From: Jiri Slaby Date: Thu, 7 Feb 2008 08:16:46 +0000 (-0800) Subject: Char: mxser, remove it X-Git-Tag: v2.6.25-rc1~305 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=1c45607ad3eb7397bc2433f3c36a4ed8b315889e;p=linux-2.6-omap-h63xx.git Char: mxser, remove it (Old) mxser is obsoleted by mxser_new and scheduled for removal on Dec 2007. Remove it by renaming mxser_new to mxser. Signed-off-by: Jiri Slaby Reviewed-by: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 68ce1300a36..17b1659bd3f 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -6,14 +6,6 @@ be removed from this file. --------------------------- -What: MXSER -When: December 2007 -Why: Old mxser driver is obsoleted by the mxser_new. Give it some time yet - and remove it. -Who: Jiri Slaby - ---------------------------- - What: dev->power.power_state When: July 2007 Why: Broken design for runtime control over driver power states, confusing diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig index 85bf9b2aa74..7927fd0faca 100644 --- a/drivers/char/Kconfig +++ b/drivers/char/Kconfig @@ -194,17 +194,6 @@ config MOXA_INTELLIO module will be called moxa. config MOXA_SMARTIO - tristate "Moxa SmartIO support (OBSOLETE)" - depends on SERIAL_NONSTANDARD - help - Say Y here if you have a Moxa SmartIO multiport serial card. - - This driver can also be built as a module ( = code which can be - inserted in and removed from the running kernel whenever you want). - The module will be called mxser. If you want to do that, say M - here. - -config MOXA_SMARTIO_NEW tristate "Moxa SmartIO support v. 2.0" depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA) help @@ -215,7 +204,7 @@ config MOXA_SMARTIO_NEW changes finally resulting in PCI probing. This driver can also be built as a module. The module will be called - mxser_new. If you want to do that, say M here. + mxser. If you want to do that, say M here. config ISI tristate "Multi-Tech multiport card support (EXPERIMENTAL)" diff --git a/drivers/char/Makefile b/drivers/char/Makefile index 96fc01eddef..4396e37b3d0 100644 --- a/drivers/char/Makefile +++ b/drivers/char/Makefile @@ -33,7 +33,6 @@ obj-$(CONFIG_MOXA_INTELLIO) += moxa.o obj-$(CONFIG_A2232) += ser_a2232.o generic_serial.o obj-$(CONFIG_ATARI_DSP56K) += dsp56k.o obj-$(CONFIG_MOXA_SMARTIO) += mxser.o -obj-$(CONFIG_MOXA_SMARTIO_NEW) += mxser_new.o obj-$(CONFIG_COMPUTONE) += ip2/ obj-$(CONFIG_RISCOM8) += riscom8.o obj-$(CONFIG_ISI) += isicom.o diff --git a/drivers/char/mxser.c b/drivers/char/mxser.c index 35ff7a24554..dd1b0ab4b31 100644 --- a/drivers/char/mxser.c +++ b/drivers/char/mxser.c @@ -1,41 +1,24 @@ /* * mxser.c -- MOXA Smartio/Industio family multiport serial driver. * - * Copyright (C) 1999-2001 Moxa Technologies (support@moxa.com.tw). + * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com.tw). + * Copyright (C) 2006-2007 Jiri Slaby * - * This code is loosely based on the Linux serial driver, written by - * Linus Torvalds, Theodore T'so and others. + * This code is loosely based on the 1.8 moxa driver which is based on + * Linux serial driver, written by Linus Torvalds, Theodore T'so and + * others. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Original release 10/26/00 - * - * 02/06/01 Support MOXA Industio family boards. - * 02/06/01 Support TIOCGICOUNT. - * 02/06/01 Fix the problem for connecting to serial mouse. - * 02/06/01 Fix the problem for H/W flow control. - * 02/06/01 Fix the compling warning when CONFIG_PCI - * don't be defined. - * * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox * . The original 1.8 code is available on www.moxa.com. * - Fixed x86_64 cleanness * - Fixed sleep with spinlock held in mxser_send_break */ - #include #include #include @@ -64,30 +47,36 @@ #include "mxser.h" -#define MXSER_VERSION "1.8" +#define MXSER_VERSION "2.0.2" /* 1.10 */ #define MXSERMAJOR 174 #define MXSERCUMAJOR 175 -#define MXSER_EVENT_TXLOW 1 -#define MXSER_EVENT_HANGUP 2 - #define MXSER_BOARDS 4 /* Max. boards */ -#define MXSER_PORTS 32 /* Max. ports */ #define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */ -#define MXSER_ISR_PASS_LIMIT 256 +#define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD) +#define MXSER_ISR_PASS_LIMIT 100 #define MXSER_ERR_IOADDR -1 #define MXSER_ERR_IRQ -2 #define MXSER_ERR_IRQ_CONFLIT -3 #define MXSER_ERR_VECTOR -4 +/*CheckIsMoxaMust return value*/ +#define MOXA_OTHER_UART 0x00 +#define MOXA_MUST_MU150_HWID 0x01 +#define MOXA_MUST_MU860_HWID 0x02 + #define WAKEUP_CHARS 256 #define UART_MCR_AFE 0x20 #define UART_LSR_SPECIAL 0x1E +#define PCI_DEVICE_ID_CB108 0x1080 +#define PCI_DEVICE_ID_CB114 0x1142 +#define PCI_DEVICE_ID_CB134I 0x1341 +#define PCI_DEVICE_ID_CP138U 0x1380 +#define PCI_DEVICE_ID_POS104UL 0x1044 -#define IRQ_T(info) ((info->flags & ASYNC_SHARE_IRQ) ? IRQF_SHARED : IRQF_DISABLED) #define C168_ASIC_ID 1 #define C104_ASIC_ID 2 @@ -96,88 +85,11 @@ #define CI134_ASIC_ID 3 #define CI104J_ASIC_ID 5 -enum { - MXSER_BOARD_C168_ISA = 1, - MXSER_BOARD_C104_ISA, - MXSER_BOARD_CI104J, - MXSER_BOARD_C168_PCI, - MXSER_BOARD_C104_PCI, - MXSER_BOARD_C102_ISA, - MXSER_BOARD_CI132, - MXSER_BOARD_CI134, - MXSER_BOARD_CP132, - MXSER_BOARD_CP114, - MXSER_BOARD_CT114, - MXSER_BOARD_CP102, - MXSER_BOARD_CP104U, - MXSER_BOARD_CP168U, - MXSER_BOARD_CP132U, - MXSER_BOARD_CP134U, - MXSER_BOARD_CP104JU, - MXSER_BOARD_RC7000, - MXSER_BOARD_CP118U, - MXSER_BOARD_CP102UL, - MXSER_BOARD_CP102U, -}; - -static char *mxser_brdname[] = { - "C168 series", - "C104 series", - "CI-104J series", - "C168H/PCI series", - "C104H/PCI series", - "C102 series", - "CI-132 series", - "CI-134 series", - "CP-132 series", - "CP-114 series", - "CT-114 series", - "CP-102 series", - "CP-104U series", - "CP-168U series", - "CP-132U series", - "CP-134U series", - "CP-104JU series", - "Moxa UC7000 Serial", - "CP-118U series", - "CP-102UL series", - "CP-102U series", -}; - -static int mxser_numports[] = { - 8, /* C168-ISA */ - 4, /* C104-ISA */ - 4, /* CI104J */ - 8, /* C168-PCI */ - 4, /* C104-PCI */ - 2, /* C102-ISA */ - 2, /* CI132 */ - 4, /* CI134 */ - 2, /* CP132 */ - 4, /* CP114 */ - 4, /* CT114 */ - 2, /* CP102 */ - 4, /* CP104U */ - 8, /* CP168U */ - 2, /* CP132U */ - 4, /* CP134U */ - 4, /* CP104JU */ - 8, /* RC7000 */ - 8, /* CP118U */ - 2, /* CP102UL */ - 2, /* CP102U */ -}; - -#define UART_TYPE_NUM 2 - -static const unsigned int Gmoxa_uart_id[UART_TYPE_NUM] = { - MOXA_MUST_MU150_HWID, - MOXA_MUST_MU860_HWID -}; +#define MXSER_HIGHBAUD 1 +#define MXSER_HAS2 2 /* This is only for PCI */ -#define UART_INFO_NUM 3 -struct mxpciuart_info { +static const struct { int type; int tx_fifo; int rx_fifo; @@ -186,51 +98,83 @@ struct mxpciuart_info { int rx_trigger; int rx_low_water; long max_baud; -}; - -static const struct mxpciuart_info Gpci_uart_info[UART_INFO_NUM] = { +} Gpci_uart_info[] = { {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L}, {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L}, {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L} }; +#define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info) +struct mxser_cardinfo { + char *name; + unsigned int nports; + unsigned int flags; +}; -#ifdef CONFIG_PCI +static const struct mxser_cardinfo mxser_cards[] = { +/* 0*/ { "C168 series", 8, }, + { "C104 series", 4, }, + { "CI-104J series", 4, }, + { "C168H/PCI series", 8, }, + { "C104H/PCI series", 4, }, +/* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */ + { "CI-132 series", 4, MXSER_HAS2 }, + { "CI-134 series", 4, }, + { "CP-132 series", 2, }, + { "CP-114 series", 4, }, +/*10*/ { "CT-114 series", 4, }, + { "CP-102 series", 2, MXSER_HIGHBAUD }, + { "CP-104U series", 4, }, + { "CP-168U series", 8, }, + { "CP-132U series", 2, }, +/*15*/ { "CP-134U series", 4, }, + { "CP-104JU series", 4, }, + { "Moxa UC7000 Serial", 8, }, /* RC7000 */ + { "CP-118U series", 8, }, + { "CP-102UL series", 2, }, +/*20*/ { "CP-102U series", 2, }, + { "CP-118EL series", 8, }, + { "CP-168EL series", 8, }, + { "CP-104EL series", 4, }, + { "CB-108 series", 8, }, +/*25*/ { "CB-114 series", 4, }, + { "CB-134I series", 4, }, + { "CP-138U series", 8, }, + { "POS-104UL series", 4, } +}; +/* driver_data correspond to the lines in the structure above + see also ISA probe function before you change something */ static struct pci_device_id mxser_pcibrds[] = { - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_C168, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_C168_PCI}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_C104, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_C104_PCI}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP132, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP132}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP114}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CT114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CT114}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP102, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP102}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP104U, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP104U}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP168U, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP168U}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP132U, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP132U}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP134U, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP134U}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP104JU, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP104JU}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_RC7000, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_RC7000}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP118U, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP118U}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP102UL, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP102UL}, - {PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_CP102U, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MXSER_BOARD_CP102U}, - {0} + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 }, + { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 }, + { } }; - MODULE_DEVICE_TABLE(pci, mxser_pcibrds); - -#endif - -typedef struct _moxa_pci_info { - unsigned short busNum; - unsigned short devNum; - struct pci_dev *pdev; /* add by Victor Yu. 06-23-2003 */ -} moxa_pci_info; - static int ioaddr[MXSER_BOARDS] = { 0, 0, 0, 0 }; static int ttymajor = MXSERMAJOR; -static int calloutmajor = MXSERCUMAJOR; -static int verbose = 0; /* Variables for insmod */ @@ -238,8 +182,6 @@ MODULE_AUTHOR("Casper Yang"); MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver"); module_param_array(ioaddr, int, NULL, 0); module_param(ttymajor, int, 0); -module_param(calloutmajor, int, 0); -module_param(verbose, bool, 0); MODULE_LICENSE("GPL"); struct mxser_log { @@ -274,67 +216,69 @@ struct mxser_mon_ext { int iftype[32]; }; -struct mxser_hwconf { - int board_type; - int ports; - int irq; - int vector; - int vector_mask; - int uart_type; - int ioaddr[MXSER_PORTS_PER_BOARD]; - int baud_base[MXSER_PORTS_PER_BOARD]; - moxa_pci_info pciInfo; - int IsMoxaMustChipFlag; /* add by Victor Yu. 08-30-2002 */ - int MaxCanSetBaudRate[MXSER_PORTS_PER_BOARD]; /* add by Victor Yu. 09-04-2002 */ - int opmode_ioaddr[MXSER_PORTS_PER_BOARD]; /* add by Victor Yu. 01-05-2004 */ -}; +struct mxser_board; + +struct mxser_port { + struct mxser_board *board; + struct tty_struct *tty; + + unsigned long ioaddr; + unsigned long opmode_ioaddr; + int max_baud; -struct mxser_struct { - int port; - int base; /* port base address */ - int irq; /* port using irq no. */ - int vector; /* port irq vector */ - int vectormask; /* port vector mask */ int rx_high_water; int rx_trigger; /* Rx fifo trigger level */ int rx_low_water; int baud_base; /* max. speed */ - int flags; /* defined in tty.h */ int type; /* UART type */ - struct tty_struct *tty; - int read_status_mask; - int ignore_status_mask; - int xmit_fifo_size; - int custom_divisor; + int flags; /* defined in tty.h */ + int x_char; /* xon/xoff character */ - int close_delay; - unsigned short closing_wait; int IER; /* Interrupt Enable Register */ int MCR; /* Modem control register */ + + unsigned char stop_rx; + unsigned char ldisc_stop_rx; + + int custom_divisor; + int close_delay; + unsigned short closing_wait; + unsigned char err_shadow; unsigned long event; + int count; /* # of fd on device */ int blocked_open; /* # of blocked opens */ + struct async_icount icount; /* kernel counters for 4 input interrupts */ + int timeout; + + int read_status_mask; + int ignore_status_mask; + int xmit_fifo_size; unsigned char *xmit_buf; int xmit_head; int xmit_tail; int xmit_cnt; - struct work_struct tqueue; + struct ktermios normal_termios; - struct ktermios callout_termios; - wait_queue_head_t open_wait; - wait_queue_head_t close_wait; - wait_queue_head_t delta_msr_wait; - struct async_icount icount; /* kernel counters for the 4 input interrupts */ - int timeout; - int IsMoxaMustChipFlag; /* add by Victor Yu. 08-30-2002 */ - int MaxCanSetBaudRate; /* add by Victor Yu. 09-04-2002 */ - int opmode_ioaddr; /* add by Victor Yu. 01-05-2004 */ - unsigned char stop_rx; - unsigned char ldisc_stop_rx; - long realbaud; + struct mxser_mon mon_data; - unsigned char err_shadow; + spinlock_t slock; + wait_queue_head_t open_wait; + wait_queue_head_t delta_msr_wait; +}; + +struct mxser_board { + unsigned int idx; + int irq; + const struct mxser_cardinfo *info; + unsigned long vector; + unsigned long vector_mask; + + int chip_flag; + int uart_type; + + struct mxser_port ports[MXSER_PORTS_PER_BOARD]; }; struct mxser_mstatus { @@ -352,73 +296,16 @@ static int mxserBoardCAP[MXSER_BOARDS] = { /* 0x180, 0x280, 0x200, 0x320 */ }; +static struct mxser_board mxser_boards[MXSER_BOARDS]; static struct tty_driver *mxvar_sdriver; -static struct mxser_struct mxvar_table[MXSER_PORTS]; -static struct tty_struct *mxvar_tty[MXSER_PORTS + 1]; -static struct ktermios *mxvar_termios[MXSER_PORTS + 1]; -static struct ktermios *mxvar_termios_locked[MXSER_PORTS + 1]; static struct mxser_log mxvar_log; static int mxvar_diagflag; static unsigned char mxser_msr[MXSER_PORTS + 1]; static struct mxser_mon_ext mon_data_ext; static int mxser_set_baud_method[MXSER_PORTS + 1]; -static spinlock_t gm_lock; - -/* - * This is used to figure out the divisor speeds and the timeouts - */ - -static struct mxser_hwconf mxsercfg[MXSER_BOARDS]; - -/* - * static functions: - */ - -static void mxser_getcfg(int board, struct mxser_hwconf *hwconf); -static int mxser_init(void); - -/* static void mxser_poll(unsigned long); */ -static int mxser_get_ISA_conf(int, struct mxser_hwconf *); -static void mxser_do_softint(struct work_struct *); -static int mxser_open(struct tty_struct *, struct file *); -static void mxser_close(struct tty_struct *, struct file *); -static int mxser_write(struct tty_struct *, const unsigned char *, int); -static int mxser_write_room(struct tty_struct *); -static void mxser_flush_buffer(struct tty_struct *); -static int mxser_chars_in_buffer(struct tty_struct *); -static void mxser_flush_chars(struct tty_struct *); -static void mxser_put_char(struct tty_struct *, unsigned char); -static int mxser_ioctl(struct tty_struct *, struct file *, uint, ulong); -static int mxser_ioctl_special(unsigned int, void __user *); -static void mxser_throttle(struct tty_struct *); -static void mxser_unthrottle(struct tty_struct *); -static void mxser_set_termios(struct tty_struct *, struct ktermios *); -static void mxser_stop(struct tty_struct *); -static void mxser_start(struct tty_struct *); -static void mxser_hangup(struct tty_struct *); -static void mxser_rs_break(struct tty_struct *, int); -static irqreturn_t mxser_interrupt(int, void *); -static void mxser_receive_chars(struct mxser_struct *, int *); -static void mxser_transmit_chars(struct mxser_struct *); -static void mxser_check_modem_status(struct mxser_struct *, int); -static int mxser_block_til_ready(struct tty_struct *, struct file *, struct mxser_struct *); -static int mxser_startup(struct mxser_struct *); -static void mxser_shutdown(struct mxser_struct *); -static int mxser_change_speed(struct mxser_struct *, struct ktermios *old_termios); -static int mxser_get_serial_info(struct mxser_struct *, struct serial_struct __user *); -static int mxser_set_serial_info(struct mxser_struct *, struct serial_struct __user *); -static int mxser_get_lsr_info(struct mxser_struct *, unsigned int __user *); -static void mxser_send_break(struct mxser_struct *, int); -static int mxser_tiocmget(struct tty_struct *, struct file *); -static int mxser_tiocmset(struct tty_struct *, struct file *, unsigned int, unsigned int); -static int mxser_set_baud(struct mxser_struct *info, long newspd); -static void mxser_wait_until_sent(struct tty_struct *tty, int timeout); - -static void mxser_startrx(struct tty_struct *tty); -static void mxser_stoprx(struct tty_struct *tty); #ifdef CONFIG_PCI -static int CheckIsMoxaMust(int io) +static int __devinit CheckIsMoxaMust(unsigned long io) { u8 oldmcr, hwid; int i; @@ -434,90 +321,15 @@ static int CheckIsMoxaMust(int io) } GET_MOXA_MUST_HARDWARE_ID(io, &hwid); - for (i = 0; i < UART_TYPE_NUM; i++) { - if (hwid == Gmoxa_uart_id[i]) + for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */ + if (hwid == Gpci_uart_info[i].type) return (int)hwid; } return MOXA_OTHER_UART; } #endif -/* above is modified by Victor Yu. 08-15-2002 */ - -static const struct tty_operations mxser_ops = { - .open = mxser_open, - .close = mxser_close, - .write = mxser_write, - .put_char = mxser_put_char, - .flush_chars = mxser_flush_chars, - .write_room = mxser_write_room, - .chars_in_buffer = mxser_chars_in_buffer, - .flush_buffer = mxser_flush_buffer, - .ioctl = mxser_ioctl, - .throttle = mxser_throttle, - .unthrottle = mxser_unthrottle, - .set_termios = mxser_set_termios, - .stop = mxser_stop, - .start = mxser_start, - .hangup = mxser_hangup, - .break_ctl = mxser_rs_break, - .wait_until_sent = mxser_wait_until_sent, - .tiocmget = mxser_tiocmget, - .tiocmset = mxser_tiocmset, -}; - -/* - * The MOXA Smartio/Industio serial driver boot-time initialization code! - */ - -static int __init mxser_module_init(void) -{ - int ret; - - if (verbose) - printk(KERN_DEBUG "Loading module mxser ...\n"); - ret = mxser_init(); - if (verbose) - printk(KERN_DEBUG "Done.\n"); - return ret; -} - -static void __exit mxser_module_exit(void) -{ - int i, err; - - if (verbose) - printk(KERN_DEBUG "Unloading module mxser ...\n"); - - err = tty_unregister_driver(mxvar_sdriver); - if (!err) - put_tty_driver(mxvar_sdriver); - else - printk(KERN_ERR "Couldn't unregister MOXA Smartio/Industio family serial driver\n"); - - for (i = 0; i < MXSER_BOARDS; i++) { - struct pci_dev *pdev; - - if (mxsercfg[i].board_type == -1) - continue; - else { - pdev = mxsercfg[i].pciInfo.pdev; - free_irq(mxsercfg[i].irq, &mxvar_table[i * MXSER_PORTS_PER_BOARD]); - if (pdev != NULL) { /* PCI */ - release_region(pci_resource_start(pdev, 2), pci_resource_len(pdev, 2)); - release_region(pci_resource_start(pdev, 3), pci_resource_len(pdev, 3)); - pci_dev_put(pdev); - } else { - release_region(mxsercfg[i].ioaddr[0], 8 * mxsercfg[i].ports); - release_region(mxsercfg[i].vector, 1); - } - } - } - if (verbose) - printk(KERN_DEBUG "Done.\n"); -} - -static void process_txrx_fifo(struct mxser_struct *info) +static void process_txrx_fifo(struct mxser_port *info) { int i; @@ -526,476 +338,586 @@ static void process_txrx_fifo(struct mxser_struct *info) info->rx_high_water = 1; info->rx_low_water = 1; info->xmit_fifo_size = 1; - } else { - for (i = 0; i < UART_INFO_NUM; i++) { - if (info->IsMoxaMustChipFlag == Gpci_uart_info[i].type) { + } else + for (i = 0; i < UART_INFO_NUM; i++) + if (info->board->chip_flag == Gpci_uart_info[i].type) { info->rx_trigger = Gpci_uart_info[i].rx_trigger; info->rx_low_water = Gpci_uart_info[i].rx_low_water; info->rx_high_water = Gpci_uart_info[i].rx_high_water; info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size; break; } - } - } } -static int mxser_initbrd(int board, struct mxser_hwconf *hwconf) +static unsigned char mxser_get_msr(int baseaddr, int mode, int port) { - struct mxser_struct *info; - int retval; - int i, n; + unsigned char status = 0; - n = board * MXSER_PORTS_PER_BOARD; - info = &mxvar_table[n]; - /*if (verbose) */ { - printk(KERN_DEBUG " ttyMI%d - ttyMI%d ", - n, n + hwconf->ports - 1); - printk(" max. baud rate = %d bps.\n", - hwconf->MaxCanSetBaudRate[0]); - } - - for (i = 0; i < hwconf->ports; i++, n++, info++) { - info->port = n; - info->base = hwconf->ioaddr[i]; - info->irq = hwconf->irq; - info->vector = hwconf->vector; - info->vectormask = hwconf->vector_mask; - info->opmode_ioaddr = hwconf->opmode_ioaddr[i]; /* add by Victor Yu. 01-05-2004 */ - info->stop_rx = 0; - info->ldisc_stop_rx = 0; + status = inb(baseaddr + UART_MSR); - info->IsMoxaMustChipFlag = hwconf->IsMoxaMustChipFlag; - /* Enhance mode enabled here */ - if (info->IsMoxaMustChipFlag != MOXA_OTHER_UART) { - ENABLE_MOXA_MUST_ENCHANCE_MODE(info->base); - } + mxser_msr[port] &= 0x0F; + mxser_msr[port] |= status; + status = mxser_msr[port]; + if (mode) + mxser_msr[port] = 0; - info->flags = ASYNC_SHARE_IRQ; - info->type = hwconf->uart_type; - info->baud_base = hwconf->baud_base[i]; + return status; +} - info->MaxCanSetBaudRate = hwconf->MaxCanSetBaudRate[i]; +static int mxser_block_til_ready(struct tty_struct *tty, struct file *filp, + struct mxser_port *port) +{ + DECLARE_WAITQUEUE(wait, current); + int retval; + int do_clocal = 0; + unsigned long flags; - process_txrx_fifo(info); + /* + * If non-blocking mode is set, or the port is not enabled, + * then make the check up front and then exit. + */ + if ((filp->f_flags & O_NONBLOCK) || + test_bit(TTY_IO_ERROR, &tty->flags)) { + port->flags |= ASYNC_NORMAL_ACTIVE; + return 0; + } + if (tty->termios->c_cflag & CLOCAL) + do_clocal = 1; - info->custom_divisor = hwconf->baud_base[i] * 16; - info->close_delay = 5 * HZ / 10; - info->closing_wait = 30 * HZ; - INIT_WORK(&info->tqueue, mxser_do_softint); - info->normal_termios = mxvar_sdriver->init_termios; - init_waitqueue_head(&info->open_wait); - init_waitqueue_head(&info->close_wait); - init_waitqueue_head(&info->delta_msr_wait); - memset(&info->mon_data, 0, sizeof(struct mxser_mon)); - info->err_shadow = 0; - spin_lock_init(&info->slock); - } /* - * Allocate the IRQ if necessary + * Block waiting for the carrier detect and the line to become + * free (i.e., not in use by the callout). While we are in + * this loop, port->count is dropped by one, so that + * mxser_close() knows when to free things. We restore it upon + * exit, either normal or abnormal. */ + retval = 0; + add_wait_queue(&port->open_wait, &wait); - - /* before set INT ISR, disable all int */ - for (i = 0; i < hwconf->ports; i++) { - outb(inb(hwconf->ioaddr[i] + UART_IER) & 0xf0, - hwconf->ioaddr[i] + UART_IER); + spin_lock_irqsave(&port->slock, flags); + if (!tty_hung_up_p(filp)) + port->count--; + spin_unlock_irqrestore(&port->slock, flags); + port->blocked_open++; + while (1) { + spin_lock_irqsave(&port->slock, flags); + outb(inb(port->ioaddr + UART_MCR) | + UART_MCR_DTR | UART_MCR_RTS, port->ioaddr + UART_MCR); + spin_unlock_irqrestore(&port->slock, flags); + set_current_state(TASK_INTERRUPTIBLE); + if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) { + if (port->flags & ASYNC_HUP_NOTIFY) + retval = -EAGAIN; + else + retval = -ERESTARTSYS; + break; + } + if (!(port->flags & ASYNC_CLOSING) && + (do_clocal || + (inb(port->ioaddr + UART_MSR) & UART_MSR_DCD))) + break; + if (signal_pending(current)) { + retval = -ERESTARTSYS; + break; + } + schedule(); } - - n = board * MXSER_PORTS_PER_BOARD; - info = &mxvar_table[n]; - - retval = request_irq(hwconf->irq, mxser_interrupt, IRQ_T(info), - "mxser", info); - if (retval) { - printk(KERN_ERR "Board %d: %s", - board, mxser_brdname[hwconf->board_type - 1]); - printk(" Request irq failed, IRQ (%d) may conflict with" - " another device.\n", info->irq); + set_current_state(TASK_RUNNING); + remove_wait_queue(&port->open_wait, &wait); + if (!tty_hung_up_p(filp)) + port->count++; + port->blocked_open--; + if (retval) return retval; - } + port->flags |= ASYNC_NORMAL_ACTIVE; return 0; } -static void mxser_getcfg(int board, struct mxser_hwconf *hwconf) +static int mxser_set_baud(struct mxser_port *info, long newspd) { - mxsercfg[board] = *hwconf; -} + int quot = 0, baud; + unsigned char cval; -#ifdef CONFIG_PCI -static int mxser_get_PCI_conf(int busnum, int devnum, int board_type, struct mxser_hwconf *hwconf) -{ - int i, j; - /* unsigned int val; */ - unsigned int ioaddress; - struct pci_dev *pdev = hwconf->pciInfo.pdev; + if (!info->tty || !info->tty->termios) + return -1; - /* io address */ - hwconf->board_type = board_type; - hwconf->ports = mxser_numports[board_type - 1]; - ioaddress = pci_resource_start(pdev, 2); - request_region(pci_resource_start(pdev, 2), pci_resource_len(pdev, 2), - "mxser(IO)"); + if (!(info->ioaddr)) + return -1; - for (i = 0; i < hwconf->ports; i++) - hwconf->ioaddr[i] = ioaddress + 8 * i; + if (newspd > info->max_baud) + return -1; - /* vector */ - ioaddress = pci_resource_start(pdev, 3); - request_region(pci_resource_start(pdev, 3), pci_resource_len(pdev, 3), - "mxser(vector)"); - hwconf->vector = ioaddress; + if (newspd == 134) { + quot = 2 * info->baud_base / 269; + tty_encode_baud_rate(info->tty, 134, 134); + } else if (newspd) { + quot = info->baud_base / newspd; + if (quot == 0) + quot = 1; + baud = info->baud_base/quot; + tty_encode_baud_rate(info->tty, baud, baud); + } else { + quot = 0; + } - /* irq */ - hwconf->irq = hwconf->pciInfo.pdev->irq; + info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base); + info->timeout += HZ / 50; /* Add .02 seconds of slop */ - hwconf->IsMoxaMustChipFlag = CheckIsMoxaMust(hwconf->ioaddr[0]); - hwconf->uart_type = PORT_16550A; - hwconf->vector_mask = 0; + if (quot) { + info->MCR |= UART_MCR_DTR; + outb(info->MCR, info->ioaddr + UART_MCR); + } else { + info->MCR &= ~UART_MCR_DTR; + outb(info->MCR, info->ioaddr + UART_MCR); + return 0; + } + cval = inb(info->ioaddr + UART_LCR); - for (i = 0; i < hwconf->ports; i++) { - for (j = 0; j < UART_INFO_NUM; j++) { - if (Gpci_uart_info[j].type == hwconf->IsMoxaMustChipFlag) { - hwconf->MaxCanSetBaudRate[i] = Gpci_uart_info[j].max_baud; + outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */ - /* exception....CP-102 */ - if (board_type == MXSER_BOARD_CP102) - hwconf->MaxCanSetBaudRate[i] = 921600; - break; - } - } - } + outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */ + outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */ + outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */ - if (hwconf->IsMoxaMustChipFlag == MOXA_MUST_MU860_HWID) { - for (i = 0; i < hwconf->ports; i++) { - if (i < 4) - hwconf->opmode_ioaddr[i] = ioaddress + 4; - else - hwconf->opmode_ioaddr[i] = ioaddress + 0x0c; - } - outb(0, ioaddress + 4); /* default set to RS232 mode */ - outb(0, ioaddress + 0x0c); /* default set to RS232 mode */ - } +#ifdef BOTHER + if (C_BAUD(info->tty) == BOTHER) { + quot = info->baud_base % newspd; + quot *= 8; + if (quot % newspd > newspd / 2) { + quot /= newspd; + quot++; + } else + quot /= newspd; + + SET_MOXA_MUST_ENUM_VALUE(info->ioaddr, quot); + } else +#endif + SET_MOXA_MUST_ENUM_VALUE(info->ioaddr, 0); - for (i = 0; i < hwconf->ports; i++) { - hwconf->vector_mask |= (1 << i); - hwconf->baud_base[i] = 921600; - } return 0; } -#endif -static int mxser_init(void) +/* + * This routine is called to set the UART divisor registers to match + * the specified baud rate for a serial port. + */ +static int mxser_change_speed(struct mxser_port *info, + struct ktermios *old_termios) { - int i, m, retval, b, n; - struct pci_dev *pdev = NULL; - int index; - unsigned char busnum, devnum; - struct mxser_hwconf hwconf; + unsigned cflag, cval, fcr; + int ret = 0; + unsigned char status; - mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1); - if (!mxvar_sdriver) - return -ENOMEM; - spin_lock_init(&gm_lock); - - for (i = 0; i < MXSER_BOARDS; i++) { - mxsercfg[i].board_type = -1; - } - - printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n", - MXSER_VERSION); - - /* Initialize the tty_driver structure */ - memset(mxvar_sdriver, 0, sizeof(struct tty_driver)); - mxvar_sdriver->owner = THIS_MODULE; - mxvar_sdriver->magic = TTY_DRIVER_MAGIC; - mxvar_sdriver->name = "ttyMI"; - mxvar_sdriver->major = ttymajor; - mxvar_sdriver->minor_start = 0; - mxvar_sdriver->num = MXSER_PORTS + 1; - mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL; - mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL; - mxvar_sdriver->init_termios = tty_std_termios; - mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL; - mxvar_sdriver->init_termios.c_ispeed = 9600; - mxvar_sdriver->init_termios.c_ospeed = 9600; - mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW; - tty_set_operations(mxvar_sdriver, &mxser_ops); - mxvar_sdriver->ttys = mxvar_tty; - mxvar_sdriver->termios = mxvar_termios; - mxvar_sdriver->termios_locked = mxvar_termios_locked; + if (!info->tty || !info->tty->termios) + return ret; + cflag = info->tty->termios->c_cflag; + if (!