From: Greg Kroah-Hartman Date: Thu, 28 Jul 2005 18:37:33 +0000 (-0700) Subject: [PATCH] PCI: clean up pci.h and split pci register info to separate header file. X-Git-Tag: v2.6.14-rc1~492^2~20^2~11 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=4352dfd5cd9172f1ee425924a463b43e6157b840;p=linux-2.6-omap-h63xx.git [PATCH] PCI: clean up pci.h and split pci register info to separate header file. This cleans up some of the #ifdef CONFIG_PCI stuff up, and moves the pci register info out to a separate file, where it belongs. Eventually we can stop including this file from within pci.h, but lots of code needs to be audited first. Signed-off-by: Greg Kroah-Hartman --- diff --git a/include/linux/pci.h b/include/linux/pci.h index e7a228f2fdd..830c1bae56c 100644 --- a/include/linux/pci.h +++ b/include/linux/pci.h @@ -19,436 +19,10 @@ #include -/* - * Under PCI, each device has 256 bytes of configuration address space, - * of which the first 64 bytes are standardized as follows: - */ -#define PCI_VENDOR_ID 0x00 /* 16 bits */ -#define PCI_DEVICE_ID 0x02 /* 16 bits */ -#define PCI_COMMAND 0x04 /* 16 bits */ -#define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */ -#define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */ -#define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */ -#define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */ -#define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */ -#define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */ -#define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */ -#define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */ -#define PCI_COMMAND_SERR 0x100 /* Enable SERR */ -#define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */ -#define PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */ - -#define PCI_STATUS 0x06 /* 16 bits */ -#define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */ -#define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */ -#define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */ -#define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */ -#define PCI_STATUS_PARITY 0x100 /* Detected parity error */ -#define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */ -#define PCI_STATUS_DEVSEL_FAST 0x000 -#define PCI_STATUS_DEVSEL_MEDIUM 0x200 -#define PCI_STATUS_DEVSEL_SLOW 0x400 -#define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */ -#define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */ -#define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */ -#define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */ -#define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */ - -#define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8 - revision */ -#define PCI_REVISION_ID 0x08 /* Revision ID */ -#define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */ -#define PCI_CLASS_DEVICE 0x0a /* Device class */ - -#define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */ -#define PCI_LATENCY_TIMER 0x0d /* 8 bits */ -#define PCI_HEADER_TYPE 0x0e /* 8 bits */ -#define PCI_HEADER_TYPE_NORMAL 0 -#define PCI_HEADER_TYPE_BRIDGE 1 -#define PCI_HEADER_TYPE_CARDBUS 2 - -#define PCI_BIST 0x0f /* 8 bits */ -#define PCI_BIST_CODE_MASK 0x0f /* Return result */ -#define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */ -#define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */ - -/* - * Base addresses specify locations in memory or I/O space. - * Decoded size can be determined by writing a value of - * 0xffffffff to the register, and reading it back. Only - * 1 bits are decoded. - */ -#define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */ -#define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */ -#define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */ -#define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */ -#define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */ -#define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */ -#define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */ -#define PCI_BASE_ADDRESS_SPACE_IO 0x01 -#define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00 -#define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06 -#define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */ -#define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */ -#define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */ -#define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */ -#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL) -#define PCI_BASE_ADDRESS_IO_MASK (~0x03UL) -/* bit 1 is reserved if address_space = 1 */ - -/* Header type 0 (normal devices) */ -#define PCI_CARDBUS_CIS 0x28 -#define PCI_SUBSYSTEM_VENDOR_ID 0x2c -#define PCI_SUBSYSTEM_ID 0x2e -#define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */ -#define PCI_ROM_ADDRESS_ENABLE 0x01 -#define PCI_ROM_ADDRESS_MASK (~0x7ffUL) - -#define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */ - -/* 0x35-0x3b are reserved */ -#define PCI_INTERRUPT_LINE 0x3c /* 8 bits */ -#define PCI_INTERRUPT_PIN 0x3d /* 8 bits */ -#define PCI_MIN_GNT 0x3e /* 8 bits */ -#define PCI_MAX_LAT 0x3f /* 8 bits */ - -/* Header type 1 (PCI-to-PCI bridges) */ -#define PCI_PRIMARY_BUS 0x18 /* Primary bus number */ -#define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */ -#define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */ -#define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */ -#define PCI_IO_BASE 0x1c /* I/O range behind the bridge */ -#define PCI_IO_LIMIT 0x1d -#define PCI_IO_RANGE_TYPE_MASK 0x0fUL /* I/O bridging type */ -#define PCI_IO_RANGE_TYPE_16 0x00 -#define PCI_IO_RANGE_TYPE_32 0x01 -#define PCI_IO_RANGE_MASK (~0x0fUL) -#define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */ -#define PCI_MEMORY_BASE 0x20 /* Memory range behind */ -#define PCI_MEMORY_LIMIT 0x22 -#define PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL -#define