROMA_SAT_CNTL, 0x40, - R_0D_CHROMA_HUE_CNTL, 0x00, - R_0E_CHROMA_CNTL_1, 0x01, - R_0F_CHROMA_GAIN_CNTL, 0x2a, - R_10_CHROMA_CNTL_2, 0x08, - R_11_MODE_DELAY_CNTL, 0x0c, - R_12_RT_SIGNAL_CNTL, 0x07, - R_13_RT_X_PORT_OUT_CNTL, 0x00, - R_14_ANAL_ADC_COMPAT_CNTL, 0x00, - R_15_VGATE_START_FID_CHG, 0x00, - R_16_VGATE_STOP, 0x00, - R_17_MISC_VGATE_CONF_AND_MSB, 0x00, - - 0x00, 0x00 -}; static const unsigned char saa7115_init_misc[] = { R_81_V_SYNC_FLD_ID_SRC_SEL_AND_RETIMED_V_F, 0x01, @@ -662,7 +755,6 @@ static int saa7115_decode_wss(u8 * p) return wss; } - static int saa7115_set_audio_clock_freq(struct i2c_client *client, u32 freq) { struct saa7115_state *state = i2c_get_clientdata(client); @@ -672,16 +764,16 @@ static int saa7115_set_audio_clock_freq(struct i2c_client *client, u32 freq) u64 f; u8 acc = 0; /* reg 0x3a, audio clock control */ + /* Checks for chips that don't have audio clock (saa7111, saa7113) */ + if (!saa711x_has_reg(state->ident,R_30_AUD_MAST_CLK_CYCLES_PER_FIELD)) + return 0; + v4l_dbg(1, debug, client, "set audio clock freq: %d\n", freq); /* sanity check */ if (freq < 32000 || freq > 48000) return -EINVAL; - /* The saa7113 has no audio clock */ - if (state->ident == V4L2_IDENT_SAA7113) - return 0; - /* hz is the refresh rate times 100 */ hz = (state->std & V4L2_STD_525_60) ? 5994 : 5000; /* acpf = (256 * freq) / field_frequency == (256 * 100 * freq) / hz */ @@ -799,7 +891,6 @@ static int saa7115_get_v4lctrl(struct i2c_client *client, struct v4l2_control *c static void saa7115_set_v4lstd(struct i2c_client *client, v4l2_std_id std) { struct saa7115_state *state = i2c_get_clientdata(client); - int taskb = saa7115_read(client, R_80_GLOBAL_CNTL_1) & 0x10; /* Prevent unnecessary standard changes. During a standard change the I-Port is temporarily disabled. Any devices @@ -821,7 +912,7 @@ static void saa7115_set_v4lstd(struct i2c_client *client, v4l2_std_id std) } /* Register 0E - Bits D6-D4 on NO-AUTO mode - (SAA7113 doesn't have auto mode) + (SAA7111 and SAA7113 doesn't have auto mode) 50 Hz / 625 lines 60 Hz / 525 lines 000 PAL BGDHI (4.43Mhz) NTSC M (3.58MHz) 001 NTSC 4.43 (50 Hz) PAL 4.43 (60 Hz) @@ -829,7 +920,8 @@ static void saa7115_set_v4lstd(struct i2c_client *client, v4l2_std_id std) 011 NTSC N (3.58MHz) PAL M (3.58MHz) 100 reserved NTSC-Japan (3.58MHz) */ - if (state->ident == V4L2_IDENT_SAA7113) { + if (state->ident == V4L2_IDENT_SAA7111 || + state->ident == V4L2_IDENT_SAA7113) { u8 reg = saa7115_read(client, R_0E_CHROMA_CNTL_1) & 0x8f; if (std == V4L2_STD_PAL_M) { @@ -842,18 +934,19 @@ static void saa7115_set_v4lstd(struct i2c_client *client, v4l2_std_id std) reg |= 0x40; } saa7115_write(client, R_0E_CHROMA_CNTL_1, reg); - } - + } else { + /* restart task B if needed */ + int taskb = saa7115_read(client, R_80_GLOBAL_CNTL_1) & 0x10; - state->std = std; + if (taskb && state->ident == V4L2_IDENT_SAA7114) { + saa7115_writeregs(client, saa7115_cfg_vbi_on); + } - /* restart task B if needed */ - if (taskb && state->ident != V4L2_IDENT_SAA7115) { - saa7115_writeregs(client, saa7115_cfg_vbi_on); + /* switch audio mode too! */ + saa7115_set_audio_clock_freq(client, state->audclk_freq); } - /* switch audio mode too! */ - saa7115_set_audio_clock_freq(client, state->audclk_freq); + state->std = std; } static v4l2_std_id saa7115_get_v4lstd(struct i2c_client *client) @@ -919,9 +1012,16 @@ static void saa7115_set_lcr(struct i2c_client *client, struct v4l2_sliced_vbi_fo u8 lcr[24]; int i, x; - /* saa7113/7114 doesn't yet support VBI */ +#if 1 + /* saa7113/7114/7118 VBI support are experimental */ + if (!saa711x_has_reg(state->ident,R_41_LCR_BASE)) + return; + +#else + /* SAA7113 and SAA7118 also should support VBI - Need testing */ if (state->ident != V4L2_IDENT_SAA7115) return; +#endif for (i = 0; i <= 23; i++) lcr[i] = 0xff; @@ -1021,8 +1121,9 @@ static int saa7115_set_v4lfmt(struct i2c_client *client, struct v4l2_format *fmt struct saa7115_state *state = i2c_get_clientdata(client); struct v4l2_pix_format *pix; int HPSC, HFSC; - int VSCY, Vsrc; + int VSCY; int is_50hz = state->std & V4L2_STD_625_50; + int Vsrc = is_50hz ? 