(info->ioaddr)) + return ret; - mxvar_diagflag = 0; - memset(mxvar_table, 0, MXSER_PORTS * sizeof(struct mxser_struct)); - memset(&mxvar_log, 0, sizeof(struct mxser_log)); + if (mxser_set_baud_method[info->tty->index] == 0) + mxser_set_baud(info, tty_get_baud_rate(info->tty)); - memset(&mxser_msr, 0, sizeof(unsigned char) * (MXSER_PORTS + 1)); - memset(&mon_data_ext, 0, sizeof(struct mxser_mon_ext)); - memset(&mxser_set_baud_method, 0, sizeof(int) * (MXSER_PORTS + 1)); - memset(&hwconf, 0, sizeof(struct mxser_hwconf)); + /* byte size and parity */ + switch (cflag & CSIZE) { + case CS5: + cval = 0x00; + break; + case CS6: + cval = 0x01; + break; + case CS7: + cval = 0x02; + break; + case CS8: + cval = 0x03; + break; + default: + cval = 0x00; + break; /* too keep GCC shut... */ + } + if (cflag & CSTOPB) + cval |= 0x04; + if (cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(cflag & PARODD)) + cval |= UART_LCR_EPAR; + if (cflag & CMSPAR) + cval |= UART_LCR_SPAR; - m = 0; - /* Start finding ISA boards here */ - for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) { - int cap; - - if (!(cap = mxserBoardCAP[b])) - continue; - - retval = mxser_get_ISA_conf(cap, &hwconf); - - if (retval != 0) - printk(KERN_INFO "Found MOXA %s board (CAP=0x%x)\n", - mxser_brdname[hwconf.board_type - 1], ioaddr[b]); - - if (retval <= 0) { - if (retval == MXSER_ERR_IRQ) - printk(KERN_ERR "Invalid interrupt number, " - "board not configured\n"); - else if (retval == MXSER_ERR_IRQ_CONFLIT) - printk(KERN_ERR "Invalid interrupt number, " - "board not configured\n"); - else if (retval == MXSER_ERR_VECTOR) - printk(KERN_ERR "Invalid interrupt vector, " - "board not configured\n"); - else if (retval == MXSER_ERR_IOADDR) - printk(KERN_ERR "Invalid I/O address, " - "board not configured\n"); - - continue; + if ((info->type == PORT_8250) || (info->type == PORT_16450)) { + if (info->board->chip_flag) { + fcr = UART_FCR_ENABLE_FIFO; + fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; + SET_MOXA_MUST_FIFO_VALUE(info); + } else + fcr = 0; + } else { + fcr = UART_FCR_ENABLE_FIFO; + if (info->board->chip_flag) { + fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; + SET_MOXA_MUST_FIFO_VALUE(info); + } else { + switch (info->rx_trigger) { + case 1: + fcr |= UART_FCR_TRIGGER_1; + break; + case 4: + fcr |= UART_FCR_TRIGGER_4; + break; + case 8: + fcr |= UART_FCR_TRIGGER_8; + break; + default: + fcr |= UART_FCR_TRIGGER_14; + break; + } } - - hwconf.pciInfo.busNum = 0; - hwconf.pciInfo.devNum = 0; - hwconf.pciInfo.pdev = NULL; - - mxser_getcfg(m, &hwconf); - /* - * init mxsercfg first, - * or mxsercfg data is not correct on ISR. - */ - /* mxser_initbrd will hook ISR. */ - if (mxser_initbrd(m, &hwconf) < 0) - continue; - - m++; } - /* Start finding ISA boards from module arg */ - for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) { - int cap; - - if (!(cap = ioaddr[b])) - continue; - - retval = mxser_get_ISA_conf(cap, &hwconf); - - if (retval != 0) - printk(KERN_INFO "Found MOXA %s board (CAP=0x%x)\n", - mxser_brdname[hwconf.board_type - 1], ioaddr[b]); - - if (retval <= 0) { - if (retval == MXSER_ERR_IRQ) - printk(KERN_ERR "Invalid interrupt number, " - "board not configured\n"); - else if (retval == MXSER_ERR_IRQ_CONFLIT) - printk(KERN_ERR "Invalid interrupt number, " - "board not configured\n"); - else if (retval == MXSER_ERR_VECTOR) - printk(KERN_ERR "Invalid interrupt vector, " - "board not configured\n"); - else if (retval == MXSER_ERR_IOADDR) - printk(KERN_ERR "Invalid I/O address, " - "board not configured\n"); - - continue; + /* CTS flow control flag and modem status interrupts */ + info->IER &= ~UART_IER_MSI; + info->MCR &= ~UART_MCR_AFE; + if (cflag & CRTSCTS) { + info->flags |= ASYNC_CTS_FLOW; + info->IER |= UART_IER_MSI; + if ((info->type == PORT_16550A) || (info->board->chip_flag)) { + info->MCR |= UART_MCR_AFE; + } else { + status = inb(info->ioaddr + UART_MSR); + if (info->tty->hw_stopped) { + if (status & UART_MSR_CTS) { + info->tty->hw_stopped = 0; + if (info->type != PORT_16550A && + !info->board->chip_flag) { + outb(info->IER & ~UART_IER_THRI, + info->ioaddr + + UART_IER); + info->IER |= UART_IER_THRI; + outb(info->IER, info->ioaddr + + UART_IER); + } + tty_wakeup(info->tty); + } + } else { + if (!(status & UART_MSR_CTS)) { + info->tty->hw_stopped = 1; + if ((info->type != PORT_16550A) && + (!info->board->chip_flag)) { + info->IER &= ~UART_IER_THRI; + outb(info->IER, info->ioaddr + + UART_IER); + } + } + } } + } else { + info->flags &= ~ASYNC_CTS_FLOW; + } + outb(info->MCR, info->ioaddr + UART_MCR); + if (cflag & CLOCAL) { + info->flags &= ~ASYNC_CHECK_CD; + } else { + info->flags |= ASYNC_CHECK_CD; + info->IER |= UART_IER_MSI; + } + outb(info->IER, info->ioaddr + UART_IER); + + /* + * Set up parity check flag + */ + info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (I_INPCK(info->tty)) + info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (I_BRKINT(info->tty) || I_PARMRK(info->tty)) + info->read_status_mask |= UART_LSR_BI; - hwconf.pciInfo.busNum = 0; - hwconf.pciInfo.devNum = 0; - hwconf.pciInfo.pdev = NULL; + info->ignore_status_mask = 0; - mxser_getcfg(m, &hwconf); + if (I_IGNBRK(info->tty)) { + info->ignore_status_mask |= UART_LSR_BI; + info->read_status_mask |= UART_LSR_BI; /* - * init mxsercfg first, - * or mxsercfg data is not correct on ISR. + * If we're ignore parity and break indicators, ignore + * overruns too. (For real raw support). */ - /* mxser_initbrd will hook ISR. */ - if (mxser_initbrd(m, &hwconf) < 0) - continue; - - m++; + if (I_IGNPAR(info->tty)) { + info->ignore_status_mask |= + UART_LSR_OE | + UART_LSR_PE | + UART_LSR_FE; + info->read_status_mask |= + UART_LSR_OE | + UART_LSR_PE | + UART_LSR_FE; + } } - - /* start finding PCI board here */ -#ifdef CONFIG_PCI - n = ARRAY_SIZE(mxser_pcibrds) - 1; - index = 0; - b = 0; - while (b < n) { - pdev = pci_get_device(mxser_pcibrds[b].vendor, - mxser_pcibrds[b].device, pdev); - if (pdev == NULL) { - b++; - continue; + if (info->board->chip_flag) { + SET_MOXA_MUST_XON1_VALUE(info->ioaddr, START_CHAR(info->tty)); + SET_MOXA_MUST_XOFF1_VALUE(info->ioaddr, STOP_CHAR(info->tty)); + if (I_IXON(info->tty)) { + ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr); + } else { + DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr); } - hwconf.pciInfo.busNum = busnum = pdev->bus->number; - hwconf.pciInfo.devNum = devnum = PCI_SLOT(pdev->devfn) << 3; - hwconf.pciInfo.pdev = pdev; - printk(KERN_INFO "Found MOXA %s board(BusNo=%d,DevNo=%d)\n", - mxser_brdname[(int) (mxser_pcibrds[b].driver_data) - 1], - busnum, devnum >> 3); - index++; - if (m >= MXSER_BOARDS) - printk(KERN_ERR - "Too many Smartio/Industio family boards find " - "(maximum %d), board not configured\n", - MXSER_BOARDS); - else { - if (pci_enable_device(pdev)) { - printk(KERN_ERR "Moxa SmartI/O PCI enable " - "fail !\n"); - continue; - } - retval = mxser_get_PCI_conf(busnum, devnum, - (int)mxser_pcibrds[b].driver_data, - &hwconf); - if (retval < 0) { - if (retval == MXSER_ERR_IRQ) - printk(KERN_ERR - "Invalid interrupt number, " - "board not configured\n"); - else if (retval == MXSER_ERR_IRQ_CONFLIT) - printk(KERN_ERR - "Invalid interrupt number, " - "board not configured\n"); - else if (retval == MXSER_ERR_VECTOR) - printk(KERN_ERR - "Invalid interrupt vector, " - "board not configured\n"); - else if (retval == MXSER_ERR_IOADDR) - printk(KERN_ERR - "Invalid I/O address, " - "board not configured\n"); - continue; - } - mxser_getcfg(m, &hwconf); - /* init mxsercfg first, - * or mxsercfg data is not correct on ISR. - */ - /* mxser_initbrd will hook ISR. */ - if (mxser_initbrd(m, &hwconf) < 0) - continue; - m++; - /* Keep an extra reference if we succeeded. It will - be returned at unload time */ - pci_dev_get(pdev); + if (I_IXOFF(info->tty)) { + ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr); + } else { + DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr); } } -#endif - retval = tty_register_driver(mxvar_sdriver); - if (retval) { - printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family" - " driver !\n"); - put_tty_driver(mxvar_sdriver); - for (i = 0; i < MXSER_BOARDS; i++) { - if (mxsercfg[i].board_type == -1) - continue; - else { - free_irq(mxsercfg[i].irq, &mxvar_table[i * MXSER_PORTS_PER_BOARD]); - /* todo: release io, vector */ - } - } - return retval; - } + outb(fcr, info->ioaddr + UART_FCR); /* set fcr */ + outb(cval, info->ioaddr + UART_LCR); - return 0; + return ret; } -static void mxser_do_softint(struct work_struct *work) +static void mxser_check_modem_status(struct mxser_port *port, int status) { - struct mxser_struct *info = - container_of(work, struct mxser_struct, tqueue); - struct tty_struct *tty; + /* update input line counters */ + if (status & UART_MSR_TERI) + port->icount.rng++; + if (status & UART_MSR_DDSR) + port->icount.dsr++; + if (status & UART_MSR_DDCD) + port->icount.dcd++; + if (status & UART_MSR_DCTS) + port->icount.cts++; + port->mon_data.modem_status = status; + wake_up_interruptible(&port->delta_msr_wait); - tty = info->tty; + if ((port->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) { + if (status & UART_MSR_DCD) + wake_up_interruptible(&port->open_wait); + } - if (tty) { - if (test_and_clear_bit(MXSER_EVENT_TXLOW, &info->event)) - tty_wakeup(tty); - if (test_and_clear_bit(MXSER_EVENT_HANGUP, &info->event)) - tty_hangup(tty); + if (port->flags & ASYNC_CTS_FLOW) { + if (port->tty->hw_stopped) { + if (status & UART_MSR_CTS) { + port->tty->hw_stopped = 0; + + if ((port->type != PORT_16550A) && + (!port->board->chip_flag)) { + outb(port->IER & ~UART_IER_THRI, + port->ioaddr + UART_IER); + port->IER |= UART_IER_THRI; + outb(port->IER, port->ioaddr + + UART_IER); + } + tty_wakeup(port->tty); + } + } else { + if (!(status & UART_MSR_CTS)) { + port->tty->hw_stopped = 1; + if (port->type != PORT_16550A && + !port->board->chip_flag) { + port->IER &= ~UART_IER_THRI; + outb(port->IER, port->ioaddr + + UART_IER); + } + } + } } } -static unsigned char mxser_get_msr(int baseaddr, int mode, int port, struct mxser_struct *info) +static int mxser_startup(struct mxser_port *info) { - unsigned char status = 0; - - status = inb(baseaddr + UART_MSR); - - mxser_msr[port] &= 0x0F; - mxser_msr[port] |= status; - status = mxser_msr[port]; - if (mode) - mxser_msr[port] = 0; + unsigned long page; + unsigned long flags; - return status; -} + page = __get_free_page(GFP_KERNEL); + if (!page) + return -ENOMEM; -/* - * This routine is called whenever a serial port is opened. It - * enables interrupts for a serial port, linking in its async structure into - * the IRQ chain. It also performs the serial-specific - * initialization for the tty structure. - */ -static int mxser_open(struct tty_struct *tty, struct file *filp) -{ - struct mxser_struct *info; - int retval, line; + spin_lock_irqsave(&info->slock, flags); - /* initialize driver_data in case something fails */ - tty->driver_data = NULL; + if (info->flags & ASYNC_INITIALIZED) { + free_page(page); + spin_unlock_irqrestore(&info->slock, flags); + return 0; + } - line = tty->index; - if (line == MXSER_PORTS) + if (!info->ioaddr || !info->type) { + if (info->tty) + set_bit(TTY_IO_ERROR, &info->tty->flags); + free_page(page); + spin_unlock_irqrestore(&info->slock, flags); return 0; - if (line < 0 || line > MXSER_PORTS) - return -ENODEV; - info = mxvar_table + line; - if (!info->base) - return -ENODEV; + } + if (info->xmit_buf) + free_page(page); + else + info->xmit_buf = (unsigned char *) page; - tty->driver_data = info; - info->tty = tty; /* - * Start up serial port + * Clear the FIFO buffers and disable them + * (they will be reenabled in mxser_change_speed()) */ - retval = mxser_startup(info); - if (retval) - return retval; - - retval = mxser_block_til_ready(tty, filp, info); - if (retval) - return retval; + if (info->board->chip_flag) + outb((UART_FCR_CLEAR_RCVR | + UART_FCR_CLEAR_XMIT | + MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR); + else + outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), + info->ioaddr + UART_FCR); - info->count++; + /* + * At this point there's no way the LSR could still be 0xFF; + * if it is, then bail out, because there's likely no UART + * here. + */ + if (inb(info->ioaddr + UART_LSR) == 0xff) { + spin_unlock_irqrestore(&info->slock, flags); + if (capable(CAP_SYS_ADMIN)) { + if (info->tty) + set_bit(TTY_IO_ERROR, &info->tty->flags); + return 0; + } else + return -ENODEV; + } - if ((info->count == 1) && (info->flags & ASYNC_SPLIT_TERMIOS)) { - if (tty->driver->subtype == SERIAL_TYPE_NORMAL) - *tty->termios = info->normal_termios; - else - *tty->termios = info->callout_termios; - mxser_change_speed(info, NULL); + /* + * Clear the interrupt registers. + */ + (void) inb(info->ioaddr + UART_LSR); + (void) inb(info->ioaddr + UART_RX); + (void) inb(info->ioaddr + UART_IIR); + (void) inb(info->ioaddr + UART_MSR); + + /* + * Now, initialize the UART + */ + outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */ + info->MCR = UART_MCR_DTR | UART_MCR_RTS; + outb(info->MCR, info->ioaddr + UART_MCR); + + /* + * Finally, enable interrupts + */ + info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; + + if (info->board->chip_flag) + info->IER |= MOXA_MUST_IER_EGDAI; + outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */ + + /* + * And clear the interrupt registers again for luck. + */ + (void) inb(info->ioaddr + UART_LSR); + (void) inb(info->ioaddr + UART_RX); + (void) inb(info->ioaddr + UART_IIR); + (void) inb(info->ioaddr + UART_MSR); + + if (info->tty) + clear_bit(TTY_IO_ERROR, &info->tty->flags); + info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; + + /* + * and set the speed of the serial port + */ + mxser_change_speed(info, NULL); + info->flags |= ASYNC_INITIALIZED; + spin_unlock_irqrestore(&info->slock, flags); + + return 0; +} + +/* + * This routine will shutdown a serial port; interrupts maybe disabled, and + * DTR is dropped if the hangup on close termio flag is on. + */ +static void mxser_shutdown(struct mxser_port *info) +{ + unsigned long flags; + + if (!(info->flags & ASYNC_INITIALIZED)) + return; + + spin_lock_irqsave(&info->slock, flags); + + /* + * clear delta_msr_wait queue to avoid mem leaks: we may free the irq + * here so the queue might never be waken up + */ + wake_up_interruptible(&info->delta_msr_wait); + + /* + * Free the IRQ, if necessary + */ + if (info->xmit_buf) { + free_page((unsigned long) info->xmit_buf); + info->xmit_buf = NULL; } + info->IER = 0; + outb(0x00, info->ioaddr + UART_IER); + + if (!info->tty || (info->tty->termios->c_cflag & HUPCL)) + info->MCR &= ~(UART_MCR_DTR | UART_MCR_RTS); + outb(info->MCR, info->ioaddr + UART_MCR); + + /* clear Rx/Tx FIFO's */ + if (info->board->chip_flag) + outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT | + MOXA_MUST_FCR_GDA_MODE_ENABLE, + info->ioaddr + UART_FCR); + else + outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT, + info->ioaddr + UART_FCR); + + /* read data port to reset things */ + (void) inb(info->ioaddr + UART_RX); + + if (info->tty) + set_bit(TTY_IO_ERROR, &info->tty->flags); + + info->flags &= ~ASYNC_INITIALIZED; + + if (info->board->chip_flag) + SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr); + + spin_unlock_irqrestore(&info->slock, flags); +} + +/* + * This routine is called whenever a serial port is opened. It + * enables interrupts for a serial port, linking in its async structure into + * the IRQ chain. It also performs the serial-specific + * initialization for the tty structure. + */ +static int mxser_open(struct tty_struct *tty, struct file *filp) +{ + struct mxser_port *info; + unsigned long flags; + int retval, line; + + line = tty->index; + if (line == MXSER_PORTS) + return 0; + if (line < 0 || line > MXSER_PORTS) + return -ENODEV; + info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD]; + if (!info->ioaddr) + return -ENODEV; + + tty->driver_data = info; + info->tty = tty; /* - status = mxser_get_msr(info->base, 0, info->port); - mxser_check_modem_status(info, status); - */ + * Start up serial port + */ + spin_lock_irqsave(&info->slock, flags); + info->count++; + spin_unlock_irqrestore(&info->slock, flags); + retval = mxser_startup(info); + if (retval) + return retval; + + retval = mxser_block_til_ready(tty, filp, info); + if (retval) + return retval; /* unmark here for very high baud rate (ex. 921600 bps) used */ tty->low_latency = 1; @@ -1010,11 +932,10 @@ static int mxser_open(struct tty_struct *tty, struct file *filp) */ static void mxser_close(struct tty_struct *tty, struct file *filp) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long timeout; unsigned long flags; - struct tty_ldisc *ld; if (tty->index == MXSER_PORTS) return; @@ -1041,7 +962,7 @@ static void mxser_close(struct tty_struct *tty, struct file *filp) } if (--info->count < 0) { printk(KERN_ERR "mxser_close: bad serial port count for " - "ttys%d: %d\n", info->port, info->count); + "ttys%d: %d\n", tty->index, info->count); info->count = 0; } if (info->count) { @@ -1070,20 +991,18 @@ static void mxser_close(struct tty_struct *tty, struct file *filp) * line status register. */ info->IER &= ~UART_IER_RLSI; - if (info->IsMoxaMustChipFlag) + if (info->board->chip_flag) info->IER &= ~MOXA_MUST_RECV_ISR; -/* by William - info->read_status_mask &= ~UART_LSR_DR; -*/ + if (info->flags & ASYNC_INITIALIZED) { - outb(info->IER, info->base + UART_IER); + outb(info->IER, info->ioaddr + UART_IER); /* * Before we drop DTR, make sure the UART transmitter * has completely drained; this is especially * important if there is a transmit FIFO! */ timeout = jiffies + HZ; - while (!(inb(info->base + UART_LSR) & UART_LSR_TEMT)) { + while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) { schedule_timeout_interruptible(5); if (time_after(jiffies, timeout)) break; @@ -1093,14 +1012,9 @@ static void mxser_close(struct tty_struct *tty, struct file *filp) if (tty->driver->flush_buffer) tty->driver->flush_buffer(tty); - - ld = tty_ldisc_ref(tty); - if (ld) { - if (ld->flush_buffer) - ld->flush_buffer(tty); - tty_ldisc_deref(ld); - } - + + tty_ldisc_flush(tty); + tty->closing = 0; info->event = 0; info->tty = NULL; @@ -1111,14 +1025,12 @@ static void mxser_close(struct tty_struct *tty, struct file *filp) } info->flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING); - wake_up_interruptible(&info->close_wait); - } static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count) { int c, total = 0; - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long flags; if (!info->xmit_buf) @@ -1142,13 +1054,15 @@ static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int cou total += c; } - if (info->xmit_cnt && !tty->stopped && !(info->IER & UART_IER_THRI)) { + if (info->xmit_cnt && !tty->stopped) { if (!tty->hw_stopped || (info->type == PORT_16550A) || - (info->IsMoxaMustChipFlag)) { + (info->board->chip_flag)) { spin_lock_irqsave(&info->slock, flags); + outb(info->IER & ~UART_IER_THRI, info->ioaddr + + UART_IER); info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); + outb(info->IER, info->ioaddr + UART_IER); spin_unlock_irqrestore(&info->slock, flags); } } @@ -1157,7 +1071,7 @@ static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int cou static void mxser_put_char(struct tty_struct *tty, unsigned char ch) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long flags; if (!info->xmit_buf) @@ -1171,13 +1085,14 @@ static void mxser_put_char(struct tty_struct *tty, unsigned char ch) info->xmit_head &= SERIAL_XMIT_SIZE - 1; info->xmit_cnt++; spin_unlock_irqrestore(&info->slock, flags); - if (!tty->stopped && !(info->IER & UART_IER_THRI)) { + if (!tty->stopped) { if (!tty->hw_stopped || (info->type == PORT_16550A) || - info->IsMoxaMustChipFlag) { + info->board->chip_flag) { spin_lock_irqsave(&info->slock, flags); + outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); + outb(info->IER, info->ioaddr + UART_IER); spin_unlock_irqrestore(&info->slock, flags); } } @@ -1186,7 +1101,7 @@ static void mxser_put_char(struct tty_struct *tty, unsigned char ch) static void mxser_flush_chars(struct tty_struct *tty) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long flags; if (info->xmit_cnt <= 0 || @@ -1194,21 +1109,22 @@ static void mxser_flush_chars(struct tty_struct *tty) !info->xmit_buf || (tty->hw_stopped && (info->type != PORT_16550A) && - (!info->IsMoxaMustChipFlag) + (!info->board->chip_flag) )) return; spin_lock_irqsave(&info->slock, flags); + outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); + outb(info->IER, info->ioaddr + UART_IER); spin_unlock_irqrestore(&info->slock, flags); } static int mxser_write_room(struct tty_struct *tty) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; int ret; ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; @@ -1219,13 +1135,13 @@ static int mxser_write_room(struct tty_struct *tty) static int mxser_chars_in_buffer(struct tty_struct *tty) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; return info->xmit_cnt; } static void mxser_flush_buffer(struct tty_struct *tty) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; char fcr; unsigned long flags; @@ -1233,361 +1149,415 @@ static void mxser_flush_buffer(struct tty_struct *tty) spin_lock_irqsave(&info->slock, flags); info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - /* below added by shinhay */ - fcr = inb(info->base + UART_FCR); + fcr = inb(info->ioaddr + UART_FCR); outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), - info->base + UART_FCR); - outb(fcr, info->base + UART_FCR); + info->ioaddr + UART_FCR); + outb(fcr, info->ioaddr + UART_FCR); spin_unlock_irqrestore(&info->slock, flags); - /* above added by shinhay */ tty_wakeup(tty); } -static int mxser_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg) +/* + * ------------------------------------------------------------ + * friends of mxser_ioctl() + * ------------------------------------------------------------ + */ +static int mxser_get_serial_info(struct mxser_port *info, + struct serial_struct __user *retinfo) +{ + struct serial_struct tmp = { + .type = info->type, + .line = info->tty->index, + .port = info->ioaddr, + .irq = info->board->irq, + .flags = info->flags, + .baud_base = info->baud_base, + .close_delay = info->close_delay, + .closing_wait = info->closing_wait, + .custom_divisor = info->custom_divisor, + .hub6 = 0 + }; + if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) + return -EFAULT; + return 0; +} + +static int mxser_set_serial_info(struct mxser_port *info, + struct serial_struct __user *new_info) { - struct mxser_struct *info = tty->driver_data; - int retval; - struct async_icount cprev, cnow; /* kernel counter temps */ - struct serial_icounter_struct __user *p_cuser; - unsigned long templ; - unsigned long flags; - void __user *argp = (void __user *)arg; + struct serial_struct new_serial; + unsigned long sl_flags; + unsigned int flags; + int retval = 0; - if (tty->index == MXSER_PORTS) - return mxser_ioctl_special(cmd, argp); + if (!new_info || !info->ioaddr) + return -EFAULT; + if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) + return -EFAULT; - /* following add by Victor Yu. 01-05-2004 */ - if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) { - int opmode, p; - static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f }; - int shiftbit; - unsigned char val, mask; + if ((new_serial.irq != info->board->irq) || + (new_serial.port != info->ioaddr) || + (new_serial.custom_divisor != info->custom_divisor) || + (new_serial.baud_base != info->baud_base)) + return -EPERM; - p = info->port % 4; - if (cmd == MOXA_SET_OP_MODE) { - if (get_user(opmode, (int __user *) argp)) - return -EFAULT; - if (opmode != RS232_MODE && - opmode != RS485_2WIRE_MODE && - opmode != RS422_MODE && - opmode != RS485_4WIRE_MODE) - return -EFAULT; - mask = ModeMask[p]; - shiftbit = p * 2; - val = inb(info->opmode_ioaddr); - val &= mask; - val |= (opmode << shiftbit); - outb(val, info->opmode_ioaddr); - } else { - shiftbit = p * 2; - opmode = inb(info->opmode_ioaddr) >> shiftbit; - opmode &= OP_MODE_MASK; - if (copy_to_user(argp, &opmode, sizeof(int))) - return -EFAULT; - } - return 0; - } - /* above add by Victor Yu. 01-05-2004 */ + flags = info->flags & ASYNC_SPD_MASK; - if ((cmd != TIOCGSERIAL) && (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) { - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - } - switch (cmd) { - case TCSBRK: /* SVID version: non-zero arg --> no break */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - if (!arg) - mxser_send_break(info, HZ / 4); /* 1/4 second */ - return 0; - case TCSBRKP: /* support for POSIX tcsendbreak() */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - mxser_send_break(info, arg ? arg * (HZ / 10) : HZ / 4); - return 0; - case TIOCGSOFTCAR: - return put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *)argp); - case TIOCSSOFTCAR: - if (get_user(templ, (unsigned long __user *) argp)) - return -EFAULT; - arg = templ; - tty->termios->c_cflag = ((tty->termios->c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0)); - return 0; - case TIOCGSERIAL: - return mxser_get_serial_info(info, argp); - case TIOCSSERIAL: - return mxser_set_serial_info(info, argp); - case TIOCSERGETLSR: /* Get line status register */ - return mxser_get_lsr_info(info, argp); + if (!capable(CAP_SYS_ADMIN)) { + if ((new_serial.baud_base != info->baud_base) || + (new_serial.close_delay != info->close_delay) || + ((new_serial.flags & ~ASYNC_USR_MASK) != (info->flags & ~ASYNC_USR_MASK))) + return -EPERM; + info->flags = ((info->flags & ~ASYNC_USR_MASK) | + (new_serial.flags & ASYNC_USR_MASK)); + } else { /* - * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change - * - mask passed in arg for lines of interest - * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) - * Caller should use TIOCGICOUNT to see which one it was + * OK, past this point, all the error checking has been done. + * At this point, we start making changes..... */ - case TIOCMIWAIT: - spin_lock_irqsave(&info->slock, flags); - cnow = info->icount; /* note the counters on entry */ - spin_unlock_irqrestore(&info->slock, flags); + info->flags = ((info->flags & ~ASYNC_FLAGS) | + (new_serial.flags & ASYNC_FLAGS)); + info->close_delay = new_serial.close_delay * HZ / 100; + info->closing_wait = new_serial.closing_wait * HZ / 100; + info->tty->low_latency = + (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; + info->tty->low_latency = 0; + } - wait_event_interruptible(info->delta_msr_wait, ({ - cprev = cnow; - spin_lock_irqsave(&info->slock, flags); - cnow = info->icount; /* atomic copy */ - spin_unlock_irqrestore(&info->slock, flags); + info->type = new_serial.type; - ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)); - })); - break; - /* - * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) - * Return: write counters to the user passed counter struct - * NB: both 1->0 and 0->1 transitions are counted except for - * RI where only 0->1 is counted. - */ - case TIOCGICOUNT: - spin_lock_irqsave(&info->slock, flags); - cnow = info->icount; - spin_unlock_irqrestore(&info->slock, flags); - p_cuser = argp; - /* modified by casper 1/11/2000 */ - if (put_user(cnow.frame, &p_cuser->frame)) - return -EFAULT; - if (put_user(cnow.brk, &p_cuser->brk)) - return -EFAULT; - if (put_user(cnow.overrun, &p_cuser->overrun)) - return -EFAULT; - if (put_user(cnow.buf_overrun, &p_cuser->buf_overrun)) - return -EFAULT; - if (put_user(cnow.parity, &p_cuser->parity)) - return -EFAULT; - if (put_user(cnow.rx, &p_cuser->rx)) - return -EFAULT; - if (put_user(cnow.tx, &p_cuser->tx)) - return -EFAULT; - put_user(cnow.cts, &p_cuser->cts); - put_user(cnow.dsr, &p_cuser->dsr); - put_user(cnow.rng, &p_cuser->rng); - put_user(cnow.dcd, &p_cuser->dcd); - return 0; - case MOXA_HighSpeedOn: - return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp); - case MOXA_SDS_RSTICOUNTER: { - info->mon_data.rxcnt = 0; - info->mon_data.txcnt = 0; - return 0; - } -/* (above) added by James. */ - case MOXA_ASPP_SETBAUD:{ - long baud; - if (get_user(baud, (long __user *)argp)) - return -EFAULT; - if (mxser_set_baud(info, baud) == -1) - return -1; - return 0; + process_txrx_fifo(info); + + if (info->flags & ASYNC_INITIALIZED) { + if (flags != (info->flags & ASYNC_SPD_MASK)) { + spin_lock_irqsave(&info->slock, sl_flags); + mxser_change_speed(info, NULL); + spin_unlock_irqrestore(&info->slock, sl_flags); } - case MOXA_ASPP_GETBAUD: - if (copy_to_user(argp, &info->realbaud, sizeof(long))) - return -EFAULT; + } else + retval = mxser_startup(info); - return 0; + return retval; +} - case MOXA_ASPP_OQUEUE:{ - int len, lsr; +/* + * mxser_get_lsr_info - get line status register info + * + * Purpose: Let user call ioctl() to get info when the UART physically + * is emptied. On bus types like RS485, the transmitter must + * release the bus after transmitting. This must be done when + * the transmit shift register is empty, not be done when the + * transmit holding register is empty. This functionality + * allows an RS485 driver to be written in user space. + */ +static int mxser_get_lsr_info(struct mxser_port *info, + unsigned int __user *value) +{ + unsigned char status; + unsigned int result; + unsigned long flags; - len = mxser_chars_in_buffer(tty); + spin_lock_irqsave(&info->slock, flags); + status = inb(info->ioaddr + UART_LSR); + spin_unlock_irqrestore(&info->slock, flags); + result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); + return put_user(result, value); +} - lsr = inb(info->base + UART_LSR) & UART_LSR_TEMT; +/* + * This routine sends a break character out the serial port. + */ +static void mxser_send_break(struct mxser_port *info, int duration) +{ + unsigned long flags; - len += (lsr ? 0 : 1); + if (!info->ioaddr) + return; + set_current_state(TASK_INTERRUPTIBLE); + spin_lock_irqsave(&info->slock, flags); + outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC, + info->ioaddr + UART_LCR); + spin_unlock_irqrestore(&info->slock, flags); + schedule_timeout(duration); + spin_lock_irqsave(&info->slock, flags); + outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC, + info->ioaddr + UART_LCR); + spin_unlock_irqrestore(&info->slock, flags); +} - if (copy_to_user(argp, &len, sizeof(int))) - return -EFAULT; +static int mxser_tiocmget(struct tty_struct *tty, struct file *file) +{ + struct mxser_port *info = tty->driver_data; + unsigned char control, status; + unsigned long flags; - return 0; - } - case MOXA_ASPP_MON: { - int mcr, status; - /* info->mon_data.ser_param = tty->termios->c_cflag; */ + if (tty->index == MXSER_PORTS) + return -ENOIOCTLCMD; + if (test_bit(TTY_IO_ERROR, &tty->flags)) + return -EIO; - status = mxser_get_msr(info->base, 1, info->port, info); - mxser_check_modem_status(info, status); + control = info->MCR; - mcr = inb(info->base + UART_MCR); - if (mcr & MOXA_MUST_MCR_XON_FLAG) - info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD; - else - info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD; + spin_lock_irqsave(&info->slock, flags); + status = inb(info->ioaddr + UART_MSR); + if (status & UART_MSR_ANY_DELTA) + mxser_check_modem_status(info, status); + spin_unlock_irqrestore(&info->slock, flags); + return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) | + ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) | + ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) | + ((status & UART_MSR_RI) ? TIOCM_RNG : 0) | + ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) | + ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); +} - if (mcr & MOXA_MUST_MCR_TX_XON) - info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT; - else - info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT; +static int mxser_tiocmset(struct tty_struct *tty, struct file *file, + unsigned int set, unsigned int clear) +{ + struct mxser_port *info = tty->driver_data; + unsigned long flags; - if (info->tty->hw_stopped) - info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD; - else - info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD; - if (copy_to_user(argp, &info->mon_data, - sizeof(struct mxser_mon))) - return -EFAULT; + if (tty->index == MXSER_PORTS) + return -ENOIOCTLCMD; + if (test_bit(TTY_IO_ERROR, &tty->flags)) + return -EIO; - return 0; - } + spin_lock_irqsave(&info->slock, flags); - case MOXA_ASPP_LSTATUS: { - if (copy_to_user(argp, &info->err_shadow, - sizeof(unsigned char))) - return -EFAULT; + if (set & TIOCM_RTS) + info->MCR |= UART_MCR_RTS; + if (set & TIOCM_DTR) + info->MCR |= UART_MCR_DTR; - info->err_shadow = 0; - return 0; - } - case MOXA_SET_BAUD_METHOD: { - int method; + if (clear & TIOCM_RTS) + info->MCR &= ~UART_MCR_RTS; + if (clear & TIOCM_DTR) + info->MCR &= ~UART_MCR_DTR; - if (get_user(method, (int __user *)argp)) - return -EFAULT; - mxser_set_baud_method[info->port] = method; - if (copy_to_user(argp, &method, sizeof(int))) - return -EFAULT; + outb(info->MCR, info->ioaddr + UART_MCR); + spin_unlock_irqrestore(&info->slock, flags); + return 0; +} - return 0; - } - default: - return -ENOIOCTLCMD; +static int __init mxser_program_mode(int port) +{ + int id, i, j, n; + + outb(0, port); + outb(0, port); + outb(0, port); + (void)inb(port); + (void)inb(port); + outb(0, port); + (void)inb(port); + + id = inb(port + 1) & 0x1F; + if ((id != C168_ASIC_ID) && + (id != C104_ASIC_ID) && + (id != C102_ASIC_ID) && + (id != CI132_ASIC_ID) && + (id != CI134_ASIC_ID) && + (id != CI104J_ASIC_ID)) + return -1; + for (i = 0, j = 0; i < 4; i++) { + n = inb(port + 2); + if (n == 'M') { + j = 1; + } else if ((j == 1) && (n == 1)) { + j = 2; + break; + } else + j = 0; } - return 0; + if (j != 2) + id = -2; + return id; } -#ifndef CMSPAR -#define CMSPAR 010000000000 -#endif +static void __init mxser_normal_mode(int port) +{ + int i, n; + + outb(0xA5, port + 1); + outb(0x80, port + 3); + outb(12, port + 0); /* 9600 bps */ + outb(0, port + 1); + outb(0x03, port + 3); /* 8 data bits */ + outb(0x13, port + 4); /* loop back mode */ + for (i = 0; i < 16; i++) { + n = inb(port + 5); + if ((n & 0x61) == 0x60) + break; + if ((n & 1) == 1) + (void)inb(port); + } + outb(0x00, port + 4); +} + +#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */ +#define CHIP_DO 0x02 /* Serial Data Output in Eprom */ +#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */ +#define CHIP_DI 0x08 /* Serial Data Input in Eprom */ +#define EN_CCMD 0x000 /* Chip's command register */ +#define EN0_RSARLO 0x008 /* Remote start address reg 0 */ +#define EN0_RSARHI 0x009 /* Remote start address reg 1 */ +#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */ +#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */ +#define EN0_DCFG 0x00E /* Data configuration reg WR */ +#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */ +#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */ +#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */ +static int __init mxser_read_register(int port, unsigned short *regs) +{ + int i, k, value, id; + unsigned int j; + + id = mxser_program_mode(port); + if (id < 0) + return id; + for (i = 0; i < 14; i++) { + k = (i & 0x3F) | 0x180; + for (j = 0x100; j > 0; j >>= 1) { + outb(CHIP_CS, port); + if (k & j) { + outb(CHIP_CS | CHIP_DO, port); + outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */ + } else { + outb(CHIP_CS, port); + outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */ + } + } + (void)inb(port); + value = 0; + for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) { + outb(CHIP_CS, port); + outb(CHIP_CS | CHIP_SK, port); + if (inb(port) & CHIP_DI) + value |= j; + } + regs[i] = value; + outb(0, port); + } + mxser_normal_mode(port); + return id; +} static int mxser_ioctl_special(unsigned int cmd, void __user *argp) { - int i, result, status; + struct mxser_port *port; + int result, status; + unsigned int i, j; switch (cmd) { - case MOXA_GET_CONF: - if (copy_to_user(argp, mxsercfg, - sizeof(struct mxser_hwconf) * 4)) - return -EFAULT; - return 0; case MOXA_GET_MAJOR: - if (copy_to_user(argp, &ttymajor, sizeof(int))) - return -EFAULT; - return 0; - - case MOXA_GET_CUMAJOR: - if (copy_to_user(argp, &calloutmajor, sizeof(int))) - return -EFAULT; - return 0; + return put_user(ttymajor, (int __user *)argp); case MOXA_CHKPORTENABLE: result = 0; - for (i = 0; i < MXSER_PORTS; i++) { - if (mxvar_table[i].base) - result |= (1 << i); - } + + for (i = 0; i < MXSER_BOARDS; i++) + for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) + if (mxser_boards[i].ports[j].ioaddr) + result |= (1 << i); + return put_user(result, (unsigned long __user *)argp); case MOXA_GETDATACOUNT: if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log))) return -EFAULT; return 0; case MOXA_GETMSTATUS: - for (i = 0; i < MXSER_PORTS; i++) { - GMStatus[i].ri = 0; - if (!mxvar_table[i].base) { - GMStatus[i].dcd = 0; - GMStatus[i].dsr = 0; - GMStatus[i].cts = 0; - continue; - } + for (i = 0; i < MXSER_BOARDS; i++) + for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) { + port = &mxser_boards[i].ports[j]; + + GMStatus[i].ri = 0; + if (!port->ioaddr) { + GMStatus[i].dcd = 0; + GMStatus[i].dsr = 0; + GMStatus[i].cts = 0; + continue; + } - if (!mxvar_table[i].tty || !mxvar_table[i].tty->termios) - GMStatus[i].cflag = mxvar_table[i].normal_termios.c_cflag; - else - GMStatus[i].cflag = mxvar_table[i].tty->termios->c_cflag; + if (!port->tty || !port->tty->termios) + GMStatus[i].cflag = + port->normal_termios.c_cflag; + else + GMStatus[i].cflag = + port->tty->termios->c_cflag; - status = inb(mxvar_table[i].base + UART_MSR); - if (status & 0x80 /*UART_MSR_DCD */ ) - GMStatus[i].dcd = 1; - else - GMStatus[i].dcd = 0; + status = inb(port->ioaddr + UART_MSR); + if (status & 0x80 /*UART_MSR_DCD */ ) + GMStatus[i].dcd = 1; + else + GMStatus[i].dcd = 0; - if (status & 0x20 /*UART_MSR_DSR */ ) - GMStatus[i].dsr = 1; - else - GMStatus[i].dsr = 0; + if (status & 0x20 /*UART_MSR_DSR */ ) + GMStatus[i].dsr = 1; + else + GMStatus[i].dsr = 0; - if (status & 0x10 /*UART_MSR_CTS */ ) - GMStatus[i].cts = 1; - else - GMStatus[i].cts = 0; - } + if (status & 0x10 /*UART_MSR_CTS */ ) + GMStatus[i].cts = 1; + else + GMStatus[i].cts = 0; + } if (copy_to_user(argp, GMStatus, sizeof(struct mxser_mstatus) * MXSER_PORTS)) return -EFAULT; return 0; case MOXA_ASPP_MON_EXT: { - int status; - int opmode, p; - int shiftbit; - unsigned cflag, iflag; - - for (i = 0; i < MXSER_PORTS; i++) { - if (!mxvar_table[i].base) + int p, shiftbit; + unsigned long opmode; + unsigned cflag, iflag; + + for (i = 0; i < MXSER_BOARDS; i++) + for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) { + port = &mxser_boards[i].ports[j]; + if (!port->ioaddr) continue; - status = mxser_get_msr(mxvar_table[i].base, 0, - i, &(mxvar_table[i])); - /* - mxser_check_modem_status(&mxvar_table[i], - status); - */ + status = mxser_get_msr(port->ioaddr, 0, i); + if (status & UART_MSR_TERI) - mxvar_table[i].icount.rng++; + port->icount.rng++; if (status & UART_MSR_DDSR) - mxvar_table[i].icount.dsr++; + port->icount.dsr++; if (status & UART_MSR_DDCD) - mxvar_table[i].icount.dcd++; + port->icount.dcd++; if (status & UART_MSR_DCTS) - mxvar_table[i].icount.cts++; - - mxvar_table[i].mon_data.modem_status = status; - mon_data_ext.rx_cnt[i] = mxvar_table[i].mon_data.rxcnt; - mon_data_ext.tx_cnt[i] = mxvar_table[i].mon_data.txcnt; - mon_data_ext.up_rxcnt[i] = mxvar_table[i].mon_data.up_rxcnt; - mon_data_ext.up_txcnt[i] = mxvar_table[i].mon_data.up_txcnt; - mon_data_ext.modem_status[i] = mxvar_table[i].mon_data.modem_status; - mon_data_ext.baudrate[i] = mxvar_table[i].realbaud; - - if (!mxvar_table[i].tty || !mxvar_table[i].tty->termios) { - cflag = mxvar_table[i].normal_termios.c_cflag; - iflag = mxvar_table[i].normal_termios.c_iflag; + port->icount.cts++; + + port->mon_data.modem_status = status; + mon_data_ext.rx_cnt[i] = port->mon_data.rxcnt; + mon_data_ext.tx_cnt[i] = port->mon_data.txcnt; + mon_data_ext.up_rxcnt[i] = + port->mon_data.up_rxcnt; + mon_data_ext.up_txcnt[i] = + port->mon_data.up_txcnt; + mon_data_ext.modem_status[i] = + port->mon_data.modem_status; + mon_data_ext.baudrate[i] = + tty_get_baud_rate(port->tty); + + if (!port->tty || !port->tty->termios) { + cflag = port->normal_termios.c_cflag; + iflag = port->normal_termios.c_iflag; } else { - cflag = mxvar_table[i].tty->termios->c_cflag; - iflag = mxvar_table[i].tty->termios->c_iflag; + cflag = port->tty->termios->c_cflag; + iflag = port->tty->termios->c_iflag; } mon_data_ext.databits[i] = cflag & CSIZE; mon_data_ext.stopbits[i] = cflag & CSTOPB; - mon_data_ext.parity[i] = cflag & (PARENB | PARODD | CMSPAR); + mon_data_ext.parity[i] = + cflag & (PARENB | PARODD | CMSPAR); mon_data_ext.flowctrl[i] = 0x00; @@ -1597,101 +1567,260 @@ static int mxser_ioctl_special(unsigned int cmd, void __user *argp) if (iflag & (IXON | IXOFF)) mon_data_ext.flowctrl[i] |= 0x0C; - if (mxvar_table[i].type == PORT_16550A) + if (port->type == PORT_16550A) mon_data_ext.fifo[i] = 1; else mon_data_ext.fifo[i] = 0; p = i % 4; shiftbit = p * 2; - opmode = inb(mxvar_table[i].opmode_ioaddr) >> shiftbit; + opmode = inb(port->opmode_ioaddr) >> shiftbit; opmode &= OP_MODE_MASK; mon_data_ext.iftype[i] = opmode; } - if (copy_to_user(argp, &mon_data_ext, sizeof(struct mxser_mon_ext))) + if (copy_to_user(argp, &mon_data_ext, + sizeof(mon_data_ext))) return -EFAULT; return 0; - } - default: + } default: return -ENOIOCTLCMD; } return 0; } -static void mxser_stoprx(struct tty_struct *tty) +static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg, + struct async_icount *cprev) { - struct mxser_struct *info = tty->driver_data; - /* unsigned long flags; */ + struct async_icount cnow; + unsigned long flags; + int ret; - info->ldisc_stop_rx = 1; - if (I_IXOFF(tty)) { - /* MX_LOCK(&info->slock); */ - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag) { - info->IER &= ~MOXA_MUST_RECV_ISR; - outb(info->IER, info->base + UART_IER); - } else { - /* above add by Victor Yu. 09-02-2002 */ - info->x_char = STOP_CHAR(tty); - /* mask by Victor Yu. 09-02-2002 */ - /* outb(info->IER, 0); */ - outb(0, info->base + UART_IER); - info->IER |= UART_IER_THRI; - /* force Tx interrupt */ - outb(info->IER, info->base + UART_IER); - } /* add by Victor Yu. 09-02-2002 */ - /* MX_UNLOCK(&info->slock); */ - } + spin_lock_irqsave(&info->slock, flags); + cnow = info->icount; /* atomic copy */ + spin_unlock_irqrestore(&info->slock, flags); - if (info->tty->termios->c_cflag & CRTSCTS) { - /* MX_LOCK(&info->slock); */ - info->MCR &= ~UART_MCR_RTS; - outb(info->MCR, info->base + UART_MCR); - /* MX_UNLOCK(&info->slock); */ - } -} + ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) || + ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) || + ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) || + ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts)); -static void mxser_startrx(struct tty_struct *tty) + *cprev = cnow; + + return ret; +} + +static int mxser_ioctl(struct tty_struct *tty, struct file *file, + unsigned int cmd, unsigned long arg) { - struct mxser_struct *info = tty->driver_data; - /* unsigned long flags; */ + struct mxser_port *info = tty->driver_data; + struct async_icount cnow; + struct serial_icounter_struct __user *p_cuser; + unsigned long flags; + void __user *argp = (void __user *)arg; + int retval; - info->ldisc_stop_rx = 0; - if (I_IXOFF(tty)) { - if (info->x_char) - info->x_char = 0; - else { - /* MX_LOCK(&info->slock); */ + if (tty->index == MXSER_PORTS) + return mxser_ioctl_special(cmd, argp); - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag) { - info->IER |= MOXA_MUST_RECV_ISR; - outb(info->IER, info->base + UART_IER); - } else { - /* above add by Victor Yu. 09-02-2002 */ + if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) { + int p; + unsigned long opmode; + static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f }; + int shiftbit; + unsigned char val, mask; - info->x_char = START_CHAR(tty); - /* mask by Victor Yu. 09-02-2002 */ - /* outb(info->IER, 0); */ - /* add by Victor Yu. 09-02-2002 */ - outb(0, info->base + UART_IER); - /* force Tx interrupt */ - info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - } /* add by Victor Yu. 09-02-2002 */ - /* MX_UNLOCK(&info->slock); */ + p = tty->index % 4; + if (cmd == MOXA_SET_OP_MODE) { + if (get_user(opmode, (int __user *) argp)) + return -EFAULT; + if (opmode != RS232_MODE && + opmode != RS485_2WIRE_MODE && + opmode != RS422_MODE && + opmode != RS485_4WIRE_MODE) + return -EFAULT; + mask = ModeMask[p]; + shiftbit = p * 2; + val = inb(info->opmode_ioaddr); + val &= mask; + val |= (opmode << shiftbit); + outb(val, info->opmode_ioaddr); + } else { + shiftbit = p * 2; + opmode = inb(info->opmode_ioaddr) >> shiftbit; + opmode &= OP_MODE_MASK; + if (put_user(opmode, (int __user *)argp)) + return -EFAULT; + } + return 0; + } + + if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && cmd != TIOCGICOUNT && + test_bit(TTY_IO_ERROR, &tty->flags)) + return -EIO; + + switch (cmd) { + case TCSBRK: /* SVID version: non-zero arg --> no break */ + retval = tty_check_change(tty); + if (retval) + return retval; + tty_wait_until_sent(tty, 0); + if (!arg) + mxser_send_break(info, HZ / 4); /* 1/4 second */ + return 0; + case TCSBRKP: /* support for POSIX tcsendbreak() */ + retval = tty_check_change(tty); + if (retval) + return retval; + tty_wait_until_sent(tty, 0); + mxser_send_break(info, arg ? arg * (HZ / 10) : HZ / 4); + return 0; + case TIOCGSOFTCAR: + return put_user(!!C_CLOCAL(tty), (unsigned long __user *)argp); + case TIOCSSOFTCAR: + if (get_user(arg, (unsigned long __user *)argp)) + return -EFAULT; + tty->termios->c_cflag = ((tty->termios->c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0)); + return 0; + case TIOCGSERIAL: + return mxser_get_serial_info(info, argp); + case TIOCSSERIAL: + return mxser_set_serial_info(info, argp); + case TIOCSERGETLSR: /* Get line status register */ + return mxser_get_lsr_info(info, argp); + /* + * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change + * - mask passed in arg for lines of interest + * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) + * Caller should use TIOCGICOUNT to see which one it was + */ + case TIOCMIWAIT: + spin_lock_irqsave(&info->slock, flags); + cnow = info->icount; /* note the counters on entry */ + spin_unlock_irqrestore(&info->slock, flags); + + return wait_event_interruptible(info->delta_msr_wait, + mxser_cflags_changed(info, arg, &cnow)); + /* + * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) + * Return: write counters to the user passed counter struct + * NB: both 1->0 and 0->1 transitions are counted except for + * RI where only 0->1 is counted. + */ + case TIOCGICOUNT: + spin_lock_irqsave(&info->slock, flags); + cnow = info->icount; + spin_unlock_irqrestore(&info->slock, flags); + p_cuser = argp; + if (put_user(cnow.frame, &p_cuser->frame)) + return -EFAULT; + if (put_user(cnow.brk, &p_cuser->brk)) + return -EFAULT; + if (put_user(cnow.overrun, &p_cuser->overrun)) + return -EFAULT; + if (put_user(cnow.buf_overrun, &p_cuser->buf_overrun)) + return -EFAULT; + if (put_user(cnow.parity, &p_cuser->parity)) + return -EFAULT; + if (put_user(cnow.rx, &p_cuser->rx)) + return -EFAULT; + if (put_user(cnow.tx, &p_cuser->tx)) + return -EFAULT; + put_user(cnow.cts, &p_cuser->cts); + put_user(cnow.dsr, &p_cuser->dsr); + put_user(cnow.rng, &p_cuser->rng); + put_user(cnow.dcd, &p_cuser->dcd); + return 0; + case MOXA_HighSpeedOn: + return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp); + case MOXA_SDS_RSTICOUNTER: + info->mon_data.rxcnt = 0; + info->mon_data.txcnt = 0; + return 0; + + case MOXA_ASPP_OQUEUE:{ + int len, lsr; + + len = mxser_chars_in_buffer(tty); + + lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT; + + len += (lsr ? 0 : 1); + + return put_user(len, (int __user *)argp); + } + case MOXA_ASPP_MON: { + int mcr, status; + + status = mxser_get_msr(info->ioaddr, 1, tty->index); + mxser_check_modem_status(info, status); + + mcr = inb(info->ioaddr + UART_MCR); + if (mcr & MOXA_MUST_MCR_XON_FLAG) + info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD; + else + info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD; + + if (mcr & MOXA_MUST_MCR_TX_XON) + info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT; + else + info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT; + + if (info->tty->hw_stopped) + info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD; + else + info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD; + + if (copy_to_user(argp, &info->mon_data, + sizeof(struct mxser_mon))) + return -EFAULT; + + return 0; + } + case MOXA_ASPP_LSTATUS: { + if (put_user(info->err_shadow, (unsigned char __user *)argp)) + return -EFAULT; + + info->err_shadow = 0; + return 0; + } + case MOXA_SET_BAUD_METHOD: { + int method; + + if (get_user(method, (int __user *)argp)) + return -EFAULT; + mxser_set_baud_method[tty->index] = method; + return put_user(method, (int __user *)argp); + } + default: + return -ENOIOCTLCMD; + } + return 0; +} + +static void mxser_stoprx(struct tty_struct *tty) +{ + struct mxser_port *info = tty->driver_data; + + info->ldisc_stop_rx = 1; + if (I_IXOFF(tty)) { + if (info->board->chip_flag) { + info->IER &= ~MOXA_MUST_RECV_ISR; + outb(info->IER, info->ioaddr + UART_IER); + } else { + info->x_char = STOP_CHAR(tty); + outb(0, info->ioaddr + UART_IER); + info->IER |= UART_IER_THRI; + outb(info->IER, info->ioaddr + UART_IER); } } if (info->tty->termios->c_cflag & CRTSCTS) { - /* MX_LOCK(&info->slock); */ - info->MCR |= UART_MCR_RTS; - outb(info->MCR, info->base + UART_MCR); - /* MX_UNLOCK(&info->slock); */ + info->MCR &= ~UART_MCR_RTS; + outb(info->MCR, info->ioaddr + UART_MCR); } } @@ -1701,51 +1830,34 @@ static void mxser_startrx(struct tty_struct *tty) */ static void mxser_throttle(struct tty_struct *tty) { - /* struct mxser_struct *info = tty->driver_data; */ - /* unsigned long flags; */ - - /* MX_LOCK(&info->slock); */ mxser_stoprx(tty); - /* MX_UNLOCK(&info->slock); */ } static void mxser_unthrottle(struct tty_struct *tty) { - /* struct mxser_struct *info = tty->driver_data; */ - /* unsigned long flags; */ - - /* MX_LOCK(&info->slock); */ - mxser_startrx(tty); - /* MX_UNLOCK(&info->slock); */ -} - -static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios) -{ - struct mxser_struct *info = tty->driver_data; - unsigned long flags; - - mxser_change_speed(info, old_termios); - - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { - tty->hw_stopped = 0; - mxser_start(tty); - } - -/* Handle sw stopped */ - if ((old_termios->c_iflag & IXON) && - !(tty->termios->c_iflag & IXON)) { - tty->stopped = 0; + struct mxser_port *info = tty->driver_data; - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag) { - spin_lock_irqsave(&info->slock, flags); - DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->base); - spin_unlock_irqrestore(&info->slock, flags); + /* startrx */ + info->ldisc_stop_rx = 0; + if (I_IXOFF(tty)) { + if (info->x_char) + info->x_char = 0; + else { + if (info->board->chip_flag) { + info->IER |= MOXA_MUST_RECV_ISR; + outb(info->IER, info->ioaddr + UART_IER); + } else { + info->x_char = START_CHAR(tty); + outb(0, info->ioaddr + UART_IER); + info->IER |= UART_IER_THRI; + outb(info->IER, info->ioaddr + UART_IER); + } } - /* above add by Victor Yu. 09-02-2002 */ + } - mxser_start(tty); + if (info->tty->termios->c_cflag & CRTSCTS) { + info->MCR |= UART_MCR_RTS; + outb(info->MCR, info->ioaddr + UART_MCR); } } @@ -1757,36 +1869,67 @@ static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termi */ static void mxser_stop(struct tty_struct *tty) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long flags; spin_lock_irqsave(&info->slock, flags); if (info->IER & UART_IER_THRI) { info->IER &= ~UART_IER_THRI; - outb(info->IER, info->base + UART_IER); + outb(info->IER, info->ioaddr + UART_IER); } spin_unlock_irqrestore(&info->slock, flags); } static void mxser_start(struct tty_struct *tty) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long flags; spin_lock_irqsave(&info->slock, flags); - if (info->xmit_cnt && info->xmit_buf && !