PCI_MEMORY_RANGE_MASK (~0x0fUL) -#define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */ -#define PCI_PREF_MEMORY_LIMIT 0x26 -#define PCI_PREF_RANGE_TYPE_MASK 0x0fUL -#define PCI_PREF_RANGE_TYPE_32 0x00 -#define PCI_PREF_RANGE_TYPE_64 0x01 -#define PCI_PREF_RANGE_MASK (~0x0fUL) -#define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */ -#define PCI_PREF_LIMIT_UPPER32 0x2c -#define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */ -#define PCI_IO_LIMIT_UPPER16 0x32 -/* 0x34 same as for htype 0 */ -/* 0x35-0x3b is reserved */ -#define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */ -/* 0x3c-0x3d are same as for htype 0 */ -#define PCI_BRIDGE_CONTROL 0x3e -#define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */ -#define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */ -#define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */ -#define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */ -#define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */ -#define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */ -#define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */ - -/* Header type 2 (CardBus bridges) */ -#define PCI_CB_CAPABILITY_LIST 0x14 -/* 0x15 reserved */ -#define PCI_CB_SEC_STATUS 0x16 /* Secondary status */ -#define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */ -#define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */ -#define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */ -#define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */ -#define PCI_CB_MEMORY_BASE_0 0x1c -#define PCI_CB_MEMORY_LIMIT_0 0x20 -#define PCI_CB_MEMORY_BASE_1 0x24 -#define PCI_CB_MEMORY_LIMIT_1 0x28 -#define PCI_CB_IO_BASE_0 0x2c -#define PCI_CB_IO_BASE_0_HI 0x2e -#define PCI_CB_IO_LIMIT_0 0x30 -#define PCI_CB_IO_LIMIT_0_HI 0x32 -#define PCI_CB_IO_BASE_1 0x34 -#define PCI_CB_IO_BASE_1_HI 0x36 -#define PCI_CB_IO_LIMIT_1 0x38 -#define PCI_CB_IO_LIMIT_1_HI 0x3a -#define PCI_CB_IO_RANGE_MASK (~0x03UL) -/* 0x3c-0x3d are same as for htype 0 */ -#define PCI_CB_BRIDGE_CONTROL 0x3e -#define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */ -#define PCI_CB_BRIDGE_CTL_SERR 0x02 -#define PCI_CB_BRIDGE_CTL_ISA 0x04 -#define PCI_CB_BRIDGE_CTL_VGA 0x08 -#define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20 -#define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */ -#define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */ -#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */ -#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200 -#define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400 -#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40 -#define PCI_CB_SUBSYSTEM_ID 0x42 -#define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */ -/* 0x48-0x7f reserved */ - -/* Capability lists */ - -#define PCI_CAP_LIST_ID 0 /* Capability ID */ -#define PCI_CAP_ID_PM 0x01 /* Power Management */ -#define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */ -#define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */ -#define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */ -#define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */ -#define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */ -#define PCI_CAP_ID_PCIX 0x07 /* PCI-X */ -#define PCI_CAP_ID_SHPC 0x0C /* PCI Standard Hot-Plug Controller */ -#define PCI_CAP_ID_EXP 0x10 /* PCI Express */ -#define PCI_CAP_ID_MSIX 0x11 /* MSI-X */ -#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */ -#define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */ -#define PCI_CAP_SIZEOF 4 - -/* Power Management Registers */ - -#define PCI_PM_PMC 2 /* PM Capabilities Register */ -#define PCI_PM_CAP_VER_MASK 0x0007 /* Version */ -#define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */ -#define PCI_PM_CAP_RESERVED 0x0010 /* Reserved field */ -#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */ -#define PCI_PM_CAP_AUX_POWER 0x01C0 /* Auxilliary power support mask */ -#define PCI_PM_CAP_D1 0x0200 /* D1 power state support */ -#define PCI_PM_CAP_D2 0x0400 /* D2 power state support */ -#define PCI_PM_CAP_PME 0x0800 /* PME pin supported */ -#define PCI_PM_CAP_PME_MASK 0xF800 /* PME Mask of all supported states */ -#define PCI_PM_CAP_PME_D0 0x0800 /* PME# from D0 */ -#define PCI_PM_CAP_PME_D1 0x1000 /* PME# from D1 */ -#define PCI_PM_CAP_PME_D2 0x2000 /* PME# from D2 */ -#define PCI_PM_CAP_PME_D3 0x4000 /* PME# from D3 (hot) */ -#define PCI_PM_CAP_PME_D3cold 0x8000 /* PME# from D3 (cold) */ -#define PCI_PM_CTRL 4 /* PM control and status register */ -#define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */ -#define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */ -#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */ -#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */ -#define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */ -#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */ -#define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */ -#define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */ -#define PCI_PM_DATA_REGISTER 7 /* (??) */ -#define PCI_PM_SIZEOF 8 - -/* AGP registers */ - -#define PCI_AGP_VERSION 2 /* BCD version number */ -#define PCI_AGP_RFU 3 /* Rest of capability flags */ -#define PCI_AGP_STATUS 4 /* Status register */ -#define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */ -#define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */ -#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */ -#define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */ -#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */ -#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */ -#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */ -#define PCI_AGP_COMMAND 8 /* Control register */ -#define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */ -#define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */ -#define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */ -#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */ -#define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */ -#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */ -#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate */ -#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate */ -#define PCI_AGP_SIZEOF 12 - -/* Vital Product Data */ - -#define PCI_VPD_ADDR 2 /* Address to access (15 bits!) */ -#define PCI_VPD_ADDR_MASK 0x7fff /* Address mask */ -#define PCI_VPD_ADDR_F 0x8000 /* Write 0, 1 indicates completion */ -#define PCI_VPD_DATA 4 /* 32-bits of data returned here */ - -/* Slot Identification */ - -#define PCI_SID_ESR 2 /* Expansion Slot Register */ -#define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */ -#define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */ -#define PCI_SID_CHASSIS_NR 3 /* Chassis Number */ - -/* Message Signalled Interrupts registers */ - -#define PCI_MSI_FLAGS 2 /* Various flags */ -#define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */ -#define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */ -#define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */ -#define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */ -#define PCI_MSI_FLAGS_MASKBIT 0x100 /* 64-bit mask bits allowed */ -#define PCI_MSI_RFU 3 /* Rest of capability flags */ -#define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */ -#define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */ -#define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */ -#define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */ -#define PCI_MSI_MASK_BIT 16 /* Mask bits register */ - -/* CompactPCI Hotswap Register */ - -#define PCI_CHSWP_CSR 2 /* Control and Status Register */ -#define PCI_CHSWP_DHA 0x01 /* Device Hiding Arm */ -#define PCI_CHSWP_EIM 0x02 /* ENUM# Signal Mask */ -#define PCI_CHSWP_PIE 0x04 /* Pending Insert or Extract */ -#define PCI_CHSWP_LOO 0x08 /* LED On / Off */ -#define PCI_CHSWP_PI 0x30 /* Programming Interface */ -#define PCI_CHSWP_EXT 0x40 /* ENUM# status - extraction */ -#define PCI_CHSWP_INS 0x80 /* ENUM# status - insertion */ - -/* PCI-X registers */ - -#define PCI_X_CMD 2 /* Modes & Features */ -#define PCI_X_CMD_DPERR_E 0x0001 /* Data Parity Error Recovery Enable */ -#define PCI_X_CMD_ERO 0x0002 /* Enable Relaxed Ordering */ -#define PCI_X_CMD_MAX_READ 0x000c /* Max Memory Read Byte Count */ -#define PCI_X_CMD_MAX_SPLIT 0x0070 /* Max Outstanding Split Transactions */ -#define PCI_X_CMD_VERSION(x) (((x) >> 12) & 3) /* Version */ -#define PCI_X_STATUS 4 /* PCI-X capabilities */ -#define PCI_X_STATUS_DEVFN 0x000000ff /* A copy of devfn */ -#define PCI_X_STATUS_BUS 0x0000ff00 /* A copy of bus nr */ -#define PCI_X_STATUS_64BIT 0x00010000 /* 64-bit device */ -#define PCI_X_STATUS_133MHZ 0x00020000 /* 133 MHz capable */ -#define PCI_X_STATUS_SPL_DISC 0x00040000 /* Split Completion Discarded */ -#define PCI_X_STATUS_UNX_SPL 0x00080000 /* Unexpected Split Completion */ -#define PCI_X_STATUS_COMPLEX 0x00100000 /* Device Complexity */ -#define PCI_X_STATUS_MAX_READ 0x00600000 /* Designed Max Memory Read Count */ -#define PCI_X_STATUS_MAX_SPLIT 0x03800000 /* Designed Max Outstanding Split Transactions */ -#define PCI_X_STATUS_MAX_CUM 0x1c000000 /* Designed Max Cumulative Read Size */ -#define PCI_X_STATUS_SPL_ERR 0x20000000 /* Rcvd Split Completion Error Msg */ -#define PCI_X_STATUS_266MHZ 0x40000000 /* 266 MHz capable */ -#define PCI_X_STATUS_533MHZ 0x80000000 /* 533 MHz capable */ - -/* PCI Express capability registers */ - -#define PCI_EXP_FLAGS 2 /* Capabilities register */ -#define PCI_EXP_FLAGS_VERS 0x000f /* Capability version */ -#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ -#define PCI_EXP_TYPE_ENDPOINT 0x0 /* Express Endpoint */ -#define PCI_EXP_TYPE_LEG_END 0x1 /* Legacy Endpoint */ -#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ -#define PCI_EXP_TYPE_UPSTREAM 0x5 /* Upstream Port */ -#define PCI_EXP_TYPE_DOWNSTREAM 0x6 /* Downstream Port */ -#define PCI_EXP_TYPE_PCI_BRIDGE 0x7 /* PCI/PCI-X Bridge */ -#define PCI_EXP_FLAGS_SLOT 0x0100 /* Slot implemented */ -#define PCI_EXP_FLAGS_IRQ 0x3e00 /* Interrupt message number */ -#define PCI_EXP_DEVCAP 4 /* Device capabilities */ -#define PCI_EXP_DEVCAP_PAYLOAD 0x07 /* Max_Payload_Size */ -#define PCI_EXP_DEVCAP_PHANTOM 0x18 /* Phantom functions */ -#define PCI_EXP_DEVCAP_EXT_TAG 0x20 /* Extended tags */ -#define PCI_EXP_DEVCAP_L0S 0x1c0 /* L0s Acceptable Latency */ -#define PCI_EXP_DEVCAP_L1 0xe00 /* L1 Acceptable Latency */ -#define PCI_EXP_DEVCAP_ATN_BUT 0x1000 /* Attention Button Present */ -#define PCI_EXP_DEVCAP_ATN_IND 0x2000 /* Attention Indicator Present */ -#define PCI_EXP_DEVCAP_PWR_IND 0x4000 /* Power Indicator Present */ -#define PCI_EXP_DEVCAP_PWR_VAL 0x3fc0000 /* Slot Power Limit Value */ -#define PCI_EXP_DEVCAP_PWR_SCL 0xc000000 /* Slot Power Limit Scale */ -#define PCI_EXP_DEVCTL 8 /* Device Control */ -#define PCI_EXP_DEVCTL_CERE 0x0001 /* Correctable Error Reporting En. */ -#define PCI_EXP_DEVCTL_NFERE 0x0002 /* Non-Fatal Error Reporting Enable */ -#define PCI_EXP_DEVCTL_FERE 0x0004 /* Fatal Error Reporting Enable */ -#define PCI_EXP_DEVCTL_URRE 0x0008 /* Unsupported Request Reporting En. */ -#define PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */ -#define PCI_EXP_DEVCTL_PAYLOAD 0x00e0 /* Max_Payload_Size */ -#define PCI_EXP_DEVCTL_EXT_TAG 0x0100 /* Extended Tag Field Enable */ -#define PCI_EXP_DEVCTL_PHANTOM 0x0200 /* Phantom Functions Enable */ -#define PCI_EXP_DEVCTL_AUX_PME 0x0400 /* Auxiliary Power PM Enable */ -#define PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800 /* Enable No Snoop */ -#define PCI_EXP_DEVCTL_READRQ 0x7000 /* Max_Read_Request_Size */ -#define PCI_EXP_DEVSTA 10 /* Device Status */ -#define PCI_EXP_DEVSTA_CED 0x01 /* Correctable Error Detected */ -#define PCI_EXP_DEVSTA_NFED 0x02 /* Non-Fatal Error Detected */ -#define PCI_EXP_DEVSTA_FED 0x04 /* Fatal Error Detected */ -#define PCI_EXP_DEVSTA_URD 0x08 /* Unsupported Request Detected */ -#define PCI_EXP_DEVSTA_AUXPD 0x10 /* AUX Power Detected */ -#define PCI_EXP_DEVSTA_TRPND 0x20 /* Transactions Pending */ -#define PCI_EXP_LNKCAP 12 /* Link Capabilities */ -#define PCI_EXP_LNKCTL 16 /* Link Control */ -#define PCI_EXP_LNKSTA 18 /* Link Status */ -#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ -#define PCI_EXP_SLTCTL 24 /* Slot Control */ -#define PCI_EXP_SLTSTA 26 /* Slot Status */ -#define PCI_EXP_RTCTL 28 /* Root Control */ -#define PCI_EXP_RTCTL_SECEE 0x01 /* System Error on Correctable Error */ -#define PCI_EXP_RTCTL_SENFEE 0x02 /* System Error on Non-Fatal Error */ -#define PCI_EXP_RTCTL_SEFEE 0x04 /* System Error on Fatal Error */ -#define PCI_EXP_RTCTL_PMEIE 0x08 /* PME Interrupt Enable */ -#define PCI_EXP_RTCTL_CRSSVE 0x10 /* CRS Software Visibility Enable */ -#define PCI_EXP_RTCAP 30 /* Root Capabilities */ -#define PCI_EXP_RTSTA 32 /* Root Status */ - -/* Extended Capabilities (PCI-X 2.0 and Express) */ -#define PCI_EXT_CAP_ID(header) (header & 0x0000ffff) -#define PCI_EXT_CAP_VER(header) ((header >> 16) & 0xf) -#define PCI_EXT_CAP_NEXT(header) ((header >> 20) & 0xffc) - -#define PCI_EXT_CAP_ID_ERR 1 -#define PCI_EXT_CAP_ID_VC 2 -#define PCI_EXT_CAP_ID_DSN 3 -#define PCI_EXT_CAP_ID_PWR 4 - -/* Advanced Error Reporting */ -#define PCI_ERR_UNCOR_STATUS 4 /* Uncorrectable Error Status */ -#define PCI_ERR_UNC_TRAIN 0x00000001 /* Training */ -#define PCI_ERR_UNC_DLP 0x00000010 /* Data Link Protocol */ -#define PCI_ERR_UNC_POISON_TLP 0x00001000 /* Poisoned TLP */ -#define PCI_ERR_UNC_FCP 0x00002000 /* Flow Control Protocol */ -#define PCI_ERR_UNC_COMP_TIME 0x00004000 /* Completion Timeout */ -#define PCI_ERR_UNC_COMP_ABORT 0x00008000 /* Completer Abort */ -#define PCI_ERR_UNC_UNX_COMP 0x00010000 /* Unexpected Completion */ -#define PCI_ERR_UNC_RX_OVER 0x00020000 /* Receiver Overflow */ -#define PCI_ERR_UNC_MALF_TLP 0x00040000 /* Malformed TLP */ -#define PCI_ERR_UNC_ECRC 0x00080000 /* ECRC Error Status */ -#define PCI_ERR_UNC_UNSUP 0x00100000 /* Unsupported Request */ -#define PCI_ERR_UNCOR_MASK 8 /* Uncorrectable Error Mask */ - /* Same bits as above */ -#define PCI_ERR_UNCOR_SEVER 12 /* Uncorrectable Error Severity */ - /* Same bits as above */ -#define PCI_ERR_COR_STATUS 16 /* Correctable Error Status */ -#define PCI_ERR_COR_RCVR 0x00000001 /* Receiver Error Status */ -#define PCI_ERR_COR_BAD_TLP 0x00000040 /* Bad TLP Status */ -#define PCI_ERR_COR_BAD_DLLP 0x00000080 /* Bad DLLP Status */ -#define PCI_ERR_COR_REP_ROLL 0x00000100 /* REPLAY_NUM Rollover */ -#define PCI_ERR_COR_REP_TIMER 0x00001000 /* Replay Timer Timeout */ -#define PCI_ERR_COR_MASK 20 /* Correctable Error Mask */ - /* Same bits as above */ -#define PCI_ERR_CAP 24 /* Advanced Error Capabilities */ -#define PCI_ERR_CAP_FEP(x) ((x) & 31) /* First Error Pointer */ -#define PCI_ERR_CAP_ECRC_GENC 0x00000020 /* ECRC Generation Capable */ -#define PCI_ERR_CAP_ECRC_GENE 0x00000040 /* ECRC Generation Enable */ -#define PCI_ERR_CAP_ECRC_CHKC 0x00000080 /* ECRC Check Capable */ -#define PCI_ERR_CAP_ECRC_CHKE 0x00000100 /* ECRC Check Enable */ -#define PCI_ERR_HEADER_LOG 28 /* Header Log Register (16 bytes) */ -#define PCI_ERR_ROOT_COMMAND 44 /* Root Error Command */ -#define PCI_ERR_ROOT_STATUS 48 -#define PCI_ERR_ROOT_COR_SRC 52 -#define PCI_ERR_ROOT_SRC 54 - -/* Virtual Channel */ -#define PCI_VC_PORT_REG1 4 -#define PCI_VC_PORT_REG2 8 -#define PCI_VC_PORT_CTRL 12 -#define PCI_VC_PORT_STATUS 14 -#define PCI_VC_RES_CAP 16 -#define PCI_VC_RES_CTRL 20 -#define PCI_VC_RES_STATUS 26 - -/* Power Budgeting */ -#define PCI_PWR_DSR 4 /* Data Select Register */ -#define PCI_PWR_DATA 8 /* Data Register */ -#define PCI_PWR_DATA_BASE(x) ((x) & 0xff) /* Base Power */ -#define PCI_PWR_DATA_SCALE(x) (((x) >> 8) & 3) /* Data Scale */ -#define PCI_PWR_DATA_PM_SUB(x) (((x) >> 10) & 7) /* PM Sub State */ -#define PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */ -#define PCI_PWR_DATA_TYPE(x) (((x) >> 15) & 7) /* Type */ -#define PCI_PWR_DATA_RAIL(x) (((x) >> 18) & 7) /* Power Rail */ -#define PCI_PWR_CAP 12 /* Capability */ -#define PCI_PWR_CAP_BUDGET(x) ((x) & 1) /* Included in system budget */ +/* Include the pci register defines */ +#include /* Include the ID list */ - #include /* @@ -496,9 +70,9 @@ enum pci_mmap_state { typedef int __bitwise pci_power_t; -#define PCI_D0 ((pci_power_t __force) 0) -#define PCI_D1 ((pci_power_t __force) 1) -#define PCI_D2 ((pci_power_t __force) 2) +#define PCI_D0 ((pci_power_t __force) 0) +#define PCI_D1 ((pci_power_t __force) 1) +#define PCI_D2 ((pci_power_t __force) 2) #define PCI_D3hot ((pci_power_t __force) 3) #define PCI_D3cold ((pci_power_t __force) 4) #define PCI_POWER_ERROR ((pci_power_t __force) -1) @@ -577,15 +151,15 @@ struct pci_dev { * 7-10 bridges: address space assigned to buses behind the bridge */ -#define PCI_ROM_RESOURCE 6 -#define PCI_BRIDGE_RESOURCES 7 -#define PCI_NUM_RESOURCES 11 +#define PCI_ROM_RESOURCE 6 +#define PCI_BRIDGE_RESOURCES 7 +#define PCI_NUM_RESOURCES 11 #ifndef PCI_BUS_NUM_RESOURCES -#define PCI_BUS_NUM_RESOURCES 8 +#define PCI_BUS_NUM_RESOURCES 8 #endif - -#define PCI_REGION_FLAG_MASK 0x0fU /* These bits of resource flags tell us the PCI region flags */ + +#define PCI_REGION_FLAG_MASK 0x0fU /* These bits of resource flags tell us the PCI region flags */ struct pci_bus { struct list_head node; /* node in list of buses */ @@ -694,7 +268,7 @@ struct pci_driver { * @dev_class_mask: the class mask for this device * * This macro is used to create a struct pci_device_id that matches a - * specific PCI class. The vendor, device, subvendor, and subdevice + * specific PCI class. The vendor, device, subvendor, and subdevice * fields will be set to PCI_ANY_ID. */ #define PCI_DEVICE_CLASS(dev_class,dev_class_mask) \ @@ -702,7 +276,7 @@ struct pci_driver { .vendor = PCI_ANY_ID, .device = PCI_ANY_ID, \ .