576 : 480; if (fmt->type == V4L2_BUF_TYPE_SLICED_VBI_CAPTURE) { saa7115_set_lcr(client, &fmt->fmt.sliced); @@ -1041,18 +1142,29 @@ static int saa7115_set_v4lfmt(struct i2c_client *client, struct v4l2_format *fmt if ((pix->height < 1) || (pix->height > 960)) return -EINVAL; + if (!saa711x_has_reg(state->ident,R_D0_B_HORIZ_PRESCALING)) { + /* Decoder only supports 720 columns and 480 or 576 lines */ + if (pix->width != 720) + return -EINVAL; + if (pix->height != Vsrc) + return -EINVAL; + } + /* probably have a valid size, let's set it */ /* Set output width/height */ /* width */ - saa7115_write(client, R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH, - (u8) (pix->width & 0xff)); - saa7115_write(client, R_CD_B_HORIZ_OUTPUT_WINDOW_LENGTH_MSB, - (u8) ((pix->width >> 8) & 0xff)); - /* height */ - saa7115_write(client, R_CE_B_VERT_OUTPUT_WINDOW_LENGTH, - (u8) (pix->height & 0xff)); - saa7115_write(client, R_CF_B_VERT_OUTPUT_WINDOW_LENGTH_MSB, - (u8) ((pix->height >> 8) & 0xff)); + + if (!saa711x_has_reg(state->ident,R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH)) { + saa7115_write(client, R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH, + (u8) (pix->width & 0xff)); + saa7115_write(client, R_CD_B_HORIZ_OUTPUT_WINDOW_LENGTH_MSB, + (u8) ((pix->width >> 8) & 0xff)); + /* height */ + saa7115_write(client, R_CE_B_VERT_OUTPUT_WINDOW_LENGTH, + (u8) (pix->height & 0xff)); + saa7115_write(client, R_CF_B_VERT_OUTPUT_WINDOW_LENGTH_MSB, + (u8) ((pix->height >> 8) & 0xff)); + } /* Scaling settings */ /* Hprescaler is floor(inres/outres) */ @@ -1090,8 +1202,6 @@ static int saa7115_set_v4lfmt(struct i2c_client *client, struct v4l2_format *fmt } } - Vsrc = is_50hz ? 576 : 480; - if (pix->height != Vsrc) { VSCY = (int)((1024 * Vsrc) / pix->height); v4l_dbg(1, debug, client, "Vsrc: %d, Vscy: 0x%05x\n", Vsrc, VSCY); @@ -1123,6 +1233,7 @@ static int saa7115_set_v4lfmt(struct i2c_client *client, struct v4l2_format *fmt } saa7115_writeregs(client, saa7115_cfg_reset_scaler); + return 0; } @@ -1468,15 +1579,25 @@ static int saa7115_attach(struct i2c_adapter *adapter, int address, int kind) state->hue = 0; state->sat = 64; switch (chip_id) { + case 1: + state->ident = V4L2_IDENT_SAA7111; + break; case 3: state->ident = V4L2_IDENT_SAA7113; break; case 4: state->ident = V4L2_IDENT_SAA7114; break; - default: + case 5: state->ident = V4L2_IDENT_SAA7115; break; + case 8: + state->ident = V4L2_IDENT_SAA7118; + break; + default: + state->ident = V4L2_IDENT_SAA7111; + v4l_info(client, "WARNING: Chip is not known - Falling back to saa7111\n"); + } state->audclk_freq = 48000; @@ -1484,7 +1605,8 @@ static int saa7115_attach(struct i2c_adapter *adapter, int address, int kind) v4l_dbg(1, debug, client, "writing init values\n"); /* init to 60hz/48khz */ - if (state->ident == V4L2_IDENT_SAA7113) { + if (state->ident == V4L2_IDENT_SAA7111 || + state->ident == V4L2_IDENT_SAA7113) { state->crystal_freq = SAA7115_FREQ_24_576_MHZ; saa7115_writeregs(client, saa7113_init_auto_input); } else { diff --git a/include/media/v4l2-common.h b/include/media/v4l2-common.h index 8721ac4a45a..ce24a6ad445 100644 --- a/include/media/v4l2-common.h +++ b/include/media/v4l2-common.h @@ -121,10 +121,17 @@ enum v4l2_chip_ident { /* general idents: reserved range 0-49 */ V4L2_IDENT_UNKNOWN = 0, - /* module saa7115: reserved range 100-149 */ + /* module saa7110: just ident= 100 */ + V4L2_IDENT_SAA7110 = 100, + + /* module saa7111: just ident= 101 */ + V4L2_IDENT_SAA7111 = 101, + + /* module saa7115: reserved range 102-149 */ V4L2_IDENT_SAA7113 = 103, V4L2_IDENT_SAA7114 = 104, V4L2_IDENT_SAA7115 = 105, + V4L2_IDENT_SAA7118 = 108, /* module saa7127: reserved range 150-199 */ V4L2_IDENT_SAA7127 = 157,