From: Seth Forshee <seth.forshee@gmail.com>
Date: Tue, 1 Apr 2008 01:34:18 +0000 (-0500)
Subject: OMAP: HSMMC: Fix 1.8V MMC2 host on OMAP2430/3430
X-Git-Tag: v2.6.25-omap1~75
X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=398ef34eec300ba166eca3077f0137a3eced388e;p=linux-2.6-omap-h63xx.git

OMAP: HSMMC: Fix 1.8V MMC2 host on OMAP2430/3430

OMAP2430/3430 contain an 1.8V-only MMC2 host that is not properly
supported by the current driver.  This patch contains changes to
correctly set up this host.

Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Acked-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---

diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 248257f54c0..d5d82a85ff0 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -388,8 +388,12 @@ static int omap_mmc_switch_opcond(struct mmc_omap_host *host, int vdd)
 	 * If a MMC dual voltage card is detected, the set_ios fn calls
 	 * this fn with VDD bit set for 1.8V. Upon card removal from the
 	 * slot, mmc_omap_detect fn sets the VDD back to 3V.
+	 *
+	 * Only MMC1 supports 3.0V.  MMC2 will not function if SDVS30 is
+	 * set in HCTL.
 	 */
-	if (((1 << vdd) == MMC_VDD_32_33) || ((1 << vdd) == MMC_VDD_33_34))
+	if (host->id == OMAP_MMC1_DEVID && (((1 << vdd) == MMC_VDD_32_33) ||
+				((1 << vdd) == MMC_VDD_33_34)))
 		reg_val |= SDVS30;
 	if ((1 << vdd) == MMC_VDD_165_195)
 		reg_val |= SDVS18;
@@ -517,10 +521,16 @@ mmc_omap_start_dma_transfer(struct mmc_omap_host *host, struct mmc_request *req)
 
 	if (!(data->flags & MMC_DATA_WRITE)) {
 		host->dma_dir = DMA_FROM_DEVICE;
-		sync_dev = OMAP24XX_DMA_MMC1_RX;
+		if (host->id == OMAP_MMC1_DEVID)
+			sync_dev = OMAP24XX_DMA_MMC1_RX;
+		else
+			sync_dev = OMAP24XX_DMA_MMC2_RX;
 	} else {
 		host->dma_dir = DMA_TO_DEVICE;
-		sync_dev = OMAP24XX_DMA_MMC1_TX;
+		if (host->id == OMAP_MMC1_DEVID)
+			sync_dev = OMAP24XX_DMA_MMC1_TX;
+		else
+			sync_dev = OMAP24XX_DMA_MMC2_TX;
 	}
 
 	ret = omap_request_dma(sync_dev, "MMC/SD", mmc_omap_dma_cb,
@@ -692,6 +702,7 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
 	struct mmc_omap_host *host = NULL;
 	struct resource *res;
 	int ret = 0, irq;
+	u32 hctl, capa;
 
 	if (pdata == NULL) {
 		dev_err(&pdev->dev, "Platform Data is missing\n");
@@ -778,11 +789,20 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
 	if (pdata->conf.wire4)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
 
+	/* Only MMC1 supports 3.0V */
+	if (host->id == OMAP_MMC1_DEVID) {
+		hctl = SDVS30;
+		capa = VS30 | VS18;
+	} else {
+		hctl = SDVS18;
+		capa = VS18;
+	}
+
 	OMAP_HSMMC_WRITE(host->base, HCTL,
-			OMAP_HSMMC_READ(host->base, HCTL) | SDVS30);
+			OMAP_HSMMC_READ(host->base, HCTL) | hctl);
 
-	OMAP_HSMMC_WRITE(host->base, CAPA, OMAP_HSMMC_READ(host->base,
-							CAPA) | VS30 | VS18);
+	OMAP_HSMMC_WRITE(host->base, CAPA,
+			OMAP_HSMMC_READ(host->base, CAPA) | capa);
 
 	/* Set the controller to AUTO IDLE mode */
 	OMAP_HSMMC_WRITE(host->base, SYSCONFIG,