(info->IER & UART_IER_THRI)) { + if (info->xmit_cnt && info->xmit_buf) { + outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); + outb(info->IER, info->ioaddr + UART_IER); } spin_unlock_irqrestore(&info->slock, flags); } +static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios) +{ + struct mxser_port *info = tty->driver_data; + unsigned long flags; + + spin_lock_irqsave(&info->slock, flags); + mxser_change_speed(info, old_termios); + spin_unlock_irqrestore(&info->slock, flags); + + if ((old_termios->c_cflag & CRTSCTS) && + !(tty->termios->c_cflag & CRTSCTS)) { + tty->hw_stopped = 0; + mxser_start(tty); + } + + /* Handle sw stopped */ + if ((old_termios->c_iflag & IXON) && + !(tty->termios->c_iflag & IXON)) { + tty->stopped = 0; + + if (info->board->chip_flag) { + spin_lock_irqsave(&info->slock, flags); + DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr); + spin_unlock_irqrestore(&info->slock, flags); + } + + mxser_start(tty); + } +} + /* * mxser_wait_until_sent() --- wait until the transmitter is empty */ static void mxser_wait_until_sent(struct tty_struct *tty, int timeout) { - struct mxser_struct *info = tty->driver_data; + struct mxser_port *info = tty->driver_data; unsigned long orig_jiffies, char_time; int lsr; @@ -1827,1161 +1970,450 @@ static void mxser_wait_until_sent(struct tty_struct *tty, int timeout) timeout, char_time); printk("jiff=%lu...", jiffies); #endif - while (!((lsr = inb(info->base + UART_LSR)) & UART_LSR_TEMT)) { + while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) { #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT printk("lsr = %d (jiff=%lu)...", lsr, jiffies); #endif schedule_timeout_interruptible(char_time); if (signal_pending(current)) - break; - if (timeout && time_after(jiffies, orig_jiffies + timeout)) - break; - } - set_current_state(TASK_RUNNING); - -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); -#endif -} - - -/* - * This routine is called by tty_hangup() when a hangup is signaled. - */ -void mxser_hangup(struct tty_struct *tty) -{ - struct mxser_struct *info = tty->driver_data; - - mxser_flush_buffer(tty); - mxser_shutdown(info); - info->event = 0; - info->count = 0; - info->flags &= ~ASYNC_NORMAL_ACTIVE; - info->tty = NULL; - wake_up_interruptible(&info->open_wait); -} - - -/* added by James 03-12-2004. */ -/* - * mxser_rs_break() --- routine which turns the break handling on or off - */ -static void mxser_rs_break(struct tty_struct *tty, int break_state) -{ - struct mxser_struct *info = tty->driver_data; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - if (break_state == -1) - outb(inb(info->base + UART_LCR) | UART_LCR_SBC, - info->base + UART_LCR); - else - outb(inb(info->base + UART_LCR) & ~UART_LCR_SBC, - info->base + UART_LCR); - spin_unlock_irqrestore(&info->slock, flags); -} - -/* (above) added by James. */ - - -/* - * This is the serial driver's generic interrupt routine - */ -static irqreturn_t mxser_interrupt(int irq, void *dev_id) -{ - int status, iir, i; - struct mxser_struct *info; - struct mxser_struct *port; - int max, irqbits, bits, msr; - int pass_counter = 0; - int handled = IRQ_NONE; - - port = NULL; - /* spin_lock(&gm_lock); */ - - for (i = 0; i < MXSER_BOARDS; i++) { - if (dev_id == &(mxvar_table[i * MXSER_PORTS_PER_BOARD])) { - port = dev_id; - break; - } - } - - if (i == MXSER_BOARDS) - goto irq_stop; - if (port == 0) - goto irq_stop; - max = mxser_numports[mxsercfg[i].board_type - 1]; - while (1) { - irqbits = inb(port->vector) & port->vectormask; - if (irqbits == port->vectormask) - break; - - handled = IRQ_HANDLED; - for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) { - if (irqbits == port->vectormask) - break; - if (bits & irqbits) - continue; - info = port + i; - - /* following add by Victor Yu. 09-13-2002 */ - iir = inb(info->base + UART_IIR); - if (iir & UART_IIR_NO_INT) - continue; - iir &= MOXA_MUST_IIR_MASK; - if (!info->tty) { - status = inb(info->base + UART_LSR); - outb(0x27, info->base + UART_FCR); - inb(info->base + UART_MSR); - continue; - } - - /* mask by Victor Yu. 09-13-2002 - if ( !info->tty || - (inb(info->base + UART_IIR) & UART_IIR_NO_INT) ) - continue; - */ - /* mask by Victor Yu. 09-02-2002 - status = inb(info->base + UART_LSR) & info->read_status_mask; - */ - - /* following add by Victor Yu. 09-02-2002 */ - status = inb(info->base + UART_LSR); - - if (status & UART_LSR_PE) - info->err_shadow |= NPPI_NOTIFY_PARITY; - if (status & UART_LSR_FE) - info->err_shadow |= NPPI_NOTIFY_FRAMING; - if (status & UART_LSR_OE) - info->err_shadow |= NPPI_NOTIFY_HW_OVERRUN; - if (status & UART_LSR_BI) - info->err_shadow |= NPPI_NOTIFY_BREAK; - - if (info->IsMoxaMustChipFlag) { - /* - if ( (status & 0x02) && !(status & 0x01) ) { - outb(info->base+UART_FCR, 0x23); - continue; - } - */ - if (iir == MOXA_MUST_IIR_GDA || - iir == MOXA_MUST_IIR_RDA || - iir == MOXA_MUST_IIR_RTO || - iir == MOXA_MUST_IIR_LSR) - mxser_receive_chars(info, &status); - - } else { - /* above add by Victor Yu. 09-02-2002 */ - - status &= info->read_status_mask; - if (status & UART_LSR_DR) - mxser_receive_chars(info, &status); - } - msr = inb(info->base + UART_MSR); - if (msr & UART_MSR_ANY_DELTA) { - mxser_check_modem_status(info, msr); - } - /* following add by Victor Yu. 09-13-2002 */ - if (info->IsMoxaMustChipFlag) { - if ((iir == 0x02) && (status & UART_LSR_THRE)) { - mxser_transmit_chars(info); - } - } else { - /* above add by Victor Yu. 09-13-2002 */ - - if (status & UART_LSR_THRE) { -/* 8-2-99 by William - if ( info->x_char || (info->xmit_cnt > 0) ) -*/ - mxser_transmit_chars(info); - } - } - } - if (pass_counter++ > MXSER_ISR_PASS_LIMIT) { - break; /* Prevent infinite loops */ - } - } - - irq_stop: - /* spin_unlock(&gm_lock); */ - return handled; -} - -static void mxser_receive_chars(struct mxser_struct *info, int *status) -{ - struct tty_struct *tty = info->tty; - unsigned char ch, gdl; - int ignored = 0; - int cnt = 0; - int recv_room; - int max = 256; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - - recv_room = tty->receive_room; - if ((recv_room == 0) && (!info->ldisc_stop_rx)) { - /* mxser_throttle(tty); */ - mxser_stoprx(tty); - /* return; */ - } - - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag != MOXA_OTHER_UART) { - - if (*status & UART_LSR_SPECIAL) { - goto intr_old; - } - /* following add by Victor Yu. 02-11-2004 */ - if (info->IsMoxaMustChipFlag == MOXA_MUST_MU860_HWID && - (*status & MOXA_MUST_LSR_RERR)) - goto intr_old; - /* above add by Victor Yu. 02-14-2004 */ - if (*status & MOXA_MUST_LSR_RERR) - goto intr_old; - - gdl = inb(info->base + MOXA_MUST_GDL_REGISTER); - - /* add by Victor Yu. 02-11-2004 */ - if (info->IsMoxaMustChipFlag == MOXA_MUST_MU150_HWID) - gdl &= MOXA_MUST_GDL_MASK; - if (gdl >= recv_room) { - if (!info->ldisc_stop_rx) { - /* mxser_throttle(tty); */ - mxser_stoprx(tty); - } - /* return; */ - } - while (gdl--) { - ch = inb(info->base + UART_RX); - tty_insert_flip_char(tty, ch, 0); - cnt++; - /* - if ((cnt >= HI_WATER) && (info->stop_rx == 0)) { - mxser_stoprx(tty); - info->stop_rx = 1; - break; - } */ - } - goto end_intr; - } - intr_old: - /* above add by Victor Yu. 09-02-2002 */ - - do { - if (max-- < 0) - break; - /* - if ((cnt >= HI_WATER) && (info->stop_rx == 0)) { - mxser_stoprx(tty); - info->stop_rx=1; - break; - } - */ - - ch = inb(info->base + UART_RX); - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag && (*status & UART_LSR_OE) /*&& !(*status&UART_LSR_DR) */ ) - outb(0x23, info->base + UART_FCR); - *status &= info->read_status_mask; - /* above add by Victor Yu. 09-02-2002 */ - if (*status & info->ignore_status_mask) { - if (++ignored > 100) - break; - } else { - char flag = 0; - if (*status & UART_LSR_SPECIAL) { - if (*status & UART_LSR_BI) { - flag = TTY_BREAK; -/* added by casper 1/11/2000 */ - info->icount.brk++; -/* */ - if (info->flags & ASYNC_SAK) - do_SAK(tty); - } else if (*status & UART_LSR_PE) { - flag = TTY_PARITY; -/* added by casper 1/11/2000 */ - info->icount.parity++; -/* */ - } else if (*status & UART_LSR_FE) { - flag = TTY_FRAME; -/* added by casper 1/11/2000 */ - info->icount.frame++; -/* */ - } else if (*status & UART_LSR_OE) { - flag = TTY_OVERRUN; -/* added by casper 1/11/2000 */ - info->icount.overrun++; -/* */ - } - } - tty_insert_flip_char(tty, ch, flag); - cnt++; - if (cnt >= recv_room) { - if (!info->ldisc_stop_rx) { - /* mxser_throttle(tty); */ - mxser_stoprx(tty); - } - break; - } - - } - - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag) - break; - /* above add by Victor Yu. 09-02-2002 */ - - /* mask by Victor Yu. 09-02-2002 - *status = inb(info->base + UART_LSR) & info->read_status_mask; - */ - /* following add by Victor Yu. 09-02-2002 */ - *status = inb(info->base + UART_LSR); - /* above add by Victor Yu. 09-02-2002 */ - } while (*status & UART_LSR_DR); - -end_intr: /* add by Victor Yu. 09-02-2002 */ - mxvar_log.rxcnt[info->port] += cnt; - info->mon_data.rxcnt += cnt; - info->mon_data.up_rxcnt += cnt; - spin_unlock_irqrestore(&info->slock, flags); - - tty_flip_buffer_push(tty); -} - -static void mxser_transmit_chars(struct mxser_struct *info) -{ - int count, cnt; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - - if (info->x_char) { - outb(info->x_char, info->base + UART_TX); - info->x_char = 0; - mxvar_log.txcnt[info->port]++; - info->mon_data.txcnt++; - info->mon_data.up_txcnt++; - -/* added by casper 1/11/2000 */ - info->icount.tx++; -/* */ - spin_unlock_irqrestore(&info->slock, flags); - return; - } - - if (info->xmit_buf == 0) { - spin_unlock_irqrestore(&info->slock, flags); - return; - } - - if ((info->xmit_cnt <= 0) || info->tty->stopped || - (info->tty->hw_stopped && - (info->type != PORT_16550A) && - (!info->IsMoxaMustChipFlag))) { - info->IER &= ~UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - spin_unlock_irqrestore(&info->slock, flags); - return; - } - - cnt = info->xmit_cnt; - count = info->xmit_fifo_size; - do { - outb(info->xmit_buf[info->xmit_tail++], - info->base + UART_TX); - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE - 1); - if (--info->xmit_cnt <= 0) - break; - } while (--count > 0); - mxvar_log.txcnt[info->port] += (cnt - info->xmit_cnt); - -/* added by James 03-12-2004. */ - info->mon_data.txcnt += (cnt - info->xmit_cnt); - info->mon_data.up_txcnt += (cnt - info->xmit_cnt); -/* (above) added by James. */ - -/* added by casper 1/11/2000 */ - info->icount.tx += (cnt - info->xmit_cnt); -/* */ - - if (info->xmit_cnt < WAKEUP_CHARS) { - set_bit(MXSER_EVENT_TXLOW, &info->event); - schedule_work(&info->tqueue); - } - if (info->xmit_cnt <= 0) { - info->IER &= ~UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - } - spin_unlock_irqrestore(&info->slock, flags); -} - -static void mxser_check_modem_status(struct mxser_struct *info, int status) -{ - /* update input line counters */ - if (status & UART_MSR_TERI) - info->icount.rng++; - if (status & UART_MSR_DDSR) - info->icount.dsr++; - if (status & UART_MSR_DDCD) - info->icount.dcd++; - if (status & UART_MSR_DCTS) - info->icount.cts++; - info->mon_data.modem_status = status; - wake_up_interruptible(&info->delta_msr_wait); - - if ((info->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) { - if (status & UART_MSR_DCD) - wake_up_interruptible(&info->open_wait); - schedule_work(&info->tqueue); - } - - if (info->flags & ASYNC_CTS_FLOW) { - if (info->tty->hw_stopped) { - if (status & UART_MSR_CTS) { - info->tty->hw_stopped = 0; - - if ((info->type != PORT_16550A) && - (!info->IsMoxaMustChipFlag)) { - info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - } - set_bit(MXSER_EVENT_TXLOW, &info->event); - schedule_work(&info->tqueue); } - } else { - if (!(status & UART_MSR_CTS)) { - info->tty->hw_stopped = 1; - if ((info->type != PORT_16550A) && - (!info->IsMoxaMustChipFlag)) { - info->IER &= ~UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - } - } - } - } -} - -static int mxser_block_til_ready(struct tty_struct *tty, struct file *filp, struct mxser_struct *info) -{ - DECLARE_WAITQUEUE(wait, current); - int retval; - int do_clocal = 0; - unsigned long flags; - - /* - * If non-blocking mode is set, or the port is not enabled, - * then make the check up front and then exit. - */ - if ((filp->f_flags & O_NONBLOCK) || (tty->flags & (1 << TTY_IO_ERROR))) { - info->flags |= ASYNC_NORMAL_ACTIVE; - return 0; - } - - if (tty->termios->c_cflag & CLOCAL) - do_clocal = 1; - - /* - * Block waiting for the carrier detect and the line to become - * free (i.e., not in use by the callout). While we are in - * this loop, info->count is dropped by one, so that - * mxser_close() knows when to free things. We restore it upon - * exit, either normal or abnormal. - */ - retval = 0; - add_wait_queue(&info->open_wait, &wait); - - spin_lock_irqsave(&info->slock, flags); - if (!tty_hung_up_p(filp)) - info->count--; - spin_unlock_irqrestore(&info->slock, flags); - info->blocked_open++; - while (1) { - spin_lock_irqsave(&info->slock, flags); - outb(inb(info->base + UART_MCR) | - UART_MCR_DTR | UART_MCR_RTS, info->base + UART_MCR); - spin_unlock_irqrestore(&info->slock, flags); - set_current_state(TASK_INTERRUPTIBLE); - if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)) { - if (info->flags & ASYNC_HUP_NOTIFY) - retval = -EAGAIN; - else - retval = -ERESTARTSYS; - break; - } - if (!(info->flags & ASYNC_CLOSING) && - (do_clocal || - (inb(info->base + UART_MSR) & UART_MSR_DCD))) - break; - if (signal_pending(current)) { - retval = -ERESTARTSYS; - break; - } - schedule(); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&info->open_wait, &wait); - if (!tty_hung_up_p(filp)) - info->count++; - info->blocked_open--; - if (retval) - return retval; - info->flags |= ASYNC_NORMAL_ACTIVE; - return 0; -} - -static int mxser_startup(struct mxser_struct *info) -{ - unsigned long page; - unsigned long flags; - - page = __get_free_page(GFP_KERNEL); - if (!page) - return -ENOMEM; - - spin_lock_irqsave(&info->slock, flags); - - if (info->flags & ASYNC_INITIALIZED) { - free_page(page); - spin_unlock_irqrestore(&info->slock, flags); - return 0; - } - - if (!info->base || !info->type) { - if (info->tty) - set_bit(TTY_IO_ERROR, &info->tty->flags); - free_page(page); - spin_unlock_irqrestore(&info->slock, flags); - return 0; - } - if (info->xmit_buf) - free_page(page); - else - info->xmit_buf = (unsigned char *) page; - - /* - * Clear the FIFO buffers and disable them - * (they will be reenabled in mxser_change_speed()) - */ - if (info->IsMoxaMustChipFlag) - outb((UART_FCR_CLEAR_RCVR | - UART_FCR_CLEAR_XMIT | - MOXA_MUST_FCR_GDA_MODE_ENABLE), info->base + UART_FCR); - else - outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), - info->base + UART_FCR); - - /* - * At this point there's no way the LSR could still be 0xFF; - * if it is, then bail out, because there's likely no UART - * here. - */ - if (inb(info->base + UART_LSR) == 0xff) { - spin_unlock_irqrestore(&info->slock, flags); - if (capable(CAP_SYS_ADMIN)) { - if (info->tty) - set_bit(TTY_IO_ERROR, &info->tty->flags); - return 0; - } else - return -ENODEV; - } - - /* - * Clear the interrupt registers. - */ - (void) inb(info->base + UART_LSR); - (void) inb(info->base + UART_RX); - (void) inb(info->base + UART_IIR); - (void) inb(info->base + UART_MSR); - - /* - * Now, initialize the UART - */ - outb(UART_LCR_WLEN8, info->base + UART_LCR); /* reset DLAB */ - info->MCR = UART_MCR_DTR | UART_MCR_RTS; - outb(info->MCR, info->base + UART_MCR); - - /* - * Finally, enable interrupts - */ - info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; - /* info->IER = UART_IER_RLSI | UART_IER_RDI; */ - - /* following add by Victor Yu. 08-30-2002 */ - if (info->IsMoxaMustChipFlag) - info->IER |= MOXA_MUST_IER_EGDAI; - /* above add by Victor Yu. 08-30-2002 */ - outb(info->IER, info->base + UART_IER); /* enable interrupts */ - - /* - * And clear the interrupt registers again for luck. - */ - (void) inb(info->base + UART_LSR); - (void) inb(info->base + UART_RX); - (void) inb(info->base + UART_IIR); - (void) inb(info->base + UART_MSR); - - if (info->tty) - clear_bit(TTY_IO_ERROR, &info->tty->flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - - /* - * and set the speed of the serial port - */ - spin_unlock_irqrestore(&info->slock, flags); - mxser_change_speed(info, NULL); - - info->flags |= ASYNC_INITIALIZED; - return 0; -} - -/* - * This routine will shutdown a serial port; interrupts maybe disabled, and - * DTR is dropped if the hangup on close termio flag is on. - */ -static void mxser_shutdown(struct mxser_struct *info) -{ - unsigned long flags; - - if (!(info->flags & ASYNC_INITIALIZED)) - return; - - spin_lock_irqsave(&info->slock, flags); - - /* - * clear delta_msr_wait queue to avoid mem leaks: we may free the irq - * here so the queue might never be waken up - */ - wake_up_interruptible(&info->delta_msr_wait); - - /* - * Free the IRQ, if necessary - */ - if (info->xmit_buf) { - free_page((unsigned long) info->xmit_buf); - info->xmit_buf = NULL; - } - - info->IER = 0; - outb(0x00, info->base + UART_IER); - - if (!info->tty || (info->tty->termios->c_cflag & HUPCL)) - info->MCR &= ~(UART_MCR_DTR | UART_MCR_RTS); - outb(info->MCR, info->base + UART_MCR); - - /* clear Rx/Tx FIFO's */ - /* following add by Victor Yu. 08-30-2002 */ - if (info->IsMoxaMustChipFlag) - outb((UART_FCR_CLEAR_RCVR | - UART_FCR_CLEAR_XMIT | - MOXA_MUST_FCR_GDA_MODE_ENABLE), info->base + UART_FCR); - else - /* above add by Victor Yu. 08-30-2002 */ - outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), - info->base + UART_FCR); - - /* read data port to reset things */ - (void) inb(info->base + UART_RX); - - if (info->tty) - set_bit(TTY_IO_ERROR, &info->tty->flags); - - info->flags &= ~ASYNC_INITIALIZED; - - /* following add by Victor Yu. 09-23-2002 */ - if (info->IsMoxaMustChipFlag) - SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->base); - /* above add by Victor Yu. 09-23-2002 */ - - spin_unlock_irqrestore(&info->slock, flags); -} - -/* - * This routine is called to set the UART divisor registers to match - * the specified baud rate for a serial port. - */ -static int mxser_change_speed(struct mxser_struct *info, struct ktermios *old_termios) -{ - unsigned cflag, cval, fcr; - int ret = 0; - unsigned char status; - long baud; - unsigned long flags; - - if (!info->tty || !info->tty->termios) - return ret; - cflag = info->tty->termios->c_cflag; - if (!(info->base)) - return ret; - -#ifndef B921600 -#define B921600 (B460800 +1) -#endif - if (mxser_set_baud_method[info->port] == 0) { - baud = tty_get_baud_rate(info->tty); - if (mxser_set_baud(info, baud) == -1) { - /* Use previous rate on a failure */ - if (old_termios) { - baud = tty_termios_baud_rate(old_termios); - tty_encode_baud_rate(info->tty, baud, baud); - } - } - } - - /* byte size and parity */ - switch (cflag & CSIZE) { - case CS5: - cval = 0x00; - break; - case CS6: - cval = 0x01; - break; - case CS7: - cval = 0x02; - break; - case CS8: - cval = 0x03; - break; - default: - cval = 0x00; - break; /* too keep GCC shut... */ - } - if (cflag & CSTOPB) - cval |= 0x04; - if (cflag & PARENB) - cval |= UART_LCR_PARITY; - if (!(cflag & PARODD)) - cval |= UART_LCR_EPAR; - if (cflag & CMSPAR) - cval |= UART_LCR_SPAR; - - if ((info->type == PORT_8250) || (info->type == PORT_16450)) { - if (info->IsMoxaMustChipFlag) { - fcr = UART_FCR_ENABLE_FIFO; - fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; - SET_MOXA_MUST_FIFO_VALUE(info); - } else - fcr = 0; - } else { - fcr = UART_FCR_ENABLE_FIFO; - /* following add by Victor Yu. 08-30-2002 */ - if (info->IsMoxaMustChipFlag) { - fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; - SET_MOXA_MUST_FIFO_VALUE(info); - } else { - /* above add by Victor Yu. 08-30-2002 */ - switch (info->rx_trigger) { - case 1: - fcr |= UART_FCR_TRIGGER_1; - break; - case 4: - fcr |= UART_FCR_TRIGGER_4; - break; - case 8: - fcr |= UART_FCR_TRIGGER_8; - break; - default: - fcr |= UART_FCR_TRIGGER_14; - break; - } - } - } - - /* CTS flow control flag and modem status interrupts */ - info->IER &= ~UART_IER_MSI; - info->MCR &= ~UART_MCR_AFE; - if (cflag & CRTSCTS) { - info->flags |= ASYNC_CTS_FLOW; - info->IER |= UART_IER_MSI; - if ((info->type == PORT_16550A) || (info->IsMoxaMustChipFlag)) { - info->MCR |= UART_MCR_AFE; - } else { - status = inb(info->base + UART_MSR); - if (info->tty->hw_stopped) { - if (status & UART_MSR_CTS) { - info->tty->hw_stopped = 0; - if ((info->type != PORT_16550A) && - (!info->IsMoxaMustChipFlag)) { - info->IER |= UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - } - set_bit(MXSER_EVENT_TXLOW, &info->event); - schedule_work(&info->tqueue); } - } else { - if (!(status & UART_MSR_CTS)) { - info->tty->hw_stopped = 1; - if ((info->type != PORT_16550A) && - (!info->IsMoxaMustChipFlag)) { - info->IER &= ~UART_IER_THRI; - outb(info->IER, info->base + UART_IER); - } - } - } - } - } else { - info->flags &= ~ASYNC_CTS_FLOW; - } - outb(info->MCR, info->base + UART_MCR); - if (cflag & CLOCAL) { - info->flags &= ~ASYNC_CHECK_CD; - } else { - info->flags |= ASYNC_CHECK_CD; - info->IER |= UART_IER_MSI; - } - outb(info->IER, info->base + UART_IER); - - /* - * Set up parity check flag - */ - info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; - if (I_INPCK(info->tty)) - info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (I_BRKINT(info->tty) || I_PARMRK(info->tty)) - info->read_status_mask |= UART_LSR_BI; - - info->ignore_status_mask = 0; - - if (I_IGNBRK(info->tty)) { - info->ignore_status_mask |= UART_LSR_BI; - info->read_status_mask |= UART_LSR_BI; - /* - * If we're ignore parity and break indicators, ignore - * overruns too. (For real raw support). - */ - if (I_IGNPAR(info->tty)) { - info->ignore_status_mask |= - UART_LSR_OE | - UART_LSR_PE | - UART_LSR_FE; - info->read_status_mask |= - UART_LSR_OE | - UART_LSR_PE | - UART_LSR_FE; - } - } - /* following add by Victor Yu. 09-02-2002 */ - if (info->IsMoxaMustChipFlag) { - spin_lock_irqsave(&info->slock, flags); - SET_MOXA_MUST_XON1_VALUE(info->base, START_CHAR(info->tty)); - SET_MOXA_MUST_XOFF1_VALUE(info->base, STOP_CHAR(info->tty)); - if (I_IXON(info->tty)) { - ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->base); - } else { - DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->base); - } - if (I_IXOFF(info->tty)) { - ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->base); - } else { - DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->base); - } - /* - if ( I_IXANY(info->tty) ) { - info->MCR |= MOXA_MUST_MCR_XON_ANY; - ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(info->base); - } else { - info->MCR &= ~MOXA_MUST_MCR_XON_ANY; - DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(info->base); - } - */ - spin_unlock_irqrestore(&info->slock, flags); + break; + if (timeout && time_after(jiffies, orig_jiffies + timeout)) + break; } - /* above add by Victor Yu. 09-02-2002 */ + set_current_state(TASK_RUNNING); +#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT + printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); +#endif +} - outb(fcr, info->base + UART_FCR); /* set fcr */ - outb(cval, info->base + UART_LCR); +/* + * This routine is called by tty_hangup() when a hangup is signaled. + */ +static void mxser_hangup(struct tty_struct *tty) +{ + struct mxser_port *info = tty->driver_data; - return ret; + mxser_flush_buffer(tty); + mxser_shutdown(info); + info->event = 0; + info->count = 0; + info->flags &= ~ASYNC_NORMAL_ACTIVE; + info->tty = NULL; + wake_up_interruptible(&info->open_wait); } - -static int mxser_set_baud(struct mxser_struct *info, long newspd) +/* + * mxser_rs_break() --- routine which turns the break handling on or off + */ +static void mxser_rs_break(struct tty_struct *tty, int break_state) { - int quot = 0; - unsigned char cval; + struct mxser_port *info = tty->driver_data; unsigned long flags; - unsigned int baud; - if (!info->tty || !info->tty->termios) - return -1; + spin_lock_irqsave(&info->slock, flags); + if (break_state == -1) + outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC, + info->ioaddr + UART_LCR); + else + outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC, + info->ioaddr + UART_LCR); + spin_unlock_irqrestore(&info->slock, flags); +} - if (!