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID -/* +/* * pci_module_init is obsolete, this stays here till we fix up all usages of it * in the tree. */ @@ -905,18 +479,26 @@ extern void pci_disable_msix(struct pci_dev *dev); extern void msi_remove_pci_irq_vectors(struct pci_dev *dev); #endif -#endif /* CONFIG_PCI */ - -/* Include architecture-dependent settings and functions */ +/* + * PCI domain support. Sometimes called PCI segment (eg by ACPI), + * a PCI domain is defined to be a set of PCI busses which share + * configuration space. + */ +#ifndef CONFIG_PCI_DOMAINS +static inline int pci_domain_nr(struct pci_bus *bus) { return 0; } +static inline int pci_proc_domain(struct pci_bus *bus) +{ + return 0; +} +#endif -#include +#else /* CONFIG_PCI is not enabled */ /* * If the system does not have PCI, clearly these return errors. Define * these as simple inline functions to avoid hair in drivers. */ -#ifndef CONFIG_PCI #define _PCI_NOP(o,s,t) \ static inline int pci_##o##_config_##s (struct pci_dev *dev, int where, t val) \ { return PCIBIOS_FUNC_NOT_SUPPORTED; } @@ -967,21 +549,11 @@ static inline int pci_enable_wake(struct pci_dev *dev, pci_power_t state, int en #define pci_dma_burst_advice(pdev, strat, strategy_parameter) do { } while (0) -#else +#endif /* CONFIG_PCI */ -/* - * PCI domain support. Sometimes called PCI segment (eg by ACPI), - * a PCI domain is defined to be a set of PCI busses which share - * configuration space. - */ -#ifndef CONFIG_PCI_DOMAINS -static inline int pci_domain_nr(struct pci_bus *bus) { return 0; } -static inline int pci_proc_domain(struct pci_bus *bus) -{ - return 0; -} -#endif -#endif /* !CONFIG_PCI */ +/* Include architecture-dependent settings and functions */ + +#include /* these helpers provide future and backwards compatibility * for accessing popular PCI BAR info */ diff --git a/include/linux/pci_regs.h b/include/linux/pci_regs.h new file mode 100644 index 00000000000..7dc391cad10 --- /dev/null +++ b/include/linux/pci_regs.h @@ -0,0 +1,447 @@ +/* + * pci_regs.h + * + * PCI standard defines + * Copyright 1994, Drew Eckhardt + * Copyright 1997--1999 Martin Mares + * + * For more information, please consult the following manuals (look at + * http://www.pcisig.com/ for how to get them): + * + * PCI BIOS Specification + * PCI Local Bus Specification + * PCI to PCI Bridge Specification + * PCI System Design Guide + */ + +#ifndef LINUX_PCI_REGS_H +#define LINUX_PCI_REGS_H + +/* + * Under PCI, each device has 256 bytes of configuration address space, + * of which the first 64 bytes are standardized as follows: + */ +#define PCI_VENDOR_ID 0x00 /* 16 bits */ +#define PCI_DEVICE_ID 0x02 /* 16 bits */ +#define PCI_COMMAND 0x04 /* 16 bits */ +#define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */ +#define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */ +#define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */ +#define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */ +#define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */ +#define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */ +#define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */ +#define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */ +#define PCI_COMMAND_SERR 0x100 /* Enable SERR */ +#define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */ +#define PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */ + +#define PCI_STATUS 0x06 /* 16 bits */ +#define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */ +#define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */ +#define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */ +#define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */ +#define PCI_STATUS_PARITY 0x100 /* Detected parity error */ +#define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */ +#define PCI_STATUS_DEVSEL_FAST 0x000 +#define PCI_STATUS_DEVSEL_MEDIUM 0x200 +#define PCI_STATUS_DEVSEL_SLOW 0x400 +#define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */ +#define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */ +#define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */ +#define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */ +#define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */ + +#define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8 revision */ +#define PCI_REVISION_ID 0x08 /* Revision ID */ +#define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */ +#define PCI_CLASS_DEVICE 0x0a /* Device class */ + +#define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */ +#define PCI_LATENCY_TIMER 0x0d /* 8 bits */ +#define PCI_HEADER_TYPE 0x0e /* 8 bits */ +#define PCI_HEADER_TYPE_NORMAL 0 +#define PCI_HEADER_TYPE_BRIDGE 1 +#define PCI_HEADER_TYPE_CARDBUS 2 + +#define PCI_BIST 0x0f /* 8 bits */ +#define PCI_BIST_CODE_MASK 0x0f /* Return result */ +#define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */ +#define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */ + +/* + * Base addresses specify locations in memory or I/O space. + * Decoded size can be determined by writing a value of + * 0xffffffff to the register, and reading it back. Only + * 1 bits are decoded. + */ +#define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */ +#define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */ +#define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */ +#define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */ +#define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */ +#define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */ +#define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */ +#define PCI_BASE_ADDRESS_SPACE_IO 0x01 +#define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00 +#define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06 +#define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */ +#define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */ +#define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */ +#define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */ +#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL) +#define PCI_BASE_ADDRESS_IO_MASK (~0x03UL) +/* bit 1 is reserved if address_space = 1 */ + +/* Header type 0 (normal devices) */ +#define PCI_CARDBUS_CIS 0x28 +#define PCI_SUBSYSTEM_VENDOR_ID 0x2c +#define PCI_SUBSYSTEM_ID 0x2e +#define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */ +#define PCI_ROM_ADDRESS_ENABLE 0x01 +#define PCI_ROM_ADDRESS_MASK (~0x7ffUL) + +#define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */ + +/* 0x35-0x3b are reserved */ +#define PCI_INTERRUPT_LINE 0x3c /* 8 bits */ +#define PCI_INTERRUPT_PIN 0x3d /* 8 bits */ +#define PCI_MIN_GNT 0x3e /* 8 bits */ +#define PCI_MAX_LAT 0x3f /* 8 bits */ + +/* Header type 1 (PCI-to-PCI bridges) */ +#define PCI_PRIMARY_BUS 0x18 /* Primary bus number */ +#define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */ +#define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */ +#define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */ +#define PCI_IO_BASE 0x1c /* I/O range behind the bridge */ +#define PCI_IO_LIMIT 0x1d +#define PCI_IO_RANGE_TYPE_MASK 0x0fUL /* I/O bridging type */ +#define PCI_IO_RANGE_TYPE_16 0x00 +#define PCI_IO_RANGE_TYPE_32 0x01 +#define PCI_IO_RANGE_MASK (~0x0fUL) +#define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */ +#define PCI_MEMORY_BASE 0x20 /* Memory range behind */ +#define PCI_MEMORY_LIMIT 0x22 +#define PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL +#define PCI_MEMORY_RANGE_MASK (~0x0fUL) +#define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */ +#define PCI_PREF_MEMORY_LIMIT 0x26 +#define PCI_PREF_RANGE_TYPE_MASK 0x0fUL +#define PCI_PREF_RANGE_TYPE_32 0x00 +#define PCI_PREF_RANGE_TYPE_64 0x01 +#define PCI_PREF_RANGE_MASK (~0x0fUL) +#define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */ +#define PCI_PREF_LIMIT_UPPER32 0x2c +#define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */ +#define PCI_IO_LIMIT_UPPER16 0x32 +/* 0x34 same as for htype 0 */ +/* 0x35-0x3b is reserved */ +#define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */ +/* 0x3c-0x3d are same as for htype 0 */ +#define PCI_BRIDGE_CONTROL 0x3e +#define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */ +#define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */ +#define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */ +#define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */ +#define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */ +#define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */ +#define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */ + +/* Header type 2 (CardBus bridges) */ +#define PCI_CB_CAPABILITY_LIST 0x14 +/* 0x15 reserved */ +#define PCI_CB_SEC_STATUS 0x16 /* Secondary status */ +#define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */ +#define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */ +#define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */ +#define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */ +#define PCI_CB_MEMORY_BASE_0 0x1c +#define PCI_CB_MEMORY_LIMIT_0 0x20 +#define PCI_CB_MEMORY_BASE_1 0x24 +#define PCI_CB_MEMORY_LIMIT_1 0x28 +#define PCI_CB_IO_BASE_0 0x2c +#define PCI_CB_IO_BASE_0_HI 0x2e +#define PCI_CB_IO_LIMIT_0 0x30 +#define PCI_CB_IO_LIMIT_0_HI 0x32 +#define PCI_CB_IO_BASE_1 0x34 +#define PCI_CB_IO_BASE_1_HI 0x36 +#define PCI_CB_IO_LIMIT_1 0x38 +#define PCI_CB_IO_LIMIT_1_HI 0x3a +#define PCI_CB_IO_RANGE_MASK (~0x03UL) +/* 0x3c-0x3d are same as for htype 0 */ +#define PCI_CB_BRIDGE_CONTROL 0x3e +#define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */ +#define PCI_CB_BRIDGE_CTL_SERR 0x02 +#define PCI_CB_BRIDGE_CTL_ISA 0x04 +#define PCI_CB_BRIDGE_CTL_VGA 0x08 +#define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20 +#define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */ +#define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */ +#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */ +#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200 +#define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400 +#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40 +#define PCI_CB_SUBSYSTEM_ID 0x42 +#define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */ +/* 0x48-0x7f reserved */ + +/* Capability lists */ + +#define PCI_CAP_LIST_ID 0 /* Capability ID */ +#define PCI_CAP_ID_PM 0x01 /* Power Management */ +#define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */ +#define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */ +#define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */ +#define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */ +#define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */ +#define PCI_CAP_ID_PCIX 0x07 /* PCI-X */ +#define PCI_CAP_ID_SHPC 0x0C /* PCI Standard Hot-Plug Controller */ +#define PCI_CAP_ID_EXP 0x10 /* PCI Express */ +#define PCI_CAP_ID_MSIX 0x11 /* MSI-X */ +#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */ +#define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */ +#define PCI_CAP_SIZEOF 4 + +/* Power Management Registers */ + +#define PCI_PM_PMC 2 /* PM Capabilities Register */ +#define PCI_PM_CAP_VER_MASK 0x0007 /* Version */ +#define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */ +#define PCI_PM_CAP_RESERVED 0x0010 /* Reserved field */ +#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */ +#define PCI_PM_CAP_AUX_POWER 0x01C0 /* Auxilliary power support mask */ +#define PCI_PM_CAP_D1 0x0200 /* D1 power state support */ +#define PCI_PM_CAP_D2 0x0400 /* D2 power state support */ +#define PCI_PM_CAP_PME 0x0800 /* PME pin supported */ +#define PCI_PM_CAP_PME_MASK 0xF800 /* PME Mask of all supported states */ +#define PCI_PM_CAP_PME_D0 0x0800 /* PME# from D0 */ +#define PCI_PM_CAP_PME_D1 