From: Paul Mundt Date: Wed, 17 Dec 2008 05:41:54 +0000 (+0900) Subject: sh: Kill off cf-enabler with extreme prejudice. X-Git-Tag: v2.6.29-rc1~591^2~20 X-Git-Url: http://pilppa.com/gitweb/?a=commitdiff_plain;h=073da9c0de401e8683b6bc76c008a7e0850045d5;p=linux-2.6-omap-h63xx.git sh: Kill off cf-enabler with extreme prejudice. Now that the rest of the boards that were using cf-enabler "generically" have switched to setting up their mappings on their own, only the mach-se boards were left using it. All of the cf-enabler using mach-se boards use a special initialization of the MRSHPC windows rather than going through the special PTE as other SH-4 platforms do. This consolidates the MRSHPC setup logic, hooks it up on the boards that care, and gets rid of any and all remaining references to cf-enabler. This has been long overdue, as cf-enabler has been the bane of arch/sh/kernel for the last 7 years. Good riddance. Signed-off-by: Paul Mundt --- diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig index 57fd4983cc1..03c773b74bd 100644 --- a/arch/sh/Kconfig +++ b/arch/sh/Kconfig @@ -701,49 +701,6 @@ config MAPLE Dreamcast with a serial line terminal or a remote network connection. -config CF_ENABLER - bool "Compact Flash Enabler support" - depends on SOLUTION_ENGINE - ---help--- - Compact Flash is a small, removable mass storage device introduced - in 1994 originally as a PCMCIA device. If you say `Y' here, you - compile in support for Compact Flash devices directly connected to - a SuperH processor. A Compact Flash FAQ is available at - . - - If your board has "Directly Connected" CompactFlash at area 5 or 6, - you may want to enable this option. Then, you can use CF as - primary IDE drive (only tested for SanDisk). - - If in doubt, select 'N'. - -choice - prompt "Compact Flash Connection Area" - depends on CF_ENABLER - default CF_AREA6 - -config CF_AREA5 - bool "Area5" - help - If your board has "Directly Connected" CompactFlash, You should - select the area where your CF is connected to. - - - "Area5" if CompactFlash is connected to Area 5 (0x14000000) - - "Area6" if it is connected to Area 6 (0x18000000) - - "Area6" will work for most boards. - -config CF_AREA6 - bool "Area6" - -endchoice - -config CF_BASE_ADDR - hex - depends on CF_ENABLER - default "0xb8000000" if CF_AREA6 - default "0xb4000000" if CF_AREA5 - source "arch/sh/drivers/pci/Kconfig" source "drivers/pci/Kconfig" diff --git a/arch/sh/boards/mach-se/770x/setup.c b/arch/sh/boards/mach-se/770x/setup.c index 9123d9687bf..527eb6b1261 100644 --- a/arch/sh/boards/mach-se/770x/setup.c +++ b/arch/sh/boards/mach-se/770x/setup.c @@ -8,8 +8,9 @@ */ #include #include -#include #include +#include +#include #include #include #include @@ -175,6 +176,7 @@ static struct platform_device *se_devices[] __initdata = { static int __init se_devices_setup(void) { + mrshpc_setup_windows(); return platform_add_devices(se_devices, ARRAY_SIZE(se_devices)); } device_initcall(se_devices_setup); diff --git a/arch/sh/boards/mach-se/7721/setup.c b/arch/sh/boards/mach-se/7721/setup.c index d3fc80ff4d8..55af4c36b43 100644 --- a/arch/sh/boards/mach-se/7721/setup.c +++ b/arch/sh/boards/mach-se/7721/setup.c @@ -12,8 +12,9 @@ */ #include #include -#include #include +#include +#include #include #include @@ -74,8 +75,8 @@ static struct platform_device *se7721_devices[] __initdata = { static int __init se7721_devices_setup(void) { - return platform_add_devices(se7721_devices, - ARRAY_SIZE(se7721_devices)); + mrshpc_setup_windows(); + return platform_add_devices(se7721_devices, ARRAY_SIZE(se7721_devices)); } device_initcall(se7721_devices_setup); diff --git a/arch/sh/boards/mach-se/7722/setup.c b/arch/sh/boards/mach-se/7722/setup.c index 02035bbf2cc..af84904ed86 100644 --- a/arch/sh/boards/mach-se/7722/setup.c +++ b/arch/sh/boards/mach-se/7722/setup.c @@ -15,9 +15,10 @@ #include #include #include +#include +#include #include #include -#include #include #include #include @@ -147,8 +148,8 @@ static struct platform_device *se7722_devices[] __initdata = { static int __init se7722_devices_setup(void) { - return platform_add_devices(se7722_devices, - ARRAY_SIZE(se7722_devices)); + mrshpc_setup_windows(); + return platform_add_devices(se7722_devices, ARRAY_SIZE(se7722_devices)); } device_initcall(se7722_devices_setup); diff --git a/arch/sh/include/mach-se/mach/mrshpc.h b/arch/sh/include/mach-se/mach/mrshpc.h new file mode 100644 index 00000000000..95c8b825401 --- /dev/null +++ b/arch/sh/include/mach-se/mach/mrshpc.h @@ -0,0 +1,52 @@ +#ifndef __MACH_SE_MRSHPC_H +#define __MACH_SE_MRSHPC_H + +#include + +static void __init mrshpc_setup_windows(void) +{ + if ((__raw_readw(MRSHPC_CSR) & 0x000c) != 0) + return; /* Not detected */ + + if ((__raw_readw(MRSHPC_CSR) & 0x0080) == 0) { + __raw_writew(0x0674, MRSHPC_CPWCR); /* Card Vcc is 3.3v? */ + } else { + __raw_writew(0x0678, MRSHPC_CPWCR); /* Card Vcc is 5V */ + } + + /* + * PC-Card window open + * flag == COMMON/ATTRIBUTE/IO + */ + /* common window open */ + __raw_writew(0x8a84, MRSHPC_MW0CR1); + if((__raw_readw(MRSHPC_CSR) & 0x4000) != 0) + /* common mode & bus width 16bit SWAP = 1*/ + __raw_writew(0x0b00, MRSHPC_MW0CR2); + else + /* common mode & bus width 16bit SWAP = 0*/ + __raw_writew(0x0300, MRSHPC_MW0CR2); + + /* attribute window open */ + __raw_writew(0x8a85, MRSHPC_MW1CR1); + if ((__raw_readw(MRSHPC_CSR) & 0x4000) != 0) + /* attribute mode & bus width 16bit SWAP = 1*/ + __raw_writew(0x0a00, MRSHPC_MW1CR2); + else + /* attribute mode & bus width 16bit SWAP = 0*/ + __raw_writew(0x0200, MRSHPC_MW1CR2); + + /* I/O window open */ + __raw_writew(0x8a86, MRSHPC_IOWCR1); + __raw_writew(0x0008, MRSHPC_CDCR); /* I/O card mode */ + if ((__raw_readw(MRSHPC_CSR) & 0x4000) != 0) + __raw_writew(0x0a00, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 1*/ + else + __raw_writew(0x0200, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 0*/ + + __raw_writew(0x2000, MRSHPC_ICR); + __raw_writeb(0x00, PA_MRSHPC_MW2 + 0x206); + __raw_writeb(0x42, PA_MRSHPC_MW2 + 0x200); +} + +#endif /* __MACH_SE_MRSHPC_H */ diff --git a/arch/sh/kernel/Makefile_32 b/arch/sh/kernel/Makefile_32 index df25304ad78..3c975ab4559 100644 --- a/arch/sh/kernel/Makefile_32 +++ b/arch/sh/kernel/Makefile_32 @@ -17,7 +17,6 @@ obj-y := debugtraps.o disassemble.o idle.o io.o io_generic.o irq.o \ obj-y += cpu/ timers/ obj-$(CONFIG_VSYSCALL) += vsyscall/ obj-$(CONFIG_SMP) += smp.o -obj-$(CONFIG_CF_ENABLER) += cf-enabler.o obj-$(CONFIG_SH_STANDARD_BIOS) += sh_bios.o obj-$(CONFIG_KGDB) += kgdb.o obj-$(CONFIG_SH_CPU_FREQ) += cpufreq.o diff --git a/arch/sh/kernel/Makefile_64 b/arch/sh/kernel/Makefile_64 index 678408cc35c..fe425d7f687 100644 --- a/arch/sh/kernel/Makefile_64 +++ b/arch/sh/kernel/Makefile_64 @@ -7,7 +7,6 @@ obj-y := debugtraps.o idle.o io.o io_generic.o irq.o machvec.o process_64.o \ obj-y += cpu/ timers/ obj-$(CONFIG_VSYSCALL) += vsyscall/ obj-$(CONFIG_SMP) += smp.o -obj-$(CONFIG_CF_ENABLER) += cf-enabler.o obj-$(CONFIG_SH_STANDARD_BIOS) += sh_bios.o obj-$(CONFIG_SH_CPU_FREQ) += cpufreq.o obj-$(CONFIG_MODULES) += sh_ksyms_64.o module.o diff --git a/arch/sh/kernel/cf-enabler.c b/arch/sh/kernel/cf-enabler.c deleted file mode 100644 index bea40339919..00000000000 --- a/arch/sh/kernel/cf-enabler.c +++ /dev/null @@ -1,168 +0,0 @@ -/* $Id: cf-enabler.c,v 1.4 2004/02/22 22:44:36 kkojima Exp $ - * - * linux/drivers/block/cf-enabler.c - * - * Copyright (C) 1999 Niibe Yutaka - * Copyright (C) 2000 Toshiharu Nozawa - * Copyright (C) 2001 A&D Co., Ltd. - * - * Enable the CF configuration. - */ - -#include -#include -#include -#include -#include -#include - -/* - * You can connect