(info->base)) - return -1; +static void mxser_receive_chars(struct mxser_port *port, int *status) +{ + struct tty_struct *tty = port->tty; + unsigned char ch, gdl; + int ignored = 0; + int cnt = 0; + int recv_room; + int max = 256; - if (newspd > info->MaxCanSetBaudRate) - return -1; + recv_room = tty->receive_room; + if ((recv_room == 0) && (!port->ldisc_stop_rx)) + mxser_stoprx(tty); - info->realbaud = newspd; - if (newspd == 134) { - quot = (2 * info->baud_base / 269); - tty_encode_baud_rate(info->tty, 134, 134); - } else if (newspd) { - quot = info->baud_base / newspd; - if (quot == 0) - quot = 1; - baud = info->baud_base / quot; - tty_encode_baud_rate(info->tty, baud, baud); - } else { - quot = 0; - tty_encode_baud_rate(info->tty, 0, 0); - } + if (port->board->chip_flag != MOXA_OTHER_UART) { - info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base); - info->timeout += HZ / 50; /* Add .02 seconds of slop */ + if (*status & UART_LSR_SPECIAL) + goto intr_old; + if (port->board->chip_flag == MOXA_MUST_MU860_HWID && + (*status & MOXA_MUST_LSR_RERR)) + goto intr_old; + if (*status & MOXA_MUST_LSR_RERR) + goto intr_old; - if (quot) { - spin_lock_irqsave(&info->slock, flags); - info->MCR |= UART_MCR_DTR; - outb(info->MCR, info->base + UART_MCR); - spin_unlock_irqrestore(&info->slock, flags); - } else { - spin_lock_irqsave(&info->slock, flags); - info->MCR &= ~UART_MCR_DTR; - outb(info->MCR, info->base + UART_MCR); - spin_unlock_irqrestore(&info->slock, flags); - return 0; + gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER); + + if (port->board->chip_flag == MOXA_MUST_MU150_HWID) + gdl &= MOXA_MUST_GDL_MASK; + if (gdl >= recv_room) { + if (!port->ldisc_stop_rx) + mxser_stoprx(tty); + } + while (gdl--) { + ch = inb(port->ioaddr + UART_RX); + tty_insert_flip_char(tty, ch, 0); + cnt++; + } + goto end_intr; } +intr_old: + + do { + if (max-- < 0) + break; - cval = inb(info->base + UART_LCR); + ch = inb(port->ioaddr + UART_RX); + if (port->board->chip_flag && (*status & UART_LSR_OE)) + outb(0x23, port->ioaddr + UART_FCR); + *status &= port->read_status_mask; + if (*status & port->ignore_status_mask) { + if (++ignored > 100) + break; + } else { + char flag = 0; + if (*status & UART_LSR_SPECIAL) { + if (*status & UART_LSR_BI) { + flag = TTY_BREAK; + port->icount.brk++; - outb(cval | UART_LCR_DLAB, info->base + UART_LCR); /* set DLAB */ + if (port->flags & ASYNC_SAK) + do_SAK(tty); + } else if (*status & UART_LSR_PE) { + flag = TTY_PARITY; + port->icount.parity++; + } else if (*status & UART_LSR_FE) { + flag = TTY_FRAME; + port->icount.frame++; + } else if (*status & UART_LSR_OE) { + flag = TTY_OVERRUN; + port->icount.overrun++; + } else + flag = TTY_BREAK; + } + tty_insert_flip_char(tty, ch, flag); + cnt++; + if (cnt >= recv_room) { + if (!port->ldisc_stop_rx) + mxser_stoprx(tty); + break; + } - outb(quot & 0xff, info->base + UART_DLL); /* LS of divisor */ - outb(quot >> 8, info->base + UART_DLM); /* MS of divisor */ - outb(cval, info->base + UART_LCR); /* reset DLAB */ + } + if (port->board->chip_flag) + break; - return 0; -} + *status = inb(port->ioaddr + UART_LSR); + } while (*status & UART_LSR_DR); -/* - * ------------------------------------------------------------ - * friends of mxser_ioctl() - * ------------------------------------------------------------ - */ -static int mxser_get_serial_info(struct mxser_struct *info, struct serial_struct __user *retinfo) -{ - struct serial_struct tmp; +end_intr: + mxvar_log.rxcnt[port->tty->index] += cnt; + port->mon_data.rxcnt += cnt; + port->mon_data.up_rxcnt += cnt; - if (!retinfo) - return -EFAULT; - memset(&tmp, 0, sizeof(tmp)); - tmp.type = info->type; - tmp.line = info->port; - tmp.port = info->base; - tmp.irq = info->irq; - tmp.flags = info->flags; - tmp.baud_base = info->baud_base; - tmp.close_delay = info->close_delay; - tmp.closing_wait = info->closing_wait; - tmp.custom_divisor = info->custom_divisor; - tmp.hub6 = 0; - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) - return -EFAULT; - return 0; + /* + * We are called from an interrupt context with &port->slock + * being held. Drop it temporarily in order to prevent + * recursive locking. + */ + spin_unlock(&port->slock); + tty_flip_buffer_push(tty); + spin_lock(&port->slock); } -static int mxser_set_serial_info(struct mxser_struct *info, struct serial_struct __user *new_info) +static void mxser_transmit_chars(struct mxser_port *port) { - struct serial_struct new_serial; - unsigned int flags; - int retval = 0; - - if (!new_info || !info->base) - return -EFAULT; - if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) - return -EFAULT; + int count, cnt; - if ((new_serial.irq != info->irq) || - (new_serial.port != info->base) || - (new_serial.custom_divisor != info->custom_divisor) || - (new_serial.baud_base != info->baud_base)) - return -EPERM; + if (port->x_char) { + outb(port->x_char, port->ioaddr + UART_TX); + port->x_char = 0; + mxvar_log.txcnt[port->tty->index]++; + port->mon_data.txcnt++; + port->mon_data.up_txcnt++; + port->icount.tx++; + return; + } - flags = info->flags & ASYNC_SPD_MASK; + if (port->xmit_buf == NULL) + return; - if (!capable(CAP_SYS_ADMIN)) { - if ((new_serial.baud_base != info->baud_base) || - (new_serial.close_delay != info->close_delay) || - ((new_serial.flags & ~ASYNC_USR_MASK) != (info->flags & ~ASYNC_USR_MASK))) - return -EPERM; - info->flags = ((info->flags & ~ASYNC_USR_MASK) | - (new_serial.flags & ASYNC_USR_MASK)); - } else { - /* - * OK, past this point, all the error checking has been done. - * At this point, we start making changes..... - */ - info->flags = ((info->flags & ~ASYNC_FLAGS) | - (new_serial.flags & ASYNC_FLAGS)); - info->close_delay = new_serial.close_delay * HZ / 100; - info->closing_wait = new_serial.closing_wait * HZ / 100; - info->tty->low_latency = - (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; - info->tty->low_latency = 0; /* (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; */ + if ((port->xmit_cnt <= 0) || port->tty->stopped || + (port->tty->hw_stopped && + (port->type != PORT_16550A) && + (!port->board->chip_flag))) { + port->IER &= ~UART_IER_THRI; + outb(port->IER, port->ioaddr + UART_IER); + return; } - /* added by casper, 3/17/2000, for mouse */ - info->type = new_serial.type; + cnt = port->xmit_cnt; + count = port->xmit_fifo_size; + do { + outb(port->xmit_buf[port->xmit_tail++], + port->ioaddr + UART_TX); + port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1); + if (--port->xmit_cnt <= 0) + break; + } while (--count > 0); + mxvar_log.txcnt[port->tty->index] += (cnt - port->xmit_cnt); - process_txrx_fifo(info); + port->mon_data.txcnt += (cnt - port->xmit_cnt); + port->mon_data.up_txcnt += (cnt - port->xmit_cnt); + port->icount.tx += (cnt - port->xmit_cnt); - if (info->flags & ASYNC_INITIALIZED) { - if (flags != (info->flags & ASYNC_SPD_MASK)) { - mxser_change_speed(info, NULL); - } - } else { - retval = mxser_startup(info); + if (port->xmit_cnt < WAKEUP_CHARS) + tty_wakeup(port->tty); + + if (port->xmit_cnt <= 0) { + port->IER &= ~UART_IER_THRI; + outb(port->IER, port->ioaddr + UART_IER); } - return retval; } /* - * mxser_get_lsr_info - get line status register info - * - * Purpose: Let user call ioctl() to get info when the UART physically - * is emptied. On bus types like RS485, the transmitter must - * release the bus after transmitting. This must be done when - * the transmit shift register is empty, not be done when the - * transmit holding register is empty. This functionality - * allows an RS485 driver to be written in user space. + * This is the serial driver's generic interrupt routine */ -static int mxser_get_lsr_info(struct mxser_struct *info, unsigned int __user *value) +static irqreturn_t mxser_interrupt(int irq, void *dev_id) { - unsigned char status; - unsigned int result; - unsigned long flags; + int status, iir, i; + struct mxser_board *brd = NULL; + struct mxser_port *port; + int max, irqbits, bits, msr; + unsigned int int_cnt, pass_counter = 0; + int handled = IRQ_NONE; - spin_lock_irqsave(&info->slock, flags); - status = inb(info->base + UART_LSR); - spin_unlock_irqrestore(&info->slock, flags); - result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); - return put_user(result, value); -} + for (i = 0; i < MXSER_BOARDS; i++) + if (dev_id == &mxser_boards[i]) { + brd = dev_id; + break; + } -/* - * This routine sends a break character out the serial port. - */ -static void mxser_send_break(struct mxser_struct *info, int duration) -{ - unsigned long flags; + if (i == MXSER_BOARDS) + goto irq_stop; + if (brd == NULL) + goto irq_stop; + max = brd->info->nports; + while (pass_counter++ < MXSER_ISR_PASS_LIMIT) { + irqbits = inb(brd->vector) & brd->vector_mask; + if (irqbits == brd->vector_mask) + break; - if (!info->base) - return; - set_current_state(TASK_INTERRUPTIBLE); - spin_lock_irqsave(&info->slock, flags); - outb(inb(info->base + UART_LCR) | UART_LCR_SBC, - info->base + UART_LCR); - spin_unlock_irqrestore(&info->slock, flags); - schedule_timeout(duration); - spin_lock_irqsave(&info->slock, flags); - outb(inb(info->base + UART_LCR) & ~UART_LCR_SBC, - info->base + UART_LCR); - spin_unlock_irqrestore(&info->slock, flags); -} + handled = IRQ_HANDLED; + for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) { + if (irqbits == brd->vector_mask) + break; + if (bits & irqbits) + continue; + port = &brd->ports[i]; + + int_cnt = 0; + spin_lock(&port->slock); + do { + iir = inb(port->ioaddr + UART_IIR); + if (iir & UART_IIR_NO_INT) + break; + iir &= MOXA_MUST_IIR_MASK; + if (!port->tty || + (port->flags & ASYNC_CLOSING) || + !(port->flags & + ASYNC_INITIALIZED)) { + status = inb(port->ioaddr + UART_LSR); + outb(0x27, port->ioaddr + UART_FCR); + inb(port->ioaddr + UART_MSR); + break; + } -static int mxser_tiocmget(struct tty_struct *tty, struct file *file) -{ - struct mxser_struct *info = tty->driver_data; - unsigned char control, status; - unsigned long flags; + status = inb(port->ioaddr + UART_LSR); + + if (status & UART_LSR_PE) + port->err_shadow |= NPPI_NOTIFY_PARITY; + if (status & UART_LSR_FE) + port->err_shadow |= NPPI_NOTIFY_FRAMING; + if (status & UART_LSR_OE) + port->err_shadow |= + NPPI_NOTIFY_HW_OVERRUN; + if (status & UART_LSR_BI) + port->err_shadow |= NPPI_NOTIFY_BREAK; + + if (port->board->chip_flag) { + if (iir == MOXA_MUST_IIR_GDA || + iir == MOXA_MUST_IIR_RDA || + iir == MOXA_MUST_IIR_RTO || + iir == MOXA_MUST_IIR_LSR) + mxser_receive_chars(port, + &status); + + } else { + status &= port->read_status_mask; + if (status & UART_LSR_DR) + mxser_receive_chars(port, + &status); + } + msr = inb(port->ioaddr + UART_MSR); + if (msr & UART_MSR_ANY_DELTA) + mxser_check_modem_status(port, msr); + + if (port->board->chip_flag) { + if (iir == 0x02 && (status & + UART_LSR_THRE)) + mxser_transmit_chars(port); + } else { + if (status & UART_LSR_THRE) + mxser_transmit_chars(port); + } + } while (int_cnt++ < MXSER_ISR_PASS_LIMIT); + spin_unlock(&port->slock); + } + } +irq_stop: + return handled; +} - if (tty->index == MXSER_PORTS) - return -ENOIOCTLCMD; - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; +static const struct tty_operations mxser_ops = { + .open = mxser_open, + .close = mxser_close, + .write = mxser_write, + .put_char = mxser_put_char, + .flush_chars = mxser_flush_chars, + .write_room = mxser_write_room, + .chars_in_buffer = mxser_chars_in_buffer, + .flush_buffer = mxser_flush_buffer, + .ioctl = mxser_ioctl, + .throttle = mxser_throttle, + .unthrottle = mxser_unthrottle, + .set_termios = mxser_set_termios, + .stop = mxser_stop, + .start = mxser_start, + .hangup = mxser_hangup, + .break_ctl = mxser_rs_break, + .wait_until_sent = mxser_wait_until_sent, + .tiocmget = mxser_tiocmget, + .tiocmset = mxser_tiocmset, +}; - control = info->MCR; +/* + * The MOXA Smartio/Industio serial driver boot-time initialization code! + */ - spin_lock_irqsave(&info->slock, flags); - status = inb(info->base + UART_MSR); - if (status & UART_MSR_ANY_DELTA) - mxser_check_modem_status(info, status); - spin_unlock_irqrestore(&info->slock, flags); - return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) | - ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) | - ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) | - ((status & UART_MSR_RI) ? TIOCM_RNG : 0) | - ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) | - ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); +static void mxser_release_res(struct mxser_board *brd, struct pci_dev *pdev, + unsigned int irq) +{ + if (irq) + free_irq(brd->irq, brd); + if (pdev != NULL) { /* PCI */ +#ifdef CONFIG_PCI + pci_release_region(pdev, 2); + pci_release_region(pdev, 3); +#endif + } else { + release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); + release_region(brd->vector, 1); + } } -static int mxser_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear) +static int __devinit mxser_initbrd(struct mxser_board *brd, + struct pci_dev *pdev) { - struct mxser_struct *info = tty->driver_data; - unsigned long flags; + struct mxser_port *info; + unsigned int i; + int retval; + printk(KERN_INFO "max. baud rate = %d bps.\n", brd->ports[0].max_baud); - if (tty->index == MXSER_PORTS) - return -ENOIOCTLCMD; - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; + for (i = 0; i < brd->info->nports; i++) { + info = &brd->ports[i]; + info->board = brd; + info->stop_rx = 0; + info->ldisc_stop_rx = 0; - spin_lock_irqsave(&info->slock, flags); + /* Enhance mode enabled here */ + if (brd->chip_flag != MOXA_OTHER_UART) + ENABLE_MOXA_MUST_ENCHANCE_MODE(info->ioaddr); - if (set & TIOCM_RTS) - info->MCR |= UART_MCR_RTS; - if (set & TIOCM_DTR) - info->MCR |= UART_MCR_DTR; + info->flags = ASYNC_SHARE_IRQ; + info->type = brd->uart_type; - if (clear & TIOCM_RTS) - info->MCR &= ~UART_MCR_RTS; - if (clear & TIOCM_DTR) - info->MCR &= ~UART_MCR_DTR; + process_txrx_fifo(info); - outb(info->MCR, info->base + UART_MCR); - spin_unlock_irqrestore(&info->slock, flags); - return 0; -} + info->custom_divisor = info->baud_base * 16; + info->close_delay = 5 * HZ / 10; + info->closing_wait = 30 * HZ; + info->normal_termios = mxvar_sdriver->init_termios; + init_waitqueue_head(&info->open_wait); + init_waitqueue_head(&info->delta_msr_wait); + memset(&info->mon_data, 0, sizeof(struct mxser_mon)); + info->err_shadow = 0; + spin_lock_init(&info->slock); + /* before set INT ISR, disable all int */ + outb(inb(info->ioaddr + UART_IER) & 0xf0, + info->ioaddr + UART_IER); + } -static int mxser_read_register(int, unsigned short *); -static int mxser_program_mode(int); -static void mxser_normal_mode(int); + retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser", + brd); + if (retval) { + printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may " + "conflict with another device.\n", + brd->info->name, brd->irq); + /* We hold resources, we need to release them. */ + mxser_release_res(brd, pdev, 0); + } + return retval; +} -static int mxser_get_ISA_conf(int cap, struct mxser_hwconf *hwconf) +static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd) { int id, i, bits; unsigned short regs[16], irq; unsigned char scratch, scratch2; - hwconf->IsMoxaMustChipFlag = MOXA_OTHER_UART; + brd->chip_flag = MOXA_OTHER_UART; id = mxser_read_register(cap, regs); - if (id == C168_ASIC_ID) { - hwconf->board_type = MXSER_BOARD_C168_ISA; - hwconf->ports = 8; - } else if (id == C104_ASIC_ID) { - hwconf->board_type = MXSER_BOARD_C104_ISA; - hwconf->ports = 4; - } else if (id == C102_ASIC_ID) { - hwconf->board_type = MXSER_BOARD_C102_ISA; - hwconf->ports = 2; - } else if (id == CI132_ASIC_ID) { - hwconf->board_type = MXSER_BOARD_CI132; - hwconf->ports = 2; - } else if (id == CI134_ASIC_ID) { - hwconf->board_type = MXSER_BOARD_CI134; - hwconf->ports = 4; - } else if (id == CI104J_ASIC_ID) { - hwconf->board_type = MXSER_BOARD_CI104J; - hwconf->ports = 4; - } else + switch (id) { + case C168_ASIC_ID: + brd->info = &mxser_cards[0]; + break; + case C104_ASIC_ID: + brd->info = &mxser_cards[1]; + break; + case CI104J_ASIC_ID: + brd->info = &mxser_cards[2]; + break; + case C102_ASIC_ID: + brd->info = &mxser_cards[5]; + break; + case CI132_ASIC_ID: + brd->info = &mxser_cards[6]; + break; + case CI134_ASIC_ID: + brd->info = &mxser_cards[7]; + break; + default: return 0; + } irq = 0; - if (hwconf->ports == 2) { + /* some ISA cards have 2 ports, but we want to see them as 4-port (why?) + Flag-hack checks if configuration should be read as 2-port here. */ + if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) { irq = regs[9] & 0xF000; irq = irq | (irq >> 4); if (irq != (regs[9] & 0xFF00)) return MXSER_ERR_IRQ_CONFLIT; - } else if (hwconf->ports == 4) { + } else if (brd->info->nports == 4) { irq = regs[9] & 0xF000; irq = irq | (irq >> 4); irq = irq | (irq >> 8); if (irq != regs[9]) return MXSER_ERR_IRQ_CONFLIT; - } else if (hwconf->ports == 8) { + } else if (brd->info->nports == 8) { irq = regs[9] & 0xF000; irq = irq | (irq >> 4); irq = irq | (irq >> 8); @@ -2991,23 +2423,23 @@ static int mxser_get_ISA_conf(int cap, struct mxser_hwconf *hwconf) if (!irq) return MXSER_ERR_IRQ; - hwconf->irq = ((int)(irq & 0xF000) >> 12); + brd->irq = ((int)(irq & 0xF000) >> 12); for (i = 0; i < 8; i++) - hwconf->ioaddr[i] = (int) regs[i + 1] & 0xFFF8; + brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8; if ((regs[12] & 0x80) == 0) return MXSER_ERR_VECTOR; - hwconf->vector = (int)regs[11]; /* interrupt vector */ + brd->vector = (int)regs[11]; /* interrupt vector */ if (id == 1) - hwconf->vector_mask = 0x00FF; + brd->vector_mask = 0x00FF; else - hwconf->vector_mask = 0x000F; + brd->vector_mask = 0x000F; for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) { if (regs[12] & bits) { - hwconf->baud_base[i] = 921600; - hwconf->MaxCanSetBaudRate[i] = 921600; /* add by Victor Yu. 09-04-2002 */ + brd->ports[i].baud_base = 921600; + brd->ports[i].max_baud = 921600; } else { - hwconf->baud_base[i] = 115200; - hwconf->MaxCanSetBaudRate[i] = 115200; /* add by Victor Yu. 09-04-2002 */ + brd->ports[i].baud_base = 115200; + brd->ports[i].max_baud = 115200; } } scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB); @@ -3018,123 +2450,279 @@ static int mxser_get_ISA_conf(int cap, struct mxser_hwconf *hwconf) scratch = inb(cap + UART_IIR); if (scratch & 0xC0) - hwconf->uart_type = PORT_16550A; + brd->uart_type = PORT_16550A; else - hwconf->uart_type = PORT_16450; - if (id == 1) - hwconf->ports = 8; - else - hwconf->ports = 4; - request_region(hwconf->ioaddr[0], 8 * hwconf->ports, "mxser(IO)"); - request_region(hwconf->vector, 1, "mxser(vector)"); - return hwconf->ports; + brd->uart_type = PORT_16450; + if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports, + "mxser(IO)")) + return MXSER_ERR_IOADDR; + if (!request_region(brd->vector, 1, "mxser(vector)")) { + release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); + return MXSER_ERR_VECTOR; + } + return brd->info->nports; } -#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */ -#define CHIP_DO 0x02 /* Serial Data Output in Eprom */ -#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */ -#define CHIP_DI 0x08 /* Serial Data Input in Eprom */ -#define EN_CCMD 0x000 /* Chip's command register */ -#define EN0_RSARLO 0x008 /* Remote start address reg 0 */ -#define EN0_RSARHI 0x009 /* Remote start address reg 1 */ -#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */ -#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */ -#define EN0_DCFG 0x00E /* Data configuration reg WR */ -#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */ -#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */ -#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */ -static int mxser_read_register(int port, unsigned short *regs) +static int __devinit mxser_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) { - int i, k, value, id; - unsigned int j; +#ifdef CONFIG_PCI + struct mxser_board *brd; + unsigned int i, j; + unsigned long ioaddress; + int retval = -EINVAL; - id = mxser_program_mode(port); - if (id < 0) - return id; - for (i = 0; i < 14; i++) { - k = (i & 0x3F) | 0x180; - for (j = 0x100; j > 0; j >>= 1) { - outb(CHIP_CS, port); - if (k & j) { - outb(CHIP_CS | CHIP_DO, port); - outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */ - } else { - outb(CHIP_CS, port); - outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */ + for (i = 0; i < MXSER_BOARDS; i++) + if (mxser_boards[i].info == NULL) + break; + + if (i >= MXSER_BOARDS) { + printk(KERN_ERR "Too many Smartio/Industio family boards found " + "(maximum %d), board not configured\n", MXSER_BOARDS); + goto err; + } + + brd = &mxser_boards[i]; + brd->idx = i * MXSER_PORTS_PER_BOARD; + printk(KERN_INFO "Found MOXA %s board (BusNo=%d, DevNo=%d)\n", + mxser_cards[ent->driver_data].name, + pdev->bus->number, PCI_SLOT(pdev->devfn)); + + retval = pci_enable_device(pdev); + if (retval) { + printk(KERN_ERR "Moxa SmartI/O PCI enable fail !\n"); + goto err; + } + + /* io address */ + ioaddress = pci_resource_start(pdev, 2); + retval = pci_request_region(pdev, 2, "mxser(IO)"); + if (retval) + goto err; + + brd->info = &mxser_cards[ent->driver_data]; + for (i = 0; i < brd->info->nports; i++) + brd->ports[i].ioaddr = ioaddress + 8 * i; + + /* vector */ + ioaddress = pci_resource_start(pdev, 3); + retval = pci_request_region(pdev, 3, "mxser(vector)"); + if (retval) + goto err_relio; + brd->vector = ioaddress; + + /* irq */ + brd->irq = pdev->irq; + + brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr); + brd->uart_type = PORT_16550A; + brd->vector_mask = 0; + + for (i = 0; i < brd->info->nports; i++) { + for (j = 0; j < UART_INFO_NUM; j++) { + if (Gpci_uart_info[j].type == brd->chip_flag) { + brd->ports[i].max_baud = + Gpci_uart_info[j].max_baud; + + /* exception....CP-102 */ + if (brd->info->flags & MXSER_HIGHBAUD) + brd->ports[i].max_baud = 921600; + break; } } - (void)inb(port); - value = 0; - for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) { - outb(CHIP_CS, port); - outb(CHIP_CS | CHIP_SK, port); - if (inb(port) & CHIP_DI) - value |= j; + } + + if (brd->chip_flag == MOXA_MUST_MU860_HWID) { + for (i = 0; i < brd->info->nports; i++) { + if (i < 4) + brd->ports[i].opmode_ioaddr = ioaddress + 4; + else + brd->ports[i].opmode_ioaddr = ioaddress + 0x0c; } - regs[i] = value; - outb(0, port); + outb(0, ioaddress + 4); /* default set to RS232 mode */ + outb(0, ioaddress + 0x0c); /* default set to RS232 mode */ } - mxser_normal_mode(port); - return id; + + for (i = 0; i < brd->info->nports; i++) { + brd->vector_mask |= (1 << i); + brd->ports[i].baud_base = 921600; + } + + /* mxser_initbrd will hook ISR. */ + retval = mxser_initbrd(brd, pdev); + if (retval) + goto err_null; + + for (i = 0; i < brd->info->nports; i++) + tty_register_device(mxvar_sdriver, brd->idx + i, &pdev->dev); + + pci_set_drvdata(pdev, brd); + + return 0; +err_relio: + pci_release_region(pdev, 2); +err_null: + brd->info = NULL; +err: + return retval; +#else + return -ENODEV; +#endif } -static int mxser_program_mode(int port) +static void __devexit mxser_remove(struct pci_dev *pdev) { - int id, i, j, n; - /* unsigned long flags; */ + struct mxser_board *brd = pci_get_drvdata(pdev); + unsigned int i; - spin_lock(&gm_lock); - outb(0, port); - outb(0, port); - outb(0, port); - (void)inb(port); - (void)inb(port); - outb(0, port); - (void)inb(port); - /* restore_flags(flags); */ - spin_unlock(&gm_lock); + for (i = 0; i < brd->info->nports; i++) + tty_unregister_device(mxvar_sdriver, brd->idx + i); - id = inb(port + 1) & 0x1F; - if ((id != C168_ASIC_ID) && - (id != C104_ASIC_ID) && - (id != C102_ASIC_ID) && - (id != CI132_ASIC_ID) && - (id != CI134_ASIC_ID) && - (id != CI104J_ASIC_ID)) - return -1; - for (i = 0, j = 0; i < 4; i++) { - n = inb(port + 2); - if (n == 'M') { - j = 1; - } else if ((j == 1) && (n == 1)) { - j = 2; - break; - } else - j = 0; - } - if (j != 2) - id = -2; - return id; + mxser_release_res(brd, pdev, 1); + brd->info = NULL; } -static void mxser_normal_mode(int port) +static struct pci_driver mxser_driver = { + .name = "mxser", + .id_table = mxser_pcibrds, + .probe = mxser_probe, + .remove = __devexit_p(mxser_remove) +}; + +static int __init mxser_module_init(void) { - int i, n; + struct mxser_board *brd; + unsigned long cap; + unsigned int i, m, isaloop; + int retval, b; - outb(0xA5, port + 1); - outb(0x80, port + 3); - outb(12, port + 0); /* 9600 bps */ - outb(0, port + 1); - outb(0x03, port + 3); /* 8 data bits */ - outb(0x13, port + 4); /* loop back mode */ - for (i = 0; i < 16; i++) { - n = inb(port + 5); - if ((n & 0x61) == 0x60) - break; - if ((n & 1) == 1) - (void)inb(port); + pr_debug("Loading module mxser ...\n"); + + mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1); + if (!mxvar_sdriver) + return -ENOMEM; + + printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n", + MXSER_VERSION); + + /* Initialize the tty_driver structure */ + mxvar_sdriver->owner = THIS_MODULE; + mxvar_sdriver->magic = TTY_DRIVER_MAGIC; + mxvar_sdriver->name = "ttyMI"; + mxvar_sdriver->major = ttymajor; + mxvar_sdriver->minor_start = 0; + mxvar_sdriver->num = MXSER_PORTS + 1; + mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL; + mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL; + mxvar_sdriver->init_termios = tty_std_termios; + mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL; + mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV; + tty_set_operations(mxvar_sdriver, &mxser_ops); + + retval = tty_register_driver(mxvar_sdriver); + if (retval) { + printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family " + "tty driver !\n"); + goto err_put; } - outb(0x00, port + 4); + + mxvar_diagflag = 0; + + m = 0; + /* Start finding ISA boards here */ + for (isaloop = 0; isaloop < 2; isaloop++) + for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) { + if (!isaloop) + cap = mxserBoardCAP[b]; /* predefined */ + else + cap = ioaddr[b]; /* module param */ + + if (!cap) + continue; + + brd = &mxser_boards[m]; + retval = mxser_get_ISA_conf(cap, brd); + + if (retval != 0) + printk(KERN_INFO "Found MOXA %s board " + "(CAP=0x%x)\n", + brd->info->name, ioaddr[b]); + + if (retval <= 0) { + if (retval == MXSER_ERR_IRQ) + printk(KERN_ERR "Invalid interrupt " + "number, board not " + "configured\n"); + else if (retval == MXSER_ERR_IRQ_CONFLIT) + printk(KERN_ERR "Invalid interrupt " + "number, board not " + "configured\n"); + else if (retval == MXSER_ERR_VECTOR) + printk(KERN_ERR "Invalid interrupt " + "vector, board not " + "configured\n"); + else if (retval == MXSER_ERR_IOADDR) + printk(KERN_ERR "Invalid I/O address, " + "board not configured\n"); + + brd->info = NULL; + continue; + } + + /* mxser_initbrd will hook ISR. */ + if (mxser_initbrd(brd, NULL) < 0) { + brd->info = NULL; + continue; + } + + brd->idx = m * MXSER_PORTS_PER_BOARD; + for (i = 0; i < brd->info->nports; i++) + tty_register_device(mxvar_sdriver, brd->idx + i, + NULL); + + m++; + } + + retval = pci_register_driver(&mxser_driver); + if (retval) { + printk(KERN_ERR "Can't register pci driver\n"); + if (!m) { + retval = -ENODEV; + goto err_unr; + } /* else: we have some ISA cards under control */ + } + + pr_debug("Done.\n"); + + return 0; +err_unr: + tty_unregister_driver(mxvar_sdriver); +err_put: + put_tty_driver(mxvar_sdriver); + return retval; +} + +static void __exit mxser_module_exit(void) +{ + unsigned int i, j; + + pr_debug("Unloading module mxser ...\n"); + + pci_unregister_driver(&mxser_driver); + + for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */ + if (mxser_boards[i].info != NULL) + for (j = 0; j < mxser_boards[i].info->nports; j++) + tty_unregister_device(mxvar_sdriver, + mxser_boards[i].idx + j); + tty_unregister_driver(mxvar_sdriver); + put_tty_driver(mxvar_sdriver); + + for (i = 0; i < MXSER_BOARDS; i++) + if (mxser_boards[i].info != NULL) + mxser_release_res(&mxser_boards[i], NULL, 1); + + pr_debug("Done.\n"); } module_init(mxser_module_init); diff --git a/drivers/char/mxser.h b/drivers/char/mxser.h index 1f4aa45ec00..84417111595 100644 --- a/drivers/char/mxser.h +++ b/drivers/char/mxser.h @@ -4,19 +4,17 @@ /* * Semi-public control interfaces */ - + /* * MOXA ioctls */ #define MOXA 0x400 #define MOXA_GETDATACOUNT (MOXA + 23) -#define MOXA_GET_CONF (MOXA + 35) #define MOXA_DIAGNOSE (MOXA + 50) #define MOXA_CHKPORTENABLE (MOXA + 60) #define MOXA_HighSpeedOn (MOXA + 61) #define MOXA_GET_MAJOR (MOXA + 63) -#define MOXA_GET_CUMAJOR (MOXA + 64) #define MOXA_GETMSTATUS (MOXA + 65) #define MOXA_SET_OP_MODE (MOXA + 66) #define MOXA_GET_OP_MODE (MOXA + 67) @@ -26,26 +24,14 @@ #define RS422_MODE 2 #define RS485_4WIRE_MODE 3 #define OP_MODE_MASK 3 -// above add by Victor Yu. 01-05-2004 - -#define TTY_THRESHOLD_THROTTLE 128 - -#define HI_WATER 768 - -// added by James. 