0x1000 /* PME# from D1 */ +#define PCI_PM_CAP_PME_D2 0x2000 /* PME# from D2 */ +#define PCI_PM_CAP_PME_D3 0x4000 /* PME# from D3 (hot) */ +#define PCI_PM_CAP_PME_D3cold 0x8000 /* PME# from D3 (cold) */ +#define PCI_PM_CTRL 4 /* PM control and status register */ +#define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */ +#define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */ +#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */ +#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */ +#define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */ +#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */ +#define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */ +#define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */ +#define PCI_PM_DATA_REGISTER 7 /* (??) */ +#define PCI_PM_SIZEOF 8 + +/* AGP registers */ + +#define PCI_AGP_VERSION 2 /* BCD version number */ +#define PCI_AGP_RFU 3 /* Rest of capability flags */ +#define PCI_AGP_STATUS 4 /* Status register */ +#define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */ +#define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */ +#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */ +#define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */ +#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */ +#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */ +#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */ +#define PCI_AGP_COMMAND 8 /* Control register */ +#define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */ +#define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */ +#define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */ +#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */ +#define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */ +#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */ +#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate */ +#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate */ +#define PCI_AGP_SIZEOF 12 + +/* Vital Product Data */ + +#define PCI_VPD_ADDR 2 /* Address to access (15 bits!) */ +#define PCI_VPD_ADDR_MASK 0x7fff /* Address mask */ +#define PCI_VPD_ADDR_F 0x8000 /* Write 0, 1 indicates completion */ +#define PCI_VPD_DATA 4 /* 32-bits of data returned here */ + +/* Slot Identification */ + +#define PCI_SID_ESR 2 /* Expansion Slot Register */ +#define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */ +#define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */ +#define PCI_SID_CHASSIS_NR 3 /* Chassis Number */ + +/* Message Signalled Interrupts registers */ + +#define PCI_MSI_FLAGS 2 /* Various flags */ +#define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */ +#define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */ +#define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */ +#define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */ +#define PCI_MSI_FLAGS_MASKBIT 0x100 /* 64-bit mask bits allowed */ +#define PCI_MSI_RFU 3 /* Rest of capability flags */ +#define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */ +#define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */ +#define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */ +#define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */ +#define PCI_MSI_MASK_BIT 16 /* Mask bits register */ + +/* CompactPCI Hotswap Register */ + +#define PCI_CHSWP_CSR 2 /* Control and Status Register */ +#define PCI_CHSWP_DHA 0x01 /* Device Hiding Arm */ +#define PCI_CHSWP_EIM 0x02 /* ENUM# Signal Mask */ +#define PCI_CHSWP_PIE 0x04 /* Pending Insert or Extract */ +#define PCI_CHSWP_LOO 0x08 /* LED On / Off */ +#define PCI_CHSWP_PI 0x30 /* Programming Interface */ +#define PCI_CHSWP_EXT 0x40 /* ENUM# status - extraction */ +#define PCI_CHSWP_INS 0x80 /* ENUM# status - insertion */ + +/* PCI-X registers */ + +#define PCI_X_CMD 2 /* Modes & Features */ +#define PCI_X_CMD_DPERR_E 0x0001 /* Data Parity Error Recovery Enable */ +#define PCI_X_CMD_ERO 0x0002 /* Enable Relaxed Ordering */ +#define PCI_X_CMD_MAX_READ 0x000c /* Max Memory Read Byte Count */ +#define PCI_X_CMD_MAX_SPLIT 0x0070 /* Max Outstanding Split Transactions */ +#define PCI_X_CMD_VERSION(x) (((x) >> 12) & 3) /* Version */ +#define PCI_X_STATUS 4 /* PCI-X capabilities */ +#define PCI_X_STATUS_DEVFN 0x000000ff /* A copy of devfn */ +#define PCI_X_STATUS_BUS 0x0000ff00 /* A copy of bus nr */ +#define PCI_X_STATUS_64BIT 0x00010000 /* 64-bit device */ +#define PCI_X_STATUS_133MHZ 0x00020000 /* 133 MHz capable */ +#define PCI_X_STATUS_SPL_DISC 0x00040000 /* Split Completion Discarded */ +#define PCI_X_STATUS_UNX_SPL 0x00080000 /* Unexpected Split Completion */ +#define PCI_X_STATUS_COMPLEX 0x00100000 /* Device Complexity */ +#define PCI_X_STATUS_MAX_READ 0x00600000 /* Designed Max Memory Read Count */ +#define PCI_X_STATUS_MAX_SPLIT 0x03800000 /* Designed Max Outstanding Split Transactions */ +#define PCI_X_STATUS_MAX_CUM 0x1c000000 /* Designed Max Cumulative Read Size */ +#define PCI_X_STATUS_SPL_ERR 0x20000000 /* Rcvd Split Completion Error Msg */ +#define PCI_X_STATUS_266MHZ 0x40000000 /* 266 MHz capable */ +#define PCI_X_STATUS_533MHZ 0x80000000 /* 533 MHz capable */ + +/* PCI Express capability registers */ + +#define PCI_EXP_FLAGS 2 /* Capabilities register */ +#define PCI_EXP_FLAGS_VERS 0x000f /* Capability version */ +#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ +#define PCI_EXP_TYPE_ENDPOINT 0x0 /* Express Endpoint */ +#define PCI_EXP_TYPE_LEG_END 0x1 /* Legacy Endpoint */ +#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ +#define PCI_EXP_TYPE_UPSTREAM 0x5 /* Upstream Port */ +#define PCI_EXP_TYPE_DOWNSTREAM 0x6 /* Downstream Port */ +#define PCI_EXP_TYPE_PCI_BRIDGE 0x7 /* PCI/PCI-X Bridge */ +#define PCI_EXP_FLAGS_SLOT 0x0100 /* Slot implemented */ +#define PCI_EXP_FLAGS_IRQ 0x3e00 /* Interrupt message number */ +#define PCI_EXP_DEVCAP 4 /* Device capabilities */ +#define PCI_EXP_DEVCAP_PAYLOAD 0x07 /* Max_Payload_Size */ +#define PCI_EXP_DEVCAP_PHANTOM 0x18 /* Phantom functions */ +#define PCI_EXP_DEVCAP_EXT_TAG 0x20 /* Extended tags */ +#define PCI_EXP_DEVCAP_L0S 0x1c0 /* L0s Acceptable Latency */ +#define PCI_EXP_DEVCAP_L1 0xe00 /* L1 Acceptable Latency */ +#define PCI_EXP_DEVCAP_ATN_BUT 0x1000 /* Attention Button Present */ +#define PCI_EXP_DEVCAP_ATN_IND 0x2000 /* Attention Indicator Present */ +#define PCI_EXP_DEVCAP_PWR_IND 0x4000 /* Power Indicator Present */ +#define PCI_EXP_DEVCAP_PWR_VAL 0x3fc0000 /* Slot Power Limit Value */ +#define PCI_EXP_DEVCAP_PWR_SCL 0xc000000 /* Slot Power Limit Scale */ +#define PCI_EXP_DEVCTL 8 /* Device Control */ +#define PCI_EXP_DEVCTL_CERE 0x0001 /* Correctable Error Reporting En. */ +#define PCI_EXP_DEVCTL_NFERE 0x0002 /* Non-Fatal Error Reporting Enable */ +#define PCI_EXP_DEVCTL_FERE 0x0004 /* Fatal Error Reporting Enable */ +#define PCI_EXP_DEVCTL_URRE 0x0008 /* Unsupported Request Reporting En. */ +#define PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */ +#define PCI_EXP_DEVCTL_PAYLOAD 0x00e0 /* Max_Payload_Size */ +#define PCI_EXP_DEVCTL_EXT_TAG 0x0100 /* Extended Tag Field Enable */ +#define PCI_EXP_DEVCTL_PHANTOM 0x0200 /* Phantom Functions Enable */ +#define PCI_EXP_DEVCTL_AUX_PME 0x0400 /* Auxiliary Power PM Enable */ +#define PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800 /* Enable No Snoop */ +#define PCI_EXP_DEVCTL_READRQ 0x7000 /* Max_Read_Request_Size */ +#define PCI_EXP_DEVSTA 10 /* Device Status */ +#define PCI_EXP_DEVSTA_CED 0x01 /* Correctable Error Detected */ +#define PCI_EXP_DEVSTA_NFED 0x02 /* Non-Fatal Error Detected */ +#define PCI_EXP_DEVSTA_FED 0x04 /* Fatal Error Detected */ +#define PCI_EXP_DEVSTA_URD 0x08 /* Unsupported Request Detected */ +#define PCI_EXP_DEVSTA_AUXPD 0x10 /* AUX Power Detected */ +#define PCI_EXP_DEVSTA_TRPND 0x20 /* Transactions Pending */ +#define PCI_EXP_LNKCAP 12 /* Link Capabilities */ +#define PCI_EXP_LNKCTL 16 /* Link Control */ +#define PCI_EXP_LNKSTA 18 /* Link Status */ +#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ +#define PCI_EXP_SLTCTL 24 /* Slot Control */ +#define PCI_EXP_SLTSTA 26 /* Slot Status */ +#define PCI_EXP_RTCTL 28 /* Root Control */ +#define PCI_EXP_RTCTL_SECEE 0x01 /* System Error on Correctable Error */ +#define PCI_EXP_RTCTL_SENFEE 0x02 /* System Error on Non-Fatal Error */ +#define PCI_EXP_RTCTL_SEFEE 0x04 /* System Error on Fatal Error */ +#define PCI_EXP_RTCTL_PMEIE 0x08 /* PME Interrupt Enable */ +#define PCI_EXP_RTCTL_CRSSVE 0x10 /* CRS Software Visibility Enable */ +#define PCI_EXP_RTCAP 30 /* Root Capabilities */ +#define PCI_EXP_RTSTA 32 /* Root Status */ + +/* Extended Capabilities (PCI-X 2.0 and Express) */ +#define PCI_EXT_CAP_ID(header) (header & 0x0000ffff) +#define PCI_EXT_CAP_VER(header) ((header >> 16) & 0xf) +#define PCI_EXT_CAP_NEXT(header) ((header >> 20) & 0xffc) + +#define PCI_EXT_CAP_ID_ERR 1 +#define PCI_EXT_CAP_ID_VC 2 +#define PCI_EXT_CAP_ID_DSN 3 +#define PCI_EXT_CAP_ID_PWR 4 + +/* Advanced Error Reporting */ +#define PCI_ERR_UNCOR_STATUS 4 /* Uncorrectable Error Status */ +#define PCI_ERR_UNC_TRAIN 0x00000001 /* Training */ +#define PCI_ERR_UNC_DLP 0x00000010 /* Data Link Protocol */ +#define PCI_ERR_UNC_POISON_TLP 0x00001000 /* Poisoned TLP */ +#define PCI_ERR_UNC_FCP 0x00002000 /* Flow Control Protocol */ +#define PCI_ERR_UNC_COMP_TIME 0x00004000 /* Completion Timeout */ +#define PCI_ERR_UNC_COMP_ABORT 0x00008000 /* Completer Abort */ +#define PCI_ERR_UNC_UNX_COMP 0x00010000 /* Unexpected Completion */ +#define PCI_ERR_UNC_RX_OVER 0x00020000 /* Receiver Overflow */ +#define PCI_ERR_UNC_MALF_TLP 0x00040000 /* Malformed TLP */ +#define PCI_ERR_UNC_ECRC 0x00080000 /* ECRC Error Status */ +#define PCI_ERR_UNC_UNSUP 0x00100000 /* Unsupported Request */ +#define PCI_ERR_UNCOR_MASK 8 /* Uncorrectable Error Mask */ + /* Same bits as above */ +#define PCI_ERR_UNCOR_SEVER 12 /* Uncorrectable Error Severity */ + /* Same bits as above */ +#define PCI_ERR_COR_STATUS 16 /* Correctable Error Status */ +#define PCI_ERR_COR_RCVR 0x00000001 /* Receiver Error Status */ +#define PCI_ERR_COR_BAD_TLP 0x00000040 /* Bad TLP Status */ +#define PCI_ERR_COR_BAD_DLLP 0x00000080 /* Bad DLLP Status */ +#define PCI_ERR_COR_REP_ROLL 0x00000100 /* REPLAY_NUM Rollover */ +#define PCI_ERR_COR_REP_TIMER 0x00001000 /* Replay Timer Timeout */ +#define PCI_ERR_COR_MASK 20 /* Correctable Error Mask */ + /* Same bits as above */ +#define PCI_ERR_CAP 24 /* Advanced Error Capabilities */ +#define PCI_ERR_CAP_FEP(x) ((x) & 31) /* First Error Pointer */ +#define PCI_ERR_CAP_ECRC_GENC 0x00000020 /* ECRC Generation Capable */ +#define PCI_ERR_CAP_ECRC_GENE 0x00000040 /* ECRC Generation Enable */ +#define PCI_ERR_CAP_ECRC_CHKC 0x00000080 /* ECRC Check Capable */ +#define PCI_ERR_CAP_ECRC_CHKE 0x00000100 /* ECRC Check Enable */ +#define PCI_ERR_HEADER_LOG 28 /* Header Log Register (16 bytes) */ +#define PCI_ERR_ROOT_COMMAND 44 /* Root Error Command */ +#define PCI_ERR_ROOT_STATUS 48 +#define PCI_ERR_ROOT_COR_SRC 52 +#define PCI_ERR_ROOT_SRC 54 + +/* Virtual Channel */ +#define PCI_VC_PORT_REG1 4 +#define PCI_VC_PORT_REG2 8 +#define PCI_VC_PORT_CTRL 12 +#define PCI_VC_PORT_STATUS 14 +#define PCI_VC_RES_CAP 16 +#define PCI_VC_RES_CTRL 20 +#define PCI_VC_RES_STATUS 26 + +/* Power Budgeting */ +#define PCI_PWR_DSR 4 /* Data Select Register */ +#define PCI_PWR_DATA 8 /* Data Register */ +#define PCI_PWR_DATA_BASE(x) ((x) & 0xff) /* Base Power */ +#define PCI_PWR_DATA_SCALE(x) (((x) >> 8) & 3) /* Data Scale */ +#define PCI_PWR_DATA_PM_SUB(x) (((x) >> 10) & 7) /* PM Sub State */ +#define PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */ +#define PCI_PWR_DATA_TYPE(x) (((x) >> 15) & 7) /* Type */ +#define PCI_PWR_DATA_RAIL(x) (((x) >> 18) & 7) /* Power Rail */ +#define PCI_PWR_CAP 12 /* Capability */ +#define PCI_PWR_CAP_BUDGET(x) ((x) & 1) /* Included in system budget */ + +#endif /* LINUX_PCI_REGS_H */