Compact Flash directly to the bus of SuperH. - * This is the enabler for that. - * - * SIM: How generic is this really? It looks pretty board, or at - * least SH sub-type, specific to me. - * I know it doesn't work on the Overdrive! - */ - -/* - * 0xB8000000 : Attribute - * 0xB8001000 : Common Memory - * 0xBA000000 : I/O - */ -#if defined(CONFIG_CPU_SH4) -/* SH4 can't access PCMCIA interface through P2 area. - * we must remap it with appropriate attribute bit of the page set. - * this part is based on Greg Banks' hd64465_ss.c implementation - Masahiro Abe */ - -#if defined(CONFIG_CF_AREA6) -#define slot_no 0 -#else -#define slot_no 1 -#endif - -/* use this pointer to access to directly connected compact flash io area*/ -void *cf_io_base; - -static int __init allocate_cf_area(void) -{ - pgprot_t prot; - unsigned long paddrbase, psize; - - /* open I/O area window */ - paddrbase = virt_to_phys((void*)CONFIG_CF_BASE_ADDR); - psize = PAGE_SIZE; - prot = PAGE_KERNEL_PCC(slot_no, _PAGE_PCC_IO16); - cf_io_base = p3_ioremap(paddrbase, psize, prot.pgprot); - if (!cf_io_base) { - printk("allocate_cf_area : can't open CF I/O window!\n"); - return -ENOMEM; - } -/* printk("p3_ioremap(paddr=0x%08lx, psize=0x%08lx, prot=0x%08lx)=0x%08lx\n", - paddrbase, psize, prot.pgprot, cf_io_base);*/ - - /* XXX : do we need attribute and common-memory area also? */ - - return 0; -} -#endif - -static int __init cf_init_default(void) -{ -/* You must have enabled the card, and set the level interrupt - * before reaching this point. Possibly in boot ROM or boot loader. - */ -#if defined(CONFIG_CPU_SH4) - allocate_cf_area(); -#endif - - return 0; -} - -#if defined(CONFIG_SH_SOLUTION_ENGINE) -#include -#elif defined(CONFIG_SH_7722_SOLUTION_ENGINE) -#include -#elif defined(CONFIG_SH_7721_SOLUTION_ENGINE) -#include -#endif - -/* - * SolutionEngine Seriese - * - * about MS770xSE - * 0xB8400000 : Common Memory - * 0xB8500000 : Attribute - * 0xB8600000 : I/O - * - * about MS7722SE - * 0xB0400000 : Common Memory - * 0xB0500000 : Attribute - * 0xB0600000 : I/O - */ - -#if defined(CONFIG_SH_SOLUTION_ENGINE) || \ - defined(CONFIG_SH_7722_SOLUTION_ENGINE) || \ - defined(CONFIG_SH_7721_SOLUTION_ENGINE) -static int __init cf_init_se(void) -{ - if ((ctrl_inw(MRSHPC_CSR) & 0x000c) != 0) - return 0; /* Not detected */ - - if ((ctrl_inw(MRSHPC_CSR) & 0x0080) == 0) { - ctrl_outw(0x0674, MRSHPC_CPWCR); /* Card Vcc is 3.3v? */ - } else { - ctrl_outw(0x0678, MRSHPC_CPWCR); /* Card Vcc is 5V */ - } - - /* - * PC-Card window open - * flag == COMMON/ATTRIBUTE/IO - */ - /* common window open */ - ctrl_outw(0x8a84, MRSHPC_MW0CR1); - if((ctrl_inw(MRSHPC_CSR) & 0x4000) != 0) - /* common mode & bus width 16bit SWAP = 1*/ - ctrl_outw(0x0b00, MRSHPC_MW0CR2); - else - /* common mode & bus width 16bit SWAP = 0*/ - ctrl_outw(0x0300, MRSHPC_MW0CR2); - - /* attribute window open */ - ctrl_outw(0x8a85, MRSHPC_MW1CR1); - if ((ctrl_inw(MRSHPC_CSR) & 0x4000) != 0) - /* attribute mode & bus width 16bit SWAP = 1*/ - ctrl_outw(0x0a00, MRSHPC_MW1CR2); - else - /* attribute mode & bus width 16bit SWAP = 0*/ - ctrl_outw(0x0200, MRSHPC_MW1CR2); - - /* I/O window open */ - ctrl_outw(0x8a86, MRSHPC_IOWCR1); - ctrl_outw(0x0008, MRSHPC_CDCR); /* I/O card mode */ - if ((ctrl_inw(MRSHPC_CSR) & 0x4000) != 0) - ctrl_outw(0x0a00, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 1*/ - else - ctrl_outw(0x0200, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 0*/ - - ctrl_outw(0x2000, MRSHPC_ICR); - ctrl_outb(0x00, PA_MRSHPC_MW2 + 0x206); - ctrl_outb(0x42, PA_MRSHPC_MW2 + 0x200); - return 0; -} -#else -static int __init cf_init_se(void) -{ - return -1; -} -#endif - -static int __init cf_init(void) -{ - if (mach_is_se() || mach_is_7722se() || mach_is_7721se()) - return cf_init_se(); - - return cf_init_default(); -} - -__initcall (cf_init);