03-11-2004. -#define MOXA_SDS_GETICOUNTER (MOXA + 68) -#define MOXA_SDS_RSTICOUNTER (MOXA + 69) -// (above) added by James. +#define MOXA_SDS_RSTICOUNTER (MOXA + 69) #define MOXA_ASPP_OQUEUE (MOXA + 70) -#define MOXA_ASPP_SETBAUD (MOXA + 71) -#define MOXA_ASPP_GETBAUD (MOXA + 72) #define MOXA_ASPP_MON (MOXA + 73) #define MOXA_ASPP_LSTATUS (MOXA + 74) #define MOXA_ASPP_MON_EXT (MOXA + 75) #define MOXA_SET_BAUD_METHOD (MOXA + 76) - /* --------------------------------------------------- */ #define NPPI_NOTIFY_PARITY 0x01 @@ -54,51 +40,46 @@ #define NPPI_NOTIFY_SW_OVERRUN 0x08 #define NPPI_NOTIFY_BREAK 0x10 -#define NPPI_NOTIFY_CTSHOLD 0x01 // Tx hold by CTS low -#define NPPI_NOTIFY_DSRHOLD 0x02 // Tx hold by DSR low -#define NPPI_NOTIFY_XOFFHOLD 0x08 // Tx hold by Xoff received -#define NPPI_NOTIFY_XOFFXENT 0x10 // Xoff Sent - -//CheckIsMoxaMust return value -#define MOXA_OTHER_UART 0x00 -#define MOXA_MUST_MU150_HWID 0x01 -#define MOXA_MUST_MU860_HWID 0x02 - -// follow just for Moxa Must chip define. -// -// when LCR register (offset 0x03) write following value, -// the Must chip will enter enchance mode. And write value -// on EFR (offset 0x02) bit 6,7 to change bank. +#define NPPI_NOTIFY_CTSHOLD 0x01 /* Tx hold by CTS low */ +#define NPPI_NOTIFY_DSRHOLD 0x02 /* Tx hold by DSR low */ +#define NPPI_NOTIFY_XOFFHOLD 0x08 /* Tx hold by Xoff received */ +#define NPPI_NOTIFY_XOFFXENT 0x10 /* Xoff Sent */ + +/* follow just for Moxa Must chip define. */ +/* */ +/* when LCR register (offset 0x03) write following value, */ +/* the Must chip will enter enchance mode. And write value */ +/* on EFR (offset 0x02) bit 6,7 to change bank. */ #define MOXA_MUST_ENTER_ENCHANCE 0xBF -// when enhance mode enable, access on general bank register +/* when enhance mode enable, access on general bank register */ #define MOXA_MUST_GDL_REGISTER 0x07 #define MOXA_MUST_GDL_MASK 0x7F #define MOXA_MUST_GDL_HAS_BAD_DATA 0x80 -#define MOXA_MUST_LSR_RERR 0x80 // error in receive FIFO -// enchance register bank select and enchance mode setting register -// when LCR register equal to 0xBF +#define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */ +/* enchance register bank select and enchance mode setting register */ +/* when LCR register equal to 0xBF */ #define MOXA_MUST_EFR_REGISTER 0x02 -// enchance mode enable +/* enchance mode enable */ #define MOXA_MUST_EFR_EFRB_ENABLE 0x10 -// enchance reister bank set 0, 1, 2 +/* enchance reister bank set 0, 1, 2 */ #define MOXA_MUST_EFR_BANK0 0x00 #define MOXA_MUST_EFR_BANK1 0x40 #define MOXA_MUST_EFR_BANK2 0x80 #define MOXA_MUST_EFR_BANK3 0xC0 #define MOXA_MUST_EFR_BANK_MASK 0xC0 -// set XON1 value register, when LCR=0xBF and change to bank0 +/* set XON1 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XON1_REGISTER 0x04 -// set XON2 value register, when LCR=0xBF and change to bank0 +/* set XON2 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XON2_REGISTER 0x05 -// set XOFF1 value register, when LCR=0xBF and change to bank0 +/* set XOFF1 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XOFF1_REGISTER 0x06 -// set XOFF2 value register, when LCR=0xBF and change to bank0 +/* set XOFF2 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XOFF2_REGISTER 0x07 #define MOXA_MUST_RBRTL_REGISTER 0x04 @@ -110,32 +91,32 @@ #define MOXA_MUST_ECR_REGISTER 0x06 #define MOXA_MUST_CSR_REGISTER 0x07 -// good data mode enable +/* good data mode enable */ #define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20 -// only good data put into RxFIFO +/* only good data put into RxFIFO */ #define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10 -// enable CTS interrupt +/* enable CTS interrupt */ #define MOXA_MUST_IER_ECTSI 0x80 -// enable RTS interrupt +/* enable RTS interrupt */ #define MOXA_MUST_IER_ERTSI 0x40 -// enable Xon/Xoff interrupt +/* enable Xon/Xoff interrupt */ #define MOXA_MUST_IER_XINT 0x20 -// enable GDA interrupt +/* enable GDA interrupt */ #define MOXA_MUST_IER_EGDAI 0x10 #define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI) -// GDA interrupt pending +/* GDA interrupt pending */ #define MOXA_MUST_IIR_GDA 0x1C #define MOXA_MUST_IIR_RDA 0x04 #define MOXA_MUST_IIR_RTO 0x0C #define MOXA_MUST_IIR_LSR 0x06 -// recieved Xon/Xoff or specical interrupt pending +/* recieved Xon/Xoff or specical interrupt pending */ #define MOXA_MUST_IIR_XSC 0x10 -// RTS/CTS change state interrupt pending +/* RTS/CTS change state interrupt pending */ #define MOXA_MUST_IIR_RTSCTS 0x20 #define MOXA_MUST_IIR_MASK 0x3E @@ -143,299 +124,164 @@ #define MOXA_MUST_MCR_XON_ANY 0x80 #define MOXA_MUST_MCR_TX_XON 0x08 - -// software flow control on chip mask value +/* software flow control on chip mask value */ #define MOXA_MUST_EFR_SF_MASK 0x0F -// send Xon1/Xoff1 +/* send Xon1/Xoff1 */ #define MOXA_MUST_EFR_SF_TX1 0x08 -// send Xon2/Xoff2 +/* send Xon2/Xoff2 */ #define MOXA_MUST_EFR_SF_TX2 0x04 -// send Xon1,Xon2/Xoff1,Xoff2 +/* send Xon1,Xon2/Xoff1,Xoff2 */ #define MOXA_MUST_EFR_SF_TX12 0x0C -// don't send Xon/Xoff +/* don't send Xon/Xoff */ #define MOXA_MUST_EFR_SF_TX_NO 0x00 -// Tx software flow control mask +/* Tx software flow control mask */ #define MOXA_MUST_EFR_SF_TX_MASK 0x0C -// don't receive Xon/Xoff +/* don't receive Xon/Xoff */ #define MOXA_MUST_EFR_SF_RX_NO 0x00 -// receive Xon1/Xoff1 +/* receive Xon1/Xoff1 */ #define MOXA_MUST_EFR_SF_RX1 0x02 -// receive Xon2/Xoff2 +/* receive Xon2/Xoff2 */ #define MOXA_MUST_EFR_SF_RX2 0x01 -// receive Xon1,Xon2/Xoff1,Xoff2 +/* receive Xon1,Xon2/Xoff1,Xoff2 */ #define MOXA_MUST_EFR_SF_RX12 0x03 -// Rx software flow control mask +/* Rx software flow control mask */ #define MOXA_MUST_EFR_SF_RX_MASK 0x03 -//#define MOXA_MUST_MIN_XOFFLIMIT 66 -//#define MOXA_MUST_MIN_XONLIMIT 20 -//#define ID1_RX_TRIG 120 - - -#define CHECK_MOXA_MUST_XOFFLIMIT(info) { \ - if ( (info)->IsMoxaMustChipFlag && \ - (info)->HandFlow.XoffLimit < MOXA_MUST_MIN_XOFFLIMIT ) { \ - (info)->HandFlow.XoffLimit = MOXA_MUST_MIN_XOFFLIMIT; \ - (info)->HandFlow.XonLimit = MOXA_MUST_MIN_XONLIMIT; \ - } \ -} - -#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ +#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK0; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) -#define SET_MOXA_MUST_XON2_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ +#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XON2_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK0; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_XOFF2_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XOFF2_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_RBRTL_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_RBRTL_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_RBRTH_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_RBRTH_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_RBRTI_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_FIFO_VALUE(info) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((info)->ioaddr+UART_LCR); \ + outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR);\ + __efr = inb((info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK1; \ + outb(__efr, (info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ + outb((u8)((info)->rx_high_water), (info)->ioaddr+ \ + MOXA_MUST_RBRTH_REGISTER); \ + outb((u8)((info)->rx_trigger), (info)->ioaddr+ \ + MOXA_MUST_RBRTI_REGISTER); \ + outb((u8)((info)->rx_low_water), (info)->ioaddr+ \ + MOXA_MUST_RBRTL_REGISTER); \ + outb(__oldlcr, (info)->ioaddr+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_RBRTI_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_THRTL_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_THRTL_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -//#define MOXA_MUST_RBRL_VALUE 4 -#define SET_MOXA_MUST_FIFO_VALUE(info) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((info)->base+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (info)->base+UART_LCR); \ - __efr = inb((info)->base+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (info)->base+MOXA_MUST_EFR_REGISTER); \ - outb((u8)((info)->rx_high_water), (info)->base+MOXA_MUST_RBRTH_REGISTER); \ - outb((u8)((info)->rx_trigger), (info)->base+MOXA_MUST_RBRTI_REGISTER); \ - outb((u8)((info)->rx_low_water), (info)->base+MOXA_MUST_RBRTL_REGISTER); \ - outb(__oldlcr, (info)->base+UART_LCR); \ -} - - - -#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK2; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) -#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_JUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - __efr |= MOXA_MUST_EFR_SF_TX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ +#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_TX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK2; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_JUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_MASK; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - __efr |= MOXA_MUST_EFR_SF_RX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ + __efr |= MOXA_MUST_EFR_SF_TX1; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_RX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_TX_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ + __efr |= MOXA_MUST_EFR_SF_RX1; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - __efr |= (MOXA_MUST_EFR_SF_RX1|MOXA_MUST_EFR_SF_TX1); \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \ - u8 __oldmcr; \ - __oldmcr = inb((baseio)+UART_MCR); \ - __oldmcr |= MOXA_MUST_MCR_XON_ANY; \ - outb(__oldmcr, (baseio)+UART_MCR); \ -} - -#define DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \ - u8 __oldmcr; \ - __oldmcr = inb((baseio)+UART_MCR); \ - __oldmcr &= ~MOXA_MUST_MCR_XON_ANY; \ - outb(__oldmcr, (baseio)+UART_MCR); \ -} - -#define READ_MOXA_MUST_GDL(baseio) inb((baseio)+MOXA_MUST_GDL_REGISTER) + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) #endif diff --git a/drivers/char/mxser_new.c b/drivers/char/mxser_new.c deleted file mode 100644 index 5c5d246a426..00000000000 --- a/drivers/char/mxser_new.c +++ /dev/null @@ -1,2729 +0,0 @@ -/* - * mxser.c -- MOXA Smartio/Industio family multiport serial driver. - * - * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com.tw). - * Copyright (C) 2006-2007 Jiri Slaby - * - * This code is loosely based on the 1.8 moxa driver which is based on - * Linux serial driver, written by Linus Torvalds, Theodore T'so and - * others. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox - * . The original 1.8 code is available on www.moxa.com. - * - Fixed x86_64 cleanness - * - Fixed sleep with spinlock held in mxser_send_break - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include "mxser_new.h" - -#define MXSER_VERSION "2.0.2" /* 1.10 */ -#define MXSERMAJOR 174 -#define MXSERCUMAJOR 175 - -#define MXSER_BOARDS 4 /* Max. boards */ -#define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */ -#define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD) -#define MXSER_ISR_PASS_LIMIT 100 - -#define MXSER_ERR_IOADDR -1 -#define MXSER_ERR_IRQ -2 -#define MXSER_ERR_IRQ_CONFLIT -3 -#define MXSER_ERR_VECTOR -4 - -/*CheckIsMoxaMust return value*/ -#define MOXA_OTHER_UART 0x00 -#define MOXA_MUST_MU150_HWID 0x01 -#define MOXA_MUST_MU860_HWID 0x02 - -#define WAKEUP_CHARS 256 - -#define UART_MCR_AFE 0x20 -#define UART_LSR_SPECIAL 0x1E - -#define PCI_DEVICE_ID_CB108 0x1080 -#define PCI_DEVICE_ID_CB114 0x1142 -#define PCI_DEVICE_ID_CB134I 0x1341 -#define PCI_DEVICE_ID_CP138U 0x1380 -#define PCI_DEVICE_ID_POS104UL 0x1044 - - -#define C168_ASIC_ID 1 -#define C104_ASIC_ID 2 -#define C102_ASIC_ID 0xB -#define CI132_ASIC_ID 4 -#define CI134_ASIC_ID 3 -#define CI104J_ASIC_ID 5 - -#define MXSER_HIGHBAUD 1 -#define MXSER_HAS2 2 - -/* This is only for PCI */ -static const struct { - int type; - int tx_fifo; - int rx_fifo; - int xmit_fifo_size; - int rx_high_water; - int rx_trigger; - int rx_low_water; - long max_baud; -} Gpci_uart_info[] = { - {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L}, - {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L}, - {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L} -}; -#define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info) - -struct mxser_cardinfo { - char *name; - unsigned int nports; - unsigned int flags; -}; - -static const struct mxser_cardinfo mxser_cards[] = { -/* 0*/ { "C168 series", 8, }, - { "C104 series", 4, }, - { "CI-104J series", 4, }, - { "C168H/PCI series", 8, }, - { "C104H/PCI series", 4, }, -/* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */ - { "CI-132 series", 4, MXSER_HAS2 }, - { "CI-134 series", 4, }, - { "CP-132 series", 2, }, - { "CP-114 series", 4, }, -/*10*/ { "CT-114 series", 4, }, - { "CP-102 series", 2, MXSER_HIGHBAUD }, - { "CP-104U series", 4, }, - { "CP-168U series", 8, }, - { "CP-132U series", 2, }, -/*15*/ { "CP-134U series", 4, }, - { "CP-104JU series", 4, }, - { "Moxa UC7000 Serial", 8, }, /* RC7000 */ - { "CP-118U series", 8, }, - { "CP-102UL series", 2, }, -/*20*/ { "CP-102U series", 2, }, - { "CP-118EL series", 8, }, - { "CP-168EL series", 8, }, - { "CP-104EL series", 4, }, - { "CB-108 series", 8, }, -/*25*/ { "CB-114 series", 4, }, - { "CB-134I series", 4, }, - { "CP-138U series", 8, }, - { "POS-104UL series", 4, } -}; - -/* driver_data correspond to the lines in the structure above - see also ISA probe function before you change something */ -static struct pci_device_id mxser_pcibrds[] = { - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 }, - { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 }, - { } -}; -MODULE_DEVICE_TABLE(pci, mxser_pcibrds); - -static int ioaddr[MXSER_BOARDS] = { 0, 0, 0, 0 }; -static int ttymajor = MXSERMAJOR; - -/* Variables for insmod */ - -MODULE_AUTHOR("Casper Yang"); -MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver"); -module_param_array(ioaddr, int, NULL, 0); -module_param(ttymajor, int, 0); -MODULE_LICENSE("GPL"); - -struct mxser_log { - int tick; - unsigned long rxcnt[MXSER_PORTS]; - unsigned long txcnt[MXSER_PORTS]; -}; - - -struct mxser_mon { - unsigned long rxcnt; - unsigned long txcnt; - unsigned long up_rxcnt; - unsigned long up_txcnt; - int modem_status; - unsigned char hold_reason; -}; - -struct mxser_mon_ext { - unsigned long rx_cnt[32]; - unsigned long tx_cnt[32]; - unsigned long up_rxcnt[32]; - unsigned long up_txcnt[32]; - int modem_status[32]; - - long baudrate[32]; - int databits[32]; - int stopbits[32]; - int parity[32]; - int flowctrl[32]; - int fifo[32]; - int iftype[32]; -}; - -struct mxser_board; - -struct mxser_port { - struct mxser_board *board; - struct tty_struct *tty; - - unsigned long ioaddr; - unsigned long opmode_ioaddr; - int max_baud; - - int rx_high_water; - int rx_trigger; /* Rx fifo trigger level */ - int rx_low_water; - int baud_base; /* max. speed */ - int type; /* UART type */ - int flags; /* defined in tty.h */ - - int x_char; /* xon/xoff character */ - int IER; /* Interrupt Enable Register */ - int MCR; /* Modem control register */ - - unsigned char stop_rx; - unsigned char ldisc_stop_rx; - - int custom_divisor; - int close_delay; - unsigned short closing_wait; - unsigned char err_shadow; - unsigned long event; - - int count; /* # of fd on device */ - int blocked_open; /* # of blocked opens */ - struct async_icount icount; /* kernel counters for 4 input interrupts */ - int timeout; - - int read_status_mask; - int ignore_status_mask; - int xmit_fifo_size; - unsigned char *xmit_buf; - int xmit_head; - int xmit_tail; - int xmit_cnt; - - struct ktermios normal_termios; - - struct mxser_mon mon_data; - - spinlock_t slock; - wait_queue_head_t open_wait; - wait_queue_head_t delta_msr_wait; -}; - -struct mxser_board { - unsigned int idx; - int irq; - const struct mxser_cardinfo *info; - unsigned long vector; - unsigned long vector_mask; - - int chip_flag; - int uart_type; - - struct mxser_port ports[MXSER_PORTS_PER_BOARD]; -}; - -struct mxser_mstatus { - tcflag_t cflag; - int cts; - int dsr; - int ri; - int dcd; -}; - -static struct mxser_mstatus GMStatus[MXSER_PORTS]; - -static int mxserBoardCAP[MXSER_BOARDS] = { - 0, 0, 0, 0 - /* 0x180, 0x280, 0x200, 0x320 */ -}; - -static struct mxser_board mxser_boards[MXSER_BOARDS]; -static struct tty_driver *mxvar_sdriver; -static struct mxser_log mxvar_log; -static int mxvar_diagflag; -static unsigned char mxser_msr[MXSER_PORTS + 1]; -static struct mxser_mon_ext mon_data_ext; -static int mxser_set_baud_method[MXSER_PORTS + 1]; - -#ifdef CONFIG_PCI -static int __devinit CheckIsMoxaMust(unsigned long io) -{ - u8 oldmcr, hwid; - int i; - - outb(0, io + UART_LCR); - DISABLE_MOXA_MUST_ENCHANCE_MODE(io); - oldmcr = inb(io + UART_MCR); - outb(0, io + UART_MCR); - SET_MOXA_MUST_XON1_VALUE(io, 0x11); - if ((hwid = inb(io + UART_MCR)) != 0) { - outb(oldmcr, io + UART_MCR); - return MOXA_OTHER_UART; - } - - GET_MOXA_MUST_HARDWARE_ID(io, &hwid); - for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */ - if (hwid == Gpci_uart_info[i].type) - return (int)hwid; - } - return MOXA_OTHER_UART; -} -#endif - -static void process_txrx_fifo(struct mxser_port *info) -{ - int i; - - if ((info->type == PORT_16450) || (info->type == PORT_8250)) { - info->rx_trigger = 1; - info->rx_high_water = 1; - info->rx_low_water = 1; - info->xmit_fifo_size = 1; - } else - for (i = 0; i < UART_INFO_NUM; i++) - if (info->board->chip_flag == Gpci_uart_info[i].type) { - info->rx_trigger = Gpci_uart_info[i].rx_trigger; - info->rx_low_water = Gpci_uart_info[i].rx_low_water; - info->rx_high_water = Gpci_uart_info[i].rx_high_water; - info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size; - break; - } -} - -static unsigned char mxser_get_msr(int baseaddr, int mode, int port) -{ - unsigned char status = 0; - - status = inb(baseaddr + UART_MSR); - - mxser_msr[port] &= 0x0F; - mxser_msr[port] |= status; - status = mxser_msr[port]; - if (mode) - mxser_msr[port] = 0; - - return status; -} - -static int mxser_block_til_ready(struct tty_struct *tty, struct file *filp, - struct mxser_port *port) -{ - DECLARE_WAITQUEUE(wait, current); - int retval; - int do_clocal = 0; - unsigned long flags; - - /* - * If non-blocking mode is set, or the port is not enabled, - * then make the check up front and then exit. - */ - if ((filp->f_flags & O_NONBLOCK) || - test_bit(TTY_IO_ERROR, &tty->flags)) { - port->flags |= ASYNC_NORMAL_ACTIVE; - return 0; - } - - if (tty->termios->c_cflag & CLOCAL) - do_clocal = 1; - - /* - * Block waiting for the carrier detect and the line to become - * free (i.e., not in use by the callout). While we are in - * this loop, port->count is dropped by one, so that - * mxser_close() knows when to free things. We restore it upon - * exit, either normal or abnormal. - */ - retval = 0; - add_wait_queue(&port->open_wait, &wait); - - spin_lock_irqsave(&port->slock, flags); - if (!tty_hung_up_p(filp)) - port->count--; - spin_unlock_irqrestore(&port->slock, flags); - port->blocked_open++; - while (1) { - spin_lock_irqsave(&port->slock, flags); - outb(inb(port->ioaddr + UART_MCR) | - UART_MCR_DTR | UART_MCR_RTS, port->ioaddr + UART_MCR); - spin_unlock_irqrestore(&port->slock, flags); - set_current_state(TASK_INTERRUPTIBLE); - if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) { - if (port->flags & ASYNC_HUP_NOTIFY) - retval = -EAGAIN; - else - retval = -ERESTARTSYS; - break; - } - if (!(port->flags & ASYNC_CLOSING) && - (do_clocal || - (inb(port->ioaddr + UART_MSR) & UART_MSR_DCD))) - break; - if (signal_pending(current)) { - retval = -ERESTARTSYS; - break; - } - schedule(); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&port->open_wait, &wait); - if (!tty_hung_up_p(filp)) - port->count++; - port->blocked_open--; - if (retval) - return retval; - port->flags |= ASYNC_NORMAL_ACTIVE; - return 0; -} - -static int mxser_set_baud(struct mxser_port *info, long newspd) -{ - int quot = 0, baud; - unsigned char cval; - - if (!info->tty || !info->tty->termios) - return -1; - - if (!(info->ioaddr)) - return -1; - - if (newspd > info->max_baud) - return -1; - - if (newspd == 134) { - quot = 2 * info->baud_base / 269; - tty_encode_baud_rate(info->tty, 134, 134); - } else if (newspd) { - quot = info->baud_base / newspd; - if (quot == 0) - quot = 1; - baud = info->baud_base/quot; - tty_encode_baud_rate(info->tty, baud, baud); - } else { - quot = 0; - } - - info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base); - info->timeout += HZ / 50; /* Add .02 seconds of slop */ - - if (quot) { - info->MCR |= UART_MCR_DTR; - outb(info->MCR, info->ioaddr + UART_MCR); - } else { - info->MCR &= ~UART_MCR_DTR; - outb(info->MCR, info->ioaddr + UART_MCR); - return 0; - } - - cval = inb(info->ioaddr + UART_LCR); - - outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */ - - outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */ - outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */ - outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */ - -#ifdef BOTHER - if (C_BAUD(info->tty) == BOTHER) { - quot = info->baud_base % newspd; - quot *= 8; - if (quot % newspd > newspd / 2) { - quot /= newspd; - quot++; - } else - quot /= newspd; - - SET_MOXA_MUST_ENUM_VALUE(info->ioaddr, quot); - } else -#endif - SET_MOXA_MUST_ENUM_VALUE(info->ioaddr, 0); - - return 0; -} - -/* - * This routine is called to set the UART divisor registers to match - * the specified baud rate for a serial port. - */ -static int mxser_change_speed(struct mxser_port *info, - struct ktermios *old_termios) -{ - unsigned cflag, cval, fcr; - int ret = 0; - unsigned char status; - - if (!info->tty || !info->tty->termios) - return ret; - cflag = info->tty->termios->c_cflag; - if (!(info->ioaddr)) - return ret; - - if (mxser_set_baud_method[info->tty->index] == 0) - mxser_set_baud(info, tty_get_baud_rate(info->tty)); - - /* byte size and parity */ - switch (cflag & CSIZE) { - case CS5: - cval = 0x00; - break; - case CS6: - cval = 0x01; - break; - case CS7: - cval = 0x02; - break; - case CS8: - cval = 0x03; - break; - default: - cval = 0x00; - break; /* too keep GCC shut... */ - } - if (cflag & CSTOPB) - cval |= 0x04; - if (cflag & PARENB) - cval |= UART_LCR_PARITY; - if (!(cflag & PARODD)) - cval |= UART_LCR_EPAR; - if (cflag & CMSPAR) - cval |= UART_LCR_SPAR; - - if ((info->type == PORT_8250) || (info->type == PORT_16450)) { - if (info->board->chip_flag) { - fcr = UART_FCR_ENABLE_FIFO; - fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; - SET_MOXA_MUST_FIFO_VALUE(info); - } else - fcr = 0; - } else { - fcr = UART_FCR_ENABLE_FIFO; - if (info->board->chip_flag) { - fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; - SET_MOXA_MUST_FIFO_VALUE(info); - } else { - switch (info->rx_trigger) { - case 1: - fcr |= UART_FCR_TRIGGER_1; - break; - case 4: - fcr |= UART_FCR_TRIGGER_4; - break; - case 8: - fcr |= UART_FCR_TRIGGER_8; - break; - default: - fcr |= UART_FCR_TRIGGER_14; - break; - } - } - } - - /* CTS flow control flag and modem status interrupts */ - info->IER &= ~UART_IER_MSI; - info->MCR &= ~UART_MCR_AFE; - if (cflag & CRTSCTS) { - info->flags |= ASYNC_CTS_FLOW; - info->IER |= UART_IER_MSI; - if ((info->type == PORT_16550A) || (info->board->chip_flag)) { - info->MCR |= UART_MCR_AFE; - } else { - status = inb(info->ioaddr + UART_MSR); - if (info->tty->hw_stopped) { - if (status & UART_MSR_CTS) { - info->tty->hw_stopped = 0; - if (info->type != PORT_16550A && - !info->board->chip_flag) { - outb(info->IER & ~UART_IER_THRI, - info->ioaddr + - UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + - UART_IER); - } - tty_wakeup(info->tty); - } - } else { - if (!(status & UART_MSR_CTS)) { - info->tty->hw_stopped = 1; - if ((info->type != PORT_16550A) && - (!info->board->chip_flag)) { - info->IER &= ~UART_IER_THRI; - outb(info->IER, info->ioaddr + - UART_IER); - } - } - } - } - } else { - info->flags &= ~ASYNC_CTS_FLOW; - } - outb(info->MCR, info->ioaddr + UART_MCR); - if (cflag & CLOCAL) { - info->flags &= ~ASYNC_CHECK_CD; - } else { - info->flags |= ASYNC_CHECK_CD; - info->IER |= UART_IER_MSI; - } - outb(info->IER, info->ioaddr + UART_IER); - - /* - * Set up parity check flag - */ - info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; - if (I_INPCK(info->tty)) - info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (I_BRKINT(info->tty) || I_PARMRK(info->tty)) - info->read_status_mask |= UART_LSR_BI; - - info->ignore_status_mask = 0; - - if (I_IGNBRK(info->tty)) { - info->ignore_status_mask |= UART_LSR_BI; - info->read_status_mask |= UART_LSR_BI; - /* - * If we're ignore parity and break indicators, ignore - * overruns too. (For real raw support). - */ - if (I_IGNPAR(info->tty)) { - info->ignore_status_mask |= - UART_LSR_OE | - UART_LSR_PE | - UART_LSR_FE; - info->read_status_mask |= - UART_LSR_OE | - UART_LSR_PE | - UART_LSR_FE; - } - } - if (info->board->chip_flag) { - SET_MOXA_MUST_XON1_VALUE(info->ioaddr, START_CHAR(info->tty)); - SET_MOXA_MUST_XOFF1_VALUE(info->ioaddr, STOP_CHAR(info->tty)); - if (I_IXON(info->tty)) { - ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr); - } else { - DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr); - } - if (I_IXOFF(info->tty)) { - ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr); - } else { - DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr); - } - } - - - outb(fcr, info->ioaddr + UART_FCR); /* set fcr */ - outb(cval, info->ioaddr + UART_LCR); - - return ret; -} - -static void mxser_check_modem_status(struct mxser_port *port, int status) -{ - /* update input line counters */ - if (status & UART_MSR_TERI) - port->icount.rng++; - if (status & UART_MSR_DDSR) - port->icount.dsr++; - if (status & UART_MSR_DDCD) - port->icount.dcd++; - if (status & UART_MSR_DCTS) - port->icount.cts++; - port->mon_data.modem_status = status; - wake_up_interruptible(&port->delta_msr_wait); - - if ((port->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) { - if (status & UART_MSR_DCD) - wake_up_interruptible(&port->open_wait); - } - - if (port->flags & ASYNC_CTS_FLOW) { - if (port->tty->hw_stopped) { - if (status & UART_MSR_CTS) { - port->tty->hw_stopped = 0; - - if ((port->type != PORT_16550A) && - (!port->board->chip_flag)) { - outb(port->IER & ~UART_IER_THRI, - port->ioaddr + UART_IER); - port->IER |= UART_IER_THRI; - outb(port->IER, port->ioaddr + - UART_IER); - } - tty_wakeup(port->tty); - } - } else { - if (!(status & UART_MSR_CTS)) { - port->tty->hw_stopped = 1; - if (port->type != PORT_16550A && - !port->board->chip_flag) { - port->IER &= ~UART_IER_THRI; - outb(port->IER, port->ioaddr + - UART_IER); - } - } - } - } -} - -static int mxser_startup(struct mxser_port *info) -{ - unsigned long page; - unsigned long flags; - - page = __get_free_page(GFP_KERNEL); - if (!page) - return -ENOMEM; - - spin_lock_irqsave(&info->slock, flags); - - if (info->flags & ASYNC_INITIALIZED) { - free_page(page); - spin_unlock_irqrestore(&info->slock, flags); - return 0; - } - - if (!info->ioaddr || !info->type) { - if (info->tty) - set_bit(TTY_IO_ERROR, &info->tty->flags); - free_page(page); - spin_unlock_irqrestore(&info->slock, flags); - return 0; - } - if (info->xmit_buf) - free_page(page); - else - info->xmit_buf = (unsigned char *) page; - - /* - * Clear the FIFO buffers and disable them - * (they will be reenabled in mxser_change_speed()) - */ - if (info->board->chip_flag) - outb((UART_FCR_CLEAR_RCVR | - UART_FCR_CLEAR_XMIT | - MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR); - else - outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), - info->ioaddr + UART_FCR); - - /* - * At this point there's no way the LSR could still be 0xFF; - * if it is, then bail out, because there's likely no UART - * here. - */ - if (inb(info->ioaddr + UART_LSR) == 0xff) { - spin_unlock_irqrestore(&info->slock, flags); - if (capable(CAP_SYS_ADMIN)) { - if (info->tty) - set_bit(TTY_IO_ERROR, &info->tty->flags); - return 0; - } else - return -ENODEV; - } - - /* - * Clear the interrupt registers. - */ - (void) inb(info->ioaddr + UART_LSR); - (void) inb(info->ioaddr + UART_RX); - (void) inb(info->ioaddr + UART_IIR); - (void) inb(info->ioaddr + UART_MSR); - - /* - * Now, initialize the UART - */ - outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */ - info->MCR = UART_MCR_DTR | UART_MCR_RTS; - outb(info->MCR, info->ioaddr + UART_MCR); - - /* - * Finally, enable interrupts - */ - info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; - - if (info->board->chip_flag) - info->IER |= MOXA_MUST_IER_EGDAI; - outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */ - - /* - * And clear the interrupt registers again for luck. - */ - (void) inb(info->ioaddr + UART_LSR); - (void) inb(info->ioaddr + UART_RX); - (void) inb(info->ioaddr + UART_IIR); - (void) inb(info->ioaddr + UART_MSR); - - if (info->tty) - clear_bit(TTY_IO_ERROR, &info->tty->flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - - /* - * and set the speed of the serial port - */ - mxser_change_speed(info, NULL); - info->flags |= ASYNC_INITIALIZED; - spin_unlock_irqrestore(&info->slock, flags); - - return 0; -} - -/* - * This routine will shutdown a serial port; interrupts maybe disabled, and - * DTR is dropped if the hangup on close termio flag is on. - */ -static void mxser_shutdown(struct mxser_port *info) -{ - unsigned long flags; - - if (!(info->flags & ASYNC_INITIALIZED)) - return; - - spin_lock_irqsave(&info->slock, flags); - - /* - * clear delta_msr_wait queue to avoid mem leaks: we may free the irq - * here so the queue might never be waken up - */ - wake_up_interruptible(&info->delta_msr_wait); - - /* - * Free the IRQ, if necessary - */ - if (info->xmit_buf) { - free_page((unsigned long) info->xmit_buf); - info->xmit_buf = NULL; - } - - info->IER = 0; - outb(0x00, info->ioaddr + UART_IER); - - if (!info->tty || (info->tty->termios->c_cflag & HUPCL)) - info->MCR &= ~(UART_MCR_DTR | UART_MCR_RTS); - outb(info->MCR, info->ioaddr + UART_MCR); - - /* clear Rx/Tx FIFO's */ - if (info->board->chip_flag) - outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT | - MOXA_MUST_FCR_GDA_MODE_ENABLE, - info->ioaddr + UART_FCR); - else - outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT, - info->ioaddr + UART_FCR); - - /* read data port to reset things */ - (void) inb(info->ioaddr + UART_RX); - - if (info->tty) - set_bit(TTY_IO_ERROR, &info->tty->flags); - - info->flags &= ~ASYNC_INITIALIZED; - - if (info->board->chip_flag) - SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr); - - spin_unlock_irqrestore(&info->slock, flags); -} - -/* - * This routine is called whenever a serial port is opened. It - * enables interrupts for a serial port, linking in its async structure into - * the IRQ chain. It also performs the serial-specific - * initialization for the tty structure. - */ -static int mxser_open(struct tty_struct *tty, struct file *filp) -{ - struct mxser_port *info; - unsigned long flags; - int retval, line; - - line = tty->index; - if (line == MXSER_PORTS) - return 0; - if (line < 0 || line > MXSER_PORTS) - return -ENODEV; - info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD]; - if (!info->ioaddr) - return -ENODEV; - - tty->driver_data = info; - info->tty = tty; - /* - * Start up serial port - */ - spin_lock_irqsave(&info->slock, flags); - info->count++; - spin_unlock_irqrestore(&info->slock, flags); - retval = mxser_startup(info); - if (retval) - return retval; - - retval = mxser_block_til_ready(tty, filp, info); - if (retval) - return retval; - - /* unmark here for very high baud rate (ex. 921600 bps) used */ - tty->low_latency = 1; - return 0; -} - -/* - * This routine is called when the serial port gets closed. First, we - * wait for the last remaining data to be sent. Then, we unlink its - * async structure from the interrupt chain if necessary, and we free - * that IRQ if nothing is left in the chain. - */ -static void mxser_close(struct tty_struct *tty, struct file *filp) -{ - struct mxser_port *info = tty->driver_data; - - unsigned long timeout; - unsigned long flags; - - if (tty->index == MXSER_PORTS) - return; - if (!info) - return; - - spin_lock_irqsave(&info->slock, flags); - - if (tty_hung_up_p(filp)) { - spin_unlock_irqrestore(&info->slock, flags); - return; - } - if ((tty->count == 1) && (info->count != 1)) { - /* - * Uh, oh. tty->count is 1, which means that the tty - * structure will be freed. Info->count should always - * be one in these conditions. If it's greater than - * one, we've got real problems, since it means the - * serial port won't be shutdown. - */ - printk(KERN_ERR "mxser_close: bad serial port count; " - "tty->count is 1, info->count is %d\n", info->count); - info->count = 1; - } - if (--info->count < 0) { - printk(KERN_ERR "mxser_close: bad serial port count for " - "ttys%d: %d\n", tty->index, info->count); - info->count = 0; - } - if (info->count) { - spin_unlock_irqrestore(&info->slock, flags); - return; - } - info->flags |= ASYNC_CLOSING; - spin_unlock_irqrestore(&info->slock, flags); - /* - * Save the termios structure, since this port may have - * separate termios for callout and dialin. - */ - if (info->flags & ASYNC_NORMAL_ACTIVE) - info->normal_termios = *tty->termios; - /* - * Now we wait for the transmit buffer to clear; and we notify - * the line discipline to only process XON/XOFF characters. - */ - tty->closing = 1; - if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) - tty_wait_until_sent(tty, info->closing_wait); - /* - * At this point we stop accepting input. To do this, we - * disable the receive line status interrupts, and tell the - * interrupt driver to stop checking the data ready bit in the - * line status register. - */ - info->IER &= ~UART_IER_RLSI; - if (info->board->chip_flag) - info->IER &= ~MOXA_MUST_RECV_ISR; - - if (info->flags & ASYNC_INITIALIZED) { - outb(info->IER, info->ioaddr + UART_IER); - /* - * Before we drop DTR, make sure the UART transmitter - * has completely drained; this is especially - * important if there is a transmit FIFO! - */ - timeout = jiffies + HZ; - while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) { - schedule_timeout_interruptible(5); - if (time_after(jiffies, timeout)) - break; - } - } - mxser_shutdown(info); - - if (tty->driver->flush_buffer) - tty->driver->flush_buffer(tty); - - tty_ldisc_flush(tty); - - tty->closing = 0; - info->event = 0; - info->tty = NULL; - if (info->blocked_open) { - if (info->close_delay) - schedule_timeout_interruptible(info->close_delay); - wake_up_interruptible(&info->open_wait); - } - - info->flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING); -} - -static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count) -{ - int c, total = 0; - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - if (!info->xmit_buf) - return 0; - - while (1) { - c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, - SERIAL_XMIT_SIZE - info->xmit_head)); - if (c <= 0) - break; - - memcpy(info->xmit_buf + info->xmit_head, buf, c); - spin_lock_irqsave(&info->slock, flags); - info->xmit_head = (info->xmit_head + c) & - (SERIAL_XMIT_SIZE - 1); - info->xmit_cnt += c; - spin_unlock_irqrestore(&info->slock, flags); - - buf += c; - count -= c; - total += c; - } - - if (info->xmit_cnt && !tty->stopped) { - if (!tty->hw_stopped || - (info->type == PORT_16550A) || - (info->board->chip_flag)) { - spin_lock_irqsave(&info->slock, flags); - outb(info->IER & ~UART_IER_THRI, info->ioaddr + - UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - spin_unlock_irqrestore(&info->slock, flags); - } - } - return total; -} - -static void mxser_put_char(struct tty_struct *tty, unsigned char ch) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - if (!info->xmit_buf) - return; - - if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1) - return; - - spin_lock_irqsave(&info->slock, flags); - info->xmit_buf[info->xmit_head++] = ch; - info->xmit_head &= SERIAL_XMIT_SIZE - 1; - info->xmit_cnt++; - spin_unlock_irqrestore(&info->slock, flags); - if (!tty->stopped) { - if (!tty->hw_stopped || - (info->type == PORT_16550A) || - info->board->chip_flag) { - spin_lock_irqsave(&info->slock, flags); - outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - spin_unlock_irqrestore(&info->slock, flags); - } - } -} - - -static void mxser_flush_chars(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - if (info->xmit_cnt <= 0 || - tty->stopped || - !info->xmit_buf || - (tty->hw_stopped && - (info->type != PORT_16550A) && - (!info->board->chip_flag) - )) - return; - - spin_lock_irqsave(&info->slock, flags); - - outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - - spin_unlock_irqrestore(&info->slock, flags); -} - -static int mxser_write_room(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - int ret; - - ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; - if (ret < 0) - ret = 0; - return ret; -} - -static int mxser_chars_in_buffer(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - return info->xmit_cnt; -} - -static void mxser_flush_buffer(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - char fcr; - unsigned long flags; - - - spin_lock_irqsave(&info->slock, flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - - fcr = inb(info->ioaddr + UART_FCR); - outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), - info->ioaddr + UART_FCR); - outb(fcr, info->ioaddr + UART_FCR); - - spin_unlock_irqrestore(&info->slock, flags); - - tty_wakeup(tty); -} - -/* - * ------------------------------------------------------------ - * friends of mxser_ioctl() - * ------------------------------------------------------------ - */ -static int mxser_get_serial_info(struct mxser_port *info, - struct serial_struct __user *retinfo) -{ - struct serial_struct tmp = { - .type = info->type, - .line = info->tty->index, - .port = info->ioaddr, - .irq = info->board->irq, - .flags = info->flags, - .baud_base = info->baud_base, - .close_delay = info->close_delay, - .closing_wait = info->closing_wait, - .custom_divisor = info->custom_divisor, - .hub6 = 0 - }; - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) - return -EFAULT; - return 0; -} - -static int mxser_set_serial_info(struct mxser_port *info, - struct serial_struct __user *new_info) -{ - struct serial_struct new_serial; - unsigned long sl_flags; - unsigned int flags; - int retval = 0; - - if (!new_info || !info->ioaddr) - return -EFAULT; - if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) - return -EFAULT; - - if ((new_serial.irq != info->board->irq) || - (new_serial.port != info->ioaddr) || - (new_serial.custom_divisor != info->custom_divisor) || - (new_serial.baud_base != info->baud_base)) - return -EPERM; - - flags = info->flags & ASYNC_SPD_MASK; - - if (!capable(CAP_SYS_ADMIN)) { - if ((new_serial.baud_base != info->baud_base) || - (new_serial.close_delay != info->close_delay) || - ((new_serial.flags & ~ASYNC_USR_MASK) != (info->flags & ~ASYNC_USR_MASK))) - return -EPERM; - info->flags = ((info->flags & ~ASYNC_USR_MASK) | - (new_serial.flags & ASYNC_USR_MASK)); - } else { - /* - * OK, past this point, all the error checking has been done. - * At this point, we start making changes..... - */ - info->flags = ((info->flags & ~ASYNC_FLAGS) | - (new_serial.flags & ASYNC_FLAGS)); - info->close_delay = new_serial.close_delay * HZ / 100; - info->closing_wait = new_serial.closing_wait * HZ / 100; - info->tty->low_latency = - (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; - info->tty->low_latency = 0; - } - - info->type = new_serial.type; - - process_txrx_fifo(info); - - if (info->flags & ASYNC_INITIALIZED) { - if (flags != (info->flags & ASYNC_SPD_MASK)) { - spin_lock_irqsave(&info->slock, sl_flags); - mxser_change_speed(info, NULL); - spin_unlock_irqrestore(&info->slock, sl_flags); - } - } else - retval = mxser_startup(info); - - return retval; -} - -/* - * mxser_get_lsr_info - get line status register info - * - * Purpose: Let user call ioctl() to get info when the UART physically - * is emptied. On bus types like RS485, the transmitter must - * release the bus after transmitting. This must be done when - * the transmit shift register is empty, not be done when the - * transmit holding register is empty. This functionality - * allows an RS485 driver to be written in user space. - */ -static int mxser_get_lsr_info(struct mxser_port *info, - unsigned int __user *value) -{ - unsigned char status; - unsigned int result; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - status = inb(info->ioaddr + UART_LSR); - spin_unlock_irqrestore(&info->slock, flags); - result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); - return put_user(result, value); -} - -/* - * This routine sends a break character out the serial port. - */ -static void mxser_send_break(struct mxser_port *info, int duration) -{ - unsigned long flags; - - if (!info->ioaddr) - return; - set_current_state(TASK_INTERRUPTIBLE); - spin_lock_irqsave(&info->slock, flags); - outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC, - info->ioaddr + UART_LCR); - spin_unlock_irqrestore(&info->slock, flags); - schedule_timeout(duration); - spin_lock_irqsave(&info->slock, flags); - outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC, - info->ioaddr + UART_LCR); - spin_unlock_irqrestore(&info->slock, flags); -} - -static int mxser_tiocmget(struct tty_struct *tty, struct file *file) -{ - struct mxser_port *info = tty->driver_data; - unsigned char control, status; - unsigned long flags; - - - if (tty->index == MXSER_PORTS) - return -ENOIOCTLCMD; - if (test_bit(TTY_IO_ERROR, &tty->flags)) - return -EIO; - - control = info->MCR; - - spin_lock_irqsave(&info->slock, flags); - status = inb(info->ioaddr + UART_MSR); - if (status & UART_MSR_ANY_DELTA) - mxser_check_modem_status(info, status); - spin_unlock_irqrestore(&info->slock, flags); - return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) | - ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) | - ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) | - ((status & UART_MSR_RI) ? TIOCM_RNG : 0) | - ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) | - ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); -} - -static int mxser_tiocmset(struct tty_struct *tty, struct file *file, - unsigned int set, unsigned int clear) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - - if (tty->index == MXSER_PORTS) - return -ENOIOCTLCMD; - if (test_bit(TTY_IO_ERROR, &tty->flags)) - return -EIO; - - spin_lock_irqsave(&info->slock, flags); - - if (set & TIOCM_RTS) - info->MCR |= UART_MCR_RTS; - if (set & TIOCM_DTR) - info->MCR |= UART_MCR_DTR; - - if (clear & TIOCM_RTS) - info->MCR &= ~UART_MCR_RTS; - if (clear & TIOCM_DTR) - info->MCR &= ~UART_MCR_DTR; - - outb(info->MCR, info->ioaddr + UART_MCR); - spin_unlock_irqrestore(&info->slock, flags); - return 0; -} - -static int __init mxser_program_mode(int port) -{ - int id, i, j, n; - - outb(0, port); - outb(0, port); - outb(0, port); - (void)inb(port); - (void)inb(port); - outb(0, port); - (void)inb(port); - - id = inb(port + 1) & 0x1F; - if ((id != C168_ASIC_ID) && - (id != C104_ASIC_ID) && - (id != C102_ASIC_ID) && - (id != CI132_ASIC_ID) && - (id != CI134_ASIC_ID) && - (id != CI104J_ASIC_ID)) - return -1; - for (i = 0, j = 0; i < 4; i++) { - n = inb(port + 2); - if (n == 'M') { - j = 1; - } else if ((j == 1) && (n == 1)) { - j = 2; - break; - } else - j = 0; - } - if (j != 2) - id = -2; - return id; -} - -static void __init mxser_normal_mode(int port) -{ - int i, n; - - outb(0xA5, port + 1); - outb(0x80, port + 3); - outb(12, port + 0); /* 9600 bps */ - outb(0, port + 1); - outb(0x03, port + 3); /* 8 data bits */ - outb(0x13, port + 4); /* loop back mode */ - for (i = 0; i < 16; i++) { - n = inb(port + 5); - if ((n & 0x61) == 0x60) - break; - if ((n & 1) == 1) - (void)inb(port); - } - outb(0x00, port + 4); -} - -#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */ -#define CHIP_DO 0x02 /* Serial Data Output in Eprom */ -#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */ -#define CHIP_DI 0x08 /* Serial Data Input in Eprom */ -#define EN_CCMD 0x000 /* Chip's command register */ -#define EN0_RSARLO 0x008 /* Remote start address reg 0 */ -#define EN0_RSARHI 0x009 /* Remote start address reg 1 */ -#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */ -#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */ -#define EN0_DCFG 0x00E /* Data configuration reg WR */ -#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */ -#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */ -#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */ -static int __init mxser_read_register(int port, unsigned short *regs) -{ - int i, k, value, id; - unsigned int j; - - id = mxser_program_mode(port); - if (id < 0) - return id; - for (i = 0; i < 14; i++) { - k = (i & 0x3F) | 0x180; - for (j = 0x100; j > 0; j >>= 1) { - outb(CHIP_CS, port); - if (k & j) { - outb(CHIP_CS | CHIP_DO, port); - outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */ - } else { - outb(CHIP_CS, port); - outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */ - } - } - (void)inb(port); - value = 0; - for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) { - outb(CHIP_CS, port); - outb(CHIP_CS | CHIP_SK, port); - if (inb(port) & CHIP_DI) - value |= j; - } - regs[i] = value; - outb(0, port); - } - mxser_normal_mode(port); - return id; -} - -static int mxser_ioctl_special(unsigned int cmd, void __user *argp) -{ - struct mxser_port *port; - int result, status; - unsigned int i, j; - - switch (cmd) { - case MOXA_GET_MAJOR: - return put_user(ttymajor, (int __user *)argp); - - case MOXA_CHKPORTENABLE: - result = 0; - - for (i = 0; i < MXSER_BOARDS; i++) - for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) - if (mxser_boards[i].ports[j].ioaddr) - result |= (1 << i); - - return put_user(result, (unsigned long __user *)argp); - case MOXA_GETDATACOUNT: - if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log))) - return -EFAULT; - return 0; - case MOXA_GETMSTATUS: - for (i = 0; i < MXSER_BOARDS; i++) - for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) { - port = &mxser_boards[i].ports[j]; - - GMStatus[i].ri = 0; - if (!port->ioaddr) { - GMStatus[i].dcd = 0; - GMStatus[i].dsr = 0; - GMStatus[i].cts = 0; - continue; - } - - if (!port->tty || !port->tty->termios) - GMStatus[i].cflag = - port->normal_termios.c_cflag; - else - GMStatus[i].cflag = - port->tty->termios->c_cflag; - - status = inb(port->ioaddr + UART_MSR); - if (status & 0x80 /*UART_MSR_DCD */ ) - GMStatus[i].dcd = 1; - else - GMStatus[i].dcd = 0; - - if (status & 0x20 /*UART_MSR_DSR */ ) - GMStatus[i].dsr = 1; - else - GMStatus[i].dsr = 0; - - - if (status & 0x10 /*UART_MSR_CTS */ ) - GMStatus[i].cts = 1; - else - GMStatus[i].cts = 0; - } - if (copy_to_user(argp, GMStatus, - sizeof(struct mxser_mstatus) * MXSER_PORTS)) - return -EFAULT; - return 0; - case MOXA_ASPP_MON_EXT: { - int p, shiftbit; - unsigned long opmode; - unsigned cflag, iflag; - - for (i = 0; i < MXSER_BOARDS; i++) - for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) { - port = &mxser_boards[i].ports[j]; - if (!port->ioaddr) - continue; - - status = mxser_get_msr(port->ioaddr, 0, i); - - if (status & UART_MSR_TERI) - port->icount.rng++; - if (status & UART_MSR_DDSR) - port->icount.dsr++; - if (status & UART_MSR_DDCD) - port->icount.dcd++; - if (status & UART_MSR_DCTS) - port->icount.cts++; - - port->mon_data.modem_status = status; - mon_data_ext.rx_cnt[i] = port->mon_data.rxcnt; - mon_data_ext.tx_cnt[i] = port->mon_data.txcnt; - mon_data_ext.up_rxcnt[i] = - port->mon_data.up_rxcnt; - mon_data_ext.up_txcnt[i] = - port->mon_data.up_txcnt; - mon_data_ext.modem_status[i] = - port->mon_data.modem_status; - mon_data_ext.baudrate[i] = - tty_get_baud_rate(port->tty); - - if (!port->tty || !port->tty->termios) { - cflag = port->normal_termios.c_cflag; - iflag = port->normal_termios.c_iflag; - } else { - cflag = port->tty->termios->c_cflag; - iflag = port->tty->termios->c_iflag; - } - - mon_data_ext.databits[i] = cflag & CSIZE; - - mon_data_ext.stopbits[i] = cflag & CSTOPB; - - mon_data_ext.parity[i] = - cflag & (PARENB | PARODD | CMSPAR); - - mon_data_ext.flowctrl[i] = 0x00; - - if (cflag & CRTSCTS) - mon_data_ext.flowctrl[i] |= 0x03; - - if (iflag & (IXON | IXOFF)) - mon_data_ext.flowctrl[i] |= 0x0C; - - if (port->type == PORT_16550A) - mon_data_ext.fifo[i] = 1; - else - mon_data_ext.fifo[i] = 0; - - p = i % 4; - shiftbit = p * 2; - opmode = inb(port->opmode_ioaddr) >> shiftbit; - opmode &= OP_MODE_MASK; - - mon_data_ext.iftype[i] = opmode; - - } - if (copy_to_user(argp, &mon_data_ext, - sizeof(mon_data_ext))) - return -EFAULT; - - return 0; - - } default: - return -ENOIOCTLCMD; - } - return 0; -} - -static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg, - struct async_icount *cprev) -{ - struct async_icount cnow; - unsigned long flags; - int ret; - - spin_lock_irqsave(&info->slock, flags); - cnow = info->icount; /* atomic copy */ - spin_unlock_irqrestore(&info->slock, flags); - - ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts)); - - *cprev = cnow; - - return ret; -} - -static int mxser_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - struct mxser_port *info = tty->driver_data; - struct async_icount cnow; - struct serial_icounter_struct __user *p_cuser; - unsigned long flags; - void __user *argp = (void __user *)arg; - int retval; - - if (tty->index == MXSER_PORTS) - return mxser_ioctl_special(cmd, argp); - - if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) { - int p; - unsigned long opmode; - static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f }; - int shiftbit; - unsigned char val, mask; - - p = tty->index % 4; - if (cmd == MOXA_SET_OP_MODE) { - if (get_user(opmode, (int __user *) argp)) - return -EFAULT; - if (opmode != RS232_MODE && - opmode != RS485_2WIRE_MODE && - opmode != RS422_MODE && - opmode != RS485_4WIRE_MODE) - return -EFAULT; - mask = ModeMask[p]; - shiftbit = p * 2; - val = inb(info->opmode_ioaddr); - val &= mask; - val |= (opmode << shiftbit); - outb(val, info->opmode_ioaddr); - } else { - shiftbit = p * 2; - opmode = inb(info->opmode_ioaddr) >> shiftbit; - opmode &= OP_MODE_MASK; - if (put_user(opmode, (int __user *)argp)) - return -EFAULT; - } - return 0; - } - - if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && cmd != TIOCGICOUNT && - test_bit(TTY_IO_ERROR, &tty->flags)) - return -EIO; - - switch (cmd) { - case TCSBRK: /* SVID version: non-zero arg --> no break */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - if (!arg) - mxser_send_break(info, HZ / 4); /* 1/4 second */ - return 0; - case TCSBRKP: /* support for POSIX tcsendbreak() */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - mxser_send_break(info, arg ? arg * (HZ / 10) : HZ / 4); - return 0; - case TIOCGSOFTCAR: - return put_user(!!C_CLOCAL(tty), (unsigned long __user *)argp); - case TIOCSSOFTCAR: - if (get_user(arg, (unsigned long __user *)argp)) - return -EFAULT; - tty->termios->c_cflag = ((tty->termios->c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0)); - return 0; - case TIOCGSERIAL: - return mxser_get_serial_info(info, argp); - case TIOCSSERIAL: - return mxser_set_serial_info(info, argp); - case TIOCSERGETLSR: /* Get line status register */ - return mxser_get_lsr_info(info, argp); - /* - * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change - * - mask passed in arg for lines of interest - * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) - * Caller should use TIOCGICOUNT to see which one it was - */ - case TIOCMIWAIT: - spin_lock_irqsave(&info->slock, flags); - cnow = info->icount; /* note the counters on entry */ - spin_unlock_irqrestore(&info->slock, flags); - - return wait_event_interruptible(info->delta_msr_wait, - mxser_cflags_changed(info, arg, &cnow)); - /* - * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) - * Return: write counters to the user passed counter struct - * NB: both 1->0 and 0->1 transitions are counted except for - * RI where only 0->1 is counted. - */ - case TIOCGICOUNT: - spin_lock_irqsave(&info->slock, flags); - cnow = info->icount; - spin_unlock_irqrestore(&info->slock, flags); - p_cuser = argp; - if (put_user(cnow.frame, &p_cuser->frame)) - return -EFAULT; - if (put_user(cnow.brk, &p_cuser->brk)) - return -EFAULT; - if (put_user(cnow.overrun, &p_cuser->overrun)) - return -EFAULT; - if (put_user(cnow.buf_overrun, &p_cuser->buf_overrun)) - return -EFAULT; - if (put_user(cnow.parity, &p_cuser->parity)) - return -EFAULT; - if (put_user(cnow.rx, &p_cuser->rx)) - return -EFAULT; - if (put_user(cnow.tx, &p_cuser->tx)) - return -EFAULT; - put_user(cnow.cts, &p_cuser->cts); - put_user(cnow.dsr, &p_cuser->dsr); - put_user(cnow.rng, &p_cuser->rng); - put_user(cnow.dcd, &p_cuser->dcd); - return 0; - case MOXA_HighSpeedOn: - return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp); - case MOXA_SDS_RSTICOUNTER: - info->mon_data.rxcnt = 0; - info->mon_data.txcnt = 0; - return 0; - - case MOXA_ASPP_OQUEUE:{ - int len, lsr; - - len = mxser_chars_in_buffer(tty); - - lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT; - - len += (lsr ? 0 : 1); - - return put_user(len, (int __user *)argp); - } - case MOXA_ASPP_MON: { - int mcr, status; - - status = mxser_get_msr(info->ioaddr, 1, tty->index); - mxser_check_modem_status(info, status); - - mcr = inb(info->ioaddr + UART_MCR); - if (mcr & MOXA_MUST_MCR_XON_FLAG) - info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD; - else - info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD; - - if (mcr & MOXA_MUST_MCR_TX_XON) - info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT; - else - info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT; - - if (info->tty->hw_stopped) - info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD; - else - info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD; - - if (copy_to_user(argp, &info->mon_data, - sizeof(struct mxser_mon))) - return -EFAULT; - - return 0; - } - case MOXA_ASPP_LSTATUS: { - if (put_user(info->err_shadow, (unsigned char __user *)argp)) - return -EFAULT; - - info->err_shadow = 0; - return 0; - } - case MOXA_SET_BAUD_METHOD: { - int method; - - if (get_user(method, (int __user *)argp)) - return -EFAULT; - mxser_set_baud_method[tty->index] = method; - return put_user(method, (int __user *)argp); - } - default: - return -ENOIOCTLCMD; - } - return 0; -} - -static void mxser_stoprx(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - - info->ldisc_stop_rx = 1; - if (I_IXOFF(tty)) { - if (info->board->chip_flag) { - info->IER &= ~MOXA_MUST_RECV_ISR; - outb(info->IER, info->ioaddr + UART_IER); - } else { - info->x_char = STOP_CHAR(tty); - outb(0, info->ioaddr + UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - } - } - - if (info->tty->termios->c_cflag & CRTSCTS) { - info->MCR &= ~UART_MCR_RTS; - outb(info->MCR, info->ioaddr + UART_MCR); - } -} - -/* - * This routine is called by the upper-layer tty layer to signal that - * incoming characters should be throttled. - */ -static void mxser_throttle(struct tty_struct *tty) -{ - mxser_stoprx(tty); -} - -static void mxser_unthrottle(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - - /* startrx */ - info->ldisc_stop_rx = 0; - if (I_IXOFF(tty)) { - if (info->x_char) - info->x_char = 0; - else { - if (info->board->chip_flag) { - info->IER |= MOXA_MUST_RECV_ISR; - outb(info->IER, info->ioaddr + UART_IER); - } else { - info->x_char = START_CHAR(tty); - outb(0, info->ioaddr + UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - } - } - } - - if (info->tty->termios->c_cflag & CRTSCTS) { - info->MCR |= UART_MCR_RTS; - outb(info->MCR, info->ioaddr + UART_MCR); - } -} - -/* - * mxser_stop() and mxser_start() - * - * This routines are called before setting or resetting tty->stopped. - * They enable or disable transmitter interrupts, as necessary. - */ -static void mxser_stop(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - if (info->IER & UART_IER_THRI) { - info->IER &= ~UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - } - spin_unlock_irqrestore(&info->slock, flags); -} - -static void mxser_start(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - if (info->xmit_cnt && info->xmit_buf) { - outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); - info->IER |= UART_IER_THRI; - outb(info->IER, info->ioaddr + UART_IER); - } - spin_unlock_irqrestore(&info->slock, flags); -} - -static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - mxser_change_speed(info, old_termios); - spin_unlock_irqrestore(&info->slock, flags); - - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { - tty->hw_stopped = 0; - mxser_start(tty); - } - - /* Handle sw stopped */ - if ((old_termios->c_iflag & IXON) && - !(tty->termios->c_iflag & IXON)) { - tty->stopped = 0; - - if (info->board->chip_flag) { - spin_lock_irqsave(&info->slock, flags); - DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr); - spin_unlock_irqrestore(&info->slock, flags); - } - - mxser_start(tty); - } -} - -/* - * mxser_wait_until_sent() --- wait until the transmitter is empty - */ -static void mxser_wait_until_sent(struct tty_struct *tty, int timeout) -{ - struct mxser_port *info = tty->driver_data; - unsigned long orig_jiffies, char_time; - int lsr; - - if (info->type == PORT_UNKNOWN) - return; - - if (info->xmit_fifo_size == 0) - return; /* Just in case.... */ - - orig_jiffies = jiffies; - /* - * Set the check interval to be 1/5 of the estimated time to - * send a single character, and make it at least 1. The check - * interval should also be less than the timeout. - * - * Note: we have to use pretty tight timings here to satisfy - * the NIST-PCTS. - */ - char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size; - char_time = char_time / 5; - if (char_time == 0) - char_time = 1; - if (timeout && timeout < char_time) - char_time = timeout; - /* - * If the transmitter hasn't cleared in twice the approximate - * amount of time to send the entire FIFO, it probably won't - * ever clear. This assumes the UART isn't doing flow - * control, which is currently the case. Hence, if it ever - * takes longer than info->timeout, this is probably due to a - * UART bug of some kind. So, we clamp the timeout parameter at - * 2*info->timeout. - */ - if (!timeout || timeout > 2 * info->timeout) - timeout = 2 * info->timeout; -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk(KERN_DEBUG "In rs_wait_until_sent(%d) check=%lu...", - timeout, char_time); - printk("jiff=%lu...", jiffies); -#endif - while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) { -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk("lsr = %d (jiff=%lu)...", lsr, jiffies); -#endif - schedule_timeout_interruptible(char_time); - if (signal_pending(current)) - break; - if (timeout && time_after(jiffies, orig_jiffies + timeout)) - break; - } - set_current_state(TASK_RUNNING); - -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); -#endif -} - -/* - * This routine is called by tty_hangup() when a hangup is signaled. - */ -static void mxser_hangup(struct tty_struct *tty) -{ - struct mxser_port *info = tty->driver_data; - - mxser_flush_buffer(tty); - mxser_shutdown(info); - info->event = 0; - info->count = 0; - info->flags &= ~ASYNC_NORMAL_ACTIVE; - info->tty = NULL; - wake_up_interruptible(&info->open_wait); -} - -/* - * mxser_rs_break() --- routine which turns the break handling on or off - */ -static void mxser_rs_break(struct tty_struct *tty, int break_state) -{ - struct mxser_port *info = tty->driver_data; - unsigned long flags; - - spin_lock_irqsave(&info->slock, flags); - if (break_state == -1) - outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC, - info->ioaddr + UART_LCR); - else - outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC, - info->ioaddr + UART_LCR); - spin_unlock_irqrestore(&info->slock, flags); -} - -static void mxser_receive_chars(struct mxser_port *port, int *status) -{ - struct tty_struct *tty = port->tty; - unsigned char ch, gdl; - int ignored = 0; - int cnt = 0; - int recv_room; - int max = 256; - - recv_room = tty->receive_room; - if ((recv_room == 0) && (!port->ldisc_stop_rx)) - mxser_stoprx(tty); - - if (port->board->chip_flag != MOXA_OTHER_UART) { - - if (*status & UART_LSR_SPECIAL) - goto intr_old; - if (port->board->chip_flag == MOXA_MUST_MU860_HWID && - (*status & MOXA_MUST_LSR_RERR)) - goto intr_old; - if (*status & MOXA_MUST_LSR_RERR) - goto intr_old; - - gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER); - - if (port->board->chip_flag == MOXA_MUST_MU150_HWID) - gdl &= MOXA_MUST_GDL_MASK; - if (gdl >= recv_room) { - if (!port->ldisc_stop_rx) - mxser_stoprx(tty); - } - while (gdl--) { - ch = inb(port->ioaddr + UART_RX); - tty_insert_flip_char(tty, ch, 0); - cnt++; - } - goto end_intr; - } -intr_old: - - do { - if (max-- < 0) - break; - - ch = inb(port->ioaddr + UART_RX); - if (port->board->chip_flag && (*status & UART_LSR_OE)) - outb(0x23, port->ioaddr + UART_FCR); - *status &= port->read_status_mask; - if (*status & port->ignore_status_mask) { - if (++ignored > 100) - break; - } else { - char flag = 0; - if (*status & UART_LSR_SPECIAL) { - if (*status & UART_LSR_BI) { - flag = TTY_BREAK; - port->icount.brk++; - - if (port->flags & ASYNC_SAK) - do_SAK(tty); - } else if (*status & UART_LSR_PE) { - flag = TTY_PARITY; - port->icount.parity++; - } else if (*status & UART_LSR_FE) { - flag = TTY_FRAME; - port->icount.frame++; - } else if (*status & UART_LSR_OE) { - flag = TTY_OVERRUN; - port->icount.overrun++; - } else - flag = TTY_BREAK; - } - tty_insert_flip_char(tty, ch, flag); - cnt++; - if (cnt >= recv_room) { - if (!port->ldisc_stop_rx) - mxser_stoprx(tty); - break; - } - - } - - if (port->board->chip_flag) - break; - - *status = inb(port->ioaddr + UART_LSR); - } while (*status & UART_LSR_DR); - -end_intr: - mxvar_log.rxcnt[port->tty->index] += cnt; - port->mon_data.rxcnt += cnt; - port->mon_data.up_rxcnt += cnt; - - /* - * We are called from an interrupt context with &port->slock - * being held. Drop it temporarily in order to prevent - * recursive locking. - */ - spin_unlock(&port->slock); - tty_flip_buffer_push(tty); - spin_lock(&port->slock); -} - -static void mxser_transmit_chars(struct mxser_port *port) -{ - int count, cnt; - - if (port->x_char) { - outb(port->x_char, port->ioaddr + UART_TX); - port->x_char = 0; - mxvar_log.txcnt[port->tty->index]++; - port->mon_data.txcnt++; - port->mon_data.up_txcnt++; - port->icount.tx++; - return; - } - - if (port->xmit_buf == NULL) - return; - - if ((port->xmit_cnt <= 0) || port->tty->stopped || - (port->tty->hw_stopped && - (port->type != PORT_16550A) && - (!port->board->chip_flag))) { - port->IER &= ~UART_IER_THRI; - outb(port->IER, port->ioaddr + UART_IER); - return; - } - - cnt = port->xmit_cnt; - count = port->xmit_fifo_size; - do { - outb(port->xmit_buf[port->xmit_tail++], - port->ioaddr + UART_TX); - port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1); - if (--port->xmit_cnt <= 0) - break; - } while (--count > 0); - mxvar_log.txcnt[port->tty->index] += (cnt - port->xmit_cnt); - - port->mon_data.txcnt += (cnt - port->xmit_cnt); - port->mon_data.up_txcnt += (cnt - port->xmit_cnt); - port->icount.tx += (cnt - port->xmit_cnt); - - if (port->xmit_cnt < WAKEUP_CHARS) - tty_wakeup(port->tty); - - if (port->xmit_cnt <= 0) { - port->IER &= ~UART_IER_THRI; - outb(port->IER, port->ioaddr + UART_IER); - } -} - -/* - * This is the serial driver's generic interrupt routine - */ -static irqreturn_t mxser_interrupt(int irq, void *dev_id) -{ - int status, iir, i; - struct mxser_board *brd = NULL; - struct mxser_port *port; - int max, irqbits, bits, msr; - unsigned int int_cnt, pass_counter = 0; - int handled = IRQ_NONE; - - for (i = 0; i < MXSER_BOARDS; i++) - if (dev_id == &mxser_boards[i]) { - brd = dev_id; - break; - } - - if (i == MXSER_BOARDS) - goto irq_stop; - if (brd == NULL) - goto irq_stop; - max = brd->info->nports; - while (pass_counter++ < MXSER_ISR_PASS_LIMIT) { - irqbits = inb(brd->vector) & brd->vector_mask; - if (irqbits == brd->vector_mask) - break; - - handled = IRQ_HANDLED; - for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) { - if (irqbits == brd->vector_mask) - break; - if (bits & irqbits) - continue; - port = &brd->ports[i]; - - int_cnt = 0; - spin_lock(&port->slock); - do { - iir = inb(port->ioaddr + UART_IIR); - if (iir & UART_IIR_NO_INT) - break; - iir &= MOXA_MUST_IIR_MASK; - if (!port->tty || - (port->flags & ASYNC_CLOSING) || - !(port->flags & - ASYNC_INITIALIZED)) { - status = inb(port->ioaddr + UART_LSR); - outb(0x27, port->ioaddr + UART_FCR); - inb(port->ioaddr + UART_MSR); - break; - } - - status = inb(port->ioaddr + UART_LSR); - - if (status & UART_LSR_PE) - port->err_shadow |= NPPI_NOTIFY_PARITY; - if (status & UART_LSR_FE) - port->err_shadow |= NPPI_NOTIFY_FRAMING; - if (status & UART_LSR_OE) - port->err_shadow |= - NPPI_NOTIFY_HW_OVERRUN; - if (status & UART_LSR_BI) - port->err_shadow |= NPPI_NOTIFY_BREAK; - - if (port->board->chip_flag) { - if (iir == MOXA_MUST_IIR_GDA || - iir == MOXA_MUST_IIR_RDA || - iir == MOXA_MUST_IIR_RTO || - iir == MOXA_MUST_IIR_LSR) - mxser_receive_chars(port, - &status); - - } else { - status &= port->read_status_mask; - if (status & UART_LSR_DR) - mxser_receive_chars(port, - &status); - } - msr = inb(port->ioaddr + UART_MSR); - if (msr & UART_MSR_ANY_DELTA) - mxser_check_modem_status(port, msr); - - if (port->board->chip_flag) { - if (iir == 0x02 && (status & - UART_LSR_THRE)) - mxser_transmit_chars(port); - } else { - if (status & UART_LSR_THRE) - mxser_transmit_chars(port); - } - } while (int_cnt++ < MXSER_ISR_PASS_LIMIT); - spin_unlock(&port->slock); - } - } - -irq_stop: - return handled; -} - -static const struct tty_operations mxser_ops = { - .open = mxser_open, - .close = mxser_close, - .write = mxser_write, - .put_char = mxser_put_char, - .flush_chars = mxser_flush_chars, - .write_room = mxser_write_room, - .chars_in_buffer = mxser_chars_in_buffer, - .flush_buffer = mxser_flush_buffer, - .ioctl = mxser_ioctl, - .throttle = mxser_throttle, - .unthrottle = mxser_unthrottle, - .set_termios = mxser_set_termios, - .stop = mxser_stop, - .start = mxser_start, - .hangup = mxser_hangup, - .break_ctl = mxser_rs_break, - .wait_until_sent = mxser_wait_until_sent, - .tiocmget = mxser_tiocmget, - .tiocmset = mxser_tiocmset, -}; - -/* - * The MOXA Smartio/Industio serial driver boot-time initialization code! - */ - -static void mxser_release_res(struct mxser_board *brd, struct pci_dev *pdev, - unsigned int irq) -{ - if (irq) - free_irq(brd->irq, brd); - if (pdev != NULL) { /* PCI */ -#ifdef CONFIG_PCI - pci_release_region(pdev, 2); - pci_release_region(pdev, 3); -#endif - } else { - release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); - release_region(brd->vector, 1); - } -} - -static int __devinit mxser_initbrd(struct mxser_board *brd, - struct pci_dev *pdev) -{ - struct mxser_port *info; - unsigned int i; - int retval; - - printk(KERN_INFO "max. baud rate = %d bps.\n", brd->ports[0].max_baud); - - for (i = 0; i < brd->info->nports; i++) { - info = &brd->ports[i]; - info->board = brd; - info->stop_rx = 0; - info->ldisc_stop_rx = 0; - - /* Enhance mode enabled here */ - if (brd->chip_flag != MOXA_OTHER_UART) - ENABLE_MOXA_MUST_ENCHANCE_MODE(info->ioaddr); - - info->flags = ASYNC_SHARE_IRQ; - info->type = brd->uart_type; - - process_txrx_fifo(info); - - info->custom_divisor = info->baud_base * 16; - info->close_delay = 5 * HZ / 10; - info->closing_wait = 30 * HZ; - info->normal_termios = mxvar_sdriver->init_termios; - init_waitqueue_head(&info->open_wait); - init_waitqueue_head(&info->delta_msr_wait); - memset(&info->mon_data, 0, sizeof(struct mxser_mon)); - info->err_shadow = 0; - spin_lock_init(&info->slock); - - /* before set INT ISR, disable all int */ - outb(inb(info->ioaddr + UART_IER) & 0xf0, - info->ioaddr + UART_IER); - } - - retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser", - brd); - if (retval) { - printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may " - "conflict with another device.\n", - brd->info->name, brd->irq); - /* We hold resources, we need to release them. */ - mxser_release_res(brd, pdev, 0); - } - return retval; -} - -static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd) -{ - int id, i, bits; - unsigned short regs[16], irq; - unsigned char scratch, scratch2; - - brd->chip_flag = MOXA_OTHER_UART; - - id = mxser_read_register(cap, regs); - switch (id) { - case C168_ASIC_ID: - brd->info = &mxser_cards[0]; - break; - case C104_ASIC_ID: - brd->info = &mxser_cards[1]; - break; - case CI104J_ASIC_ID: - brd->info = &mxser_cards[2]; - break; - case C102_ASIC_ID: - brd->info = &mxser_cards[5]; - break; - case CI132_ASIC_ID: - brd->info = &mxser_cards[6]; - break; - case CI134_ASIC_ID: - brd->info = &mxser_cards[7]; - break; - default: - return 0; - } - - irq = 0; - /* some ISA cards have 2 ports, but we want to see them as 4-port (why?) - Flag-hack checks if configuration should be read as 2-port here. */ - if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) { - irq = regs[9] & 0xF000; - irq = irq | (irq >> 4); - if (irq != (regs[9] & 0xFF00)) - return MXSER_ERR_IRQ_CONFLIT; - } else if (brd->info->nports == 4) { - irq = regs[9] & 0xF000; - irq = irq | (irq >> 4); - irq = irq | (irq >> 8); - if (irq != regs[9]) - return MXSER_ERR_IRQ_CONFLIT; - } else if (brd->info->nports == 8) { - irq = regs[9] & 0xF000; - irq = irq | (irq >> 4); - irq = irq | (irq >> 8); - if ((irq != regs[9]) || (irq != regs[10])) - return MXSER_ERR_IRQ_CONFLIT; - } - - if (!irq) - return MXSER_ERR_IRQ; - brd->irq = ((int)(irq & 0xF000) >> 12); - for (i = 0; i < 8; i++) - brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8; - if ((regs[12] & 0x80) == 0) - return MXSER_ERR_VECTOR; - brd->vector = (int)regs[11]; /* interrupt vector */ - if (id == 1) - brd->vector_mask = 0x00FF; - else - brd->vector_mask = 0x000F; - for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) { - if (regs[12] & bits) { - brd->ports[i].baud_base = 921600; - brd->ports[i].max_baud = 921600; - } else { - brd->ports[i].baud_base = 115200; - brd->ports[i].max_baud = 115200; - } - } - scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB); - outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR); - outb(0, cap + UART_EFR); /* EFR is the same as FCR */ - outb(scratch2, cap + UART_LCR); - outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR); - scratch = inb(cap + UART_IIR); - - if (scratch & 0xC0) - brd->uart_type = PORT_16550A; - else - brd->uart_type = PORT_16450; - if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports, - "mxser(IO)")) - return MXSER_ERR_IOADDR; - if (!request_region(brd->vector, 1, "mxser(vector)")) { - release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); - return MXSER_ERR_VECTOR; - } - return brd->info->nports; -} - -static int __devinit mxser_probe(struct pci_dev *pdev, - const struct pci_device_id *ent) -{ -#ifdef CONFIG_PCI - struct mxser_board *brd; - unsigned int i, j; - unsigned long ioaddress; - int retval = -EINVAL; - - for (i = 0; i < MXSER_BOARDS; i++) - if (mxser_boards[i].info == NULL) - break; - - if (i >= MXSER_BOARDS) { - printk(KERN_ERR "Too many Smartio/Industio family boards found " - "(maximum %d), board not configured\n", MXSER_BOARDS); - goto err; - } - - brd = &mxser_boards[i]; - brd->idx = i * MXSER_PORTS_PER_BOARD; - printk(KERN_INFO "Found MOXA %s board (BusNo=%d, DevNo=%d)\n", - mxser_cards[ent->driver_data].name, - pdev->bus->number, PCI_SLOT(pdev->devfn)); - - retval = pci_enable_device(pdev); - if (retval) { - printk(KERN_ERR "Moxa SmartI/O PCI enable fail !\n"); - goto err; - } - - /* io address */ - ioaddress = pci_resource_start(pdev, 2); - retval = pci_request_region(pdev, 2, "mxser(IO)"); - if (retval) - goto err; - - brd->info = &mxser_cards[ent->driver_data]; - for (i = 0; i < brd->info->nports; i++) - brd->ports[i].ioaddr = ioaddress + 8 * i; - - /* vector */ - ioaddress = pci_resource_start(pdev, 3); - retval = pci_request_region(pdev, 3, "mxser(vector)"); - if (retval) - goto err_relio; - brd->vector = ioaddress; - - /* irq */ - brd->irq = pdev->irq; - - brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr); - brd->uart_type = PORT_16550A; - brd->vector_mask = 0; - - for (i = 0; i < brd->info->nports; i++) { - for (j = 0; j < UART_INFO_NUM; j++) { - if (Gpci_uart_info[j].type == brd->chip_flag) { - brd->ports[i].max_baud = - Gpci_uart_info[j].max_baud; - - /* exception....CP-102 */ - if (brd->info->flags & MXSER_HIGHBAUD) - brd->ports[i].max_baud = 921600; - break; - } - } - } - - if (brd->chip_flag == MOXA_MUST_MU860_HWID) { - for (i = 0; i < brd->info->nports; i++) { - if (i < 4) - brd->ports[i].opmode_ioaddr = ioaddress + 4; - else - brd->ports[i].opmode_ioaddr = ioaddress + 0x0c; - } - outb(0, ioaddress + 4); /* default set to RS232 mode */ - outb(0, ioaddress + 0x0c); /* default set to RS232 mode */ - } - - for (i = 0; i < brd->info->nports; i++) { - brd->vector_mask |= (1 << i); - brd->ports[i].baud_base = 921600; - } - - /* mxser_initbrd will hook ISR. */ - retval = mxser_initbrd(brd, pdev); - if (retval) - goto err_null; - - for (i = 0; i < brd->info->nports; i++) - tty_register_device(mxvar_sdriver, brd->idx + i, &pdev->dev); - - pci_set_drvdata(pdev, brd); - - return 0; -err_relio: - pci_release_region(pdev, 2); -err_null: - brd->info = NULL; -err: - return retval; -#else - return -ENODEV; -#endif -} - -static void __devexit mxser_remove(struct pci_dev *pdev) -{ - struct mxser_board *brd = pci_get_drvdata(pdev); - unsigned int i; - - for (i = 0; i < brd->info->nports; i++) - tty_unregister_device(mxvar_sdriver, brd->idx + i); - - mxser_release_res(brd, pdev, 1); - brd->info = NULL; -} - -static struct pci_driver mxser_driver = { - .name = "mxser", - .id_table = mxser_pcibrds, - .probe = mxser_probe, - .remove = __devexit_p(mxser_remove) -}; - -static int __init mxser_module_init(void) -{ - struct mxser_board *brd; - unsigned long cap; - unsigned int i, m, isaloop; - int retval, b; - - pr_debug("Loading module mxser ...\n"); - - mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1); - if (!mxvar_sdriver) - return -ENOMEM; - - printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n", - MXSER_VERSION); - - /* Initialize the tty_driver structure */ - mxvar_sdriver->owner = THIS_MODULE; - mxvar_sdriver->magic = TTY_DRIVER_MAGIC; - mxvar_sdriver->name = "ttyMI"; - mxvar_sdriver->major = ttymajor; - mxvar_sdriver->minor_start = 0; - mxvar_sdriver->num = MXSER_PORTS + 1; - mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL; - mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL; - mxvar_sdriver->init_termios = tty_std_termios; - mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL; - mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV; - tty_set_operations(mxvar_sdriver, &mxser_ops); - - retval = tty_register_driver(mxvar_sdriver); - if (retval) { - printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family " - "tty driver !\n"); - goto err_put; - } - - mxvar_diagflag = 0; - - m = 0; - /* Start finding ISA boards here */ - for (isaloop = 0; isaloop < 2; isaloop++) - for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) { - if (!isaloop) - cap = mxserBoardCAP[b]; /* predefined */ - else - cap = ioaddr[b]; /* module param */ - - if (!cap) - continue; - - brd = &mxser_boards[m]; - retval = mxser_get_ISA_conf(cap, brd); - - if (retval != 0) - printk(KERN_INFO "Found MOXA %s board " - "(CAP=0x%x)\n", - brd->info->name, ioaddr[b]); - - if (retval <= 0) { - if (retval == MXSER_ERR_IRQ) - printk(KERN_ERR "Invalid interrupt " - "number, board not " - "configured\n"); - else if (retval == MXSER_ERR_IRQ_CONFLIT) - printk(KERN_ERR "Invalid interrupt " - "number, board not " - "configured\n"); - else if (retval == MXSER_ERR_VECTOR) - printk(KERN_ERR "Invalid interrupt " - "vector, board not " - "configured\n"); - else if (retval == MXSER_ERR_IOADDR) - printk(KERN_ERR "Invalid I/O address, " - "board not configured\n"); - - brd->info = NULL; - continue; - } - - /* mxser_initbrd will hook ISR. */ - if (mxser_initbrd(brd, NULL) < 0) { - brd->info = NULL; - continue; - } - - brd->idx = m * MXSER_PORTS_PER_BOARD; - for (i = 0; i < brd->info->nports; i++) - tty_register_device(mxvar_sdriver, brd->idx + i, - NULL); - - m++; - } - - retval = pci_register_driver(&mxser_driver); - if (retval) { - printk(KERN_ERR "Can't register pci driver\n"); - if (!m) { - retval = -ENODEV; - goto err_unr; - } /* else: we have some ISA cards under control */ - } - - pr_debug("Done.\n"); - - return 0; -err_unr: - tty_unregister_driver(mxvar_sdriver); -err_put: - put_tty_driver(mxvar_sdriver); - return retval; -} - -static void __exit mxser_module_exit(void) -{ - unsigned int i, j; - - pr_debug("Unloading module mxser ...\n"); - - pci_unregister_driver(&mxser_driver); - - for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */ - if (mxser_boards[i].info != NULL) - for (j = 0; j < mxser_boards[i].info->nports; j++) - tty_unregister_device(mxvar_sdriver, - mxser_boards[i].idx + j); - tty_unregister_driver(mxvar_sdriver); - put_tty_driver(mxvar_sdriver); - - for (i = 0; i < MXSER_BOARDS; i++) - if (mxser_boards[i].info != NULL) - mxser_release_res(&mxser_boards[i], NULL, 1); - - pr_debug("Done.\n"); -} - -module_init(mxser_module_init); -module_exit(mxser_module_exit); diff --git a/drivers/char/mxser_new.h b/drivers/char/mxser_new.h deleted file mode 100644 index 84417111595..00000000000 --- a/drivers/char/mxser_new.h +++ /dev/null @@ -1,287 +0,0 @@ -#ifndef _MXSER_H -#define _MXSER_H - -/* - * Semi-public control interfaces - */ - -/* - * MOXA ioctls - */ - -#define MOXA 0x400 -#define MOXA_GETDATACOUNT (MOXA + 23) -#define MOXA_DIAGNOSE (MOXA + 50) -#define MOXA_CHKPORTENABLE (MOXA + 60) -#define MOXA_HighSpeedOn (MOXA + 61) -#define MOXA_GET_MAJOR (MOXA + 63) -#define MOXA_GETMSTATUS (MOXA + 65) -#define MOXA_SET_OP_MODE (MOXA + 66) -#define MOXA_GET_OP_MODE (MOXA + 67) - -#define RS232_MODE 0 -#define RS485_2WIRE_MODE 1 -#define RS422_MODE 2 -#define RS485_4WIRE_MODE 3 -#define OP_MODE_MASK 3 - -#define MOXA_SDS_RSTICOUNTER (MOXA + 69) -#define MOXA_ASPP_OQUEUE (MOXA + 70) -#define MOXA_ASPP_MON (MOXA + 73) -#define MOXA_ASPP_LSTATUS (MOXA + 74) -#define MOXA_ASPP_MON_EXT (MOXA + 75) -#define MOXA_SET_BAUD_METHOD (MOXA + 76) - -/* --------------------------------------------------- */ - -#define NPPI_NOTIFY_PARITY 0x01 -#define NPPI_NOTIFY_FRAMING 0x02 -#define NPPI_NOTIFY_HW_OVERRUN 0x04 -#define NPPI_NOTIFY_SW_OVERRUN 0x08 -#define NPPI_NOTIFY_BREAK 0x10 - -#define NPPI_NOTIFY_CTSHOLD 0x01 /* Tx hold by CTS low */ -#define NPPI_NOTIFY_DSRHOLD 0x02 /* Tx hold by DSR low */ -#define NPPI_NOTIFY_XOFFHOLD 0x08 /* Tx hold by Xoff received */ -#define NPPI_NOTIFY_XOFFXENT 0x10 /* Xoff Sent */ - -/* follow just for Moxa Must chip define. */ -/* */ -/* when LCR register (offset 0x03) write following value, */ -/* the Must chip will enter enchance mode. And write value */ -/* on EFR (offset 0x02) bit 6,7 to change bank. */ -#define MOXA_MUST_ENTER_ENCHANCE 0xBF - -/* when enhance mode enable, access on general bank register */ -#define MOXA_MUST_GDL_REGISTER 0x07 -#define MOXA_MUST_GDL_MASK 0x7F -#define MOXA_MUST_GDL_HAS_BAD_DATA 0x80 - -#define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */ -/* enchance register bank select and enchance mode setting register */ -/* when LCR register equal to 0xBF */ -#define MOXA_MUST_EFR_REGISTER 0x02 -/* enchance mode enable */ -#define MOXA_MUST_EFR_EFRB_ENABLE 0x10 -/* enchance reister bank set 0, 1, 2 */ -#define MOXA_MUST_EFR_BANK0 0x00 -#define MOXA_MUST_EFR_BANK1 0x40 -#define MOXA_MUST_EFR_BANK2 0x80 -#define MOXA_MUST_EFR_BANK3 0xC0 -#define MOXA_MUST_EFR_BANK_MASK 0xC0 - -/* set XON1 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XON1_REGISTER 0x04 - -/* set XON2 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XON2_REGISTER 0x05 - -/* set XOFF1 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XOFF1_REGISTER 0x06 - -/* set XOFF2 value register, when LCR=0xBF and change to bank0 */ -#define MOXA_MUST_XOFF2_REGISTER 0x07 - -#define MOXA_MUST_RBRTL_REGISTER 0x04 -#define MOXA_MUST_RBRTH_REGISTER 0x05 -#define MOXA_MUST_RBRTI_REGISTER 0x06 -#define MOXA_MUST_THRTL_REGISTER 0x07 -#define MOXA_MUST_ENUM_REGISTER 0x04 -#define MOXA_MUST_HWID_REGISTER 0x05 -#define MOXA_MUST_ECR_REGISTER 0x06 -#define MOXA_MUST_CSR_REGISTER 0x07 - -/* good data mode enable */ -#define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20 -/* only good data put into RxFIFO */ -#define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10 - -/* enable CTS interrupt */ -#define MOXA_MUST_IER_ECTSI 0x80 -/* enable RTS interrupt */ -#define MOXA_MUST_IER_ERTSI 0x40 -/* enable Xon/Xoff interrupt */ -#define MOXA_MUST_IER_XINT 0x20 -/* enable GDA interrupt */ -#define MOXA_MUST_IER_EGDAI 0x10 - -#define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI) - -/* GDA interrupt pending */ -#define MOXA_MUST_IIR_GDA 0x1C -#define MOXA_MUST_IIR_RDA 0x04 -#define MOXA_MUST_IIR_RTO 0x0C -#define MOXA_MUST_IIR_LSR 0x06 - -/* recieved Xon/Xoff or specical interrupt pending */ -#define MOXA_MUST_IIR_XSC 0x10 - -/* RTS/CTS change state interrupt pending */ -#define MOXA_MUST_IIR_RTSCTS 0x20 -#define MOXA_MUST_IIR_MASK 0x3E - -#define MOXA_MUST_MCR_XON_FLAG 0x40 -#define MOXA_MUST_MCR_XON_ANY 0x80 -#define MOXA_MUST_MCR_TX_XON 0x08 - -/* software flow control on chip mask value */ -#define MOXA_MUST_EFR_SF_MASK 0x0F -/* send Xon1/Xoff1 */ -#define MOXA_MUST_EFR_SF_TX1 0x08 -/* send Xon2/Xoff2 */ -#define MOXA_MUST_EFR_SF_TX2 0x04 -/* send Xon1,Xon2/Xoff1,Xoff2 */ -#define MOXA_MUST_EFR_SF_TX12 0x0C -/* don't send Xon/Xoff */ -#define MOXA_MUST_EFR_SF_TX_NO 0x00 -/* Tx software flow control mask */ -#define MOXA_MUST_EFR_SF_TX_MASK 0x0C -/* don't receive Xon/Xoff */ -#define MOXA_MUST_EFR_SF_RX_NO 0x00 -/* receive Xon1/Xoff1 */ -#define MOXA_MUST_EFR_SF_RX1 0x02 -/* receive Xon2/Xoff2 */ -#define MOXA_MUST_EFR_SF_RX2 0x01 -/* receive Xon1,Xon2/Xoff1,Xoff2 */ -#define MOXA_MUST_EFR_SF_RX12 0x03 -/* Rx software flow control mask */ -#define MOXA_MUST_EFR_SF_RX_MASK 0x03 - -#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_FIFO_VALUE(info) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((info)->ioaddr+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR);\ - __efr = inb((info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ - outb((u8)((info)->rx_high_water), (info)->ioaddr+ \ - MOXA_MUST_RBRTH_REGISTER); \ - outb((u8)((info)->rx_trigger), (info)->ioaddr+ \ - MOXA_MUST_RBRTI_REGISTER); \ - outb((u8)((info)->rx_low_water), (info)->ioaddr+ \ - MOXA_MUST_RBRTL_REGISTER); \ - outb(__oldlcr, (info)->ioaddr+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_TX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_RX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} while (0) - -#endif